Instead of calculating the offloads counters, count them explicitly.
The calculations done for these counters would result in bugs in some
cases, for example:
When running TCP traffic over a VXLAN tunnel with TSO enabled the following
counters would increase:
tx_csum_partial: 1,333,284
tx_csum_partial_inner: 29,286
tx4_csum_partial_inner: 384
tx7_csum_partial_inner: 8
tx9_csum_partial_inner: 34
tx10_csum_partial_inner: 26,807
tx11_csum_partial_inner: 287
tx12_csum_partial_inner: 27
tx16_csum_partial_inner: 6
tx25_csum_partial_inner: 1,733
Seems like tx_csum_partial increased out of nowhere.
The issue is in the following calculation in mlx5e_update_sw_counters:
s->tx_csum_partial = s->tx_packets - tx_offload_none - s->tx_csum_partial_inner;
While tx_packets increases by the number of GSO segments for each SKB,
tx_csum_partial_inner will only increase by one, resulting in wrong
tx_csum_partial counter.
Fixes: bfe6d8d1d4 ("net/mlx5e: Reorganize ethtool statistics")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use the correct formatting for netdev features.
Fixes: 0e405443e8 ("net/mlx5e: Improve set features ndo resiliency")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
- Lots of hfi1 driver updates (mixed with a few qib and core updates as
well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so we
can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@
-----BEGIN PGP SIGNATURE-----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=2ntC
-----END PGP SIGNATURE-----
Merge tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a big pull request.
Of note is that I'm sending you the new ioctl API for the rdma
subsystem. We put it up on linux-api@, but didn't get much response.
The API is complex, but it solves two different problems in one go:
1) The bi-directional nature of the RDMA file write calls, which
created the security hole we had to handle (and for which the fix
is now causing problems for systems in production, we were a bit
over zealous in the fix and the ability to open a device, then
fork, then create new queue pairs on the device and use them is
broken).
2) The bloat caused by different vendors implementing extensions to
the base verbs API. Each vendor's hardware is slightly different,
and the hardware might be suitable for one extension but not
another.
By the time we add generic extensions for all the different ways
that the different hardware can offload things, the API becomes
bloated. Things like our completion structs have started to exceed
a cache line in size because of all the elements needed to support
this. That in turn shows up heavily in the performance graphs with
a noticable drop in performance on 100Gigabit links as our
completion structs go from occupying one cache line to 1+.
This API makes things like the completion structs modular in a
very similar way to netlink so that your structs can only include
the items needed for the offloads/features you are actually using
on a given queue pair. In that way we support everything, but only
use what we need, and our structs stay smaller.
The ioctl API is better explained by the posting on linux-api@ than I
can explain it here, so I'll just leave it at that.
The rest of the pull request is typical stuff.
Updates for 4.14 kernel merge window
- Lots of hfi1 driver updates (mixed with a few qib and core updates
as well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so
we can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@"
* tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (328 commits)
IB/core: Expose ioctl interface through experimental Kconfig
IB/core: Assign root to all drivers
IB/core: Add completion queue (cq) object actions
IB/core: Add legacy driver's user-data
IB/core: Export ioctl enum types to user-space
IB/core: Explicitly destroy an object while keeping uobject
IB/core: Add macros for declaring methods and attributes
IB/core: Add uverbs merge trees functionality
IB/core: Add DEVICE object and root tree structure
IB/core: Declare an object instead of declaring only type attributes
IB/core: Add new ioctl interface
RDMA/vmw_pvrdma: Fix a signedness
RDMA/vmw_pvrdma: Report network header type in WC
IB/core: Add might_sleep() annotation to ib_init_ah_from_wc()
IB/cm: Fix sleeping in atomic when RoCE is used
IB/core: Add support to finalize objects in one transaction
IB/core: Add a generic way to execute an operation on a uobject
Documentation: Hardware tag matching
IB/mlx5: Support IB_SRQT_TM
net/mlx5: Add XRQ support
...
In default, uniformly distribute the RSS indirection table entries
among all RX rings, rather than restricting this only to the rings
on the close NUMA node. irqbalancer would anyway dynamically override
the default affinities set to the RX rings.
This gives better multi-stream performance and CPU util.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
NAPI context keeps rescheduling on same CPU as long as it's busy.
This doesn't give the oppurtunity for changes in irq affinities
to take effect.
Fix that by calling napi_complete_done() upon a change in affinity.
This would stop the NAPI and reschedule it on the new CPU.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We used a channel state bit MLX5E_CHANNEL_NAPI_SCHED to make
sure no NAPI is missed when a channel's napi_schedule() is called
for completion events of the different channel's resources/rings
while NAPI is currently running.
Now, as similar mechanism is implemented in kernel,
("39e6c8208d7b net: solve a NAPI race"),
we obsolete our own implementation and rely on the return value
of napi_complete_done().
This patch removes a redundant overhead of atomic bit operations.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Avoid recycling an RX page if it moved to another NUMA node.
Add an ethtool counter to count such events.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
As of current design, in each NAPI, only a single UMR WQE
completion could be available in the completion queue of the
the internal control operations (ICO) send queue, in addition
to nop operations that require no actions upon completion.
This renders the consume index obsolete, as the wqe_counter
field in CQE is sufficient.
This helps removing a memory barrier, and obsoletes the need
for tracking the num_wqebbs to update the consumer counter.
In addition, remove other unused fields in icosq struct:
pdev, dma_fifo_pc, and prev_cc.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Separate the RX post WQEs function of the different RQ types.
This enables RQ type-specific optimizations in data-path.
Poll the ICOSQ completion queue only for Striding RQ,
and only when a UMR post completion could be possibly available.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The indication for a UMR WQE in progress is needed only within
the NAPI context, and hence no races possible and no need for
the use of atomic operations.
The only place the flag is read outside of NAPI context is
in closure flow, after RQ is disabled flag is no more accessed
in NAPI.
Use a boolean instead of a bit in ring state, so that its
non-atomic set operations do not race with the atomic sets of
the other bits.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Rings enabled state change occurs in control path only, and is always
followed by a napi_sychronize(), so that following NAPIs read the
new value. This read does not need to be atomic.
The RQ auto-moderation bit is not set/cleared in data-path.
No need for atomic read, a regular read operation is sufficient.
In RQ creation time as well, there's no multiple threads trying
to access it yet, hence a regular read can be used.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The dma offset of a MPWQE (Multi-Packet WQE) in memory region
is fixed for all rounds. Calculate it once on creation time,
instead of in runtime. This also obsoletes the wqe argument in
the function.
In addition, optimize dma_info iterator calculation.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Field is used only locally within the RQ create function.
The use of a local variable is sufficient.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In RX data-path, use shift operations instead of a regular multiplication
by stride size, as it is a power of two.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Bring fast-path fields together, and combine RX WQE mutual
exclusive fields into a union.
Page-reuse and XDP are mutually exclusive and cannot be used at
the same time.
Use a union to combine their footprints.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce a new flow table and indirect TIRs which are used to hash the
inner packet headers of GRE tunneled packets.
When a GRE tunneled packet is received, the TTC flow table will match
the new IPv4/6->GRE rules which will forward it to the inner TTC table.
The inner TTC is similar to its counterpart outer TTC table, but
matching the inner packet headers instead of the outer ones (and does
not include the new IPv4/6->GRE rules).
The new rules will not add steering hops since they are added to an
already existing flow group which will be matched regardless of this
patch. Non GRE traffic will not be affected.
The inner flow table will forward the packet to inner indirect TIRs
which hash the inner packet and thus result in RSS for the tunneled
packets.
Testing 8 TCP streams bandwidth over GRE:
System: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
NIC: Mellanox Technologies MT28800 Family [ConnectX-5 Ex]
Before: 21.3 Gbps (Single RQ)
Now : 90.5 Gbps (RSS spread on 8 RQs)
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add TX offloads support for GRE tunneled packets by reporting the needed
netdev features.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
cq_period_mode assignment was mistakenly removed so it was always set to "0",
which is EQE based moderation, regardless of the device CAPs and
requested value in ethtool.
Fixes: 6a9764efb2 ("net/mlx5e: Isolate open_channels from priv->params")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
rx_buffer_passed_thres_phy - The number of events where the port RX
buffer has passed a fullness threshold.
rx_buffer_full_phy - The number of events where the port RX buffer has
reached 100% fullness.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Upon interface up/down, driver will send PAOS (Ports Administrative and
Operational Status Register) in order to inform the Firmware on the
desired status of the port by the driver.
Since now we might change physical link status on mlx5e_open/close,
logical VF representor should not use mlx5e_open/close ndos as is, and
should call the logical version mlx5e_open/closed_locked.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The offending commit used a newly added helper function.
But the logic is wrong. Without this fix, the affected NICs
can't do HW offload. Error -EOPNOTSUPP will be returned directly.
Fixes: a2e8da9378 ("net/sched: use newly added classid identity helpers")
Signed-off-by: Chris Mi <chrism@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of checking handle, which does not have the inner class
information and drivers wrongly assume clsact->egress as ingress, use
the newly introduced classid identification helpers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
generic api takes care of spreading affinity similar to
what mlx5 open coded (and even handles better asymmetric
configurations). Ask the generic API to spread affinity
for us, and feed him pre_vectors that do not participate
in affinity settings (which is an improvement to what we
had before).
The affinity assignments should match what mlx5 tried to
do earlier but now we do not set affinity to async, cmd
and pages dedicated vectors.
Also, remove mlx5e_get_cpu and introduce mlx5e_get_node
(used for allocation purposes) and mlx5_get_vector_affinity
(for indirection table construction) as they provide the needed
information. Luckily, we have generic helpers to get cpumask
and node given a irq vector. mlx5_get_vector_affinity will
be used by mlx5_ib in a subsequent patch.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
mlx5e currently assumes that irq affinity is really spread first
irq vectors across device home node cpus, with the new generic affinity
mappings this is no longer the case, hence mlxe should not rely on
this anymore.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Now that we have a generic code to allocate an array
of irq vectors and even correctly spread their affinity,
correctly handle cpu hotplug events and more, were much
better off using it.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This series includes some mlx5 updates for both net-next and rdma trees.
From Saeed,
Core driver updates to allow selectively building the driver with
or without some large driver components, such as
- E-Switch (Ethernet SRIOV support).
- Multi-Physical Function Switch (MPFs) support.
For that we split E-Switch and MPFs functionalities into separate files.
From Erez,
Delay mlx5_core events when mlx5 interfaces, namely mlx5_ib, registration
is taking place and until it completes.
From Rabie,
Increase the maximum supported flow counters.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZiDoAAAoJEEg/ir3gV/o+594H/RH5kRwC719s/5YQFJXvGsVC
fjtj3UUJPLrWB8XBh7a4PRcxXPIHaFKJuY3MU7KHFIeZQFklJcit3njjpxDlUINo
F5S1LHBSYBkeMD/ksWBA8OLCBprNGN6WQ2tuFfAjZlQQ44zqv8LJmegoDtW9bGRy
aGAkjUmALEblQsq81y0BQwN2/8DA8HAywrs8L2dkH1LHwijoIeYMZFOtKugv1FbB
ABSKxcU7D/NYw6rsVdZG59fHFQ+eKOspDFqBZrUzfQ+zUU2hFFo96ovfXBfIqYCV
7BtJuKXu2LeGPzFLsuw4h1131iqFT1iSMy9fEhf/4OwaL/KPP/+Umy8vP/XfM+U=
=wCpd
-----END PGP SIGNATURE-----
Merge tag 'mlx5-shared-2017-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-shared-2017-08-07
This series includes some mlx5 updates for both net-next and rdma trees.
From Saeed,
Core driver updates to allow selectively building the driver with
or without some large driver components, such as
- E-Switch (Ethernet SRIOV support).
- Multi-Physical Function Switch (MPFs) support.
For that we split E-Switch and MPFs functionalities into separate files.
From Erez,
Delay mlx5_core events when mlx5 interfaces, namely mlx5_ib, registration
is taking place and until it completes.
From Rabie,
Increase the maximum supported flow counters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let mlx5e_setup_tc (former mlx5e_ndo_setup_tc) be a splitter for specific
setup_tc types and push out cls_flower and mqprio specific codes into
separate functions. Also change the return values so they are the same
as in the rest of the drivers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to selectively build the driver with or without sriov eswitch, VF
representors and TC offloads.
Also remove the need of two ndo ops structures (sriov & basic)
and keep only one unified ndo ops, compile out VF SRIOV ndos when not
needed (MLX5_ESWITCH=n), and for VF netdev calling those ndos will result
in returning -EPERM.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Jes Sorensen <jsorensen@fb.com>
Cc: kernel-team@fb.com
Expose MLX5_VPORT_MANAGER macro to check for strict vport manager
E-switch and MPFS (Multi Physical Function Switch) abilities.
VPORT manager must be a PF with an ethernet link and with FW advertised
vport group manager capability
Replace older checks with the new macro and use it where needed in
eswitch.c and mlx5e netdev eswitch related flows.
The same macro will be reused in MPFS separation downstream patch.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Remove redundant call to unregister vport representor in mlx5e_add error
flow.
Hide the representor priv and eswitch internal structures from en_main.c
as preparation step for downstream patches which would allow building
the driver without support for representors and eswitch.
Fixes: 6f08a22c5f ("net/mlx5e: Register/unregister vport representors on interface attach/detach")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Since we are going to allow building the driver without eswitch support,
it would be possible to compile out the sriov netdevice ops struct such
that the basic ops instance will be used for non VF devices too.
Add missing udp tunnel ndos into mlx5e_netdev_ops_basic.
While here, rearrange some ndos in the sriov ops struct and put
vf/eswitch related ndos towards the end of it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Add the missing option to enable the PTP_CLK_PPS function.
In this case pin should be configured as 1PPS IN first and
then it will be connected to PPS mechanism.
Events will be reported as PTP_CLOCK_PPSUSR events to relevant sysfs.
Fixes: ee7f12205a ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Some overlapping changes in the mlx5 driver.
A merge conflict resolution posted by Stephen Rothwell was used as a
guide.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the TX data path, prepend a special metadata ethertype which
instructs the hardware to perform cryptography.
In addition, fill Software-Parser segment in TX descriptor so
that the hardware may parse the ESP protocol, and perform TX
checksum offload on the inner payload.
Support GSO, by providing the inverse of gso_size in the metadata.
This allows the FPGA to update the ESP header (seqno and seqiv) on the
resulting packets, by calculating the packet number within the GSO
back from the TCP sequence number.
Note that for GSO SKBs, the stack does not include an ESP trailer,
unlike the non-GSO case.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In RX data path, the hardware prepends a special metadata ethertype
which indicates that the packet underwent decryption, and the result of
the authentication check.
Communicate this to the stack in skb->sp.
Make wqe_size large enough to account for the injected metadata.
Support only Linked-list RQ type.
IPSec offload RX packets may have useful CHECKSUM_COMPLETE information,
which the stack may not be able to use yet.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add Innova IPSec ESP crypto offload configuration paths.
Detect Innova IPSec device and set the NETIF_F_HW_ESP flag.
Configure Security Associations using the API introduced in a previous
patch.
Add Software-parser hardware descriptor layout
Software-Parser (swp) is a hardware feature in ConnectX which allows the
host software to specify protocol header offsets in the TX path, thus
overriding the hardware parser.
This is useful for protocols that the ASIC may not be able to parse on
its own.
Note that due to inline metadata, XDP is not supported in Innova IPSec.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Symbol error during carrier counter from PPCNT was mistakenly reported as
TX carrier errors in get_stats ndo, although it's an RX counter.
Fixes: 269e6b3af3 ("net/mlx5e: Report additional error statistics in get stats ndo")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce a Page-Reuse mechanism in non-Striding RQ RX datapath.
A WQE (RX descriptor) buffer is a page, that in most cases was fully
wasted on a packet that is much smaller, requiring a new page for
the next round.
In this patch, we implement a page-reuse mechanism, that resembles a
`SW Striding RQ`.
We allow the WQE to reuse its allocated page as much as it could,
until the page is fully consumed. In each round, the WQE is capable
of receiving packet of maximal size (MTU). Yet, upon the reception of
a packet, the WQE knows the actual packet size, and consumes the exact
amount of memory needed to build a linear SKB. Then, it updates the
buffer pointer within the page accordingly, for the next round.
Feature is mutually exclusive with XDP (packet-per-page)
and LRO (session size is a power of two, needs unused page).
Performance tests:
iperf tcp tests show huge gain:
--------------------------------------------
num streams | BW before | BW after | ratio |
1 | 22.2 | 30.9 | 1.39x |
8 | 64.2 | 93.6 | 1.46x |
64 | 56.7 | 91.4 | 1.61x |
--------------------------------------------
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In the RX memory scheme of non Striding RQ, we use linear SKBs.
Keeping NET_IP_ALIGN in headroom can improve performance on some archs.
In addition, take this headroom into account when calculating the
LRO WQE size.
These are not needed in Striding RQ as they're done implicitly
within the non-linear SKB allocation.
Fixes: 1bfecfca56 ("net/mlx5e: Build RX SKB on demand")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Build the SKB over the receive packet instead of the
whole page. Getting the SKB's linear data and shared_info
closer improves locality.
In addition, this opens up the possibility to make use of
other parts of the page in the downstream page-reuse patch.
Fixes: 1bfecfca56 ("net/mlx5e: Build RX SKB on demand")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ioctl support to IPoIB device driver. For now, this
ioctl will support timestamp get and set.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Eitan Rabin <rabin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The mtu extra space that kept for the HW is specific for each link type,
and it is different in mlx5e and mlx5i modules.
Now it is kept in the priv structures, set by the mlx5e/mlx5i driver
accordingly.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Updating the carrier involves specific HW setting, each profile should
use its own function for that.
Both IPoIB and VF representor don't need carrier update function, since
VF representor has only a logical link to VF and IPoIB manages its own
link via ib_core upper layer.
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Gal Pressman