* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (21 commits)
ARM: OMAP4: MMC: increase delay for pbias
arm: omap2plus: move NAND_BLOCK_SIZE out of boards
omap4: hwmod: Enable the keypad
omap3: Free Beagle rev gpios when they are read, so others can read them later
arm: omap3: beagle: Ensure msecure is mux'd to be able to set the RTC
omap: rx51: Don't power up speaker amplifier at bootup
omap: rx51: Set regulator V28_A always on
ARM: OMAP4: MMC: no regulator off during probe for eMMC
arm: omap2plus: fix ads7846 pendown gpio request
ARM: OMAP2: Add missing iounmap in omap4430_phy_init
ARM: omap4: Pass core and wakeup mux tables to omap4_mux_init
ARM: omap2+: mux: Allow board mux settings to be NULL
OMAP4: fix return value of omap4_l3_init
OMAP: iovmm: fix SW flags passed by user
arch/arm/mach-omap1/dma.c: Invert calls to platform_device_put and platform_device_del
OMAP2+: mux: fix compilation warnings
OMAP: SRAM: Fix warning: format '%08lx' expects type 'long unsigned int'
arm: omap3: cm-t3517: fix section mismatch warning
OMAP2+: Fix 9 section mismatch(es) warnings from mach-omap2/built-in.o
ARM: OMAP2: Add missing include of linux/gpio.h
...
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
vfs: make unlink() and rmdir() return ENOENT in preference to EROFS
lmLogOpen() broken failure exit
usb: remove bad dput after dentry_unhash
more conservative S_NOSEC handling
Semicolons are not necessary after switch/while/for/if braces
so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices that can generate interrupts are connected directly to the
CPU through the bootbus on sun4d. This patch allows IRQs to be allocated
for such devices. The information used for allocating interrupts for
sbus devices are present at the corresponding SBI node. For bootbus
devices this information is present in the bootbus node.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the introduction of genirq on sparc32 bugs were introduced in
the interrupt handler for sun4d. The interrupts handler checks the status
of the various sbus interfaces in the system and generates a virtual
interrupt, based upon the location of the interrupt source. This lookup
was broken by restructuring the code in such a way that index and shift
operations were performed prior to comparing this against the values
read from the interrupt controllers.
This could cause the handler to loop eternally as the interrupt source
could be skipped before any check was performed. Additionally
sun4d_encode_irq performs shifting internally, so it should not be performed
twice.
In sun4d_unmask interrupts were not correctly acknowledged, as the
corresponding bit it the interrupt mask was not actually cleared.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sun4d_build_device_irq was called without a valid platform_device when
the system timer was initialized on sun4d systems. This caused a NULL
pointer crash.
Josip Rodin suggested that the current sun4d_build_device_irq should be
split into two functions. So that the timer initialization could skip
the slot and sbus interface detection code in sun4d_build_device_irq, as
this does not make sence due to the timer interrupts not being generated
from a device located on sbus.
Signed-off-by: Kjetil Oftedal <oftedal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a559d2c8c1.
Turns out that device id 0x1d6b:0x0002 is a USB hub, which causes havoc
when the option driver tries to bind to it.
So revert this as it doesn't seem to be needed at all.
Thanks to Michael Tokarev and Paweł Drobek for working on resolving this
issue.
Cc: Paweł Drobek <pawel.drobek@gmail.com>
Cc: Michael Tokarev <mjt@tls.msk.ru>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The loops over connection ID strings in pm_runtime_clk_notify()
should actually iterate over the strings and not over the elements
of the first of them, so make them behave as appropriate.
This fixes a regression introduced by commit 600b776eb3
(OMAP1 / PM: Use generic clock manipulation routines for runtime PM).
Reported-and-tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
When SR-IOV is enabled, i350 devices fail to pass traffic. This is due to
the driver attempting to enable RSS on the PF device, which is not
supported by the i350.
When max_vfs is specified on an i350 adapter, set the number of RSS queues
to 1.
This issue affects 2.6.39 as well.
CC: stable@kernel.org
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Samsung GPIO drivers are always built-in when the relevant
platform is selected. Â Change the Kconfig symbol to def_bool y
dependant on the platform.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
To work around controllers which can't properly plug events while
reset, ata_eh_reset() clears error states and ATA_PFLAG_EH_PENDING
after reset but before RESET is marked done. As reset is the final
recovery action and full verification of devices including onlineness
and classfication match is done afterwards, this shouldn't lead to
lost devices or missed hotplug events.
Unfortunately, it forgot to thaw the port when clearing EH_PENDING, so
if the condition happens after resetting an empty port, the port could
be left frozen and EH will end without thawing it, making the port
unresponsive to further hotplug events.
Thaw if the port is frozen after clearing EH_PENDING. This problem is
reported by Bruce Stenning in the following thread.
http://thread.gmane.org/gmane.linux.kernel/1123265
stable: I think we should weather this patch a bit longer in -rcX
before sending it to -stable. Please wait at least a month
after this patch makes upstream. Thanks.
-v2: Fixed spelling in the comment per Dave Howorth.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Bruce Stenning <b.stenning@indigovision.com>
Cc: stable@kernel.org
Cc: Dave Howorth <dhoworth@mrc-lmb.cam.ac.uk>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If CONFIG_PM is not set, init_iommu_pm_ops() introduced by commit
134fac3f45 (PCI / Intel IOMMU: Use
syscore_ops instead of sysdev class and sysdev) is not defined
appropriately. Fix this issue.
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The data pointer should be freed in the error
cases of adis16400_trigger_handler().
Signed-off-by: Andre Bartke <andre.bartke@gmail.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Many Linux distributions would enable vesafb in order to display
early stage boot splash. In this case, we will get garbled X
Window screen if running X fbdev on psbfb.
This is because fb0 is occupied by vesafb while psbfb is on fb1.
They tried to drive the same pieces of hardware at the same
time. With unmodified X start-up, it would try to use default
fb0 framebuffer device and unfortunately it is now broken
becaues fb1 supersedes it.
We should let psbfb takeover framebuffer control from vesafb
to get around this problem.
See also commit : 4410f39109
Signed-off-by: Michael Chang <mchang@novell.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the Fit-PC2 the VBT reports an invalid fixed panel mode for LVDS, this gets
in the way for SDVO. This patch makes VBT parsing skip the invalid mode. When
there is no LVDS output the backlight support crashes so the patch also checks
for this before enabling it.
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Implemented pre_reset and post_reset methods of the driver to prevent the
driver from being unbound upon a device reset. Because of this also the
asynchronous reset introduced to prevent a race condition is no longer necessary
(and sometimes causes problems, because it comes later then expected).
Signed-off-by: Arjan Mels <arjan.mels@gmx.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Takahiro Hirofuchi <hirofuchi@users.sourceforge.net>
Cc: Max Vozeler <max@vozeler.com>
Cc: usbip-devel <usbip-devel@lists.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Failure to set iio_poll_func private_data, causes zero pointer access
violations in all consumer trigger handlers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Looks like a typo.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build errors when CONFIG_CFG80211 is not enabled:
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b71): undefined reference to `cfg80211_scan_done'
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b86): undefined reference to `wiphy_unregister'
drivers/built-in.o: In function `ar6k_cfg80211_deinit':
(.text+0x189b8d): undefined reference to `wiphy_free'
drivers/built-in.o: In function `ar6k_cfg80211_init':
(.text+0x18add7): undefined reference to `wiphy_new'
drivers/built-in.o: In function `ar6k_cfg80211_init':
(.text+0x18ae48): undefined reference to `wiphy_register'
drivers/built-in.o: In function `ar6k_cfg80211_tkip_micerr_event':
(.text+0x18ae95): undefined reference to `cfg80211_michael_mic_failure'
drivers/built-in.o: In function `ar6k_cfg80211_scan_node':
(.text+0x18afb5): undefined reference to `__ieee80211_get_channel'
drivers/built-in.o: In function `ar6k_cfg80211_scan_node':
(.text+0x18afd2): undefined reference to `cfg80211_inform_bss_frame'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b046): undefined reference to `cfg80211_ibss_joined'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b176): undefined reference to `cfg80211_connect_result'
drivers/built-in.o: In function `ar6k_cfg80211_disconnect_event':
(.text+0x18b190): undefined reference to `cfg80211_disconnected'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b291): undefined reference to `cfg80211_get_bss'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b457): undefined reference to `cfg80211_put_bss'
drivers/built-in.o: In function `ar6k_cfg80211_connect_event':
(.text+0x18b4fa): undefined reference to `cfg80211_roamed'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Luis R. Rodriguez <mcgrof@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Naveen Singh <nsingh@atheros.com>
Signed-off-by: Peter Foley <pefoley2@verizon.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix olpc_dcon.c build by selecting the needed kconfig symbol
BACKLIGHT_CLASS_DEVICE.
olpc_dcon.c:(.text+0x11588b): undefined reference to `backlight_device_register'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andres Salomon <dilinger@queued.net>
Cc: Chris Ball <cjb@laptop.org>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Part of the requirement to be in the staging tree is that the code must
build, so let's make it easier for people to build the code to
test/prove this out.
Based on a recommendation from Linus to implement this.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Staging drivers should be self-contained, without files in the include/
directories. So move the altera.h file back to the driver directory for
now, until it moves out of the staging tree.
Cc: Igor M. Liplianin <liplianin@netup.ru>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revert the commit that removed the disabling of interrupts around
the initial modifying of mcount callers to nops, and update the comment.
The original comment was outdated and stated that the interrupts were
being disabled to prevent kstop machine, which was required with the
old ftrace daemon, but was no longer the case.
What the comment failed to mention was that interrupts needed to be
disabled to keep interrupts from preempting the modifying of the code
and then executing the code that was partially modified.
Revert the commit and update the comment.
Reported-by: Richard W.M. Jones <rjones@redhat.com>
Tested-by: Richard W.M. Jones <rjones@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
With gcc 4.6, the self test kprobe function:
kprobe_trace_selftest_target()
is optimized such that kallsyms does not list it. The kprobes
test uses this function to insert a probe and test it. But
it will fail the test if the function is not listed in kallsyms.
Adding a __used annotation keeps the symbol in the kallsyms table.
Suggested-by: David Daney <ddaney@caviumnetworks.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When one of the SSID's length passed in a scan or sched_scan request
is larger than 255, there will be an overflow in the u8 that is used
to store the length before checking. This causes the check to fail
and we overrun the buffer when copying the SSID.
Fix this by checking the nl80211 attribute length before copying it to
the struct.
This is a follow up for the previous commit
208c72f4fe, which didn't fix the problem
entirely.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the case we fail to allocate a new skb, the old skb should
be resubmitted unmodified.
Fixes bug introduced in a9e1286975.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Should pass along packet if there's no CRC and no hardware error.
Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 1d38c16ce4.
The mac80211 maintainer raised complaints about abuse of the CSA stop
reason, and about whether this patch actually serves its intended
purpose at all.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The S3C_GPIO_PULL_UP macro value incorrectly maps to a reserved setting of GPIO
pull up/down registers on Exynos4 platform. Fix this incorrect mapping by adding
wrappers to the s3c_gpio_setpull_updown and s3c_gpio_getpull_updown functions.
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a label before the call to clk_put and jump to that in the error
handling code that occurs after the call to clk_get has succeeded.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2;
statement S;
@@
e1 = clk_get@p1(...);
... when != e1 = e2
when != clk_put(e1)
when any
if (...) { ... when != clk_put(e1)
when != if (...) { ... clk_put(e1) ... }
* return@p3 ...;
} else S
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1468) changes the Kconfig definition for
USB_GADGET_DUALSPEED. This option is determined entirely by which
device controller drivers are to be built, through Select statements;
it does not need to be (and should not be) configurable by the user.
Also, the "default n" line is superfluous -- everything defaults to N.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Like with other host controllers capable of operating at both high
speed and full speed, we need to indicate that the emulated controller
presented by dummy-hcd has this ability. Otherwise usbcore will not
accept full-speed gadgets under dummy-hcd. This patch (as1469) sets
the appropriate has_tt flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some USB mass-storage devices have bugs that cause them not to handle
the first READ(10) command they receive correctly. The Corsair
Padlock v2 returns completely bogus data for its first read (possibly
it returns the data in encrypted form even though the device is
supposed to be unlocked). The Feiya SD/SDHC card reader fails to
complete the first READ(10) command after it is plugged in or after a
new card is inserted, returning a status code that indicates it thinks
the command was invalid, which prevents the kernel from retrying the
read.
Since the first read of a new device or a new medium is for the
partition sector, the kernel is unable to retrieve the device's
partition table. Users have to manually issue an "hdparm -z" or
"blockdev --rereadpt" command before they can access the device.
This patch (as1470) works around the problem. It adds a new quirk
flag, US_FL_INVALID_READ10, indicating that the first READ(10) should
always be retried immediately, as should any failing READ(10) commands
(provided the preceding READ(10) command succeeded, to avoid getting
stuck in a loop). The patch also adds appropriate unusual_devs
entries containing the new flag.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Sven Geggus <sven-usbst@geggus.net>
Tested-by: Paul Hartman <paul.hartman+linux@gmail.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If user space attempts to remove a non-existent file or directory, and
the file system is mounted read-only, return ENOENT instead of EROFS.
Either error code is arguably valid/correct, but ENOENT is a more
specific error message.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Callers of lmLogOpen() expect it to return -E... on failure exits, which
is what it returns, except for the case of blkdev_get_by_dev() failure.
It that case lmLogOpen() return the error with the wrong sign...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Sergey reported a CONFIG_PROVE_RCU warning in push_rt_task where
set_task_cpu() was called with both relevant rq->locks held, which
should be sufficient for running tasks since holding its rq->lock
will serialize against sched_move_task().
Update the comments and fix the task_group() lockdep test.
Reported-and-tested-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1307115427.2353.3456.camel@twins
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The main lock_is_held() user is lockdep_assert_held(), avoid false
assertions in lockdep_off() sections by unconditionally reporting the
lock is taken.
[ the reason this is important is a lockdep_assert_held() in ttwu()
which triggers a warning under lockdep_off() as in printk() which
can trigger another wakeup and lock up due to spinlock
recursion, as reported and heroically debugged by Arne Jansen ]
Reported-and-tested-by: Arne Jansen <lists@die-jansens.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1307398759.2497.966.camel@laptop
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the codec_name field of the dai_link to match the actual device name
of the codec. Otherwise the card won't be instantiated.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Some PCIe cards ship with a PCI-PCIe bridge which is not
visible as a PCI device in Linux. But the device-id of the
bridge is present in the IOMMU tables which causes a boot
crash in the IOMMU driver.
This patch fixes by removing these cards from the IOMMU
handling. This is a pure -stable fix, a real fix to handle
this situation appriatly will follow for the next merge
window.
Cc: stable@kernel.org # > 2.6.32
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Frank Blaschka reported :
<quote>
During heavy network load we turn off/on cpus.
Sometimes this causes a stall on the network device.
Digging into the dump I found out following:
napi is scheduled but does not run. From the I/O buffers
and the napi state I see napi/rx_softirq processing has stopped
because the budget was reached. napi stays in the
softnet_data poll_list and the rx_softirq was raised again.
I assume at this time the cpu offline comes in,
the rx softirq is raised/moved to another cpu but napi stays in the
poll_list of the softnet_data of the now offline cpu.
Reviewing dev_cpu_callback (net/core/dev.c) I did not find the
poll_list is transfered to the new cpu.
</quote>
This patch is a straightforward implementation of Frank suggestion :
Transfert poll_list and trigger NET_RX_SOFTIRQ on new cpu.
Reported-by: Frank Blaschka <blaschka@linux.vnet.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 2.6.27, commit 393e52e33c (packet: deliver VLAN TCI to userspace)
added a small information leak.
Add padding field and make sure its zeroed before copy to user.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
BugLink: https://launchpad.net/bugs/792712
The original reporter states that sound from the internal speakers is
inaudible until using the model=auto quirk. This symptom is due to an
existing quirk mask for 0x102802b* that uses the model=dell quirk. To
limit the possible regressions, leave the existing quirk mask but add
a higher priority specific mask for the reporter's PCI SSID.
Reported-and-tested-by: rodni hipp
Cc: <stable@kernel.org> [2.6.38+]
Signed-off-by: Daniel T Chen <crimsun@ubuntu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
kernel/trace/ftrace.c: In function 'ftrace_regex_write.clone.15':
kernel/trace/ftrace.c:2743:6: warning: 'ret' may be used uninitialized in this
function
Signed-off-by: GuoWen Li <guowen.li.linux@gmail.com>
Link: http://lkml.kernel.org/r/201106011918.47939.guowen.li.linux@gmail.com
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
When signing is enabled, the first session that's established on a
socket will cause a printk like this to pop:
CIFS VFS: Unexpected SMB signature
This is because the key exchange hasn't happened yet, so the signature
field is bogus. Don't try to check the signature on the socket until the
first session has been established. Also, eliminate the specific check
for SMB_COM_NEGOTIATE since this check covers that case too.
Cc: stable@kernel.org
Cc: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
