Expose new driver-specific "acl_region_rehash_interval" devlink param
which would allow user to alter default ACL region rehash interval.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hints priv comes from ERP code and it is possible to obtain it from
TCAM code. Add arg to appropriate functions so the hints
priv could be passed back down to ERP code. Pass NULL now as the
follow-up patches would pass an actual hints priv pointer.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce an initial implementation of rehash logic in ERP code.
Currently, the rehash is considered as needed only in case number of
roots in the hints is smaller than the number of roots actually in use.
In that case return hints pointer and let it be obtained through the
callpath through the Spectrum-2 TCAM op.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to pass ruleset/group and chunk pointers on action_replace call
path, nobody uses them.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, instead of providing the ID of the virtual router (VR)
where NVE underlay lookups will occur as in Spectrum-1, the ID of a
router interface (RIF) in this VR is required.
Expose functions to create and destroy such a RIF.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set RIF ops array as member of mlxsw_sp in order to control which RIF
operations callbacks are called per ASIC type. This is needed to control
per ASIC handling of loopback RIF configurations.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to abuse VID 1 anymore and we can instead use VID 4095
as the default VLAN, which will be configured on the port throughout its
lifetime.
The OVS join / leave functions are changed to enable VIDs 1-4094
(inclusive) instead of 2-4095. This because VID 4095 is now the default
VLAN instead of 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches will need to access the default port VLAN. Since this
VLAN will exist throughout the lifetime of the port, simply store it in
the port's struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches are going to replace the current default VID (1) with
VLAN_N_VID - 1 (4095).
Prepare for this conversion by replacing the hard-coded '1' with a
define.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In symmetric routing, the only two members in the VLAN corresponding to
the L3 VNI are the router port and the VXLAN tunnel.
In case the VXLAN device is already enslaved to the bridge and only
later the VLAN interface is configured, the tunnel will not be
offloaded.
The reason for this is that when the router interface (RIF)
corresponding to the VLAN interface is configured, it calls the core
fid_get() API which does not check if NVE should be enabled on the FID.
Instead, call into the bridge code which will check if NVE should be
enabled on the FID.
This effectively means that the same code path is used to retrieve a FID
when either a local port or a router port joins the FID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the past we had multiple instances where RIFs were not properly
deleted.
One of the reasons for leaking a RIF was that at the time when IP
addresses were flushed from the respective netdev (prompting the
destruction of the RIF), the netdev was no longer a mlxsw upper. This
caused the inet{,6}addr notification blocks to ignore the NETDEV_DOWN
event and leak the RIF.
Instead of checking whether the netdev is our upper when an IP address
is removed, we can instead check if the netdev has a RIF configured.
To look up a RIF we need to access mlxsw private data, so the patch
stores the notification blocks inside a mlxsw struct. This then allows
us to use container_of() and extract the required private data.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b3529af6bb ("spectrum: Reference count VLAN entries") started
reference counting port-VLAN entries in a similar fashion to the 8021q
driver.
However, this is not actually needed and only complicates things.
Instead, the driver should forbid the creation of a VLAN on a port if
this VLAN already exists. This would also solve the issue fixed by the
mentioned commit.
Therefore, remove the get()/put() API and use create()/destroy()
instead.
One place that needs special attention is VLAN addition in a VLAN-aware
bridge via switchdev operations. In case the VLAN flags (e.g., 'pvid')
are toggled, then the VLAN entry already exists. To prevent the driver
from wrongly returning EEXIST, the driver is changed to check in the
prepare phase whether the entry already exists and only returns an error
in case it is not associated with the correct bridge port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is no longer used. Remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when a RIF is constructed on top of a FID, the RIF increments
the FID's reference count and the RIF is destroyed when the FID's
reference count drops to 1. This effectively means that when no local
ports are member in the FID, the FID is destroyed regardless if the
router port is a member in the FID or not.
The above can lead to the unexpected behavior in which routes using a
VLAN interface as their nexthop device are no longer offloaded after the
last local port leaves the corresponding VLAN (FID).
Example:
# ip -4 route show dev br0.10
192.0.2.0/24 proto kernel scope link src 192.0.2.1 offload
# bridge vlan del vid 10 dev swp3
# ip -4 route show dev br0.10
192.0.2.0/24 proto kernel scope link src 192.0.2.1
After the patch, the route is offloaded before and after the VLAN is
removed from local port 'swp3', as the RIF corresponding to 'br0.10'
continues to exists.
In order to remove RIFs' reliance on the underlying FID's reference
count, we need to add a reference count to sub-port RIFs, which are RIFs
that correspond to physical ports and their uppers (e.g., LAG devices).
In this case, each {Port, VID} ('struct mlxsw_sp_port_vlan') needs to
hold a reference on the RIF. For example:
bond0.10
|
bond0
|
+-------+
| |
swp1 swp2
Both {Port 1, VID 10} and {Port 2, VID 10} will hold a reference on the
RIF corresponding to 'bond0.10'. When the last reference is dropped, the
RIF will be destroyed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Spectrum hardware demands that all router interfaces in the system
have the same first 38 resp. 36 bits of MAC address: the former limit
holds on Spectrum, the latter on Spectrum-2. Add a field that refers to
the required prefix mask and initialize in mlxsw_sp1_init() and
mlxsw_sp2_init().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare mlxsw_sp_netdevice_router_port_event() for handling of
NETDEV_PRE_CHANGEADDR. Split out the part that deals with the actual
changes and call it for the two events currently handled.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, when ACL rule was created its action was created with it.
It suits well for tc flower where ACL rule always needs an action, however
it does not suit multicast router, where the action is created prior to
setting a route, which in Spectrum-2 is actually an ACL rule.
Add support for rule creation without action creation. Do it by adding
afa_block argument to mlxsw_sp_acl_rule_create, which if NULL then an
action would be created, also add an indication within struct
mlxsw_sp_acl_rule_info that tells if the action should be destroyed when
the rule is destroyed.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast routes actions may be updated after creation. An example for that
is an addition of an egress interface to an existing route.
So far, as tc flower API dictated, ACL rules were either created or
deleted. Since multicast routes in Spectrum-2 are written to ACL as any
rule, it is required to allow the update of a rule's action as it may
change.
Add methods and operations to support updating rule's action. This is
supported only for Spectrum-2.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add specific ACL operations needed for programming multicast routing ACL
groups and routes.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are any offloaded FDB entries at bridge master of an NVE device
at the time that it's un-offloaded, their offloaded marks need to be
cleared. How that is done depends on whether the bridge in question is
vlan aware. Therefore add a per-FID-type operation.
Implement the operation for the 802.1q and 802.1d bridges.
Add and publish a function mlxsw_sp_fid_fdb_clear_offload() to dispatch
to the new operation according to FID type.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The notifier block will need to be passed to vxlan_fdb_replay() in a
follow-up patch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A follow-up patch will add support for replay and for clearing of
offload marks. These are NVE type-sensitive operations, and to be able
to dispatch them properly, a FID needs to know what NVE type is attached
to it.
Therefore, track the NVE type at struct mlxsw_sp_fid. Extend
mlxsw_sp_fid_vni_set() to take it as an argument, and add
mlxsw_sp_fid_nve_type().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1c30d1836a ("mlxsw: spectrum: Enable VxLAN enslavement to
bridges") enabled the enslavement of VxLAN devices to bridges that have
mlxsw ports (or their upper) as slaves. This patch extends mlxsw to also
support VLAN-aware bridges.
The patch is similar in nature to mentioned commit, but there is one
major difference. With VLAN-aware bridges, the VxLAN device's VNI is
mapped to the VLAN that is configured as PVID and egress untagged on the
bridge port.
Therefore, the driver is extended to listen to VLAN configuration on
VxLAN devices of interest and enable / disable NVE encapsulation on the
corresponding 802.1Q FIDs.
To prevent ambiguity, the driver makes sure that a given VLAN is not
configured as PVID and egress untagged on multiple VxLAN devices. This
sanitization takes place both when a port is enslaved to a bridge with
existing VxLAN devices and when a VLAN is added to / removed from a
VxLAN device of interest.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vxlan_join() function resolves the FID on which the VNI should be
set and then sets the VNI. Currently, the FID is simply resolved
according to the ifindex of the bridge device to which the VxLAN device
is enslaved. This works because only VLAN-unaware bridges are supported.
With VLAN-aware bridges the FID would need to be resolved based on the
VLAN to which the VNI is mapped to.
Add the VLAN ID to the argument list of the function.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_bridge_vxlan_leave() is currently split between
VLAN-aware and VLAN-unaware bridges, but actually both types can use the
same function.
The function needs to resolve the FID that corresponds to the VxLAN
device and disable NVE encapsulation on it. Instead of looking up the
FID differently for VLAN-aware and VLAN-unaware bridges, we can always
use the VxLAN's device VNI.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to commit 564c6d727a ("mlxsw: spectrum_fid: Add
APIs to lookup FID without creating it"), add a corresponding API to
lookup 802.1Q FIDs.
This is a prerequisite to VxLAN support with VLAN-aware bridges and will
allow us to resolve a 802.1Q FID by its VLAN when an FDB entry is added
on the bridge port of the VxLAN device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring an FDB entry pointing to a LAG netdev (or its upper),
the driver should only set the 'lag_vid' field when the FID (filtering
identifier) is of 802.1D type.
Extend the 802.1D FID family with an attribute indicating whether this
field should be set and based on its value set the field or leave it
blank.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB notifications for entries learned from an NVE tunnel contain the IP
address of the remote VTEP. In the case of IPv4 underlay, the IP address
is specified as-is. IPv6 addresses on the other hand, are specified as
handles which then need to be used to query the actual address from the
device.
Only IPv4 underlay is currently supported, so we cannot receive
notifications for IPv6 addresses and therefore an error is returned when
one tries to resolve such an address.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When processing a notification about a new FDB entry learned from a
VxLAN tunnel, the driver is provided with the FID index among other
parameters.
The driver potentially needs to update the bridge and VxLAN drivers
about the new entry using a pointer to the VxLAN device and the
corresponding VNI.
These two parameters are stored in the FID, so add a new function that
allows looking up a FID based on its index.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver periodically polls for new FDB entries learned by the device.
In the case of an FDB entry learned from a VxLAN tunnel, the
notification includes the IP of the remote VTEP, the filtering
identifier (FID) and the source MAC address of the overlay packet.
Assuming learning is enabled in the VxLAN and bridge drivers, the driver
needs to generate a notification and update them about the new FDB
entry.
Store the ifindex of the NVE device in the FID so that the driver will
be able to update the VxLAN and bridge drivers using it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enslavement of VxLAN devices to offloaded bridges was never forbidden by
mlxsw, but this patch makes sure the required configuration is performed
in order to allow VxLAN encapsulation and decapsulation to take place in
the device.
The patch handles both the case where a VxLAN device is enslaved to an
already offloaded bridge and the case where the first mlxsw port is
enslaved to a bridge that already has VxLAN device configured.
Invalid configurations are sanitized and an error string is returned via
extack.
Since encapsulation and decapsulation do not occur when the VxLAN device
is down, the driver makes sure to enable / disable these functionalities
based on NETDEV_PRE_UP and NETDEV_DOWN events.
Note that NETDEV_PRE_UP is used in favor of NETDEV_UP, as the former
allows to veto the operation, if necessary.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Spectrum ASIC supports different types of NVE encapsulations (e.g.,
VxLAN, NVGRE) with more types to be supported by future ASICs.
Despite being different, all these encapsulations share some common
functionality such as the enablement of NVE encapsulation on a given
filtering identifier (FID) and the addition of remote VTEPs to the
linked-list of VTEPs that traffic should be flooded to.
Implement this common core and allow different ASICs to register
different operations for different encapsulation types.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, different VRFs (routing tables) are represented using
different virtual routers (VRs) and thus the kernel's table IDs are
mapped to VR IDs.
Allow internal users of the IP router to query the VR ID based on a
kernel table ID.
This is needed - for example - when configuring the underlay VR where
VxLAN encapsulated packets will undergo an L3 lookup. In this case, the
kernel's table ID is derived from the VxLAN device's configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an NVE tunnel with an IP underlay (e.g., VxLAN) is configured the
local route to the tunnel's source IP needs to be promoted to perform
NVE decapsulation.
Expose an API in the unicast IP router to promote / demote local routes.
The case where a local route is configured after the creation of the NVE
tunnel will be handled in a subsequent patch in the set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current APIs only allow looking for a FID and creating it in case it
does not exist.
With VxLAN, in case the bridge to which the VxLAN device was enslaved
does not already have a corresponding FID, then it means that something
went wrong that we need to be aware of.
Add an API to look up a FID, but without creating it in order to catch
above-mentioned situation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, the VNI and the list of remote VTEPs a packet should be
flooded to is a property of the filtering identifier (FID).
During encapsulation, the VNI is taken from the FID the packet was
classified to. During decapsulation, the overlay packet is injected into
a bridge and classified to a FID based on the VNI it came with.
Allow NVE configuration for a FID. Currently, this is only supported
with 802.1D FIDs which are used for VLAN-unaware bridges. However, NVE
configuration is going to be supported with 802.1Q FIDs which is why the
related fields are placed in the common FID struct.
Since the device requires a 1:1 mapping between FID and VNI, the driver
maintains a hashtable keyed by VNI and checks if the VNI is already
associated with an existing FID.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device needs to flood an overlay packet to remote VTEPs it
retrieves a pointer to the head of a linked-list of records that store
the IP addresses of these VTEPs.
These records are stored in the KVD linear memory and configured via the
Tunneling NVE Underlay Multicast Table (TNUMT) register.
Add a new KVD linear entry type for these records, so that we will be
able to allocate and free them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L3 protocol and address definitions are going to be used by the NVE
code, so move them to the global header file from the one private to the
router.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The spectrum_router.h header file is private to the router block and
should only be included by direct consumers of it, such as dpipe and the
multicast routing code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bridge device is removed, the VLANs are flushed from each
configured port. This causes the ports to decrement the reference count
on the associated FIDs (filtering identifier). If the reference count of
a FID is 1 and it has a RIF (router interface), then this RIF is
destroyed.
However, if no port is member in the VLAN for which a RIF exists, then
the RIF will continue to exist after the removal of the bridge. To
reproduce:
# ip link add name br0 type bridge vlan_filtering 1
# ip link set dev swp1 master br0
# ip link add link br0 name br0.10 type vlan id 10
# ip address add 192.0.2.0/24 dev br0.10
# ip link del dev br0
The RIF associated with br0.10 continues to exist.
Fix this by iterating over all the bridge device uppers when it is
destroyed and take care of destroying their RIFs.
Fixes: 99f44bb352 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As recent spectrum FW imposes a limitation on using vlan_id key for
egress ACL, disallow the usage of that key accordingly and return a
proper extack message.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The APP TLVs are used for communicating priority-to-protocol ID maps for
a given netdevice. Support the following APP TLVs:
- DSCP (selector 5) to configure priority-to-DSCP code point maps. Use
these maps to configure packet priority on ingress, and DSCP code
point rewrite on egress.
- Default priority (selector 1, PID 0) to configure priority for the
DSCP code points that don't have one assigned by the DSCP selector. In
future this could also be used for assigning default port priority
when a packet arrives without DSCP tagging.
Besides setting up the maps themselves, also configure port trust level
and rewrite bits.
Port trust level determines whether, for a packet arriving through a
certain port, the priority should be determined based on PCP or DSCP
header fields. So far, mlxsw kept the device default of trust-PCP. Now,
as soon as the first DSCP APP TLV is configured, switch to trust-DSCP.
Only when all DSCP APP TLVs are removed, switch back to trust-PCP again.
Note that the default priority APP TLV doesn't impact the trust level
configuration.
Rewrite bits determine whether DSCP and PCP fields of egressing packets
should be updated according to switch priority. When port trust is
switched to DSCP, enable rewrite of DSCP field.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each TCAM region currently uses its own resources and there is no
sharing between the different regions.
This is going to change with A-TCAM as each region will need to allocate
an eRP table from the global eRP tables array.
Make the global TCAM resources available to each region by passing the
TCAM private data to the region initialization routine.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate extack pointer in order to add extack messages for ACL.
In the follow-up patches, appropriate messages will be added
in various points.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since cld_flower provides information about the filter template for
specific chain, use this information in order to prepare a region.
Use the template to find out what elements are going to be used
and pass that down to mlxsw_sp_acl_tcam_group_add(). Later on, when the
first filter is inserted, the mlxsw_sp_acl_tcam_group_use_patterns()
function would use this element usage information instead of looking
up a pattern.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize only C-TCAM for now. Do very minimal A-TCAM initialization in
order to make C-TCAM work.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, ACL regions that use 8 or 12 key blocks require several
consecutive hardware regions.
In order to allow defragmentation, the device stores a mapping from a
logical region ID to an hardware region ID, which is similar to the page
table that is used to translate virtual addresses to physical addresses.
Add the region association callback to the region create sequence and
implement it as a NOP in Spectrum which does not require it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce key blocks for Spectrum-2 that contains the same elements used
already for Spectrum1. Along with that, introduce encoder stub.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-2, no action set is stored directly in TCAM, all are located
in KVD linear. So ask core to treat the first set as dummy empty one,
to be just used for PTCEV2 purposes.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Pirko