Introduce a 'internal-regs' subnode, under which all devices are
moved. This is not really needed for now, but will be for the
mvebu-mbus driver. This generates a lot of code movement since it's
indenting by one more tab all the devices. So it was a good
opportunity to fix all the bad indentation.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This conversion will allow to keep 32 bits addresses for the internal
registers whereas the memory of the system will be 64 bits.
Later it will also ease the move of the mvebu-mbus driver to the
device tree support.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- Kirkwood
- a couple of small fixes for the Iomega ix2-200 board (ether and led)
- mvebu
- allow GPIO button to work on Mirabox when running SMP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRZZxwAAoJEAi3KVZQDZAerwcIAKR1xRKuagtXvfij+xfVVRQ6
1G645hTIthFXmNiEeo3Y/mswHhVooZvu8SWh3o3J2Wsbnzeh+ch6jTsl+g6Tnb3E
KmRFU0mcalRmsyYsh4PH9nDi8/oWyP+i3ZytgfcMlsSPNiE+Ek35NdTTWMLCTT8V
MkGysVc8MWoOmMf47mNboy5UUUTXRdnSUJSjv1ubrsTK33LT7Ii9Ce+eoNvpvF+5
+6RenfRMzRSwkZf9AaCRPAhXISQKbMAwz6lKGo2GGAW+73Z+JclXXmiCfQ8pWie2
pfyqiEYigZFqe6Ly5BUtGoVfDjmOLDs+ATTUDOlOj0uaEc7pOwwKoAtpVRdck24=
=yK1f
-----END PGP SIGNATURE-----
Merge tag 'tags/mvebu_fixes_for_v3.9_round3' into mvebu/dt
pulling in mvebu branches which changes armada*.dts? files for LPAE changes
mvebu fixes for v3.9 round 3
- Kirkwood
- a couple of small fixes for the Iomega ix2-200 board (ether and led)
- mvebu
- allow GPIO button to work on Mirabox when running SMP
The Globalscale Mirabox platform uses one PCIe interface for an
available mini-PCIe slot, and the other PCIe interface for an internal
USB 3.0 controller. We add the necessary Device Tree informations to
enable those two interfaces.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the three external LED definitions to the device tree file on
the Mirabox.
The Mirabox user guide calls out one as a power LED, and the other
two are defined for WiFi, but as the current mwifiex drivers don't
have LED support, we make them status LEDs.
These have been tested working by writing to the appropriate
/sys/class/leds trigger.
Signed-off-by: Ryan Press <ryan@presslab.us>
Tested-by: Neil Greatorex <neil@fatboyfat.co.uk>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The previous configuration used the wrong "clk" pin. Without this
change mv_sdio worked because the bootloader would set the pin up, but
with a bootloader that does not set the pin, mv_sdio fails to detect any
card.
I have tested this change using a mwifiex_sdio wireless network adapter
over the SDIO interface.
Signed-off-by: Ryan Press <ryan@presslab.us>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Globalscale Mirabox platform can be connected to the JTAG/GPIO box
through the Multi-IO port. The GPIO box use the NXP PCA9505 I/O port
expansion IC to provide 40-bit parallel input/output GPIOs. This patch
enable the use of this expander on the Mirabox.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This patch activates every USB port provided by each SoC.
Except for Armada XP Openblocks AX3-4 board,
where we enable only the first two USB ports
until we have more information on the third one usage.
Cc: Lior Amsalem <alior@marvell.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Globalscale Mirabox uses the SDIO interface of the Armada 370 to
connect to a Wifi/Bluetooth SD8787 chip, so we enable the SDIO
interface of this board in its Device Tree file.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The mvneta driver for the Marvell Armada 370/XP Ethernet devices has
gained proper clock framework integration, and the corresponding
Device Tree nodes now have a correct 'clocks' pointer.
The 'clock-frequency' properties in the various .dts files for Armada
370/XP boards have therefore become useless.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The Globalscale Mirabox platform has two Ethernet interfaces,
connected to the SoC with a RGMII interface.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
This platform, available from Globalscale has an Armada 370. For now,
only the serial port is supported. Support for network, USB and other
peripherals will be added as drivers for them become available for
Armada 370 in mainline.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
---
This is 3.8 material.
Changes from original version posted by Gregory:
* Renamed .dts file to armada-370-mirabox.dts
* Change compatible string to 'globalscale,mirabox'
* Remove compatible string from armada-370-xp.c
* Removed references to MBX0001
