Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add pinctrls required for camera sensors:
- power down signal;
- reset signal;
- camera external clock.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add pinctrls required for Camera Control Interface.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This node was the only one that didn't have the same set of pins in
active and suspend mode.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Nodes relative to the first sdhc node were interlaced with node of the
second sdhc. Move sdhc2_cd_pin with its siblings to prevent that. Also
rename the grouping node from sdhc2_cd_pin to pmx_sdc2_cd_pin, as
"pmx_sdc" is the prefix used by other nodes.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
These nodes reserve and configure some pins as GPIOs. They are not
generic pinctrls, they actually belong to board files but they are not
used by any other node, so just drop them altogether.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Drop assignments to bias-disable as the documentation [1] states that
this property doesn't take a value. Other occurrences of this property
respect that.
[1] Documentation/devicetree/bindings/pinctrl/qcom,msm8916-pinctrl.txt
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the wcnss remoteproc node the SMD edge and the wcnss ctrl, bluetooth
and wifi nodes specified and enable this on db410c.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
2mA drive strenght is not enough to drive chipselect low on hardware
configurations with level shifters, 16mA should give good range to
allow such configurations to work.
This issue was noticed while testing spi on db410c with sensor board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch removes redundant pins from spi pinconf as these are already
specified in pinconf_cs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
2mA drive strength is not enough when we connect multiple i2c devices
on the bus with different pull up resistors.
This issue was detected when multiple i2c devices connected on the other side
of level shifters on Linaro sensor board. Maxing up to 16mA made i2c much stable.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add devicetree bindings for UART1 CTS_N and RTS_N pins.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds missing support for i2c0 and i2c6, this support is
required to connect the i2c slaves on LS expansion on DB410c.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch fixes the i2c pinctrl sleep state by changing the pinconf
function to be in gpio mode rather than i2c.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
This patch adds the nodes required to support the UART1 node on the
MSM8916 and also fixes the sleep pins function for UART2.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Create separate file for MSM8916 pinctrl default/sleep pins state
definitions. Move in UART2 states and add SPI, I2C and SDC configurations.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Thomas Gleixner