Dynamically assign host PIDs to guest PIDs, splitting each guest PID into
multiple host (shadow) PIDs based on kernel/user and MSR[IS/DS]. Use
both PID0 and PID1 so that the shadow PIDs for the right mode can be
selected, that correspond both to guest TID = zero and guest TID = guest
PID.
This allows us to significantly reduce the frequency of needing to
invalidate the entire TLB. When the guest mode or PID changes, we just
update the host PID0/PID1. And since the allocation of shadow PIDs is
global, multiple guests can share the TLB without conflict.
Note that KVM does not yet support the guest setting PID1 or PID2 to
a value other than zero. This will need to be fixed for nested KVM
to work. Until then, we enforce the requirement for guest PID1/PID2
to stay zero by failing the emulation if the guest tries to set them
to something else.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is done lazily. The SPE save will be done only if the guest has
used SPE since the last preemption or heavyweight exit. Restore will be
done only on demand, when enabling MSR_SPE in the shadow MSR, in response
to an SPE fault or mtmsr emulation.
For SPEFSCR, Linux already switches it on context switch (non-lazily), so
the only remaining bit is to save it between qemu and the guest.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
BookE also wants to support level based interrupts, so let's implement
all the necessary logic there. We need to trick a bit here because the
irqprios are 1:1 assigned to architecture defined values. But since there
is some space left there, we can just pick a random one and move it later
on - it's internal anyways.
Signed-off-by: Alexander Graf <agraf@suse.de>
One of the most obvious registers to share with the guest directly is the
MSR. The MSR contains the "interrupts enabled" flag which the guest has to
toggle in critical sections.
So in order to bring the overhead of interrupt en- and disabling down, let's
put msr into the shared page. Keep in mind that even though you can fully read
its contents, writing to it doesn't always update all state. There are a few
safe fields that don't require hypervisor interaction. See the documentation
for a list of MSR bits that are safe to be set from inside the guest.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Avi Kivity <avi@redhat.com>
Although BOOKE_MAX_INTERRUPT has the right value, the meaning is not match.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
The Book E code will be shared with e500.
I've left PID in kvmppc_core_emulate_op() just so that we don't need to move
kvmppc_set_pid() right now. Once we have the e500 implementation, we can
probably share that too.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Existing KVM statistics are either just counters (kvm_stat) reported for
KVM generally or trace based aproaches like kvm_trace.
For KVM on powerpc we had the need to track the timings of the different exit
types. While this could be achieved parsing data created with a kvm_trace
extension this adds too much overhead (at least on embedded PowerPC) slowing
down the workloads we wanted to measure.
Therefore this patch adds a in-kernel exit timing statistic to the powerpc kvm
code. These statistic is available per vm&vcpu under the kvm debugfs directory.
As this statistic is low, but still some overhead it can be enabled via a
.config entry and should be off by default.
Since this patch touched all powerpc kvm_stat code anyway this code is now
merged and simplified together with the exit timing statistic code (still
working with exit timing disabled in .config).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
In kvmppc_deliver_interrupt is just one case left in the switch and it is a
rare one (less than 8%) when looking at the exit numbers. Therefore we can
at least drop the switch/case and if an if. I inserted an unlikely too, but
that's open for discussion.
In kvmppc_can_deliver_interrupt all frequent cases are in the default case.
I know compilers are smart but we can make it easier for them. By writing
down all options and removing the default case combined with the fact that
ithe values are constants 0..15 should allow the compiler to write an easy
jump table.
Modifying kvmppc_can_deliver_interrupt pointed me to the fact that gcc seems
to be unable to reduce priority_exception[x] to a build time constant.
Therefore I changed the usage of the translation arrays in the interrupt
delivery path completely. It is now using priority without translation to irq
on the full irq delivery path.
To be able to do that ivpr regs are stored by their priority now.
Additionally the decision made in kvmppc_can_deliver_interrupt is already
sufficient to get the value of interrupt_msr_mask[x]. Therefore we can replace
the 16x4byte array used here with a single 4byte variable (might still be one
miss, but the chance to find this in cache should be better than the right
entry of the whole array).
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Cores provide 3 emulation hooks, implemented for example in the new
4xx_emulate.c:
kvmppc_core_emulate_op
kvmppc_core_emulate_mtspr
kvmppc_core_emulate_mfspr
Strictly speaking the last two aren't necessary, but provide for more
informative error reporting ("unknown SPR").
Long term I'd like to have instruction decoding autogenerated from tables of
opcodes, and that way we could aggregate universal, Book E, and core-specific
instructions more easily and without redundant switch statements.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
