Adds a function that sets the pointer to dev_pm_domain in struct device
and that warns if the device has already finished probing. The reason
why we want to enforce that is because in the general case that can
cause problems and also that we can simplify code quite a bit if we can
always assume that.
This patch also changes all current code that directly sets the
dev.pm_domain pointer.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-domains:
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
PM / Domains: Validate cases of a non-bound driver in genpd governor
* pm-cpufreq:
cpufreq: use last policy after online for drivers with ->setpolicy
It looks like these meant to be unreffing the
of_parse_phandle_with_args() node, since the error paths above it
don't do of_node_put. That function returns a new ref in pd_args.np,
though, not a new ref on dev->of_node. Also, it would have leaked the
ref in the success case.
Fixes "ERROR: Bad of_node_put()" on bcm2835 in the -EPROBE_DEFER case.
Fixes: aa42240ab2 (PM / Domains: Add generic OF-based PM domain look-up)
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Cc: 3.18+ <stable@vger.kernel.org> # 3.18+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Support for the ACPI _CCA configuration object intended to tell
the OS whether or not a bus master device supports hardware
managed cache coherency and a new set of functions to allow
drivers to check the cache coherency support for devices in a
platform firmware interface agnostic way (Suravee Suthikulpanit,
Jeremy Linton).
- ACPI backlight quirks for ESPRIMO Mobile M9410 and Dell XPS L421X
(Aaron Lu, Hans de Goede).
- Fixes for the arm_big_little and s5pv210-cpufreq cpufreq drivers
(Jon Medhurst, Nicolas Pitre).
- kfree()-related fixup for the recently introduced CPPC cpufreq
frontend (Markus Elfring).
- intel_pstate fix reducing kernel log noise on systems where
P-states are managed by hardware (Prarit Bhargava).
- intel_pstate maintainers information update (Srinivas Pandruvada).
- cpufreq core optimization related to the handling of delayed work
items used by governors (Viresh Kumar).
- Locking fixes and cleanups of the Operating Performance Points
(OPP) framework (Viresh Kumar).
- Generic power domains framework cleanups (Lina Iyer).
- cpupower tool updates (Jacob Tanenbaum, Sriram Raghunathan,
Thomas Renninger).
- turbostat tool updates (Len Brown).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=XZiP
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management and ACPI updates from Rafael Wysocki:
"The only new feature in this batch is support for the ACPI _CCA device
configuration object, which it a pre-requisite for future ACPI PCI
support on ARM64, but should not affect the other architectures.
The rest is fixes and cleanups, mostly in cpufreq (including
intel_pstate), the Operating Performace Points (OPP) framework and
tools (cpupower and turbostat).
Specifics:
- Support for the ACPI _CCA configuration object intended to tell the
OS whether or not a bus master device supports hardware managed
cache coherency and a new set of functions to allow drivers to
check the cache coherency support for devices in a platform
firmware interface agnostic way (Suravee Suthikulpanit, Jeremy
Linton).
- ACPI backlight quirks for ESPRIMO Mobile M9410 and Dell XPS L421X
(Aaron Lu, Hans de Goede).
- Fixes for the arm_big_little and s5pv210-cpufreq cpufreq drivers
(Jon Medhurst, Nicolas Pitre).
- kfree()-related fixup for the recently introduced CPPC cpufreq
frontend (Markus Elfring).
- intel_pstate fix reducing kernel log noise on systems where
P-states are managed by hardware (Prarit Bhargava).
- intel_pstate maintainers information update (Srinivas Pandruvada).
- cpufreq core optimization related to the handling of delayed work
items used by governors (Viresh Kumar).
- Locking fixes and cleanups of the Operating Performance Points
(OPP) framework (Viresh Kumar).
- Generic power domains framework cleanups (Lina Iyer).
- cpupower tool updates (Jacob Tanenbaum, Sriram Raghunathan, Thomas
Renninger).
- turbostat tool updates (Len Brown)"
* tag 'pm+acpi-4.4-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
PCI: ACPI: Add support for PCI device DMA coherency
PCI: OF: Move of_pci_dma_configure() to pci_dma_configure()
of/pci: Fix pci_get_host_bridge_device leak
device property: ACPI: Remove unused DMA APIs
device property: ACPI: Make use of the new DMA Attribute APIs
device property: Adding DMA Attribute APIs for Generic Devices
ACPI: Adding DMA Attribute APIs for ACPI Device
device property: Introducing enum dev_dma_attr
ACPI: Honor ACPI _CCA attribute setting
cpufreq: CPPC: Delete an unnecessary check before the function call kfree()
PM / OPP: Add opp_rcu_lockdep_assert() to _find_device_opp()
PM / OPP: Hold dev_opp_list_lock for writers
PM / OPP: Protect updates to list_dev with mutex
PM / OPP: Propagate error properly from dev_pm_opp_set_sharing_cpus()
cpufreq: s5pv210-cpufreq: fix wrong do_div() usage
MAINTAINERS: update for intel P-state driver
Creating a common structure initialization pattern for struct option
cpupower: Enable disabled Cstates if they are below max latency
cpupower: Remove debug message when using cpupower idle-set -D switch
cpupower: cpupower monitor reports uninitialized values for offline cpus
...
support. The core framework is mostly unchanged this time
around, with only a couple patches to expose a clk provider
API and make getting clk parent names from DT more robust.
Driver updates:
- Support for clock controllers found on Broadcom Northstar
SoCs and bcm2835 SoC
- Support for Allwinner audio clocks
- A few cleanup patches for Tegra drivers and support for the
highest DFLL frequencies on Tegra124
- Samsung exynos7 fixes and improvements
- i.Mx SoC updates to add a few missing clocks and keep debug
uart clocks on during kernel intialization
- Some mediatek cleanups and support for more subsystem clocks
- Support for msm8916 gpu/audio clocks and qcom's GDSC power domain
controllers
- A new driver for the Silabs si514 clock chip
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=K6iN
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-20151104' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The majority of the changes are driver updates and new device support.
The core framework is mostly unchanged this time around, with only a
couple patches to expose a clk provider API and make getting clk
parent names from DT more robust.
Driver updates:
- Support for clock controllers found on Broadcom Northstar SoCs and
bcm2835 SoC
- Support for Allwinner audio clocks
- A few cleanup patches for Tegra drivers and support for the highest
DFLL frequencies on Tegra124
- Samsung exynos7 fixes and improvements
- i.Mx SoC updates to add a few missing clocks and keep debug uart
clocks on during kernel intialization
- Some mediatek cleanups and support for more subsystem clocks
- Support for msm8916 gpu/audio clocks and qcom's GDSC power domain
controllers
- A new driver for the Silabs si514 clock chip"
* tag 'clk-for-linus-20151104' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (143 commits)
clk: qcom: msm8960: Fix dsi1/2 halt bits
clk: lpc18xx-cgu: fix potential system hang when disabling unused clocks
clk: lpc18xx-ccu: fix potential system hang when disabling unused clocks
clk: Add clk_hw_is_enabled() for use by clk providers
clk: Add stubs for of_clk_*() APIs when CONFIG_OF=n
clk: versatile-icst: fix memory leak
clk: Remove clk_{register,unregister}_multiplier()
clk: iproc: define Broadcom NS2 iProc clock binding
clk: iproc: define Broadcom NSP iProc clock binding
clk: ns2: add clock support for Broadcom Northstar 2 SoC
clk: iproc: Separate status and control variables
clk: iproc: Split off dig_filter
clk: iproc: Add PLL base write function
clk: nsp: add clock support for Broadcom Northstar Plus SoC
clk: iproc: Add PWRCTRL support
clk: cygnus: Convert all macros to all caps
ARM: cygnus: fix link failures when CONFIG_COMMON_CLK_IPROC is disabled
clk: imx31: add missing of_node_put
clk: imx27: add missing of_node_put
clk: si5351: add missing of_node_put
...
In preparation for supporting IRQ-safe domains, allocate domain data
outside the domain locks. These functions are not called in an atomic
context, so we can always allocate memory using GFP_KERNEL. By
allocating memory before the locks, we can safely lock the domain using
spinlocks instead of mutexes.
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove check for driver of a device, for runtime PM. Device may be
suspended without an explicit driver. This check seems to be vestigial
and incorrect in the current context.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Measure latency does by itself contribute to an increased latency, thus we
should avoid it when it isn't needed.
By merging the latency measurements for the ->save_state() and the
->stop() callbacks, we get one measurement instead of two and we get one
value to store instead of two. Let's also apply the likewise change for
the ->start() and ->restore_state() callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lina Iyer <lina.iyer@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Measure latency does by itself contribute to an increased latency, thus we
should avoid it when it isn't needed.
Genpd measures latencies in the system PM phase for the ->start|stop()
callbacks and is thus affecting the system PM suspend/resume time.
Moreover these latencies are validated only at runtime PM suspend/resume.
To this reasoning, let's decide to leave these measurements out of the
system PM phase. There should be plenty of occasions during runtime PM to
perform these measurements anyway.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lina Iyer <lina.iyer@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is another step to get consistent names of functions in genpd. Let's
rename the internal *pm_genpd_poweron|poweroff() into
*genpd_poweron|poweroff().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Once genpd could be configured to be built with CONFIG_PM_RUNTIME unset
(nowadays CONFIG_PM), the pm_genpd_poweron() API served a purpose, since
it allowed users to power on a PM domain.
As such configuration no longer is supported, users shall solely rely on
using some of the runtime PM APIs to power on a PM domain.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As the last user of the pm_genpd_poweroff_unused() API has moved into
relying on genpd to deal with this internally from a late_initcall, let's
remove the API.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit ba2bbfbf63 ("PM / Domains: Remove intermediate states..") changed
the power off sequence (pm_genpd_poweroff()), which from locking point of
view means the genpd mutex is held throughout the sequence.
The above change means the in_progress counter can't be updated while
pm_genpd_poweroff() is executing, which allows us to remove the counter.
Instead we inform pm_genpd_poweroff() via a bool parameter, to indicate
whether we call it from the scheduled work or from the ->runtime_suspend()
callback, since that all that matters.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Export these symbols so they can be used in loadable kernel
modules.
Cc: Rob Clark <robdclark@gmail.com>
Cc: Rajendra Nayak <rnayak@codeaurora.org>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The power domains code allows to tie a cpuidle state with a power domain.
Preventing the cpuidle framework to enter a specific idle state by disabling
from the power domain framework is a good idea. Unfortunately, the current
implementation has some gaps with a SMP system and a complex cpuidle
implementation. Enabling a power domain wakes up all the cpus even if a cpu
does not belong to the power domain.
There is some work to do a logical representation with the power domains of
the hardware dependencies (eg. a cpu belongs to a power domains, these power
domains belong to a higher power domain for a cluster, etc ...). A new code
relying on the genpd hierarchy to disable the idle states would make more
sense.
As the unique user of this code has been removed, let's wipe out this code
to prevent new user and to have a clean place to put a new implementation.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As all users of the named based APIs now have converted to the non-named
based APIs, the time has come to remove them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function pm_genpd_remove_subdomain() removes a subdomain from a
generic PM domain, however, it does not check if the subdomain has any
slave domains or device attached before doing so. Therefore, add a test
to verify that the subdomain does not have any slave domains associated
or any device attached before removing.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While powering up a genpd, its domain masters are first being powered up.
In the error path of __pm_genpd_poweron(), we didn't care to try power off
these domain masters. Let's deal with that to avoid leaving unused PM
domains powered.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function genpd_dev_pm_detach() detaches a device from a PM domain,
however, in the description, the "dev" argument for the function is
described as the device to "attach" instead of "detach". Correct this.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Export symbol pm_genpd_init so it can be used in loadable
kernel modules
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
"domain": header is indented by 4, data by 0 spaces => 0 spaces
"/device": header is indented by 11, data by 4 spaces => 4 spaces
"slaves": header is indented by 47, data by 49 spaces => 48 spaces
Ruler:
1234567890123456789012345678901234567890123456789012345678901234567890
Before:
domain status slaves
/device runtime status
----------------------------------------------------------------------
a3sp on a2us
/devices/platform/e60b0000.i2c suspended
After:
domain status slaves
/device runtime status
----------------------------------------------------------------------
a3sp on a2us
/devices/platform/e60b0000.i2c suspended
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When a device is probed, the function dev_pm_domain_attach() is called
to see if there is a power-domain that is associated with the device and
needs to be turned on. If dev_pm_domain_attach() does not return
-EPROBE_DEFER then the device will be probed.
For devices using genpd, dev_pm_domain_attach() will call
genpd_dev_pm_attach(). If genpd_dev_pm_attach() does not find a power
domain associated with the device then it returns an error code not
equal to -EPROBE_DEFER to allow the device to be probed. However, if
genpd_dev_pm_attach() does find a power-domain that is associated with
the device, then it does not return -EPROBE_DEFER on failure and hence
the device will still be probed. Furthermore, genpd_dev_pm_attach() does
not check the error code returned by pm_genpd_poweron() to see if the
power-domain was turned on successfully.
Fix this by checking the return code from pm_genpd_poweron() and
returning -EPROBE_DEFER from genpd_dev_pm_attach on failure, if there
is a power-domain associated with the device.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Genpd's ->runtime_suspend() (assigned to pm_genpd_runtime_suspend())
doesn't immediately walk the hierarchy of ->runtime_suspend() callbacks.
Instead, pm_genpd_runtime_suspend() calls pm_genpd_poweroff() which
postpones that until *all* the devices in the genpd are runtime suspended.
When pm_genpd_poweroff() discovers that the last device in the genpd is
about to be runtime suspended, it calls __pm_genpd_save_device() for *all*
the devices in the genpd sequentially. Furthermore,
__pm_genpd_save_device() invokes the ->start() callback, walks the
hierarchy of the ->runtime_suspend() callbacks and invokes the ->stop()
callback. This causes a "thundering herd" problem.
Let's address this issue by having pm_genpd_runtime_suspend() immediately
walk the hierarchy of the ->runtime_suspend() callbacks, instead of
postponing that to the power off sequence via pm_genpd_poweroff(). If the
selected ->runtime_suspend() callback doesn't return an error code, call
pm_genpd_poweroff() to see if it's feasible to also power off the PM
domain.
Adopting this change enables us to simplify parts of the code in genpd,
for example the locking mechanism. Additionally, it gives some positive
side effects, as described below.
i)
One device's ->runtime_resume() latency is no longer affected by other
devices' latencies in a genpd.
The complexity genpd has to support the option to abort the power off
sequence suffers from latency issues. More precisely, a device that is
requested to be runtime resumed, may end up waiting for
__pm_genpd_save_device() to complete its operations for *another* device.
That's because pm_genpd_poweroff() can't confirm an abort request while it
waits for __pm_genpd_save_device() to return.
As this patch removes the intermediate states in pm_genpd_poweroff() while
powering off the PM domain, we no longer need the ability to abort that
sequence.
ii)
Make pm_runtime[_status]_suspended() reliable when used with genpd.
Until the last device in a genpd becomes idle, pm_genpd_runtime_suspend()
will return 0 without actually walking the hierarchy of the
->runtime_suspend() callbacks. However, by returning 0 the runtime PM core
considers the device as runtime_suspended, so
pm_runtime[_status]_suspended() will return true, even though the device
isn't (yet) runtime suspended.
After this patch, since pm_genpd_runtime_suspend() immediately walks the
hierarchy of the ->runtime_suspend() callbacks,
pm_runtime[_status]_suspended() will accurately reflect the status of the
device.
iii)
Enable fine-grained PM through runtime PM callbacks in drivers/subsystems.
There are currently cases were drivers/subsystems implements runtime PM
callbacks to deploy fine-grained PM (e.g. gate clocks, move pinctrl to
power-save state, etc.). While using the genpd, pm_genpd_runtime_suspend()
postpones invoking these callbacks until *all* the devices in the genpd
are runtime suspended. In essence, one runtime resumed device prevents
fine-grained PM for other devices within the same genpd.
After this patch, since pm_genpd_runtime_suspend() immediately walks the
hierarchy of the ->runtime_suspend() callbacks, fine-grained PM is enabled
throughout all the levels of runtime PM callbacks.
iiii)
Enable fine-grained PM for IRQ safe devices
Per the definition for an IRQ safe device, its runtime PM callbacks must
be able to execute in atomic context. In the path while genpd walks the
hierarchy of the ->runtime_suspend() callbacks for the device, it uses a
mutex. Therefore, genpd prevents that path to be executed for IRQ safe
devices.
As this patch changes pm_genpd_runtime_suspend() to immediately walk the
hierarchy of the ->runtime_suspend() callbacks and without needing to use
a mutex, fine-grained PM is enabled throughout all the levels of runtime
PM callbacks for IRQ safe devices.
Unfortunately this patch also comes with a drawback, as described in the
summary below.
Driver's/subsystem's runtime PM callbacks may be invoked even when the
genpd hasn't actually powered off the PM domain, potentially introducing
unnecessary latency.
However, in most cases, saving/restoring register contexts for devices are
typically fast operations or can be optimized in device specific ways
(e.g. shadow copies of register contents in memory, device-specific checks
to see if context has been lost before restoring context, etc.).
Still, in some cases the driver/subsystem may suffer from latency if
runtime PM is used in a very fine-grained manner (e.g. for each IO request
or xfer). To prevent that extra overhead, the driver/subsystem may deploy
the runtime PM autosuspend feature.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If pm_genpd_{add,remove}_device() keeps on failing with -EAGAIN, we end
up with an infinite loop in genpd_dev_pm_{at,de}tach().
This may happen due to a genpd.prepared_count imbalance. This is a bug
elsewhere, but it will result in a system lock up, possibly during
reboot of an otherwise functioning system.
To avoid this, put a limit on the maximum number of loop iterations,
using an exponential back-off mechanism. If the limit is reached, the
operation will just fail. An error message is already printed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PM Domain code uses ktime_get() to perform various latency
measurements. However, if ktime_get() is called while timekeeping is
suspended, the following warning is printed:
WARNING: CPU: 0 PID: 1340 at kernel/time/timekeeping.c:576 ktime_get+0x3
This happens when resuming the PM Domain that contains the clock events
source, which calls pm_genpd_syscore_poweron(). Chain of operations is:
timekeeping_resume()
{
clockevents_resume()
sh_cmt_clock_event_resume()
pm_genpd_syscore_poweron()
pm_genpd_sync_poweron()
genpd_syscore_switch()
genpd_power_on()
ktime_get(), but timekeeping_suspended == 1
...
timekeeping_suspended = 0;
}
Fix this by adding a "timed" parameter to genpd_power_{on,off}() and
pm_genpd_sync_power{off,on}(), to indicate whether latency measurements
are allowed. This parameter is passed as false in
genpd_syscore_switch() (i.e. during syscore suspend/resume), and true in
all other cases.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pm_genpd_remove_device() tries hard to validate the generic PM domain
passed to it, but the validation is not complete.
dev->pm_domain contains a struct dev_pm_domain, which is the "base
class" of generic PM domains. Other users of dev_pm_domains include
stuff like vga_switheroo. Hence, a device could have a generic PM
domain or a vga_switcheroo PM domain in dev->pm_domain.
We need ot be certain that the PM domain is actually valid before we
try to remove it. We can do this easily as we have a way to get the
current validated generic PM domain for a struct device. This must
match the generic PM domain being requested for removal.
Convert the code to use this alternative validation method instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PM domain code contains two methods to get the generic PM domain
for a struct device. One is dev_to_genpd() which is only safe when
we know for certain that the device has a generic PM domain attached.
The other is coded into genpd_dev_pm_detach() which ensures that the
PM domain in the struct device is a generic PM domain (and so is safer).
This commit factors out the safer version, documents it, and hides the
unsafe dev_to_genpd().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM domains are rather noisy; scheduling behaviour can cause callbacks
to take longer, which causes them to spit out a warning-level message
each time a callback takes a little longer than the previous time.
There really isn't a need for this, except when debugging.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Buses which currently supports attaching devices to their PM domains,
will invoke the dev_pm_domain_attach() API from their ->probe()
callbacks. During the attach procedure, genpd power up the PM domain.
In those scenarios where the bus/driver don't need to access its device
during probe, it may leave it in runtime PM suspended state since
that's also the default state. In that way, no notifications through
the runtime PM callbacks will reach the PM domain during probe.
For genpd, the consequence from the above scenario means the PM domain
will remain powered. Therefore, implement the struct dev_pm_domain's
->sync() callback, which is invoked from driver core after the
bus/driver has probed the device. It allows genpd to power off the PM
domain if it's unused.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ Ulf: Updated patch according to updates in driver core ]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To keep consisitency with the rest of the file, use 'genpd' as the
name of the 'struct generic_pm_domain' pointer instead of 'gpd'.
This is just a rename, no functional changes.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The optional genpd's ->attach_dev() callback is invoked from
__pm_genpd_add_device(). Let's add error handling from the response
from this callback and propagate the error code.
When __pm_genpd_add_device() is invoked through the generic OF-based PM
domain look-up path, the device is being probed. Returning an error
will mean the device won't be attached to its PM domain. Errors of
-EPROBE_DEFER get special treatment and is propagated to the driver
core.
Therefore this change also enables the ->attach_dev() callback to
be able to request for a deferred probe sequence.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move the initialization of the struct generic_pm_domain_data into
genpd_alloc_dev_data(), including the assignment of the device's
->pm_domain() callback. Make corresponding changes to
genpd_free_dev_data().
These changes will make the related code more readable. It will also
decrease the critical regions for where genpd's mutex is being held and
for where the device's power related spinlock is being held.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The error path in __pm_genpd_add_device() didn't decrease the reference
to the struct pm_subsys_data.
Let's move the calls to dev_pm_get|put_subsys_data() into
genpd_alloc|free_dev_data() to fix this issue and thus prevent a
potential memory leakage.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While adding devices to their PM domains, dev_pm_qos_add_notifier() was
invoked while allocating the generic_pm_domain_data for the device.
Since the generic_pm_domain_data's device pointer will be assigned
after allocation, the ->genpd_dev_pm_qos_notifier() callback could be
called prior having a valid pointer to the device. Similar scenario
existed while removing a device from a genpd.
To cope with these scenarios a mutex was used to protect the pointer to
the device.
By re-order the sequence for when dev_pm_qos_add|remove_notifier() are
invoked, we make sure the ->genpd_dev_pm_qos_notifier() callback are
always called with a valid device pointer available.
In this way, we eliminate the need for protecting the pointer and thus
we can remove the mutex from the struct generic_pm_domain_data.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When adding a device to a genpd, we no longer need to walk genpd's list
of existing devices to verify it hasn't already been added.
Instead we can now rely on the verification of not allowing existing
generic_pm_domain_data for a device, since that has the same meaning.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When adding a device to a genpd, a struct generic_pm_domain_data is
allocated per device.
Verify that there are no existing generic_pm_domain_data for the device
we are about to add, since that tells us it has already been added to a
genpd.
When genpd supported PM domain device callbacks, this was a valid
scenario. Now it isn't so let's return an error code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The reference counting was needed when genpd supported PM domain device
callbacks. Since this option has been removed, let's also remove the
reference counting of the struct generic_pm_domain_data.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In a step to get consistent names of functions in genpd, rename
the internal __pm_genpd_alloc|free_dev_data() into
gendp_alloc|free_dev_data().
As discussed on the linux-pm list, let's move towards the following
name rules:
Internal functions:
genpd_*
_genpd_*
__genpd_*
External functions:
pm_genpd_*
_pm_genpd_*
__pm_genpd_*
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are currently no users of this API, let's remove it.
Additionally, if such feature would be needed future wise, a better
option is likely use pm_runtime_set_active|suspended() in some form.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-domains:
PM / Domains: Export of_genpd_get_from_provider function
* powercap:
powercap / RAPL: add IDs for future Xeon CPUs
* pm-tools:
tools / cpupower: Fix no idle state information return value
tools / cpupower: Correctly detect if running as root
This function looks up a PM domain form the provider. This will be
useful to add parent/child domain relationship from the SoC specific
code. The caller of the function must make sure that PM domain provider
is already registered.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM or even may be dropped entirely in some cases.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the PM core code.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It's quite common for PM domains to use PM clocks. Typically from SOC
specific code, the per device PM clock list is created and
pm_clk_suspend|resume() are invoked to handle clock gating/ungating.
A step towards consolidation is to integrate PM clock support into
genpd, which is what this patch does.
In this initial step, the calls to the pm_clk_suspend|resume() are
handled within genpd, but the per device PM clock list still needs to
be created from SOC specific code. It seems reasonable to have gendp to
handle that as well, but that left to future patches to address.
It's not every users of genpd that are keen on using PM clocks, thus we
need to provide this a configuration option for genpd. Therefore let's
add flag field in the genpd struct to keep this information and define
a new GENDP_FLAG_PM_CLK bit for it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Vast amount of platform drivers which enables runtime PM, don't invoke
a pm_runtime_get_sync() while probing their devices.
Instead, once they have turned on their PM resourses during ->probe()
and are ready to handle I/O, these invokes pm_runtime_set_active() to
synchronize its state towards the runtime PM core.
From the runtime PM point of view this behavior is perfectly acceptable,
but we encounter probe failures if their corresponding devices resides
in the generic PM domain. The issues are observed for those devices,
which requires its PM domain to stay powered during ->probe() since
that's not being controlled.
While using the generic OF-based PM domain look-up, a device's PM
domain will be attached during the probe sequence. For this path, let's
fix the probe failures, by simply power on the PM domain right after
when it's been attached to the device.
The generic PM domain stays powered until all of its devices becomes
runtime PM enabled and runtime PM suspended.
The old SOCs which makes use of the generic PM domain but don't use the
generic OF-based PM domain look-up, will not be affected from this
change.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
PM domains are powered on/off from various places. Some callers do
latency measurements, others don't. Consolidate using two helper
functions, which always measure the latencies, and update the stored
latencies when needed.
Other minor changes:
- Use pr_warn() instead of pr_warning(),
- There's no need to check genpd->name, %s handles NULL pointers fine,
- Make the warning format strings identical, to save memory.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PM domain pointed to by the genpd parameter is never modified.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The initial state of the device's need_restore flag should'nt depend on
the current state of the PM domain. For example it should be perfectly
valid to attach an inactive device to a powered PM domain.
The pm_genpd_dev_need_restore() API allow us to update the need_restore
flag to somewhat cope with such scenarios. Typically that should have
been done from drivers/buses ->probe() since it's those that put the
requirements on the value of the need_restore flag.
Until recently, the Exynos SOCs were the only user of the
pm_genpd_dev_need_restore() API, though invoking it from a centralized
location while adding devices to their PM domains.
Due to that Exynos now have swithed to the generic OF-based PM domain
look-up, it's no longer possible to invoke the API from a centralized
location. The reason is because devices are now added to their PM
domains during the probe sequence.
Commit "ARM: exynos: Move to generic PM domain DT bindings"
did the switch for Exynos to the generic OF-based PM domain look-up,
but it also removed the call to pm_genpd_dev_need_restore(). This
caused a regression for some of the Exynos drivers.
To handle things more properly in the generic PM domain, let's change
the default initial value of the need_restore flag to reflect that the
state is unknown. As soon as some of the runtime PM callbacks gets
invoked, update the initial value accordingly.
Moreover, since the generic PM domain is verifying that all devices
are both runtime PM enabled and suspended, using pm_runtime_suspended()
while pm_genpd_poweroff() is invoked from the scheduled work, we can be
sure of that the PM domain won't be powering off while having active
devices.
Do note that, the generic PM domain can still only know about active
devices which has been activated through invoking its runtime PM resume
callback. In other words, buses/drivers using pm_runtime_set_active()
during ->probe() will still suffer from a race condition, potentially
probing a device without having its PM domain being powered. That issue
will have to be solved using a different approach.
This a log from the boot regression for Exynos5, which is being fixed in
this patch.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 308 at ../drivers/clk/clk.c:851 clk_disable+0x24/0x30()
Modules linked in:
CPU: 0 PID: 308 Comm: kworker/0:1 Not tainted 3.18.0-rc3-00569-gbd9449f-dirty #10
Workqueue: pm pm_runtime_work
[<c0013c64>] (unwind_backtrace) from [<c0010dec>] (show_stack+0x10/0x14)
[<c0010dec>] (show_stack) from [<c03ee4cc>] (dump_stack+0x70/0xbc)
[<c03ee4cc>] (dump_stack) from [<c0020d34>] (warn_slowpath_common+0x64/0x88)
[<c0020d34>] (warn_slowpath_common) from [<c0020d74>] (warn_slowpath_null+0x1c/0x24)
[<c0020d74>] (warn_slowpath_null) from [<c03107b0>] (clk_disable+0x24/0x30)
[<c03107b0>] (clk_disable) from [<c02cc834>] (gsc_runtime_suspend+0x128/0x160)
[<c02cc834>] (gsc_runtime_suspend) from [<c0249024>] (pm_generic_runtime_suspend+0x2c/0x38)
[<c0249024>] (pm_generic_runtime_suspend) from [<c024f44c>] (pm_genpd_default_save_state+0x2c/0x8c)
[<c024f44c>] (pm_genpd_default_save_state) from [<c024ff2c>] (pm_genpd_poweroff+0x224/0x3ec)
[<c024ff2c>] (pm_genpd_poweroff) from [<c02501b4>] (pm_genpd_runtime_suspend+0x9c/0xcc)
[<c02501b4>] (pm_genpd_runtime_suspend) from [<c024a4f8>] (__rpm_callback+0x2c/0x60)
[<c024a4f8>] (__rpm_callback) from [<c024a54c>] (rpm_callback+0x20/0x74)
[<c024a54c>] (rpm_callback) from [<c024a930>] (rpm_suspend+0xd4/0x43c)
[<c024a930>] (rpm_suspend) from [<c024bbcc>] (pm_runtime_work+0x80/0x90)
[<c024bbcc>] (pm_runtime_work) from [<c0032a9c>] (process_one_work+0x12c/0x314)
[<c0032a9c>] (process_one_work) from [<c0032cf4>] (worker_thread+0x3c/0x4b0)
[<c0032cf4>] (worker_thread) from [<c003747c>] (kthread+0xcc/0xe8)
[<c003747c>] (kthread) from [<c000e738>] (ret_from_fork+0x14/0x3c)
---[ end trace 40cd58bcd6988f12 ]---
Fixes: a4a8c2c496 (ARM: exynos: Move to generic PM domain DT bindings)
Reported-and-tested0by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tomeu Vizoso