Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the same way as for msm8974-hammerhead, l11 load, used for SDCARD
VMMC, needs to be increased in order to prevent any voltage drop issues
(due to limited current) happening with some SDCARDS or during specific
operations (e.g. write).
Tested on Dragonboard-410c and DART-SD410 boards.
Fixes: 4c7d53d16d (arm64: dts: apq8016-sbc: add regulators support)
Reported-by: Manabu Igusa <migusa@arrowjapan.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Resin is board specific so add the resin node in apq8016-sbc dtsi
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Current LED trigger, 'bt', is not known/used by any existing driver.
Fix this by renaming it to 'bluetooth-power' trigger which is
controlled by the Bluetooth subsystem.
Fixes: 9943230c88 ("arm64: dts: qcom: Add apq8016-sbc board LED's related device nodes")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Blink the LED on a kernel panic.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Pull "Qualcomm ARM64 Updates for v4.15" from Andy Gross:
* Add PCIE support to relevant MSM8996 based boards
* Add RPM clock controller node on MSM8996
* Add dload address on MSM8916 and MSM8996
* Add MBHC button support on APQ8016 SBC
* Add RTMFS specific compatible for rmtfs memory node
* Fixups for MSM8916 GPIO line names and MDP address length
* tag 'qcom-arm64-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: msm8916: Mark rmtfs node as qcom, rmtfs-mem compatible
arm64: dts: msm8996: Add the rpm clock controller node
arm64: dts: qcom: sbc: Name GPIO lines
arm64: dts: qcom: msm8916: Shrink mdp address length for msm8916
arm64: dts: apq8016-sbc: add mbhc buttons support
arm64: dts: qcom: Specify dload address for msm8916 and msm8996
arm64: dts: apq8096-db820c: never disable regulator on LS expansion
arm64: dts: apq8096-db820c: Enable on board 3 pcie root complex
arm64: dts: qcom: msm8996: add support to pcie
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm64/boot/dts -type -f -name '*.dts*'
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This names the GPIO lines on the APQ8016 "SBC" also known
as the DragonBoard 410c, according to the schematic. This
is necessary for a conforming userspace looking across
all GPIO chips for the GPIO lines named "GPIO-A" thru
"GPIO-L".
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The adv7533 on this board needs a cec clock. Hook it up in the dtsi
to enable CEC for the HDMI transmitters.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Commit ed75d6a969 ("arm64: dts: qcom: Collapse usb support into
one node") breaks host mode support on apq8016-sbc boards. This
is because the mux driver (tc7usb40mu) hasn't been merged.
Without that driver, we can't toggle the GPIO going to the mux to
route out the D+/D- lines to the USB hub that's on the board.
One solution would be to totally revert this change, but that
opens us up to other problems when two USB drivers are operating
the same hardware block at the same time. Let's modify the DT so
that the USB controller is always in host mode and connected to
the hub so that things like USB keyboards and mouses work. This
is the mode that most people prefer anyway with these devices. We
also delete the usb-switch node because the binding was never
accepted upstream.
In the future, we can add muxing support and then update the DT
to support both modes at runtime. Patches to support this are
already on the mailing list.
Fixes: ed75d6a969 ("arm64: dts: qcom: Collapse usb support into one node")
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The TX status trigger of the wlan interface is named phy0tx, so this
updates the default-trigger for the WLAN LED to use that instead.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
We currently have three device nodes for the same USB hardware
block, as evident by the reuse of the same reg address multiple
times. Now that the chipidea driver fully supports OTG with the
MSM wrapper we can collapse all these nodes into one USB device
node, reflecting the true nature of the hardware.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Declare a ramoops memory segment to aid debugging for those without UART
access. Verified to carry console log when holding volume down for 15
seconds.
No memory region for ramoops-like support was found downstream, so the
arbitrarily picked region is the last MB of System RAM.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Mart Raudsepp <leio@gentoo.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
VOL/ZOOM+ button on DB410c is connected to
SoC GPIO 104. Add support for it.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds support to hdmi audio via adv7533.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the wcnss remoteproc node the SMD edge and the wcnss ctrl, bluetooth
and wifi nodes specified and enable this on db410c.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch add support to Analog audio both Playback and Capture via
msm8916 WCD muti codec.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
On the APQ8016 SBC, the LDO2 PM8916 regulator feeds 1.2V to the following:
- VDDA_1P2_MIPI_DSI and VDDA_MIPI_CSI pins on APQ8016.
- VCCCAD pins on the LPDDR3 chip.
- VDDPX_1 pins on APQ8016.
The LDO6 regulator feeds 1.8V to:
- VDAA_MIPI_DSI0_PLL pin on APQ8016.
- QFPROM_BLOW_VDD pin on PM8916.
- The AVDD, A2VDD and DVDD pins on ADV7533 bridge.
The LDO17 regulator feeds 3.3V to:
- The V3P3 pin on ADV7533 bridge.
Currently, the regulator min/max voltages for all the LDOs are set to the
range of what the PMIC supports. Set the ranges for L2, L6 and L17 to what
we need, i.e. 1.2V, 1.8V and 3.3V respectively.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The APQ8016-sbc provides a HDMI output. The APQ8016 display block only
provides a MIPI DSI output. So, the board has a ADV7533 DSI to HDMI
encoder chip that sits between the DSI PHY output and the HDMI
connector.
Add the ADV7533 DT node under its I2C control bus, and tie the DSI
output port to the ADV7533's input port.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables bam dma node, dma is used for both tx and rx on spi
and on high speed serial.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the necessary properties to enable the SD-card on db410c boards.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables the lpass on DB410C. LPASS is used as cpu dai for
both analog and digital audio.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
This patch adds real regulators and pinctrl nodes for sdhc_1.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
To be consistent with other nodes move sdhci node under the soc node,
rather than using lable references.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
96boards mezzanine boards on LS expansion require 1.8v as per 96boards
specifications, so enable the corresponding regulators and make them
always-on.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds aliases to spi device so that it can get proper bus
number rather than a random number.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
* Add fixed rate oscillators to dts
* Fixup PMIC alias and properties
* Change 8916-MTP compatible to be compliant with new scheme
* Fix 8x16 UART pinctrl configuration
* Add SMEM, RPM/SMD, and PM8916 support on MSM8916
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mu4g
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt64
Qualcomm ARM64 Updates for v4.5
* Add fixed rate oscillators to dts
* Fixup PMIC alias and properties
* Change 8916-MTP compatible to be compliant with new scheme
* Fix 8x16 UART pinctrl configuration
* Add SMEM, RPM/SMD, and PM8916 support on MSM8916
* tag 'qcom-arm64-for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: Add PM8916 support on MSM8916
arm64: dts: qcom: Add RPM/SMD support on MSM8916
arm64: dts: qcom: Add MSM8916 SMEM nodes
arm64: dts: set the default i2c pin drive strength to 16mA
arm64: dts: fix the i2c aliasing to match to schematics.
arm64: dts: qcom: msm8916: Add fixed rate on-board oscillators
arm64: dts: qcom: Alias pm8916 on msm8916 devices
arm64: dts: qcom: Make msm8916-mtp compatible string compliant
arm64: dts: qcom: 8x16: UART1 and UART2 use DMA for RX and TX
arm64: dts: qcom: 8x16: UART1 add CTS_N, RTS_N pin configurations
Signed-off-by: Olof Johansson <olof@lixom.net>
Add label properties to provide a way to identify UART, I2C and SPI
ports based on their connector names. This follows naming convention in
96boards CE spec. Ports without external connections are not labelled.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Andy Gross <agross@codeaurora.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The LS UART0 is not used by anything else and should be enabled for
expansion boards.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Andy Gross <agross@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fixes the i2c bus number aliasing so that it matches with the
schematics bus naming.
Without this patch the user might would get bus numbers depending on
the order the devices are probed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add an alias for pm8916 on msm8916 based SoCs so that the newly
updated dtbTool can find the pmic compatible string and add the
pmic-id element to the QCDT header.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch enables spi buses on low speed and high speed expansion
connectors on DB410C
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch enables i2c buses on low speed and high speed expansion
connectors on DB410C.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Enable the eMMC on the APQ8016 SBC board (also known as DragonBoard 410c),
so that we can use its internal storage.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds the nodes required to support the UART1 node on the
MSM8916 and also fixes the sleep pins function for UART2.
Signed-off-by: Andy Gross <agross@codeaurora.org>
APQ8016 SBC board have 6 user controllable LED's.
Add following devices:
LED1 green LED triggered by system heartbeat.
LED2 green LED triggered by access to eMMC device.
LED3 green LED triggered by access to SD card.
LED4 green LED no trigger assigned.
LED5 yellow LED triggered by access to WLAN.
LED6 blue LED triggered by access to Bluetooth.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Add initial device configuration nodes for APQ8016 and PM8916 GPIO's.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
PM9816 has 2 SPMI devices per physical package. Add PMIC configuration
nodes including sub-function device nodes and include them in boards,
which are using 8x16 based chipset.
PM9816 sub-function devices include:
* GPIO block, with 4 pins
* MPP block, with 4 pins
* Volatage ADC (VADC), with multiple inputs
* Thermal sensor device, which is using on chip VADC
channel report PMIC die temperature.
* Power key device, which is responsible for clean system
reboot or shutdown
* RTC device
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Add initial device tree support for Qualcomm APQ8016 SBC Evaluation board.
This board is also referred to as the DragonBoard 410c.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Thomas Gleixner