Introduce a dsa_user_ports() helper to return the ds->enabled_port_mask
mask which is more explicit. This will also minimize diffs when touching
this internal mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the DSA code still check ds->enabled_port_mask directly to
inspect a given port type instead of using the provided dsa_is_user_port
helper. Change this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames dsa_is_normal_port to dsa_is_user_port because "user"
is the correct term in the DSA terminology, not "normal".
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unused ports are currently configured in normal mode. This does not
prevent the switch from being functional, but it is unnecessary. Skip
unused ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the comment above the chunk states, the b53 driver attempts to
disable the unused ports. But using ds->enabled_port_mask is misleading,
because this mask reports in fact the user ports.
To avoid confusion and fix this, this patch introduces an explicit
dsa_is_unused_port helper which ensures the corresponding bit is not
masked in any of the switch port masks.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch require net/dsa/tag_lan9303.c to access struct lan9303.
Therefore move struct lan9303 definitions from drivers/net/dsa/lan9303.h
to new file include/linux/dsa/lan9303.h.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the LAN9303 work when lan9303_probe() is called twice.
For some unknown reason the LAN9303 switch fail to forward data when switch
fabric port 0 TX is disabled during probe. (Write of LAN9303_MAC_TX_CFG_0
in lan9303_disable_processing_port().)
In that situation the switch fabric seem to receive frames, because the ALR
is learning addresses. But no frames are transmitted on any of the ports.
In our system lan9303_probe() is called twice, first time
dsa_register_switch() return -EPROBE_DEFER. As an experiment, modified the
code to skip writing LAN9303_MAC_TX_CFG_0, port 0 during the first probe.
Then the switch works as expected.
Resolve the problem by not calling lan9303_disable_processing_port() on
port 0 during probe. Ports 1 and 2 are still disabled.
Although unsatisfying that the exact failure mechanism is not known,
the patch should not cause any harm.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason why we should limit ourselves to matching only
full IPv4 addresses (/32), the same logic applies between the DATA and
MASK ports, so just make it more configurable to accept both.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason why we should limit ourselves to matching only full
IPv4 addresses (/32), the same logic applies between the DATA and MASK
ports, so just make it more configurable to accept both.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inserting IPv6 CFP rules complicates the code a little bit in that we
need to insert two rules side by side and chain them to match a full
IPv6 tuple (src, dst IPv6 + port + protocol).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to do a HW search of the TCAMs which is something slow
and expensive. Since we already maintain a bitmask of active CFP rules,
just iterate over those, starting from bit 1 (after the reserved entry)
to get a count and index position to store the rule later on.
As a result we can remove the code in bcm_sf2_cfp_rule_get() which acted
on the "search" argument, and remove that argument.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for introducing IPv6 rules support, make the
cfp_udf_layout more flexible and match more accurately how the HW is
designed: we have 3 + 1 slices per protocol, but we may not be using all
of them and we are relative to a particular base offset (slice A for
IPv4 for instance). Also populate the slice number that should be used
(slice 1 for IPv4) based on the lookup function.
Finally, we introduce two helper functions: udf_upper_bits() and
udf_lower_bits() to help setting the UDF_n_* valid bits based on the
number of UDFs valid within a slice. Update the IPv4 rule setting to
make use of it to be more robust wrt. change in number of User Defined
Fields being programmed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the processing of IPv4 rules into specific functions, allowing us
to clearly identify which parts are generic and which ones are not. Also
create a specific function to insert a rule into the action and policer
RAMs as those tend to be fairly generic.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of open coding the shift for the IP protocol, IP fragment bit
etc. define and/or use existing constants to that end.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions for managing the lan9303 ALR (Address Logic
Resolution).
Implement DSA methods: port_fdb_add, port_fdb_del, port_mdb_prepare,
port_mdb_add and port_mdb_del.
Since the lan9303 do not offer reading specific ALR entry, the driver
caches all static entries - in a flat table.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DSA method port_fast_age as a step to STP support.
Add low level functions for accessing the lan9303 ALR (Address Logic
Resolution).
Added DSA method port_fdb_dump
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure is part of DSA core data and must only be updated
by the later. It is OK and sometimes necessary for the DSA drivers to
access this data, but this has to be read only.
For that purpose, add a dsa_to_port() helper which returns a const
pointer to a dsa_port structure which must be used by DSA drivers from
now on instead of digging into ds->ports[] themselves.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure has a "netdev" member, which can be used for
either the master device, or the slave device, depending on its type.
It is true that today, CPU port are not exposed to userspace, thus the
port's netdev member can be used to point to its master interface.
But it is still slightly confusing, so split it into more explicit
"master" and "slave" members inside an anonymous union.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .set_addr function does nothing, remove the dsa_loop implementation
before getting rid of it completely in DSA.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for mv88e6xxx, setup the switch from within the mv88e6060 driver with
a random MAC address, and remove the .set_addr implementation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6060 Ethernet switch always transmits the multicast bit of the
switch MAC address as a zero. It re-uses the corresponding bit 8 of the
register "Switch MAC Address Register Bytes 0 & 1" for "DiffAddr".
If the "DiffAddr" bit is 0, then all ports transmit the same source
address. If it is set to 1, then bit 2:0 are used for the port number.
The mv88e6060 driver is currently wrongly shifting the MAC address byte
0 by 9. To fix this, shift it by 8 as usual and clear its bit 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An Ethernet switch may support having a MAC address, which can be used
as the switch's source address in transmitted full-duplex Pause frames.
If a DSA switch supports the related .set_addr operation, the DSA core
sets the master's MAC address on the switch. This won't make sense
anymore in a multi-CPU ports system, because there won't be a unique
master device assigned to a switch tree.
Instead, setup the switch from within the Marvell driver with a random
MAC address, and remove the .set_addr implementation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turn on the out of band Advanced Congestion Buffering (ACB) mechanism at
the switch level now that we have properly established the queue mapping
between the switch egress queues and the SYSTEMPORT egress queues. This
allows the switch to correctly backpressure the host system when one of
its queue drops below the configured thresholds.
This is also helping achieve so called "lossless" behavior by adapting
the TX interrupt pacing to the actual speed and capacity of the switch
port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both user ports are joined to the same bridge, the normal
HW MAC learning is enabled. This means that unicast traffic is forwarded
in HW.
If one of the user ports leave the bridge,
the ports goes back to the initial separated operation.
Port separation relies on disabled HW MAC learning. Hence the condition
that both ports must join same bridge.
Add brigde methods port_bridge_join, port_bridge_leave and
port_stp_state_set.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for next patch:
Move tag setup from lan9303_separate_ports() to new function
lan9303_setup_tagging()
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mt7530_phy_write is local to the source and does not need to
be in global scope, so make it static.
Cleans up sparse warnings:
symbol 'mt7530_phy_write' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions lan9303_mdio_phy_write and lan9303_mdio_phy_read are local
to the source and do not need to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'lan9303_mdio_phy_write' was not declared. Should it be static?
symbol 'lan9303_mdio_phy_read' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e85ec74ace ("net: dsa: bcm_sf2: Defer port
enabling to calling port_enable") because this now makes an unbind
followed by a bind to fail connecting to the ingrated PHY.
What this patch missed is that we need the PHY to be enabled with
bcm_sf2_gphy_enable_set() before probing it on the MDIO bus. This is
correctly done in the ops->setup() function, but by the time
ops->port_enable() runs, this is too late. Upon unbind we would power
down the PHY, and so when we would bind again, the PHY would be left
powered off.
Fixes: e85ec74ace ("net: dsa: bcm_sf2: Defer port enabling to calling port_enable")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g2_irq_free locks the registers mutex, but not
mv88e6xxx_g1_irq_free, which results in a stack trace from
assert_reg_lock when unloading the mv88e6xxx module. Fix this.
Fixes: 3460a5770c ("net: dsa: mv88e6xxx: Mask g1 interrupts and free interrupt")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ports with the same VLAN must all be in the same bridge. However the
CPU and DSA ports need to be in multiple VLANs spread over multiple
bridges. So exclude them when performing this test.
Fixes: b2f81d304c ("net: dsa: add CPU and DSA ports as VLAN members")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each port in DSA has its own dedicated CPU port currently available in
its parent switch's ds->ports[port].cpu_dp. Use it instead of getting
the unique tree CPU port, which will be deprecated soon.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the driver react to device tree "fixed-link" declaration on CPU port.
- turn off autonegotiation
- force speed 10 or 100 mb/s
- force duplex mode
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export b53_{enable,disable}_port and use these two functions in
bcm_sf2_port_setup and bcm_sf2_port_disable. The generic functions
cannot be used without wrapping because we need to manage additional
switch integration details (PHY, Broadcom tag etc.).
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The magic number 8 in 3 locations in bcm_sf2_cfp.c actually designates
the number of switch port egress queues, so use that define instead of
open-coding it.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sf2 and b53 do exactly the same thing, so share that piece.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for enabling and disabling EEE, as well as re-negotiating it in
.adjust_link() and in .port_enable().
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bcm_sf2 EEE-related functions to the b53 driver because this is shared
code amongst Gigabit capable switch, only 5325 and 5365 are too old to support
that.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for migrating the EEE code from bcm_sf2 to b53, define the full
EEE register page and offsets within that page.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to enable Broadcom tags/headers is largely switch independent,
and in preparation for enabling it for multiple devices with b53, move
the code we have in bcm_sf2.c to b53_common.c
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of repeating the same pattern: acquire mutex, read/write,
release mutex, define a macro: b53_build_op() which takes the type
(read|write), I/O size, and value (scalar or pointer). This helps with
fixing bugs that could exist (e.g: missing barrier, lock etc.).
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to configure the enabled ports once in bcm_sf2_sw_setup() and
then a second time around when dsa_switch_ops::port_enable is called, just do
it when port_enable is called which is better in terms of power consumption and
correctness.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to configure the enabled ports once in b53_setup() and then a
second time around when dsa_switch_ops::port_enable is called, just do it when
port_enable is called which is better in terms of power consumption and
correctness.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for future changes allowing the configuring of multiple
CPU ports, make b53_enable_cpu_port() take a port argument.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not used anywhere, so remove it.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though TC2QOS mapping is for switch egress queues, we need to
configure it correclty in order for the Broadcom tag ingress (CPU ->
switch) queue selection to work correctly since there is a 1:1 mapping
between switch egress queues and ingress queues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports 8 egress queues per port, so indicate that such that
net/dsa/slave.c::dsa_slave_create can allocate the right number of TX queues.
While at it use SF2_NUM_EGRESS_QUEUE as a define for the number of queues we
support.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During error injection it was possible to crash in dsa_loop_exit() because of
an attempt to unregister an invalid PHY. We actually want to the driver probing
in dsa_loop_init() even though fixed_phy_register() may return an error to
exercise how DSA deals with such cases, but we should not be crashing during
driver removal.
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
