A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.
In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.
When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.
Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).
Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.
When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.
In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The zone allocator is a mechanism which manages a few mlx4_bitmaps.
When allocating a resource, the user indicates the desired zone of
which this resource will be allocated from. If possible, the resource
will be allocated from this zone. Otherwise, the resource will be
allocated from a less-than, equal-to, higher-than priority zone,
according to the desired zone's properties with that respective
allocation order.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.
The current Ethernet driver code reserves a Tx QP range with 256b alignment.
This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we've fired all our completion callbacks straight from our ISR.
Some of those callbacks were lightweight (for example, mlx4_en's and
IPoIB napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over those
events could be so long, that we'll get into a hard lockup by the system
watchdog.
In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive completion
event to a per-EQ list and schedule a tasklet. In the tasklet context
we loop over all the CQs in the list and invoke the user callback.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactoring mlx4_cmd_init and mlx4_cmd_cleanup such that partial init
and cleanup are possible. After this refactoring, calling mlx4_cmd_init
several times is safe.
This is necessary in the VF init flow when mlx4_init_hca returns -EACCESS,
we need to issue cleanup and re-attempt to call it with the slave flag.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to issue CONFIG_DEV "get" firmware command.
This command is used in order to obtain certain parameters used for
supporting various RX checksumming options and vxlan UDP port.
The GET operation is allowed for VFs too.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added wrapper to the ACCESS_REG command for handling guest HW
registers access, preventing write operations, but do allow reads.
This will prevent SRIOV guests to change port PTYS configuration,
such as speed/advertised link modes.
Fixes: adbc7ac5c1 ('net/mlx4_core: Introduce ACCESS_REG CMD [...]')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is intended for archs having cache line larger then 64B.
Since our CQE/EQEs are generally 64B in those systems, HW will write
twice to the same cache line consecutively, causing pipe locks due to
he hazard prevention mechanism. For elements in a cyclic buffer, writes
are consecutive, so entries smaller than a cache line should be
avoided, especially if they are written at a high rate.
Reduce consecutive writes to same cache line in CQs/EQs, by allowing the
driver to increase the distance between entries so that each will reside
in a different cache line. Until the introduction of this feature, there
were two types of CQE/EQE:
1. 32B stride and context in the [0-31] segment
2. 64B stride and context in the [32-63] segment
This feature introduces two additional types:
3. 128B stride and context in the [0-31] segment (128B cache line)
4. 256B stride and context in the [0-31] segment (256B cache line)
Modify the mlx4_core driver to query the device for the CQE/EQE cache
line stride capability and to enable that capability when the host
cache line size is larger than 64 bytes (supported cache lines are
128B and 256B).
The mlx4 IB driver and libmlx4 need not be aware of this change. The PF
context behaviour is changed to require this change in VF drivers
running on such archs.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wOm0
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
"Main set of InfiniBand/RDMA updates for 3.17 merge window:
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes..."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (52 commits)
IB/srp: Fix return value check in srp_init_module()
RDMA/ocrdma: report asic-id in query device
RDMA/ocrdma: Update sli data structure for endianness
RDMA/ocrdma: Obtain SL from device structure
RDMA/uapi: Include socket.h in rdma_user_cm.h
IB/srpt: Handle GID change events
IB/mlx5: Use ARRAY_SIZE instead of sizeof/sizeof[0]
IB/mlx4: Use ARRAY_SIZE instead of sizeof/sizeof[0]
RDMA/amso1100: Check for integer overflow in c2_alloc_cq_buf()
IPoIB: Remove unnecessary test for NULL before debugfs_remove()
IB/mad: Add user space RMPP support
IB/mad: add new ioctl to ABI to support new registration options
IB/mad: Add dev_notice messages for various umad/mad registration failures
IB/mad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid multicast join attempts with invalid P_key
IB/umad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid flushing the workqueue from worker context
IB/ipoib: Use P_Key change event instead of P_Key polling mechanism
IB/ipath: Add P_Key change event support
mlx4_core: Add support for secure-host and SMP firewall
...
Secure-host is the general term for the capability of a device
to protect itself and the subnet from malicious host software.
This is achieved by:
1. Not allowing un-trusted entities to access device configuration
registers, directly (through pci_cr or pci_conf) and indirectly
(through MADs).
2. Hiding M_Key from untrusted entities.
3. Preventing the modification of GUID0 by un-trusted entities
4. Not allowing drivers on untrusted hosts to receive nor to transmit
packets over QP0 (SMP Firewall).
The secure-host capability depends on firmware handling all QP0
packets, and not passing these packets up to the driver. Any information
required by the driver for proper operation (e.g., SM lid) is passed
via events generated by the firmware while processing QP0 MADs.
Driver support mainly requires using the MAD_DEMUX FW command at startup,
where the feature is enabled/disabled through a procedure described in
the Mellanox HCA tools package.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
[ Fix error path in mlx4_setup_hca to go to err_mcg_table_free. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add few helper functions to support a mechanism of getting an MPT,
modifying it and updating the HCA with the modified object.
The code takes 2 paths, one for directly changing the MPT (and
sometimes its related MTTs) and another one which queries the MPT and
updates the HCA via fw command SW2HW_MPT. The first path is used in
native mode; the second path is slower and is used only in SRIOV.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In 40GE we can't use the default bw units for set ratelimit (100 Mbps)
since the max is 255*100 Mbps = 25 Gbps (not suited for 40GE), thus we need 1 Gbps units.
But for 10GE 1 Gbps units might be too bruit so we use the following solution.
For user set ratelimit <= 25 Gbps:
use 100 Mbps units * user_ratelimit (* 10).
For user set ratelimit > 25 Gbps:
use 1 Gbps units * user_ratelimit.
For user set unlimited ratelimit (0 Gbps):
use 1 Gbps units * MAX_RATELIMIT_DEFAULT (57)
Note: any value > 58 will damage the FW ratelimit computation, so we allow
a max and any higher value will be pulled down to 57.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.
2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
Benniston.
3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
Mork.
4) BPF now has a "random" opcode, from Chema Gonzalez.
5) Add more BPF documentation and improve test framework, from Daniel
Borkmann.
6) Support TCP fastopen over ipv6, from Daniel Lee.
7) Add software TSO helper functions and use them to support software
TSO in mvneta and mv643xx_eth drivers. From Ezequiel Garcia.
8) Support software TSO in fec driver too, from Nimrod Andy.
9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.
10) Handle broadcasts more gracefully over macvlan when there are large
numbers of interfaces configured, from Herbert Xu.
11) Allow more control over fwmark used for non-socket based responses,
from Lorenzo Colitti.
12) Do TCP congestion window limiting based upon measurements, from Neal
Cardwell.
13) Support busy polling in SCTP, from Neal Horman.
14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.
15) Bridge promisc mode handling improvements from Vlad Yasevich.
16) Don't use inetpeer entries to implement ID generation any more, it
performs poorly, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
tcp: fixing TLP's FIN recovery
net: fec: Add software TSO support
net: fec: Add Scatter/gather support
net: fec: Increase buffer descriptor entry number
net: fec: Factorize feature setting
net: fec: Enable IP header hardware checksum
net: fec: Factorize the .xmit transmit function
bridge: fix compile error when compiling without IPv6 support
bridge: fix smatch warning / potential null pointer dereference
via-rhine: fix full-duplex with autoneg disable
bnx2x: Enlarge the dorq threshold for VFs
bnx2x: Check for UNDI in uncommon branch
bnx2x: Fix 1G-baseT link
bnx2x: Fix link for KR with swapped polarity lane
sctp: Fix sk_ack_backlog wrap-around problem
net/core: Add VF link state control policy
net/fsl: xgmac_mdio is dependent on OF_MDIO
net/fsl: Make xgmac_mdio read error message useful
net_sched: drr: warn when qdisc is not work conserving
...
- Add iWARP port mapper to avoid conflicts between RDMA and normal
stack TCP connections.
- Fixes for i386 / x86-64 structure padding differences (ABI
compatibility for 32-on-64) from Yann Droneaud.
- A pile of SRP initiator fixes from Bart Van Assche.
- Fixes for a writeback / memory allocation deadlock with NFS over
IPoIB connected mode from Jiri Kosina.
- The usual fixes and cleanups to mlx4, mlx5, cxgb4 and other
low-level drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Wcdc
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull main InfiniBand/RDMA updates from Roland Dreier:
- add iWARP port mapper to avoid conflicts between RDMA and normal
stack TCP connections.
- fixes for i386 / x86-64 structure padding differences (ABI
compatibility for 32-on-64) from Yann Droneaud.
- a pile of SRP initiator fixes from Bart Van Assche.
- fixes for a writeback / memory allocation deadlock with NFS over
IPoIB connected mode from Jiri Kosina.
- the usual fixes and cleanups to mlx4, mlx5, cxgb4 and other low-level
drivers.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (61 commits)
RDMA/cxgb4: Add support for iWARP Port Mapper user space service
RDMA/nes: Add support for iWARP Port Mapper user space service
RDMA/core: Add support for iWARP Port Mapper user space service
IB/mlx4: Fix gfp passing in create_qp_common()
IB/umad: Fix use-after-free on close
IB/core: Fix kobject leak on device register error flow
RDMA/cxgb4: add missing padding at end of struct c4iw_alloc_ucontext_resp
mlx4_core: Fix GFP flags parameters to be gfp_t
IB/core: Fix port kobject deletion during error flow
IB/core: Remove unneeded kobject_get/put calls
IB/core: Fix sparse warnings about redeclared functions
IB/mad: Fix sparse warning about gfp_t use
IB/mlx4: Implement IB_QP_CREATE_USE_GFP_NOIO
IB: Add a QP creation flag to use GFP_NOIO allocations
IB: Return error for unsupported QP creation flags
IB: Allow build of hw/ and ulp/ subdirectories independently
mlx4_core: Move handling of MLX4_QP_ST_MLX to proper switch statement
RDMA/cxgb4: Add missing padding at end of struct c4iw_create_cq_resp
IB/srp: Avoid problems if a header uses pr_fmt
IB/umad: Fix error handling
...
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify the various routines used to allocate memory resources which
serve QPs in mlx4 to get an input GFP directive. Have the Ethernet
driver to use GFP_KERNEL in it's QP allocations as done prior to this
commit, and the IB driver to use GFP_NOIO when the IB verbs
IB_QP_CREATE_USE_GFP_NOIO QP creation flag is provided.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Reset the GIDs assigned to a VF in the port RoCE GID table when
that guest goes down (either crashes or goes down cleanly).
As part of this fix, we refactor the RoCE gid table driver copy,
moving it to the mlx4_port_info structure (together with the MAC
and VLAN tables).
As with the MAC and VLAN tables, we now use a mutex per port
for the GID table so that modifying the driver copy and
modifying the firmware copy of a port GID table becomes an
atomic operation (thus avoiding driver-copy/FW-copy mismatches).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the infrastructure for enabling selected VFs to
operate SMI (QP0) MADs without restriction.
Additionally, for these enabled VFs, their QP0 proxy and tunnel QPs
are MLX QPs. As such, they operate over VL15. Therefore, they are
not affected by "credit" problems or changes in the VLArb table (which
may shut down VL0).
Non-enabled VFs may only create UD proxy QP0 qps (which are forced by
the hypervisor to send packets using the q-key it assigns and places
in the qp-context). Thus, non-enabled VFs will not pose a security
risk. The hypervisor discards any privileged MADs it receives from
these non-enabled VFs.
By default, all VFs are NOT enabled, and must explicitly be enabled
by the administrator.
The sysfs interface which operates the VF enablement infrastructure
is provided in the next commit.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds UPDATE_QP SRIOV wrapper support.
The mechanism is a general one, but currently only source MAC
index changes are allowed for VFs.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a more current logging style.
o Coalesce formats
o Add missing spaces for coalesced formats
o Align arguments for modified formats
o Add missing newlines for some logging messages
o Use DRV_NAME as part of format instead of %s, DRV_NAME to
reduce overall text.
o Use ..., ##__VA_ARGS__ instead of args... in macros
o Correct a few format typos
o Use a single line message where appropriate
Signed-off-by: Joe Perches <joe@perches.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_match_id() just match the static pci_device_id, which may return NULL if
someone binds the driver to a device manually using
/sys/bus/pci/drivers/.../new_id.
This patch wrap up a helper function __mlx4_remove_one() which does the tear
down function but preserve the drv_data. Functions like
mlx4_pci_err_detected() and mlx4_restart_one() will call this one with out
releasing drvdata.
Fixes: 97a5221 "net/mlx4_core: pass pci_device_id.driver_data to __mlx4_init_one during reset".
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Amir Vadai <amirv@mellanox.com>
CC: Jack Morgenstein <jackm@dev.mellanox.co.il>
CC: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Acked-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VF issues a firmware command which is disallowed for them, the PF
rerturns -EPERM from that command wrapper. Move to use one such wrapper
instance, instead of repeating the same code on such commands.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
In wrapped commands, we need to verify and convert
the slave's port into the real physical port.
Furthermore, when sending the response back to the slave,
a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
The slave assumes that sqpn is used for QP1 communication.
If the slave is assigned to a port != (first port), we need
to adjust the sqpn that will direct its QP1 packets into the
correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
In B0 steering, gid[5] contains the port. It needs
to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
When a slave queries the hardware, it needs to view only
the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
The QP port is encoded in the sched_qp, thus in modify_qp we need
to encode the correct port in sched_qp.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the following utils:
1. Convert slave_id -> VF
2. Get the active ports by slave_id
3. Convert slave's port to real port
4. Get the slave's port from real port
5. Get all slaves that uses the i'th real port
6. Get all slaves that uses the i'th real port exclusively
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GIDs are statically distributed, as follows:
PF: gets 16 GIDs
VFs: Remaining GIDS are divided evenly between VFs activated by the driver.
If the division is not even, lower-numbered VFs get an extra GID.
For an IB interface, the number of gids per guest remains as before: one gid per guest.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This requires the following modifications:
1. Fix build_mlx4_header to properly fill in the ETH fields
2. Adjust mux and demux QP1 flow to support RoCE.
This commit still assumes only one GID per slave for RoCE.
The commit enabling multiple GIDs is a subsequent commit, and
is done separately because of its complexity.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) BPF debugger and asm tool by Daniel Borkmann.
2) Speed up create/bind in AF_PACKET, also from Daniel Borkmann.
3) Correct reciprocal_divide and update users, from Hannes Frederic
Sowa and Daniel Borkmann.
4) Currently we only have a "set" operation for the hw timestamp socket
ioctl, add a "get" operation to match. From Ben Hutchings.
5) Add better trace events for debugging driver datapath problems, also
from Ben Hutchings.
6) Implement auto corking in TCP, from Eric Dumazet. Basically, if we
have a small send and a previous packet is already in the qdisc or
device queue, defer until TX completion or we get more data.
7) Allow userspace to manage ipv6 temporary addresses, from Jiri Pirko.
8) Add a qdisc bypass option for AF_PACKET sockets, from Daniel
Borkmann.
9) Share IP header compression code between Bluetooth and IEEE802154
layers, from Jukka Rissanen.
10) Fix ipv6 router reachability probing, from Jiri Benc.
11) Allow packets to be captured on macvtap devices, from Vlad Yasevich.
12) Support tunneling in GRO layer, from Jerry Chu.
13) Allow bonding to be configured fully using netlink, from Scott
Feldman.
14) Allow AF_PACKET users to obtain the VLAN TPID, just like they can
already get the TCI. From Atzm Watanabe.
15) New "Heavy Hitter" qdisc, from Terry Lam.
16) Significantly improve the IPSEC support in pktgen, from Fan Du.
17) Allow ipv4 tunnels to cache routes, just like sockets. From Tom
Herbert.
18) Add Proportional Integral Enhanced packet scheduler, from Vijay
Subramanian.
19) Allow openvswitch to mmap'd netlink, from Thomas Graf.
20) Key TCP metrics blobs also by source address, not just destination
address. From Christoph Paasch.
21) Support 10G in generic phylib. From Andy Fleming.
22) Try to short-circuit GRO flow compares using device provided RX
hash, if provided. From Tom Herbert.
The wireless and netfilter folks have been busy little bees too.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2064 commits)
net/cxgb4: Fix referencing freed adapter
ipv6: reallocate addrconf router for ipv6 address when lo device up
fib_frontend: fix possible NULL pointer dereference
rtnetlink: remove IFLA_BOND_SLAVE definition
rtnetlink: remove check for fill_slave_info in rtnl_have_link_slave_info
qlcnic: update version to 5.3.55
qlcnic: Enhance logic to calculate msix vectors.
qlcnic: Refactor interrupt coalescing code for all adapters.
qlcnic: Update poll controller code path
qlcnic: Interrupt code cleanup
qlcnic: Enhance Tx timeout debugging.
qlcnic: Use bool for rx_mac_learn.
bonding: fix u64 division
rtnetlink: add missing IFLA_BOND_AD_INFO_UNSPEC
sfc: Use the correct maximum TX DMA ring size for SFC9100
Add Shradha Shah as the sfc driver maintainer.
net/vxlan: Share RX skb de-marking and checksum checks with ovs
tulip: cleanup by using ARRAY_SIZE()
ip_tunnel: clear IPCB in ip_tunnel_xmit() in case dst_link_failure() is called
net/cxgb4: Don't retrieve stats during recovery
...
This patch adds support for allocating IB UD QPs that we can steer
traffic from. We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE
and a capability bit.
This command isn't supported for VFs.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit f4ec9e9 "mlx4_core: Change bitmap allocator to work in round-robin fashion"
introduced round-robin allocation (via bitmap) for all resources which allocate
via a bitmap.
Round robin allocation is desirable for mcgs, counters, pd's, UARs, and xrcds.
These are simply numbers, with no involvement of ICM memory mapping.
Round robin is required for QPs, since we had a problem with immediate
reuse of a 24-bit QP number (commit f4ec9e9).
However, for other resources which use the bitmap allocator and involve
mapping ICM memory -- MPTs, CQs, SRQs -- round-robin is not desirable.
What happens in these cases is the following:
ICM memory is allocated and mapped in chunks of 256K.
Since the resource allocation index goes up monotonically, the allocator
will eventually require mapping a new chunk. Now, chunks are also unmapped
when their reference count goes back to zero. Thus, if a single app is
running and starts/exits frequently we will have the following situation:
When the app starts, a new chunk must be allocated and mapped.
When the app exits, the chunk reference count goes back to zero, and the
chunk is unmapped and freed. Therefore, the app must pay the cost of allocation
and mapping of ICM memory each time it runs (although the price is paid only when
allocating the initial entry in the new chunk).
For apps which allocate MPTs/SRQs/CQs and which operate as described above,
this presented a performance problem.
We therefore roll back the round-robin allocator modification for MPTs, CQs, SRQs.
Reported-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements resource quota grant decision when resources are requested,
for the following resources: QPs, CQs, SRQs, MPTs, MTTs, vlans, MACs,
and Counters.
When granting a resource, the quota system increases the allocated-count
for that slave.
When the slave later frees the resource, its allocated-count is reduced.
A spinlock is used to protect the integrity of each resource's free-pool counter.
(One slave may be in the process of being granted a resource while another
slave has crashed, initiating cleanup of that slave's resource quotas).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is step #1 for implementing SRIOV resource quotas for VFs.
Quotas are implemented per resource type for VFs and the PF, to prevent
any entity from simply grabbing all the resources for itself and leaving
the other entities unable to obtain such resources.
Resources which are allocated using quotas: QPs, CQs, SRQs, MPTs, MTTs, MAC,
VLAN, and Counters.
The quota system works as follows:
Each entity (VF or PF) is given a max number of a given resource (its quota),
and a guaranteed minimum number for each resource (starvation prevention).
For QPs, CQs, SRQs, MPTs and MTTs:
50% of the available quantity for the resource is divided equally among
the PF and all the active VFs (i.e., the number of VFs in the mlx4_core module
parameter "num_vfs"). This 50% represents the "guaranteed minimum" pool.
The other 50% is the "free pool", allocated on a first-come-first-serve basis.
For each VF/PF, resources are first allocated from its "guaranteed-minimum"
pool. When that pool is exhausted, the driver attempts to allocate from
the resource "free-pool".
The quota (i.e., max) for the VFs and the PF is:
The free-pool amount (50% of the real max) + the guaranteed minimum
For MACs:
Guarantee 2 MACs per VF/PF per port. As a result, since we have only
128 MACs per port, reduce the allowable number of VFs from 64 to 63.
Any remaining MACs are put into a free pool.
For VLANs:
For the PF, the per-port quota is 128 and guarantee is 64
(to allow the PF to register at least a VLAN per VF in VST mode).
For the VFs, the per-port quota is 64 and the guarantee is 0.
We assume that VGT VFs are trusted not to abuse the VLAN resource.
For Counters:
For all functions (PF and VFs), the quota is 128 and the guarantee is 0.
In this patch, we define the needed structures, which are added to the
resource-tracker struct. In addition, we do initialization
for the resource quota, and adjust the query_device response to use quotas
rather than resource maxima.
As part of the implementation, we introduce a new field in
mlx4_dev: quotas. This field holds the resource quotas used
to report maxima to the upper layers (ib_core, via query_device).
The HCA maxima of these values are passed to the VFs (via
QUERY_HCA) so that they may continue to use these in handling
QPs, CQs, SRQs and MPTs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In upstream kernels under SRIOV, the vlan register/unregister calls
were NOPs (doing nothing and returning OK). We detect these old
calls from guests (via the comm channel), since previously the
port number in mlx4_register_vlan was passed (improperly) in the
out_param. This has been corrected so that the port number is now
passed in bits 8..15 of the in_modifier field.
For old calls, these bits will be zero, so if the passed port
number is zero, we can still look at the out_param field to see
if it contains a valid port number. If yes, the VM is running
an old driver.
Since for old drivers, the register/unregister_vlan wrappers were
NOPs, we continue this policy -- the reason being that upstream
had an additional bug in eth driver running on guests (where
procedure mlx4_en_vlan_rx_kill_vid() had the following code:
if (!mlx4_find_cached_vlan(mdev->dev, priv->port, vid, &idx))
mlx4_unregister_vlan(mdev->dev, priv->port, idx);
else
en_err(priv, "could not find vid %d in cache\n", vid);
On a VM, mlx4_find_cached_vlan() will always fail, since the
vlan cache is located on the Hypervisor; on guests it is empty.
Therefore, if we allow upstream guests to register vlans, we will
have vlan leakage since the unregister will never be performed.
Leaving vlan reg/unreg for old guest drivers as a NOP is not a
feature regression, since in upstream the register/unregister
vlan wrapper is a NOP.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of vlan_index created problems unregistering vlans on guests.
In addition, tools delete vlan by tag, not by index, lets follow that.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds new firmware command and new firmware event. The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.
Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the firmware supports the UPDATE_QP command, if the VF link is disabled,
block all QPs opened by the VF, by programming the UPDATE_QP command to drop
all RX & TX traffic to/from these QPs. Operates only in VST mode.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Within VST mode, enable modifying the vlan and/or qos
for a VF without requiring unbind/rebind.
This requires firmware which supports the UPDATE_QP command.
(If the command is not available, we fall back to requiring
unbind/bind to activate these changes).
To avoid race conditions with modify-qp on QPs that are affected
by update-qp, this operation is performed on the comm_wq.
If the update operation succeeds for all the necessary QPs, a
vlan_unregister is performed for the abandoned vlan id.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to change the link state of VF (vPort)
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- XRC transport fixes
- Fix DHCP on IPoIB
- mlx4 preparations for flow steering
- iSER fixes
- miscellaneous other fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1ojD
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- XRC transport fixes
- Fix DHCP on IPoIB
- mlx4 preparations for flow steering
- iSER fixes
- miscellaneous other fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (23 commits)
IB/iser: Add support for iser CM REQ additional info
IB/iser: Return error to upper layers on EAGAIN registration failures
IB/iser: Move informational messages from error to info level
IB/iser: Add module version
mlx4_core: Expose a few helpers to fill DMFS HW strucutures
mlx4_core: Directly expose fields of DMFS HW rule control segment
mlx4_core: Change a few DMFS fields names to match firmare spec
mlx4: Match DMFS promiscuous field names to firmware spec
mlx4_core: Move DMFS HW structs to common header file
IB/mlx4: Set link type for RAW PACKET QPs in the QP context
IB/mlx4: Disable VLAN stripping for RAW PACKET QPs
mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level
RDMA/iwcm: Don't touch cmid after dropping reference
IB/qib: Correct qib_verbs_register_sysfs() error handling
IB/ipath: Correct ipath_verbs_register_sysfs() error handling
RDMA/cxgb4: Fix SQ allocation when on-chip SQ is disabled
SRPT: Fix odd use of WARN_ON()
IPoIB: Fix ipoib_hard_header() return value
RDMA: Rename random32() to prandom_u32()
RDMA/cxgb3: Fix uninitialized variable
...
Add support to ndo_set_vf_vlan in the driver. Once this call is used the vport
is considered to be in VST mode. In this mode, the PPF driver configures
Ethernet QPs created by this VF to use this vlan id and priority. Currently
RoCE isn't supported on that mode.
The special values of VID=4095 or VID=0,UP=0 are considered as VGT.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add struct mlx4_vport_state where all the parameters related
to management of VFs port (virtual ports of the NIC eswitch) are kept.
The driver keeps an administrative and operational copy of the settings.
The current administrative copy becomes operational on the event of probing
a VF either on a VM or on the host.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move flow steering HW structures to be on the public mlx4 include
directory, as a pre-step for the mlx4 IB driver to use them too.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Read HCA frequency, read PCI clock bar and offset, map internal clock to
PCI bar.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pre-step for supporting guests that use B0 steering over a hypervisor
that runs in DMFS (device managed flow steering mode). Add helper function
which allows to translate L2 attachments / detachments provided in B0 mode
to DMFS rules.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The set_param_l function assumes casting a u64 pointer to a u32 pointer
allows to access the lower 32bits, but it results in writing the upper
32 bits on big endian systems.
The fixed function reads the upper 32 bits of the 64 argument, and or's
them with the 32 bits of the 32-bit value passed to the function.
Since this is now a "read-modify-write" operation, we got many
"unintialized variable" warnings which needed to be fixed as well.
Reported-by: Alexander Schmidt <alexschm@de.ibm.com>.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- SRP error handling fixes from Bart Van Assche
- Implementation of memory windows for mlx4 from Shani Michaeli
- Lots of cxgb4 HW driver fixes from Vipul Pandya
- Make iSER work for virtual functions, other fixes from Or Gerlitz
- Fix for bug in qib HW driver from Mike Marciniszyn
- IPoIB fixes from me, Itai Garbi, Shlomo Pongratz, Yan Burman
- Various cleanups and warning fixes from Julia Lawall, Paul Bolle, Wei Yongjun
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=RAQw
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband update from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.9:
- SRP error handling fixes from Bart Van Assche
- Implementation of memory windows for mlx4 from Shani Michaeli
- Lots of cxgb4 HW driver fixes from Vipul Pandya
- Make iSER work for virtual functions, other fixes from Or Gerlitz
- Fix for bug in qib HW driver from Mike Marciniszyn
- IPoIB fixes from me, Itai Garbi, Shlomo Pongratz, Yan Burman
- Various cleanups and warning fixes from Julia Lawall, Paul Bolle,
Wei Yongjun"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (41 commits)
IB/mlx4: Advertise MW support
IB/mlx4: Support memory window binding
mlx4: Implement memory windows allocation and deallocation
mlx4_core: Enable memory windows in {INIT, QUERY}_HCA
mlx4_core: Disable memory windows for virtual functions
IPoIB: Free ipoib neigh on path record failure so path rec queries are retried
IB/srp: Fail I/O requests if the transport is offline
IB/srp: Avoid endless SCSI error handling loop
IB/srp: Avoid sending a task management function needlessly
IB/srp: Track connection state properly
IB/mlx4: Remove redundant NULL check before kfree
IB/mlx4: Fix compiler warning about uninitialized 'vlan' variable
IB/mlx4: Convert is_xxx variables in build_mlx_header() to bool
IB/iser: Enable iser when FMRs are not supported
IB/iser: Avoid error prints on EAGAIN registration failures
IB/iser: Use proper define for the commands per LUN value advertised to SCSI ML
IB/uverbs: Implement memory windows support in uverbs
IB/core: Add "type 2" memory windows support
mlx4_core: Propagate MR deregistration failures to caller
mlx4_core: Rename MPT-related functions to have mpt_ prefix
...
Add memory windows-related code to INIT_HCA and QUERY_HCA.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Do not enable memory windows allocation for virtual functions.
In addition, add a few safety checks, such as:
* Verifying the PD of a new MPT matches the VF.
* Making sure binding memory window isn't enabled for FMRs, and
that new memory windows are not FMR themselves.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The MPT - Memory Protection Table - is used by both memory windows and
memory regions. Hence, all MPT references are relevant for both types
of memory objects. Rename the relevant functions to start with mpt_
instead of the current mr_ prefix.
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Move low level code that deals with management of Ethernet MACs and QPs from mlx4_core to mlx4_en.
Also convert the new functions to deal with MACs in form of char array instead of u64.
Actual functions moved:
mlx4_replace_mac
mlx4_get_eth_qp
mlx4_put_eth_qp
To conduct this change, some functionality had to be exported from the core,
the following functions were added:
mlx4_get_base_qp
__mlx4_replace_mac (low level function for CX1/A0 compatibility)
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Firmware dynamically changes flow steering hash configuration from covering
L2 only to "full" L2/L3/L4 mode needed. The dynamic change allows the driver
to set hard coded hash configuration which is changed by the firmware from L2
to L2/L3/L4 when attaching the first L3/L4 flow steering rule and back to L2
when there are no more such rules.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the fields for struct mlx4_net_trans_rule_hw_ctrl were packed into u32
and accessed through bit field operations. Expose and access them directly as
u8.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device managed flow steering will be enabled only under administrator
directive provided through setting the existing module parameter
log_num_mgm_entry_size to -1 (if the device actually supports flow
steering). If flow steering isn't requested or not available, the
driver will use the value of log_num_mgm_entry_size and B0 steering.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Instead of having a hard-coded "PCI device ID != 0x1003" (which
obviously breaks as newer devices with ID != 0x1003 become available),
instead let's set a flag in our PCI device table for the older devices
where we're supposed to force using SENSE_PORT. This also avoids
enabling SENSE_PORT for virtual functions by mistake.
Signed-off-by: Roland Dreier <roland@purestorage.com>
That way we can check flags later on, when we've finished with the
pci_device_id structure. Also convert the "is VF" flag to an enum:
"Never do in the preprocessor what can be done in C."
Signed-off-by: Roland Dreier <roland@purestorage.com>
On an SR-IOV master device, __mlx4_init_one() calls mlx4_init_hca()
before mlx4_multi_func_init(). However, for unlucky configurations,
mlx4_init_hca() might call mlx4_SENSE_PORT() (via mlx4_dev_cap()), and
that calls mlx4_cmd_imm() with MLX4_CMD_WRAPPED set.
However, on a multifunction device with MLX4_CMD_WRAPPED, __mlx4_cmd()
calls into mlx4_slave_cmd(), and that immediately tries to do
down(&priv->cmd.slave_sem);
but priv->cmd.slave_sem isn't initialized until mlx4_multi_func_init()
(which we haven't called yet). The next thing it tries to do is access
priv->mfunc.vhcr, but that hasn't been allocated yet.
Fix this by moving the initialization of slave_sem and vhcr up into
mlx4_cmd_init(). Also, since slave_sem is really just being used as a
mutex, convert it into a slave_cmd_mutex.
Signed-off-by: Roland Dreier <roland@purestorage.com>
This is necessary in order to support > 1 VF/PF in a VM for software
that uses the node guid as a discriminator, such as librdmacm.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1. Allow only master to change node description.
2. Prevent AH leakage in send mads.
3. Take device part number from PCI structure, so that guests see the
VF part number (and not the PF part number).
4. Place the device revision ID into caps structure at startup.
5. SET_PORT in update_gids_task needs to go through wrapper on master.
6. In mlx4_ib_event(), PORT_MGMT_EVENT needs be handled in a work
queue on the master, since it propagates events to slaves using
GEN_EQE.
7. Do not support FMR on slaves.
8. Add spinlock to slave_event(), since it is called both in interrupt
context and in process context (due to 6 above, and also if
smp_snoop is used). This fix was found and implemented by Saeed
Mahameed <saeedm@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For an IB port, a slave should not show port active until that slave
has a valid alias-guid (provided by the subnet manager). Therefore
the port-up event should be passed to a slave only after both the port
is up, and the slave's alias-guid has been set.
Also, provide the infrastructure for propagating port-management
events (client-reregister, etc) to slaves.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This requires:
1. Replacing the paravirtualized P_Key index (inserted by the guest)
with the real P_Key index.
2. For UD QPs, placing the guest's true source GID index in the
address path structure mgid field, and setting the ud_force_mgid
bit so that the mgid is taken from the QP context and not from the
WQE when posting sends.
3. For UC and RC QPs, placing the guest's true source GID index in the
address path structure mgid field.
4. For tunnel and proxy QPs, setting the Q_Key value reserved for that
proxy/tunnel pair.
Since not all the above adjustments occur in all the QP transitions,
the QP transitions require separate wrapper functions.
Secondly, initialize the P_Key virtualization table to its default
values: Master virtualized table is 1-1 with the real P_Key table,
guest virtualized table has P_Key index 0 mapped to the real P_Key
index 0, and all the other P_Key indices mapped to the reserved
(invalid) P_Key at index 127.
Finally, add logic in smp_snoop for maintaining the phys_P_Key_cache.
and generating events on the master only if a P_Key actually changed.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
To allow for usage of the flow steering Firmware structures in more locations over the driver,
such as the resource tracker, move them from mcg.c to common header files.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some issues around int variables used in data structures related
to memory registration.
Handle int overflow in mlx4_init_icm_table by using a u64 intermediate
variable and changing struct mlx4_icm_table num_obj field to be u32.
Change some more fields/variables to use u32 instead of int to prevent
a case where the variable becomes negative when bit 31 is set.
Also subtract log_mtts_per_seg from the exponent when computing
num_mtt, since its added later on in that very same code area.
This and the previous commit fixes some issues which actually prevent
commit db5a7a65c0 ("mlx4_core: Scale size of MTT table with system
RAM") from working. Now, when the number of MTTs is scaled with the
size of the RAM we can map up to 8TB.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- Updates to the qib low-level driver
- First chunk of changes for SR-IOV support for mlx4 IB
- RDMA CM support for IPv6-only binding
- Other misc cleanups and fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=f09j
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- Updates to the qib low-level driver
- First chunk of changes for SR-IOV support for mlx4 IB
- RDMA CM support for IPv6-only binding
- Other misc cleanups and fixes
Fix up some add-add conflicts in include/linux/mlx4/device.h and
drivers/net/ethernet/mellanox/mlx4/main.c
* tag 'rdma-for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (30 commits)
IB/qib: checkpatch fixes
IB/qib: Add congestion control agent implementation
IB/qib: Reduce sdma_lock contention
IB/qib: Fix an incorrect log message
IB/qib: Fix QP RCU sparse warnings
mlx4: Put physical GID and P_Key table sizes in mlx4_phys_caps struct and paravirtualize them
mlx4_core: Allow guests to have IB ports
mlx4_core: Implement mechanism for reserved Q_Keys
net/mlx4_core: Free ICM table in case of error
IB/cm: Destroy idr as part of the module init error flow
mlx4_core: Remove double function declarations
IB/mlx4: Fill the masked_atomic_cap attribute in query device
IB/mthca: Fill in sq_sig_type in query QP
IB/mthca: Warning about event for non-existent QPs should show event type
IB/qib: Fix sparse RCU warnings in qib_keys.c
net/mlx4_core: Initialize IB port capabilities for all slaves
mlx4: Use port management change event instead of smp_snoop
IB/qib: RCU locking for MR validation
IB/qib: Avoid returning EBUSY from MR deregister
IB/qib: Fix UC MR refs for immediate operations
...
To allow easy paravirtualization of P_Key and GID table sizes, keep
paravirtualized sizes in mlx4_dev->caps, but save the actual physical
sizes from FW in struct: mlx4_dev->phys_cap.
In addition, in SR-IOV mode, do the following:
1. Reduce reported P_Key table size by 1.
This is done to reserve the highest P_Key index for internal use,
for declaring an invalid P_Key in P_Key paravirtualization.
We require a P_Key index which always contain an invalid P_Key
value for this purpose (i.e., one which cannot be modified by
the subnet manager). The way to do this is to reduce the
P_Key table size reported to the subnet manager by 1, so that
it will not attempt to access the P_Key at index #127.
2. Paravirtualize the GID table size to 1. Thus, each guest sees
only a single GID (at its paravirtualized index 0).
In addition, since we are paravirtualizing the GID table size to 1, we
add paravirtualization of the master GID event here (i.e., we do not
do ib_dispatch_event() for the GUID change event on the master, since
its (only) GUID never changes).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The port management change event can replace smp_snoop. If the
capability bit for this event is set in dev-caps, the event is used
(by the driver setting the PORT_MNG_CHG_EVENT bit in the async event
mask in the MAP_EQ fw command). In this case, when the driver passes
incoming SMP PORT_INFO SET mads to the FW, the FW generates port
management change events to signal any changes to the driver.
If the FW generates these events, smp_snoop shouldn't be invoked in
ib_process_mad(), or duplicate events will occur (once from the
FW-generated event, and once from smp_snoop).
In the case where the FW does not generate port management change
events smp_snoop needs to be invoked to create these events. The flow
in smp_snoop has been modified to make use of the same procedures as
in the fw-generated-event event case to generate the port management
events (LID change, Client-rereg, Pkey change, and/or GID change).
Port management change event handling required changing the
mlx4_ib_event and mlx4_dispatch_event prototypes; the "param" argument
(last argument) had to be changed to unsigned long in order to
accomodate passing the EQE pointer.
We also needed to move the definition of struct mlx4_eqe from
net/mlx4.h to file device.h -- to make it available to the IB driver,
to handle port management change events.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As with other device resources, the resource tracker is needed for supporting
device managed flow steering rules under SRIOV: make sure virtual functions
delete only rules created by them, and clean all rules attached by a crashed VF.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is modified to support three operation modes.
If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.
When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.
When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.
Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for firmware commands to attach/detach a new device managed
steering mode. Such network steering rules allow the user to provide an
L2/L3/L4 flow specification to the firmware and have the device to steer
traffic that matches that specification to the provided QP.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the IDs used by the resource tracker are of type u32, so far this was
ok since all the different resources we were tracking could be encoded in 32bit.
As a preparation step for tracking of resources whose IDs need > 32 bits such
as network flow steering rules, who are 64 bit in size, move to use 64 bit
based resource IDs.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the data structure used for managing the SRIOV resource tracking
mechanism from radix tree to red-black tree. This is preparation step
for supporting resource IDs which are 64bit long, such as network flow
steering rules. Such IDs can't be used as radix-tree keys on 32bit
architectures and hence the reason for the change.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- pass the following parameters:
- firmware version (added QUERY_FW paravirtualization for that)
- disable Blueflame on slaves. KVM disables write combining on guests,
and we get better performance without BF in this case. (This requires
QUERY_DEV_CAP paravirtualization, also in this commit)
- max qp rdma as destination
- get rid of a chunk of "if (0)" dead code
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing resource tracking for XRC domains and complete the tracking for HCA
network flow counters.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the slave and master resources are deleted after master freed
all bitmaps. If any resources were not properly cleaned up during the
shutdown process, an Oops would result.
Fix so that delete slave (only) resources during cleanup. Master resources
are cleaned up during unload process, and need not separately be cleaned.
Note that during cleanup, we need to split the resource-tracker freeing
functionality.
Before removing all the bitmaps, we free any leftover slave resources.
However, we can only remove the resource tracker linked list after
all bitmap frees, since some of the freeing functions (e.g.,
mlx4_cleanup_eq_table) use paravirtualized FW commands which expect
the resource tracker linked list to be present.
Found-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding QoS firmware commands:
- mlx4_en_SET_PORT_PRIO2TC - set UP <=> TC
- mlx4_en_SET_PORT_SCHEDULER - set promised BW, max BW and PG number
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stands out; by patch count lots of fixes to the mlx4 driver plus some
cleanups and fixes to the core and other drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=DbLx
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes for the 3.4 merge window from Roland Dreier:
"Nothing big really stands out; by patch count lots of fixes to the
mlx4 driver plus some cleanups and fixes to the core and other
drivers."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (28 commits)
mlx4_core: Scale size of MTT table with system RAM
mlx4_core: Allow dynamic MTU configuration for IB ports
IB/mlx4: Fix info returned when querying IBoE ports
IB/mlx4: Fix possible missed completion event
mlx4_core: Report thermal error events
mlx4_core: Fix one more static exported function
IB: Change CQE "csum_ok" field to a bit flag
RDMA/iwcm: Reject connect requests if cmid is not in LISTEN state
RDMA/cxgb3: Don't pass irq flags to flush_qp()
mlx4_core: Get rid of redundant ext_port_cap flags
RDMA/ucma: Fix AB-BA deadlock
IB/ehca: Fix ilog2() compile failure
IB: Use central enum for speed instead of hard-coded values
IB/iser: Post initial receive buffers before sending the final login request
IB/iser: Free IB connection resources in the proper place
IB/srp: Consolidate repetitive sysfs code
IB/srp: Use pr_fmt() and pr_err()/pr_warn()
IB/core: Fix SDR rates in sysfs
mlx4: Enforce device max FMR maps in FMR alloc
IB/mlx4: Set bad_wr for invalid send opcode
...
The current driver defaults to 1M MTT segments, where each segment holds
8 MTT entries. This limits the total memory registered to 8M * PAGE_SIZE
which is 32GB with 4K pages. Since systems that have much more memory
are pretty common now (at least among systems with InfiniBand hardware),
this limit ends up getting hit in practice quite a bit.
Handle this by having the driver allocate at least enough MTT entries to
cover 2 * totalram pages.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Set the MTU for IB ports in the driver instead of using the firmware
default of 2KB (the driver defaults to 4KB). Allow for dynamic mtu
configuration through a new, per-port sysfs entry.
Since there's a dependency between the port MTU and the max number of
HW VLs the port can support, apply a mim/max approach, using a loop
that goes down from the highest possible number of VLs to the lowest,
using the firmware return status to know whether the requested number
of VLs is possible with a given MTU.
For now, as with the dynamic link type change / VPI support, the sysfs
entry to change the mtu is exposed only when NOT running in SR-IOV
mode. To allow changing the MTU for the master in SR-IOV mode,
primary-function-initiated FLR (Function Level Reset) needs to be
implemented.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Print an error message when a thermal error async event is reported by the HW.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Dotan Barak <dotanb@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
While doing the work for commit a6f7feae6d ("IB/mlx4: pass SMP
vendor-specific attribute MADs to firmware") we realized that the
firmware would respond on all sorts of vendor-specific MADs.
Therefore commit 97285b7817 ("mlx4_core: Add extended port
capabilities support") adds redundant code into the driver, since
there's no real reaon to maintain the extended capabilities of the
port, as they can be queried on demand (e.g the FDR10 capability).
This patch reverts commit 97285b7817 and removes the check for
extended caps from the mlx4_ib driver port query flow.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Conflicts:
drivers/net/ethernet/sfc/rx.c
Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change
the rx_buf->is_page boolean into a set of u16 flags, and another to
adjust how ->ip_summed is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>
Under the spinlock we call request_irq(), which allocates memory with GFP_KERNEL,
This causes the following trace when DEBUG_SPINLOCK is enabled, it can cause
the following trace:
BUG: spinlock wrong CPU on CPU#2, ethtool/2595
lock: ffff8801f9cbc2b0, .magic: dead4ead, .owner: ethtool/2595, .owner_cpu: 0
Pid: 2595, comm: ethtool Not tainted 3.0.18 #2
Call Trace:
spin_bug+0xa2/0xf0
do_raw_spin_unlock+0x71/0xa0
_raw_spin_unlock+0xe/0x10
mlx4_assign_eq+0x12b/0x190 [mlx4_core]
mlx4_en_activate_cq+0x252/0x2d0 [mlx4_en]
? mlx4_en_activate_rx_rings+0x227/0x370 [mlx4_en]
mlx4_en_start_port+0x189/0xb90 [mlx4_en]
mlx4_en_set_ringparam+0x29a/0x340 [mlx4_en]
dev_ethtool+0x816/0xb10
? dev_get_by_name_rcu+0xa4/0xe0
dev_ioctl+0x2b5/0x470
handle_mm_fault+0x1cd/0x2d0
sock_do_ioctl+0x5d/0x70
sock_ioctl+0x79/0x2f0
do_vfs_ioctl+0x8c/0x340
sys_ioctl+0xa1/0xb0
system_call_fastpath+0x16/0x1b
Replacing with mutex, which is enough in this case.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary field high_prios from mlx4_steer struct and initialization
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slave async events were mapped to single eq. This patch fixes this issue, so
the slaves can map the async events to any eq.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Added module parameters sr_iov and probe_vf for controlling enablement of
SRIOV mode.
2. Increased default max num-qps, num-mpts and log_num_macs to accomodate
SRIOV mode
3. Added port_type_array as a module parameter to allow driver startup with
ports configured as desired.
In SRIOV mode, only ETH is supported, and this array is ignored; otherwise,
for the case where the FW supports both port types (ETH and IB), the
port_type_array parameter is used.
By default, the port_type_array is set to configure both ports as IB.
4. When running in sriov mode, the master needs to initialize the ICM eq table
to hold the eq's for itself and also for all the slaves.
5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap.
6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures
mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow
modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca).
VFs obtain their startup information from the PF (master) device via the
comm channel.
7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver
aborts loading the device.
8. Do not allow setting port type via sysfs when running in SRIOV mode.
9. mlx4_get_ownership: Currently, only one PF is supported by the driver.
If the HCA is burned with FW which enables more than one PF, only one
of the PFs is allowed to run. The first one up grabs a FW ownership
semaphone -- all other PFs will find that semaphore taken, and the
driver will not allow them to run.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Liran Liss <liranl@mellanox.co.il>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous implementation mtts are managed by:
1. order - log(mtt segments), 'mtt segment' groups several mtts together.
2. first_seg - segment location relative to mtt table.
In the current implementation:
1. order - log(mtts) rather than segments
2. offset - mtt index in mtt table
Note: The actual mtt allocation is made in segments but it is
transparent to callers.
Rational: The mtt resource holders are not interested on how the allocation
of mtt is done, but rather on how they will use it.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The physical port is now common to the PF and VFs.
The port resources and configuration is managed by the PF, VFs can
only influence the MTU of the port, it is set as max among all functions,
Each function allocates RX buffers of required size to meet it's MTU enforcement.
Port management code was moved to mlx4_core, as the mlx4_en module is
virtualization unaware
Move handling qp functionality to mlx4_get_eth_qp/mlx4_put_eth_qp
including reserve/release range and add/release unicast steering.
Let mlx4_register/unregister_mac deal only with MAC (un)registration.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let multicast/unicast attaching flow go through resource tracker.
The PF is the one responsible for managing all the steering entries.
Define and use module parameter that determines the number of qps
per multicast group.
Minor changes in function calls according to changed prototype.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The resource tracker is used to track usage of HCA resources by the different
guests.
Virtual functions (VFs) are attached to guest operating systems but
resources are allocated from the same pool and are assigned to VFs. It is
essential that hostile/buggy guests not be able to affect the operation of
other VFs, possibly attached to other guest OSs since ConnectX firmware is not
tolerant to misuse of resources.
The resource tracker module associates each resource with a VF and maintains
state information for the allocated object. It also defines allowed state
transitions and enforces them.
Relationships between resources are also referred to. For example, CQs are
pointed to by QPs, so it is forbidden to destroy a CQ if a QP refers to it.
ICM memory is always accessible through the primary function and hence it is
allocated by the owner of the primary function.
When a guest dies, an FLR is generated for all the VFs it owns and all the
resources it used are freed.
The tracked resource types are: QPs, CQs, SRQs, MPTs, MTTs, MACs, RES_EQs,
and XRCDNs.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
MTTs are resources which are allocated and tracked by the PF driver.
In multifunction mode, the allocation and icm mapping is done in
the resource tracker (later patch in this sequence).
To accomplish this, we have "work" functions whose names start with
"__", and "request" functions (same name, no __). If we are operating
in multifunction mode, the request function actually results in
comm-channel commands being sent (ALLOC_RES or FREE_RES).
The PF-driver comm-channel handler will ultimately invoke the
"work" (__) function and return the result.
If we are not in multifunction mode, the "work" handler is invoked
immediately.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commands are added here:
1. QUERY_FUNC_CAP and its wrapper. This function is used by VFs when
they start up to receive configuration information from the PF, such
as resource quotas for this VF, which ports should be used (currently
two), what protocol is running on the port (currently Ethernet ONLY,
or port not active).
2. QUERY_PORT and its wrapper. Previously, this FW command was invoked directly
by the ETH driver (en_port.c) using mlx4_cmd_box. Virtualization is now
required here (the VF's MAC address must be substituted for the PFs
MAC address returned by the FW). We changed the invocation
in the ETH driver to use mlx4_QUERY_PORT, and added the wrapper.
3. QUERY_HCA. Used by the VF to determine how the HCA was initialized.
For now, we need only the multicast table member entry size
(log2_mc_table_entry_sz, in the ConnectX PRM). No wrapper is needed
here, because the data may be passed as is to the VF without modification).
In this command, we have added a GLOBAL_CAPS field for passing required
configuration information from FW to a VF (this field is to allow safely
adding new SRIOV capabilities which require support in VF drivers, too).
Bits will set here by FW in response to PF-driver configuration commands which
will activate as yet undefined new SRIOV features. The VF will test to see that
all required capabilities indicated by this field are supported (i.e., if a bit
is set and the VF driver does not recognize that bit, it must abort
its initialization). Currently, no bits are set.
4. Added a CLOSE_PORT wrapper. The PF context needs to keep track of how many VF contexts
have the port open. The PF context will not actually issue the FW close port command
until the last port user issues a CLOSE_PORT request.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: Marcel Apfelbaum <marcela@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SRIOV is enabled on the chip (at FW burning time),
the HCA uses only 17 bits for the PD. The remaining 7 high-order bits
are ignored.
Change the allocator to return only 17 bits for the PD. The MSB 7
bits will be used to encode the slave number for consistency
checking later on in the resource tracker.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
These changes will not affect module operation as yet. They
are only to get some structs and enums in place for use by
subsequent patches (making those smaller).
Added here:
* sriov state structs and inlines (mlx4_is_master/slave/mfunc)
* comm-channel and vhcr support structures
* enum values for new FW and comm-channel virtual commands
(i.e., commands, passed via the comm channel to the PF-driver).
* prototypes for many command wrapper functions (used by the
PF context for processing FW commands passed to it by the VFs).
* struct mlx4_eqe is moved from eq.c to mlx4.h (it will be used
by other mlx4_core source files).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (62 commits)
mlx4_core: Deprecate log_num_vlan module param
IB/mlx4: Don't set VLAN in IBoE WQEs' control segment
IB/mlx4: Enable 4K mtu for IBoE
RDMA/cxgb4: Mark QP in error before disabling the queue in firmware
RDMA/cxgb4: Serialize calls to CQ's comp_handler
RDMA/cxgb3: Serialize calls to CQ's comp_handler
IB/qib: Fix issue with link states and QSFP cables
IB/mlx4: Configure extended active speeds
mlx4_core: Add extended port capabilities support
IB/qib: Hold links until tuning data is available
IB/qib: Clean up checkpatch issue
IB/qib: Remove s_lock around header validation
IB/qib: Precompute timeout jiffies to optimize latency
IB/qib: Use RCU for qpn lookup
IB/qib: Eliminate divide/mod in converting idx to egr buf pointer
IB/qib: Decode path MTU optimization
IB/qib: Optimize RC/UC code by IB operation
IPoIB: Use the right function to do DMA unmap pages
RDMA/cxgb4: Use correct QID in insert_recv_cqe()
RDMA/cxgb4: Make sure flush CQ entries are collected on connection close
...
Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and
make the necessary Kconfig and Makefile changes.
CC: Roland Dreier <roland@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Matan Barak