Pull timer updates from Thomas Gleixner:
"Yet another big pile of changes:
- More year 2038 work from Arnd slowly reaching the point where we
need to think about the syscalls themself.
- A new timer function which allows to conditionally (re)arm a timer
only when it's either not running or the new expiry time is sooner
than the armed expiry time. This allows to use a single timer for
multiple timeout requirements w/o caring about the first expiry
time at the call site.
- A new NMI safe accessor to clock real time for the printk timestamp
work. Can be used by tracing, perf as well if required.
- A large number of timer setup conversions from Kees which got
collected here because either maintainers requested so or they
simply got ignored. As Kees pointed out already there are a few
trivial merge conflicts and some redundant commits which was
unavoidable due to the size of this conversion effort.
- Avoid a redundant iteration in the timer wheel softirq processing.
- Provide a mechanism to treat RTC implementations depending on their
hardware properties, i.e. don't inflict the write at the 0.5
seconds boundary which originates from the PC CMOS RTC to all RTCs.
No functional change as drivers need to be updated separately.
- The usual small updates to core code clocksource drivers. Nothing
really exciting"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (111 commits)
timers: Add a function to start/reduce a timer
pstore: Use ktime_get_real_fast_ns() instead of __getnstimeofday()
timer: Prepare to change all DEFINE_TIMER() callbacks
netfilter: ipvs: Convert timers to use timer_setup()
scsi: qla2xxx: Convert timers to use timer_setup()
block/aoe: discover_timer: Convert timers to use timer_setup()
ide: Convert timers to use timer_setup()
drbd: Convert timers to use timer_setup()
mailbox: Convert timers to use timer_setup()
crypto: Convert timers to use timer_setup()
drivers/pcmcia: omap1: Fix error in automated timer conversion
ARM: footbridge: Fix typo in timer conversion
drivers/sgi-xp: Convert timers to use timer_setup()
drivers/pcmcia: Convert timers to use timer_setup()
drivers/memstick: Convert timers to use timer_setup()
drivers/macintosh: Convert timers to use timer_setup()
hwrng/xgene-rng: Convert timers to use timer_setup()
auxdisplay: Convert timers to use timer_setup()
sparc/led: Convert timers to use timer_setup()
mips: ip22/32: Convert timers to use timer_setup()
...
MIPS will soon not be a part of Imagination Technologies, and as such
many @imgtec.com email addresses will no longer be valid. This patch
updates the addresses for those who:
- Have 10 or more patches in mainline authored using an @imgtec.com
email address, or any patches dated within the past year.
- Are still with Imagination but leaving as part of the MIPS business
unit, as determined from an internal email address list.
- Haven't already updated their email address (ie. JamesH) or expressed
a desire to be excluded (ie. Maciej).
- Acked v2 or earlier of this patch, which leaves Deng-Cheng, Matt &
myself.
New addresses are of the form firstname.lastname@mips.com, and all
verified against an internal email address list. An entry is added to
.mailmap for each person such that get_maintainer.pl will report the new
addresses rather than @imgtec.com addresses which will soon be dead.
Instances of the affected addresses throughout the tree are then
mechanically replaced with the new @mips.com address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Cc: Deng-Cheng Zhu <dengcheng.zhu@mips.com>
Acked-by: Dengcheng Zhu <dengcheng.zhu@mips.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@mips.com>
Acked-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: trivial@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Tested-by: Paul Burton <paul.burton@mips.com> # for img-ascii-lcd
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f4757af ("staging: panel: Fix single-open policy race condition")
introduced in 3.19-rc1 attempted to fix a race condition on the open, but
failed to properly do it and used to exit without restoring the semaphore.
This results in -EBUSY being returned after the first open error until
the module is reloaded or the system restarted (ie: consecutive to a
dual open resulting in -EBUSY or to a permission error).
[ Note for stable maintainers: the code moved from drivers/misc/panel.c
to drivers/auxdisplay/{charlcd,panel}.c during 4.12. The patch easily
applies there (modulo the renamed atomic counter) but I can provide a
tested backport if desired. ]
Fixes: f4757af85 # 3.19-rc1
Cc: stable@vger.kernel.org
Cc: Mariusz Gorski <marius.gorski@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
charlcd_ops are not supposed to change at runtime. All functions
working with charlcd_ops provided by <misc/charlcd.h> work with
const charlcd_ops. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
12750 560 362 13672 3568 drivers/auxdisplay/panel.o
File size After adding 'const':
text data bss dec hex filename
12942 368 362 13672 3568 drivers/auxdisplay/panel.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like arm-charlcd.c belongs to auxdisplay subsystem.
Move it to drivers/auxdisplay folder.
No functional changes intended.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It looks like panel.c belongs to auxdisplay subsystem.
Move it to drivers/auxdisplay folder.
No functional changes intended.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The data read from the device is 3 little-endian words, so let's
annotate them as such and use le16_to_cpu() to convert them to host
endianness - it might turn out to be a bit more performant, and it
expresses the conversion more clearly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/auxdisplay/img-ascii-lcd.ko | grep alias
$
After this patch:
$ modinfo drivers/auxdisplay/img-ascii-lcd.ko | grep alias
alias: of:N*T*Cmti,sead3-lcdC*
alias: of:N*T*Cmti,sead3-lcd
alias: of:N*T*Cmti,malta-lcdC*
alias: of:N*T*Cmti,malta-lcd
alias: of:N*T*Cimg,boston-lcdC*
alias: of:N*T*Cimg,boston-lcd
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc-7.0.1 points out that we copy uninitialized data from the stack
into a per-device structure:
drivers/auxdisplay/ht16k33.c: In function 'ht16k33_keypad_irq_thread':
arch/x86/include/asm/string_32.h:78:16: error: 'new_state' may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/x86/include/asm/string_32.h:79:22: error: '*((void *)&new_state+4)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The access is harmless because we never read the data, but we are better
off not doing this, so this changes the code to only copy the data
that was actually initialized. To make sure we don't overflow the
stack with an incorrect DT, we also need to add a sanity checkin the
probe function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Robin van der Gracht <robin@protonic.nl>
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DT properties specifying physical properties should contain appropriate
suffices indicating the units of measurement.
Hence amend the HD44780 DT bindings to add "chars" suffixes to the
"display-height" and "display-width" properties, and update the driver
to parse them.
Fixes: dd9502a9e9 ("dt-bindings: auxdisplay: Add bindings for Hitachi HD44780")
Fixes: d47d88361f ("auxdisplay: Add HD44780 Character LCD support")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Hitachi HD44780 Character LCD Controller is commonly used on
character LCDs that can display one or more lines of text.
This driver supports character LCDs connected to GPIOs, using either a
4-bit or 8-bit data bus, and provides access through the charlcd core
and /dev/lcd.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On displays with more than two lines, the additional lines are stored in
the buffers used for the first two lines, but beyond the visible parts.
Adjust the DDRAM address calculation to cater for this.
When clearing the display, avoid writing more spaces than the actual
size of the physical buffer.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 4-bit mode, 8-bit commands and data are written using two raw writes
to the data interface: high nibble first, low nibble last. This must be
handled by the low-level driver.
However, as we don't know in which mode (4-bit or 8-bit) nor 4-bit phase
the LCD was left, initialization must always be handled using raw
writes, and needs to configure the LCD for 8-bit mode first.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract the character LCD core from the Parallel port LCD/Keypad Panel
driver in the misc subsystem, and convert it into a subdriver in the
auxdisplay subsystem. This allows the character LCD core to be used by
other drivers later.
Compilation is controlled by its own Kconfig symbol CHARLCD, which is to
be selected by its users, but can be enabled manually for
compile-testing.
All functions changed their prefix from "lcd_" to "charlcd_", and gained
a "struct charlcd *" parameter to operate on a specific instance.
While the driver API thus is ready to support multiple instances, the
current limitation of a single display (/dev/lcd has a single misc minor
assigned) is retained.
No functional changes intended.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OF device table must be terminated, otherwise we'll be walking past it
and into areas unknown.
Fixes: 0cad855fbd ("auxdisplay: img-ascii-lcd: driver for simple ASCII...")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no need for the driver to use private workqueue, standard system
workqueue should suffice as they are going to use the same worker pool
anyway.
Acked-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes following issues in input device (keypad) handling:
- requesting IRQ before allocating and initializing parts of the device
that can be referenced from IRQ handler is racy, even if we try to
disable interrupt after requesting it. Let's move allocations around
so that everything is ready by the time we request IRQ.
- using threaded interrupt handler to schedule a work item it sub-optimal.
Disabling and then re-enabling interrupts in work item and in open/close
methods is prone to races and exactly the reason theraded interrupts were
introduced. Let's use the infrastructure properly and keep scanning the
matrix array in IRQ thread, stopping when there are no keys, or when told
to do so.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'fbdev' is allocated as part of larger ht16k33_priv structure; trying to
free it will cause troubles.
Acked-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The new driver caused a rare randconfig failure:
drivers/auxdisplay/ht16k33.o:(.data.ht16k33_fb_ops+0xc): undefined reference to `fb_sys_read'
drivers/auxdisplay/ht16k33.o:(.data.ht16k33_fb_ops+0x10): undefined reference to `fb_sys_write'
This selects the respective helper modules.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Added a driver for the Holtek HT16K33 LED controller with keyscan.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
CC: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a driver for simple ASCII LCD displays found on the MIPS Boston,
Malta & SEAD3 development boards. The Boston display is an independent
memory mapped device with a simple memory mapped 8 byte register space
containing the 8 ASCII characters to display. The Malta display is
exposed as part of the Malta board registers, and provides 8 registers
each of which corresponds to one of the ASCII characters to display. The
SEAD3 display is slightly more complex, exposing an interface to an
S6A0069 LCD controller via registers provided by the boards CPLD.
However although the displays differ in their register interface, we
require similar functionality on each board so abstracting away the
differences within a single driver allows us to share a significant
amount of code & ensure consistent behaviour.
The driver displays the Linux kernel version as the default message, but
allows the message to be changed via a character device. Messages longer
then the number of characters that the display can show will scroll.
This provides different behaviour to the existing LCD display code for
the MIPS Malta or MIPS SEAD3 platforms in the following ways:
- The default string to display is not "LINUX ON MALTA" or "LINUX ON
SEAD3" but "Linux" followed by the version number of the kernel
(UTS_RELEASE).
- Since that string tends to be significantly longer it scrolls twice
as fast, moving every 500ms rather than every 1s.
- The LCD won't be updated until the driver is probed, so it doesn't
provide the early "LINUX" string.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14062/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The local variable ks0108_parport is used by other functions to write to
the parallel port. We missed initializing it when we converted the
driver to use new Parallel Port codes.
Fixes: 4edd70c133 ("auxdisplay: ks0108: use new parport device model")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify auxdisplay driver to use the new parallel port device model.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using min_t() is preffered than using min().
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Start using pr_* macros instead of using printk and in the process
define pr_fmt.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parport_find_base() will implicitly do parport_get_port() which
increases the refcount. Then parport_register_device() will again
increment the refcount. But while unloading the module we are only
doing parport_unregister_device() decrementing the refcount only once.
We add an parport_put_port() to neutralize the effect of
parport_get_port().
Cc: <stable@vger.kernel.org> # 2.6.32+
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Neaten and shorten the code using the new fb_<level> macros.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a two section mismatches and makes remove() __devexit.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
A pointer to cfag12864bfb_probe is passed to the core via
platform_driver_register and so the function must not disappear when the
.init sections are discarded. Otherwise (if also having HOTPLUG=y)
unbinding and binding a device to the driver via sysfs will result in an
oops as does a device being registered late.
An alternative to this patch is using platform_driver_probe instead of
platform_driver_register plus removing the pointer to the probe function
from the struct platform_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Avuton Olrich <avuton@gmail.com>
Cc: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove PARPORT dependency for Auxiliary Display support.
This is not needed since the dependency for the KS0108 driver is
PARPORT_PC.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use BUILD_BUG_ON for CFAG12864B_SIZE instead of runtime-check
- Use get_zeroed_page()
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Miguel Ojeda Sandonis <maxextreme@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This one-liner patch fixes a bug in drivers/auxdisplay/cfag12864b.c
At cfag12864b_init(), the driver tries to kalloc some memory in the
variable cfag12864b_cache.
Then, as usual, it checks if the call failed. However, it checks
cfag12864b_buffer instead.
This patch changes the "cfag12864b_buffer" to "cfag12864b_cache" so the
correct variable is checked.
Signed-off-by: Miguel Ojeda <maxextreme@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu",
so that the user can disable all the options in that menu at once
instead of having to disable each option separately.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Acked-by: Miguel Ojeda Sandonis <maxextreme@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because the framebuffer memory is allocated system RAM, use the sys_ drawing
libraries. It also fixes the following compile error:
LD .tmp_vmlinux1
drivers/built-in.o:(.data+0x8b48): undefined reference to `cfb_fillrect'
drivers/built-in.o:(.data+0x8b50): undefined reference to `cfb_copyarea'
drivers/built-in.o:(.data+0x8b58): undefined reference to `cfb_imageblit'
[adaplas]
Use fb_sys_read/write for the same reasons as above.
Signed-off-by: Avuton Olrich <avuton@gmail.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refine some depends statements to limit their visibility to the
environments that are actually supported.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The problem comes when ks0108/cfag12864b are built-in and no parallel port is
present. ks0108_init() is called first, as it should be, but fails to load
(as there is no parallel port to use).
After that, cfag12864b_init() gets called, without knowing anything about
ks0108 failed, and calls ks0108_writecontrol(), which dereferences an
uninitialized pointer.
Init order is OK, I think. The problem is how to stop cfag12864b_init() being
called if ks0108 failed to load. modprobe does it for us, but, how when
built-in?
Signed-off-by: Miguel Ojeda Sandonis <maxextreme@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for auxiliary displays, the ks0108 LCD controller, the
cfag12864b LCD and adds a framebuffer device: cfag12864bfb.
- Add a "auxdisplay/" folder in "drivers/" for auxiliary display
drivers.
- Add support for the ks0108 LCD Controller as a device driver. (uses
parport interface)
- Add support for the cfag12864b LCD as a device driver. (uses ks0108
LCD Controller driver)
- Add a framebuffer device called cfag12864bfb. (uses cfag12864b LCD
driver)
- Add the usual Documentation, includes, Makefiles, Kconfigs,
MAINTAINERS, CREDITS...
- Miguel Ojeda will maintain all the stuff above.
[rdunlap@xenotime.net: workqueue fixups]
[akpm@osdl.org: kconfig fix]
Signed-off-by: Miguel Ojeda Sandonis <maxextreme@gmail.com>
Cc: Greg KH <greg@kroah.com>
Acked-by: Paulo Marques <pmarques@grupopie.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Meyer