The statistics registers have write-clear behaviour, which means we
will lose any increment between the read and write. Mitigate this by
only clearing when we read a non-zero value, so we will never falsely
report a total of zero. This also saves time as we only handle
error statistics here and they won't often be incremented.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many different sets of registers implemented by the
different versions of this controller, and we can only expect this to
get more complicated in future. Limit how much ethtool needs to know
by including an explicit bitmap of which registers are included in the
dump, allowing room for future growth in the number of possible
registers.
As I don't have datasheets for all of these, I've only included
registers that are:
- defined in all 5 register type arrays, or
- used by the driver, or
- documented in the datasheet I have
Add one new capability flag so we can tell whether the RTRATE
register is implemented.
Delete the TSU_ADRL0 and TSU_ADR{H,L}31 definitions, as they weren't
used and the address table is already assumed to be contiguous.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we may silently read/write a register at offset 0. Change
this to WARN and then ignore the write or read-back all-ones.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least on the R8A7790, RFS8 reflects the RINT8 (multicast) MAC
status flag.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
My previous fix to clear padding of short frames used skb->len as the
DMA length, assuming that skb_padto() extended skb->len to include the
padding. That isn't the case; we need to use skb_put_padto() instead.
(This wasn't immediately obvious because software padding isn't
actually needed on the R-Car H2. We could make it conditional on
which chip is being driven, but it's probably not worth the effort.)
Reported-by: "Violeta Menéndez González" <violeta.menendez@codethink.co.uk>
Fixes: 612a17a54b50 ("sh_eth: Fix padding of short frames on TX")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit fd9af07c34.
The hardware manual states that the frame error and multicast bits are
copied to bits 9:0 of RD0, not bits 25:16. I've tested that this is
true for RFS1 (CRC error), RFS3 (frame too short), RFS4 (frame too
long) and RFS8 (multicast).
Also adjust a comment to agree with this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of RX ring underrun (RDE), we attempt to reset the software
descriptor pointers (dirty_rx and cur_rx) to match where the hardware
will read the next descriptor from, as that might not be the first
dirty descriptor. This relies on reading RDFAR, but that register
doesn't exist on all supported chips - specifically, not on the R-Car
chips. This will result in unpredictable behaviour on those chips
after an RDE.
Make this pointer reset conditional and assume that it isn't needed on
the R-Car chips. This fix also assumes that RDFAR is never exposed at
offset 0 in the memory map - this is currently true, and a subsequent
commit will fix the ambiguity between offset 0 and no-offset in the
register offset maps.
Fixes: 79fba9f517 ("net: sh_eth: fix the rxdesc pointer when rx ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When submitting a DMA descriptor, the active bit must be written last.
When reading a completed DMA descriptor, the active bit must be read
first.
Add memory barriers to ensure that this ordering is maintained.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 740c7f31c0 ("sh_eth: Ensure DMA engines are stopped before
freeing buffers") added a call to sh_eth_reset() to the
sh_eth_set_ringparam() and sh_eth_close() paths.
However, setting the software reset bit(s) in the EDMR register resets
the MAC Address Registers to zero. Hence after kexec, the new kernel
doesn't detect a valid MAC address and assigns a random MAC address,
breaking DHCP.
Set the MAC address again after the reset in sh_eth_dev_exit() to fix
this.
Tested on r8a7740/armadillo (GETHER) and r8a7791/koelsch (FAST_RCAR).
Fixes: 740c7f31c0 ("sh_eth: Ensure DMA engines are stopped before freeing buffers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the return value of dma_map_single(), rather than calling
virt_to_page() separately
- Check for mapping failue
- Call dma_unmap_single() rather than dma_sync_single_for_cpu()
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
dma_map_single() may fail if an IOMMU or swiotlb is in use, so
we need to check for this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we try to clear EDRRR and EDTRR and immediately continue to
free buffers. This is unsafe because:
- In general, register writes are not serialised with DMA, so we still
have to wait for DMA to complete somehow
- The R8A7790 (R-Car H2) manual states that the TX running flag cannot
be cleared by writing to EDTRR
- The same manual states that clearing the RX running flag only stops
RX DMA at the next packet boundary
I applied this patch to the driver to detect DMA writes to freed
buffers:
> --- a/drivers/net/ethernet/renesas/sh_eth.c
> +++ b/drivers/net/ethernet/renesas/sh_eth.c
> @@ -1098,7 +1098,14 @@ static void sh_eth_ring_free(struct net_device *ndev)
> /* Free Rx skb ringbuffer */
> if (mdp->rx_skbuff) {
> for (i = 0; i < mdp->num_rx_ring; i++)
> + memcpy(mdp->rx_skbuff[i]->data,
> + "Hello, world", 12);
> + msleep(100);
> + for (i = 0; i < mdp->num_rx_ring; i++) {
> + WARN_ON(memcmp(mdp->rx_skbuff[i]->data,
> + "Hello, world", 12));
> dev_kfree_skb(mdp->rx_skbuff[i]);
> + }
> }
> kfree(mdp->rx_skbuff);
> mdp->rx_skbuff = NULL;
then ran the loop:
while ethtool -G eth0 rx 128 ; ethtool -G eth0 rx 64; do echo -n .; done
and 'ping -f' toward the sh_eth port from another machine. The
warning fired several times a minute.
To fix these issues:
- Deactivate all TX descriptors rather than writing to EDTRR
- As there seems to be no way of telling when RX DMA is stopped,
perform a soft reset to ensure that both DMA enginess are stopped
- To reduce the possibility of the reset truncating a transmitted
frame, disable egress and wait a reasonable time to reach a
packet boundary before resetting
- Update statistics before resetting
(The 'reasonable time' does not allow for CS/CD in half-duplex
mode, but half-duplex no longer seems reasonable!)
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If RX traffic is overflowing the FIFO or DMA ring, logging every time
this happens just makes things worse. These errors are visible in the
statistics anyway.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to stop the RX path accessing the RX ring while it's being
stopped or resized, we clear the interrupt mask (EESIPR) and then call
free_irq() or synchronise_irq(). This is insufficient because the
interrupt handler or NAPI poller may set EESIPR again after we clear
it. Also, in sh_eth_set_ringparam() we currently don't disable NAPI
polling at all.
I could easily trigger a crash by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
and 'ping -f' toward the sh_eth port from another machine.
To fix this:
- Add a software flag (irq_enabled) to signal whether interrupts
should be enabled
- In the interrupt handler, if the flag is clear then clear EESIPR
and return
- In the NAPI poller, if the flag is clear then don't set EESIPR
- Set the flag before enabling interrupts in sh_eth_dev_init() and
sh_eth_set_ringparam()
- Clear the flag and serialise with the interrupt and NAPI
handlers before clearing EESIPR in sh_eth_close() and
sh_eth_set_ringparam()
After this, I could run the loop for 100,000 iterations successfully.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the device is down then no packet buffers should be allocated.
We also must not touch its registers as it may be powered off.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must only ever stop TX queues when they are full or the net device
is not 'ready' so far as the net core, and specifically the watchdog,
is concerned. Otherwise, the watchdog may fire *immediately* if no
packets have been added to the queue in the last 5 seconds.
What's more, sh_eth_tx_timeout() will likely crash if called while
we're resizing the TX ring.
I could easily trigger this by running the loop:
while ethtool -G eth0 rx 128 && ethtool -G eth0 rx 64; do echo -n .; done
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an skb to be transmitted is shorter than the minimum Ethernet frame
length, we currently set the DMA descriptor length to the minimum but
do not add zero-padding. This could result in leaking sensitive
data. We also pass different lengths to dma_map_single() and
dma_unmap_single().
Use skb_padto() to pad properly, before calling dma_map_single().
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sh_eth_{suspend|resume}() implementing {suspend|resume|freeze|thaw|poweroff|
restore}() PM methods to make it possible to restore from hibernation not only
in Linux but also in e.g. U-Boot and to have more determined state on resume/
restore.
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
[Sergei: moved sh_eth_{suspend|resume}() before sh_eth_runtime_nop(), enclosed
them with #ifdef CONFIG_PM_SLEEP, reordered the local variables, got rid of
*goto* and label, reordered macro invocations, renamed, modified the changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use SET_RUNTIME_PM_OPS() macro to initialize the runtime PM method pointers in
the 'struct dev_pm_ops'.
Signed-off-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
[Sergei: renamed, added the changelog.]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver connects and disconnects the PHY device whenever the
net device is brought up and down. The ethtool get_settings,
set_settings and nway_reset operations will dereference a null
or dangling pointer if called while it is down.
I think it would be preferable to keep the PHY connected, but there
may be good reasons not to.
As an immediate fix for this bug:
- Set the phydev pointer to NULL after disconnecting the PHY
- Change those three operations to return -ENODEV while the PHY is
not connected
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently net_device_ops::set_rx_mode is only implemented for
chips with a TSU (multiple address table). However we do need
to turn the PRM (promiscuous) flag on and off for other chips.
- Remove the unlikely() from the TSU functions that we may safely
call for chips without a TSU
- Make setting of the MCT flag conditional on the tsu capability flag
- Rename sh_eth_set_multicast_list() to sh_eth_set_rx_mode() and plumb
it into both net_device_ops structures
- Remove the previously-unreachable branch in sh_eth_rx_mode() that
would otherwise reset the flags to defaults for non-TSU chips
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "unsigned long" by "u32" when handling 32-bit register data.
A.o., this saves 11 * 36 bytes in the static sh_eth_cpu_data structures
when compiling for 64-bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b284fbe3b3 ("sh_eth: Fix access to TRSCER register") wanted
to add a .trscer_err_mask value to the R-Car Gen2 family-specific data
structure (r8a779x_data), but it was accidentally added to the
SH7724-specific data structure (sh7724_data).
Presumably this happened due to a patch conflict with commit
d407bc0203 ("sh-eth: Set fdr_value of R-Car SoCs"), which added
another field at the same position.
Move the field setting to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: b284fbe3b3 ("sh_eth: Fix access to TRSCER register")
Signed-off-by: David S. Miller <davem@davemloft.net>
TRSCER register is configured differently by SoCs. TRSCER of R-Car Gen2 is
RINT8 bit only valid, other bits are reserved bits. This removes access to
TRSCER register reserve bit by adding variable trscer_err_mask to
sh_eth_cpu_data structure, set the register information to each SoCs.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDR register of R-Car set in fdr_value can have the original settings.
This sets the value that is suitable for each SoCs to fdr_value of R8A777x
and R8A779x.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
PTR_ALIGN macro after skb_reserve is redundant, because skb_reserve
function adjusts the alignment of skb->data.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both of 'boguscnt' and 'quota' have nearly meaning as the condition of
the reception loop.
In order to cut down redundant processing, this patch changes excess
judgement.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, allocation size of skb does not care the alignment
adjust after allocation.
And also, in the current implementation, buffer alignment method by
sh_eth_set_receive_align function has a bug that this function displace
buffer start address forcedly when the alignment is corrected.
In the result, tail of the skb will exceed allocated area and kernel panic
will be occurred.
This patch fix this issue.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device tree probing for R-Car M2N (r8a7793) is added.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using RMMI mode, it is necessary to change in probe.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_ioremap_resource checks platform_get_resource() return value.
We can remove the duplicate check here.
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
Renesas SuperH Ethernet support should be available only on
Renesas ARM SoCs and SuperH architecture.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since consume_skb() (and hence dev_kfree_skb() macro) checks the passed pointer
for NULL, there's no need to check for NULL before invoking dev_kfree_skb().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that we cannot use nfs rootfs correctly
on r8a7790 when the command below runs on a host PC.
$ sudo ping -f -l 8 $BOARD_IP_ADDR
Since the driver sets the RACT to 1 in the first while loop of
sh_eth_rx(), the controller accepts a next frame into the next RX
descriptor during the while loop. But, in the first while loop
doesn't allocate a next skb. So, this patch removes the RACT setting
in the first while loop of sh_eth_rx().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the packet "exceeded" condition in sh_eth_rx() when
RACT in an RX descriptor is not set and the "quota" is 0.
Otherwise, kernel panic happens because the "&n->poll_list" is deleted
twice in sh_eth_poll() which calls napi_complete() and net_rx_action().
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4a55530f38 (net: sh_eth: modify the definitions of register) managed
to leave out the E-DMAC register entries in sh_eth_offset_fast_sh3_sh2[], thus
totally breaking SH7619/771x support. Add the missing entries using the data
from before that commit.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current behaviour of the sh_eth driver is not to use the RNC bit
for the receive ring. This means that every packet recieved is not only
generating an IRQ but it also stops the receive ring DMA as well until
the driver re-enables it after unloading the packet.
This means that a number of the following errors are generated due to
the receive packet FIFO overflowing due to nowhere to put packets:
net eth0: Receive FIFO Overflow
Since feedback from Yoshihiro Shimoda shows that every supported LSI
for this driver should have the bit enabled it seems the best way is
to remove the RMCR default value from the per-system data and just
write it when initialising the RMCR value. This is discussed in
the message (http://www.spinics.net/lists/netdev/msg284912.html).
I have tested the RMCR_RNC configuration with NFS root filesystem and
the driver has not failed yet. There are further test reports from
Sergei Shtylov and others for both the R8A7790 and R8A7791.
There is also feedback fron Cao Minh Hiep[1] which reports the
same issue in (http://comments.gmane.org/gmane.linux.network/316285)
showing this fixes issues with losing UDP datagrams under iperf.
Tested-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I was converting the driver to the managed device API, only devm_kzalloc()
was available for memory allocation, so I had to use it, despite zeroing out the
PHY IRQ array right before initializing all its entries to PHY_POLL was quite
stupid. Now that devm_kmalloc_array() has become available, we can avoid the
needless zeroing out...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pm_rumtime work queue is causing the device to be suspended during
initialisation, thus the initialisation may not be able to access registers
properly. As the code is called from a work queue, it is possible that this
is not seen from certain configurations/builds due to the asynchronos
nature of the code.
Another issue has also been found where the network device registration
calls back into the driver thus causing further pm_runtime calls that
also caused issues with the MDIO bus code. This has now been checked
and is the only place the MDIO can be called without the device open.
Use pm_runtime_get_sync() and pm_runtime_put() to ensure that the
pm system does not suspend it during the probe() call and remove the
now unnecessary pm_runtime_resume() call. Also add a call in the error
path to call pm_runtime_disable().
This fixes the external abort that can cause /sbin/init or other such
init processed to die.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"goto" is well accepted for error paths in the kernel but should not be
used unnecessarily. Return the correct value directly instead of using a
goto when possible.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network API functions that rely on the MDIO bus can be called as soon as
the driver calls register_netdev(). Register the MDIO bus before the
network device to avoid race conditions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device passed to the sh_mdio_init and sh_mdio_release
functions is only used to access the sh_eth_private instance. Pass it
directly to those functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO bus parent is set to the network device. Beside not reflecting
the hardware topology, this prevents registering the MDIO bus before
initializing the network device. Fix it by setting the MDIO bus parent
to the platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
