Commit fdb487f5c9
("ARM: 8015/1: Add cpu_is_pj4 to distinguish PJ4 because it
has some differences with V7")
introduced a cpuid check for Marvell PJ4 processors to fix a
regression caused by adding PJ4 based Marvell Dove into
multi_v7.
Unfortunately, this check is too narrow to catch PJ4 used on
Dove itself and breaks iWMMXt support.
This patch therefore relaxes the cpuid mask to match both PJ4
and PJ4B. Also, rework the given comment about PJ4/PJ4B
modifications to be a little bit more specific about the
differences.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
commit fdb487f5c9
("ARM: 8015/1: Add cpu_is_pj4 to distinguish PJ4 because it
has some differences with V7")
introduced a fix for checking PJ4 cpuid to not use PJ4 specific
coprocessor access on non-PJ4 platforms.
Unfortunately, this in turn broke Marvell Armada 370/XP, both
comprising Marvell PJ4B CPUs without iWMMXt extension. Instead
of only checking for cpuid, which may not be sufficient to
determine iWMMXt support, the presence of iWMMXt coprocessors
can be checked by enabling and reading the Coprocessor ID
register (wCID, register 0 of CP1).
Therefore this adds an explicit check for the presence and correct
wCID value, before enabling iWMMXt capabilities. As a bonus, also
print the iWMMXt version of a detected coprocessor.
This has been tested to properly detect iWMMXt presence/absence on:
- PJ4, CPUID 0x560f5815, wCID 0x56052001: Marvell Dove, iWMMXt v2
- PJ4B, CPUID 0x561f5811: Marvell Armada 370, no iWMMXt
- PJ4B, CPUID 0x562f5841, wCID 0x56052001: Marvell Armada 1500, iWMMXt v2
- PJ4B, CPUID 0x562f5842: Marvell Armada XP, no iWMMXt
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes PJ4 coprocessor init to only expose iWMMXt capabilities,
if the corresponding kernel support for iWMMXt is enabled.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
iwmmxt.S requires special treatment of coprocessor access registers
for PJ4 and XScale-based CPUs. It only checks for CPU_PJ4 and drops
down to XScale-based treatment on all other architectures.
As some PJ4B also come with iWMMXt and also need PJ4 treatment,
rework the corresponding preprocessor directives to explicitly
check for supported architectures and fail on unsupported ones.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we had to retry on the profiles seqlock (due to a concurrent write), we
would set bits on the input flags that corresponded both to the current
profile and to previous values of the profile.
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
If skinny metadata is enabled and our first tree search fails to find a
skinny extent item, we may repeat a tree search for a "fat" extent item
(if the previous item in the leaf is not the "fat" extent we're looking
for). However we were not setting the new key's objectid to the right
value, as we previously used the same key variable to peek at the previous
item in the leaf, which has a different objectid. So just set the right
objectid to avoid modifying/deleting a wrong item if we repeat the tree
search.
Signed-off-by: Filipe David Borba Manana <fdmanana@gmail.com>
Signed-off-by: Chris Mason <clm@fb.com>
Currently, with inode cache enabled, we will reuse its inode id immediately
after unlinking file, we may hit something like following:
|->iput inode
|->return inode id into inode cache
|->create dir,fsync
|->power off
An easy way to reproduce this problem is:
mkfs.btrfs -f /dev/sdb
mount /dev/sdb /mnt -o inode_cache,commit=100
dd if=/dev/zero of=/mnt/data bs=1M count=10 oflag=sync
inode_id=`ls -i /mnt/data | awk '{print $1}'`
rm -f /mnt/data
i=1
while [ 1 ]
do
mkdir /mnt/dir_$i
test1=`stat /mnt/dir_$i | grep Inode: | awk '{print $4}'`
if [ $test1 -eq $inode_id ]
then
dd if=/dev/zero of=/mnt/dir_$i/data bs=1M count=1 oflag=sync
echo b > /proc/sysrq-trigger
fi
sleep 1
i=$(($i+1))
done
mount /dev/sdb /mnt
umount /dev/sdb
btrfs check /dev/sdb
We fix this problem by adding unlinked inode's id into pinned tree,
and we can not reuse them until committing transaction.
Cc: stable@vger.kernel.org
Signed-off-by: Miao Xie <miaox@cn.fujitsu.com>
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
Fix possible memory leaks in the following error handling paths:
read_tree_block()
btrfs_recover_log_trees
btrfs_commit_super()
btrfs_find_orphan_roots()
btrfs_cleanup_fs_roots()
Signed-off-by: Wang Shilong <wangsl.fnst@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
There's a case which clone does not handle and used to BUG_ON instead,
(testcase xfstests/btrfs/035), now returns EINVAL. This error code is
confusing to the ioctl caller, as it normally signifies errorneous
arguments.
Change it to ENOPNOTSUPP which allows a fall back to copy instead of
clone. This does not affect the common reflink operation.
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Chris Mason <clm@fb.com>
Commit 3ac0d7b96a fixed the btrfs expanding
write problem but the hole punched is sometimes too large for some
iovec, which has unmapped data ranges.
This patch will change to hole range to a more accurate value using the
counts checked by the write check routines.
Reported-by: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Qu Wenruo <quwenruo@cn.fujitsu.com>
Signed-off-by: Chris Mason <clm@fb.com>
While porting a RS485 driver from 2.6.29 to 3.14, i noticed that the serial tty
driver could break it by using uart ports that it does not own :
1. uart_change_pm ist called during uart_open and calls the uart pm function
without checking for PORT_UNKNOWN.
The fix is to move uart_change_pm from uart_open to uart_port_startup.
2. The return code from the uart request_port call in uart_set_info is not
handled properly, leading to the situation that the serial driver also
thinks it owns the uart ports.
This can triggered by doing following actions :
setserial /dev/ttyS0 uart none # release the uart ports
modprobe lirc-serial # or any other device that uses the uart
setserial /dev/ttyS0 uart 16550 # gives no error and the uart tty driver
# can use the ports as well
Signed-off-by: Thomas Pfaff <tpfaff@pcs.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two functions to write out to the console (one used in normal
console mode and one in polling console mode) were slightly different.
One used a barrier() in its loop and the other a cpu_relax(). The
barrier() really doesn't do anything since we're using rd_regl() to
read the port anyway. Switch it to cpu_relax() to make things
consistent.
No known bugs / issues are fixed by this change--it just makes things
more consistent.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The s3c24xx_serial_console_putchar() is _only_ ever used by
s3c24xx_serial_console_write() and is called in a loop (indirectly
through uart_console_write()). There's no reason to call
s3c24xx_port_configured() for every iteration through the loop. Move
it outside the loop.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The two functions in the samsung serial driver used for writing
characters out to the port were inconsistent about whether they used
the passed in "port" or the global "cons_uart". There was no reason
to use the global and the use of the global in
s3c24xx_serial_put_poll_char() caused a crash in the case where you
used the serial port for kgdboc but not for console.
Fix it so we used the passed in variable.
Note that this doesn't fix all problems with the samsung serial
driver. Specifically:
* s3c24xx_serial_console_putchar() is still 99% identical to
s3c24xx_serial_put_poll_char() (the function signature is different,
but that's about it). A future patch will make them slightly less
identical and judging by other serial drivers we may need yet more
differences eventually.
* The samsung serial driver still doesn't allow you to have more than
one console port since it still uses the global cons_uart in
s3c24xx_serial_console_write().
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__dma_tx_complete is not protected against concurrent
call of serial8250_tx_dma. it can lead to circular tail
index corruption or parallel call of serial_tx_dma on the
same data portion.
This patch fixes this issue by holding the port lock.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On transmit-hold-register empty, serial8250_tx_chars
should be called only if we don't use DMA.
DMA has its own tx cycle.
Signed-off-by: Loic Poulain <loic.poulain@intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The race was introduced while development of linux-3.11 by
e8437d7ecb and
e9975fdec0.
Originally it was found and reproduced on linux-3.12.15 and
linux-3.12.15-rt25, by sending 500 byte blocks with 115kbaud to the
target uart in a loop with 100 milliseconds delay.
In short:
1. The consumer flush_to_ldisc is on to remove the head tty_buffer.
2. The producer adds a number of bytes, so that a new tty_buffer must
be allocated and added by __tty_buffer_request_room.
3. The consumer removes the head tty_buffer element, without handling
newly committed data.
Detailed example:
* Initial buffer:
* Head, Tail -> 0: used=250; commit=250; read=240; next=NULL
* Consumer: ''flush_to_ldisc''
* consumed 10 Byte
* buffer:
* Head, Tail -> 0: used=250; commit=250; read=250; next=NULL
{{{
count = head->commit - head->read; // count = 0
if (!count) { // enter
// INTERRUPTED BY PRODUCER ->
if (head->next == NULL)
break;
buf->head = head->next;
tty_buffer_free(port, head);
continue;
}
}}}
* Producer: tty_insert_flip_... 10 bytes + tty_flip_buffer_push
* buffer:
* Head, Tail -> 0: used=250; commit=250; read=250; next=NULL
* added 6 bytes: head-element filled to maximum.
* buffer:
* Head, Tail -> 0: used=256; commit=250; read=250; next=NULL
* added 4 bytes: __tty_buffer_request_room is called
* buffer:
* Head -> 0: used=256; commit=256; read=250; next=1
* Tail -> 1: used=4; commit=0; read=250 next=NULL
* push (tty_flip_buffer_push)
* buffer:
* Head -> 0: used=256; commit=256; read=250; next=1
* Tail -> 1: used=4; commit=4; read=250 next=NULL
* Consumer
{{{
count = head->commit - head->read;
if (!count) {
// INTERRUPTED BY PRODUCER <-
if (head->next == NULL) // -> no break
break;
buf->head = head->next;
tty_buffer_free(port, head);
// ERROR: tty_buffer head freed -> 6 bytes lost
continue;
}
}}}
This patch reintroduces a spin_lock to protect this case. Perhaps later
a lock-less solution could be found.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Cc: stable <stable@vger.kernel.org> # 3.11
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This series contains straight-forward fixes for different
Versatile Express infrastructure drivers:
- NULL pointer dereference on the error path in the clk driver
- out of boundary array access in the dcscb driver
- broken restart/power off implementation
- mis-interpreted voltage unit in the spc driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJTWTroAAoJEL9jRaJfXa5PHMkIAJB2S6zuqIxn7qRsfeD5YauR
nz7AHjDaakoVy6YTaMdHQI+dXSK6BPUNvMbrKzW3WWbT4ktJ/r3k/OeeBv/2T93L
8KW1Bbif7kPfdfITwCCWDs5waTDVXSBC6AGGoXomzQIt4MqghhzoLRc6uvhnuYAL
R7ZJsTWRa+47LVOJsghVffMyNlwCMj//prW7PBY6RIZXhpcbI+FGYv5Rm1XRITWn
uL2cSulBmWeqMVCR/gFx8/K5TqZ90q835dD1Ggh+BeB1Vaifu9/cI3D8w0hl/xy9
nRneKdTaTEpKjgwI3up4vMFbLbMI7brdMphZ9ZeGgK+YuWXFDbKvvdwjvDJ4Tx0=
=BS4Q
-----END PGP SIGNATURE-----
Merge tag 'vexpress/fixes-for-3.15' of git://git.linaro.org/people/pawel.moll/linux into fixes
ARM Versatile Express fixes for 3.15
This series contains straight-forward fixes for different
Versatile Express infrastructure drivers:
- NULL pointer dereference on the error path in the clk driver
- out of boundary array access in the dcscb driver
- broken restart/power off implementation
- mis-interpreted voltage unit in the spc driver
* tag 'vexpress/fixes-for-3.15' of git://git.linaro.org/people/pawel.moll/linux:
ARM: vexpress/TC2: Convert OPP voltage to uV before storing
power/reset: vexpress: Fix restart/power off operation
arm/mach-vexpress: array accessed out of bounds
clk: vexpress: NULL dereference on error path
Includes an update to 3.15-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This fixes a regression on Keystone 2 platforms caused by patch
57303488cd
"usb: dwc3: adapt dwc3 core to use Generic PHY Framework" which adds
optional support of generic phy in DWC3 core.
On Keystone 2 platforms the USB is not working now because
CONFIG_GENERIC_PHY isn't set and, as result, Generic PHY APIs stubs
return -ENOSYS always. The log shows:
dwc3 2690000.dwc3: failed to initialize core
dwc3: probe of 2690000.dwc3 failed with error -38
Hence, fix it by making NULL a valid phy reference in Generic PHY
APIs stubs in the same way as it was done by the patch
04c2facad8 "drivers: phy: Make NULL
a valid phy reference".
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The kernel oopses in phy_lookup() due to 'phy->init_data' being NULL if we
register PHYs from a device tree probing driver and then call phy_get() on a
device that has no representation in the device tree (e.g. a PCI device).
Checking the pointer before dereferening it and skipping an interation if
it's NULL prevents this kernel oops.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When OMAP_CONTROL_USB was renamed to OMAP_CONTROL_PHY (commit
14da699b), its dependencies were lost in the process. Nothing in the
commit message indicates that this removal was intentional, so I think
it was by accident and the dependencies should be restored.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Roger Quadros <rogerq@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The top-level phy-samsung-usb2 driver may be configured as a
loadable module, which currently causes link errors because
of the dependency on the exynos{5250,4x12,4210}_usb2_phy_config
symbol. Solving this could be achieved by exporting these
symbols, but as the SoC-specific parts of the driver are not
currently built as modules, it seems better to just link
everything into one module and avoid the need for the export.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix driver new_id sysfs-attribute removal deadlock by making sure to
not hold any locks that the attribute operations grab when removing the
attribute.
Specifically, usb_serial_deregister holds the table mutex when
deregistering the driver, which includes removing the new_id attribute.
This can lead to a deadlock as writing to new_id increments the
attribute's active count before trying to grab the same mutex in
usb_serial_probe.
The deadlock can easily be triggered by inserting a sleep in
usb_serial_deregister and writing the id of an unbound device to new_id
during module unload.
As the table mutex (in this case) is used to prevent subdriver unload
during probe, it should be sufficient to only hold the lock while
manipulating the usb-serial driver list during deregister. A racing
probe will then either fail to find a matching subdriver or fail to get
the corresponding module reference.
Since v3.15-rc1 this also triggers the following lockdep warning:
======================================================
[ INFO: possible circular locking dependency detected ]
3.15.0-rc2 #123 Tainted: G W
-------------------------------------------------------
modprobe/190 is trying to acquire lock:
(s_active#4){++++.+}, at: [<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
but task is already holding lock:
(table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (table_lock){+.+.+.}:
[<c0075f84>] __lock_acquire+0x1694/0x1ce4
[<c0076de8>] lock_acquire+0xb4/0x154
[<c03af3cc>] _raw_spin_lock+0x4c/0x5c
[<c02bbc24>] usb_store_new_id+0x14c/0x1ac
[<bf007eb4>] new_id_store+0x68/0x70 [usbserial]
[<c025f568>] drv_attr_store+0x30/0x3c
[<c01690e0>] sysfs_kf_write+0x5c/0x60
[<c01682c0>] kernfs_fop_write+0xd4/0x194
[<c010881c>] vfs_write+0xbc/0x198
[<c0108e4c>] SyS_write+0x4c/0xa0
[<c000f880>] ret_fast_syscall+0x0/0x48
-> #0 (s_active#4){++++.+}:
[<c03a7a28>] print_circular_bug+0x68/0x2f8
[<c0076218>] __lock_acquire+0x1928/0x1ce4
[<c0076de8>] lock_acquire+0xb4/0x154
[<c0166b70>] __kernfs_remove+0x254/0x310
[<c0167aa0>] kernfs_remove_by_name_ns+0x4c/0x94
[<c0169fb8>] remove_files.isra.1+0x48/0x84
[<c016a2fc>] sysfs_remove_group+0x58/0xac
[<c016a414>] sysfs_remove_groups+0x34/0x44
[<c02623b8>] driver_remove_groups+0x1c/0x20
[<c0260e9c>] bus_remove_driver+0x3c/0xe4
[<c026235c>] driver_unregister+0x38/0x58
[<bf007fb4>] usb_serial_bus_deregister+0x84/0x88 [usbserial]
[<bf004db4>] usb_serial_deregister+0x6c/0x78 [usbserial]
[<bf005330>] usb_serial_deregister_drivers+0x2c/0x4c [usbserial]
[<bf016618>] usb_serial_module_exit+0x14/0x1c [sierra]
[<c009d6cc>] SyS_delete_module+0x184/0x210
[<c000f880>] ret_fast_syscall+0x0/0x48
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(table_lock);
lock(s_active#4);
lock(table_lock);
lock(s_active#4);
*** DEADLOCK ***
1 lock held by modprobe/190:
#0: (table_lock){+.+.+.}, at: [<bf004d84>] usb_serial_deregister+0x3c/0x78 [usbserial]
stack backtrace:
CPU: 0 PID: 190 Comm: modprobe Tainted: G W 3.15.0-rc2 #123
[<c0015e10>] (unwind_backtrace) from [<c0013728>] (show_stack+0x20/0x24)
[<c0013728>] (show_stack) from [<c03a9a54>] (dump_stack+0x24/0x28)
[<c03a9a54>] (dump_stack) from [<c03a7cac>] (print_circular_bug+0x2ec/0x2f8)
[<c03a7cac>] (print_circular_bug) from [<c0076218>] (__lock_acquire+0x1928/0x1ce4)
[<c0076218>] (__lock_acquire) from [<c0076de8>] (lock_acquire+0xb4/0x154)
[<c0076de8>] (lock_acquire) from [<c0166b70>] (__kernfs_remove+0x254/0x310)
[<c0166b70>] (__kernfs_remove) from [<c0167aa0>] (kernfs_remove_by_name_ns+0x4c/0x94)
[<c0167aa0>] (kernfs_remove_by_name_ns) from [<c0169fb8>] (remove_files.isra.1+0x48/0x84)
[<c0169fb8>] (remove_files.isra.1) from [<c016a2fc>] (sysfs_remove_group+0x58/0xac)
[<c016a2fc>] (sysfs_remove_group) from [<c016a414>] (sysfs_remove_groups+0x34/0x44)
[<c016a414>] (sysfs_remove_groups) from [<c02623b8>] (driver_remove_groups+0x1c/0x20)
[<c02623b8>] (driver_remove_groups) from [<c0260e9c>] (bus_remove_driver+0x3c/0xe4)
[<c0260e9c>] (bus_remove_driver) from [<c026235c>] (driver_unregister+0x38/0x58)
[<c026235c>] (driver_unregister) from [<bf007fb4>] (usb_serial_bus_deregister+0x84/0x88 [usbserial])
[<bf007fb4>] (usb_serial_bus_deregister [usbserial]) from [<bf004db4>] (usb_serial_deregister+0x6c/0x78 [usbserial])
[<bf004db4>] (usb_serial_deregister [usbserial]) from [<bf005330>] (usb_serial_deregister_drivers+0x2c/0x4c [usbserial])
[<bf005330>] (usb_serial_deregister_drivers [usbserial]) from [<bf016618>] (usb_serial_module_exit+0x14/0x1c [sierra])
[<bf016618>] (usb_serial_module_exit [sierra]) from [<c009d6cc>] (SyS_delete_module+0x184/0x210)
[<c009d6cc>] (SyS_delete_module) from [<c000f880>] (ret_fast_syscall+0x0/0x48)
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If no valid CHID value has previously been set on an HWA, writing a
value of all zeros will cause a kernel panic in uwb_radio_stop because
wusbhc->uwb_rc has not been set. This patch skips the call to
uwb_radio_stop if wusbhc->uwb_rc has not been initialized.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nesting a spin_lock_irq/unlock_irq inside a lock that has already
disabled interrupts will enable interrupts before we are ready when
spin_unlock_irq is called. This patch converts the inner lock to use
spin_lock and spin_unlock instead.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch converts the use of spin_lock_irq/spin_unlock_irq to
spin_lock_irqsave/spin_unlock_irqrestore in uwb_rc_set_drp_cmd_done
which is called from a USB completion handler. There are also
whitespace cleanups to make checkpatch.pl happy.
Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For internal PHY (like UTMI), the phy clock may from internal pll,
it is on/off on the fly, the access PORTSC.PTS will hang without
phy clock. So, the usb_phy_init which will open phy clock needs to
be called before hw_phymode_configure.
See: http://marc.info/?l=linux-arm-kernel&m=139350618732108&w=2
For external PHY (like ulpi), it needs to configure portsc.pts before
visit viewport, or the viewport can't be visited. so phy_phymode_configure
needs to be called before usb_phy_init.
See: cd0b42c2a6
It may not the best solution, but it can work for all situations.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Cc: shc_work@mail.ru
Cc: denis@eukrea.com
Cc: festevam@gmail.com
Cc: stable <stable@vger.kernel.org> # 3.14
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Quite a few fixes this time since I lost v3.15-rc2
window.
Most fixes are MUSB which learned to remove its debugfs directories
properly, got a fix for PHY handling and now knows that it should
make sure its clocks aren't gated before trying to access registers.
ffs got a race fix between ffs_epfile_io() and ffs_func_eps_disable().
dwc3 got a fix for system suspend/resume and now only iterates over
valid endpoints when trying to resize TX fifos.
usb_get_phy() now will properly return an error if try_module_get() fails.
We also have a revert for a NAPI conversion on the ethernet gadget which
was causing a kernel BUG.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aYvY
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.15-rc3
Quite a few fixes this time since I lost v3.15-rc2
window.
Most fixes are MUSB which learned to remove its debugfs directories
properly, got a fix for PHY handling and now knows that it should
make sure its clocks aren't gated before trying to access registers.
ffs got a race fix between ffs_epfile_io() and ffs_func_eps_disable().
dwc3 got a fix for system suspend/resume and now only iterates over
valid endpoints when trying to resize TX fifos.
usb_get_phy() now will properly return an error if try_module_get() fails.
We also have a revert for a NAPI conversion on the ethernet gadget which
was causing a kernel BUG.
Signed-of-by: Felipe Balbi <balbi@ti.com>
A couple of things here:
- Fixes for pbias that didn't make it in during the merge window due to
the driver coming in via MMC. The conversion to use helpers is a
fix as it implements list_voltage() which the main user (MMC) relies
on for correct functioning.
- Change the !REGULATOR stub for optional regulators to return an
error rather than a dummy; this is more in keeping with the intended
use of optional regulators and fixes some issues seen MMC where it
got confused by a dummy being provided.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=t/Ad
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A couple of things here:
- Fixes for pbias that didn't make it in during the merge window due
to the driver coming in via MMC. The conversion to use helpers is
a fix as it implements list_voltage() which the main user (MMC)
relies on for correct functioning.
- Change the !REGULATOR stub for optional regulators to return an
error rather than a dummy; this is more in keeping with the
intended use of optional regulators and fixes some issues seen MMC
where it got confused by a dummy being provided"
* tag 'regulator-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: core: Return error in get optional stub
regulator: pbias: Convert to use regmap helper functions
regulator: pbias: Fix is_enabled callback implementation
A few driver specific fixes here:
- SH HSPI was dealing with its clocks incorrectly which meant it didn't
work on some SoCs, fixing this also requires a small fix to one of
the SoC clock trees to avoid breaking existing users.
- The SiRF driver appears to have had several quality problems, it's
fairly new and not widely used so this isn't too worrying.
- A brute force fix for excessive locking in the Atmel driver, it needs
further investigation but this deals with the immediate issue.
- A build fix for the Blackfin driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=kM6u
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes here:
- SH HSPI was dealing with its clocks incorrectly which meant it
didn't work on some SoCs, fixing this also requires a small fix to
one of the SoC clock trees to avoid breaking existing users.
- The SiRF driver appears to have had several quality problems, it's
fairly new and not widely used so this isn't too worrying.
- A brute force fix for excessive locking in the Atmel driver, it
needs further investigation but this deals with the immediate
issue.
- A build fix for the Blackfin driver"
* tag 'spi-v3.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: atmel: Fix scheduling while atomic bug
spi: sh-hspi: Do not specifically request shyway_clk clock
ARM: shmobile: r8a7778: Use clks as MSTP007 parent
spi: sirf: make GPIO chipselect function work well
spi: sirf: set SPI controller in RISC IO chipselect mode
spi: sirf: correct TXFIFO empty interrupt status bit
spi: bfin5xx: fix build error
Commit 1a699476e2 "ACPI / hotplug / PCI: Hotplug notifications from
acpi_bus_notify()" changed the root notify handler, acpi_bus_notify(),
to block unknown type norifications, but it overlooked the fact that
they might be propagated to drivers via the ->notify() callback.
Fix the problem by allowing drivers to receive unknown type
notifications via ->notify() as before.
Fixes: 1a699476e2 (ACPI / hotplug / PCI: Hotplug notifications from acpi_bus_notify())
Reported-and-tested-by: Mantas Mikulėnas <grawity@gmail.com>
Reported-and-tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull dma-mapping fix from Marek Szyprowski:
"A small fix for dma-mapping subsystem for ARM"
* 'fixes_for_v3.15' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
arm: dma-mapping: Fix mapping size value
Pull libata fixes from Tejun Heo:
"Dan updated tag allocation to accomodate devices which choke when tags
jump back and forth. Quite a few ahci MSI related fixes. A couple
config dependency fixes and other misc fixes"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata/ahci: accommodate tag ordered controllers
ahci: Do not receive interrupts sent by dummy ports
ahci: Use pci_enable_msi_exact() instead of pci_enable_msi_range()
ahci: Ensure "MSI Revert to Single Message" mode is not enforced
ahci: do not request irq for dummy port
pata_samsung_cf: fix ata_host_activate() failure handling
pata_arasan_cf: fix ata_host_activate() failure handling
ata: fix i.MX AHCI driver dependencies
pata_at91: fix ata_host_activate() failure handling
libata: Update queued trim blacklist for M5x0 drives
libata: make AHCI_XGENE depend on PHY_XGENE
The SPC stores voltage in mV while the code assumes it was returning
uV. Convert the returned voltage to uV before storing. Also fix the
comment depicting voltage to uV.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
The restart/power off implementation in the vexpress driver
used to obtain the config function when necessary. This was
wrong in two respects:
1. It required memory allocation with disabled interrupts
(it worked, but lockdep - when enabled - reported warnings).
2. Used jiffies-based timeout, while jiffies are not running
at this stage of system shutdown (therefore a config
transaction error - if happened - would have never be reported).
Fixed by pre-allocating the config function per device
and using mdelay for timeout.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
The Tegra124 clock DT binding currently provides 3 clocks that don't
actually exist; 2 for NAND and one for UART5/UARTE. Delete these. While
this is technically an incompatible DT ABI change, nothing could have
used these clock IDs for anything practical, since the HW doesn't exist.
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Tegra124 clock driver currently provides 3 clocks that don't actually
exist; 2 for NAND and one for UART5/UARTE. Delete these.
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tegra124 only has 4 UARTs. Parts of the documentation hint at a fifth
UART, but this appears to be left-over from earlier SoC documentation.
Remove the non-existent DT node for UART5.
Cc: <stable@vger.kernel.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
device tree based booting. And turns out BeagleBoard xM A/B
needs it's own minimal dts in addition to the related u-boot
changes. Also few minor documentation and typo fixes are merged
to get them out of the way.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=co/l
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps, mostly to fix some GPMC, DSS and USB issues for
device tree based booting. And turns out BeagleBoard xM A/B
needs it's own minimal dts in addition to the related u-boot
changes. Also few minor documentation and typo fixes are merged
to get them out of the way.
* tag 'omap-for-v3.15/fixes-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix GPMC remap for devices using an offset
ARM: OMAP2+: Fix oops for GPMC free
ARM: dts: Add support for the BeagleBoard xM A/B
ARM: dts: Grammar /that will/it will/
ARM: dts: Grammar /is uses/ is used/
ARM: OMAP2+: Fix config name for USB3 PHY
ARM: dts: am335x: update USB DT references
ARM: dts: OMAP2+: remove uses of obsolete gpmc,device-nand
ARM: AM335X: EVM: fix pinmux documentation in devicetree
ARM: OMAP2+: N900: remove omapdss init for DT boot
ARM: dts: dra7xx-clocks: Correct mcasp2_ahclkx_mux bit-shift
ARM: dts: omap5: Add clocks to USB3 PHY node
ARM: OMAP2+: hwmod: fix missing braces in _init()
ARM: AM43xx: fix dpll init in bypass mode
ARM: OMAP3: hwmod data: Correct clock domains for USB modules
ARM: OMAP3: PM: remove access to PRM_VOLTCTRL register
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Updates the Ux500 (U8500) defconfig
- Selects PARTITION_ADVANCED for Ux500 and U300
- Configure in IIO sensor drivers for the Ux500
- Configure in the CW1200 WLAN chip for the Ux500
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Xe+n
-----END PGP SIGNATURE-----
Merge tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into fixes
This is a patch set for some ST-Ericsson devices:
- Updates the Ux500 (U8500) defconfig
- Selects PARTITION_ADVANCED for Ux500 and U300
- Configure in IIO sensor drivers for the Ux500
- Configure in the CW1200 WLAN chip for the Ux500
* tag 'ux500-defconfig-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: configure for CW1200 WLAN chip
ARM: ux500: configure in sensors
ARM: u300: u300_defconfig: Enable PARTITION_ADVANCED
ARM: ux500: u8500_defconfig: Enable PARTITION_ADVANCED
ARM: ux500: update defconfig
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Correct renesas,groups in SDHI nodes of for r8a7790 (R-Car H2) based
Lager board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=ANme
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Fifth Round of Renesas ARM Based SoC DT Updates for v3.15
Correct renesas,groups in SDHI nodes of for r8a7790 (R-Car H2) based
Lager board.
* tag 'renesas-dt5-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager: correct renesas,gpios to renesas,groups in sd[02] pfc
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A couple of dts changes for the fallout of imx-drm binding update
- Parent DI clocks to video PLL for better HDMI support
- PCIe interrupt mapping and GIC node fixes
- A series of edmqmx6 board fixes
- Other small and random fixes on imx5 and imx6 dts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJTTOc9AAoJEFBXWFqHsHzO+S0H+wbYC7IJxwJ8YVRHChFAs6gV
vUP3MICQV49PUReGxhsc0iJmjnc8fJtXDR4wH7rmzlxQYdrYsnFYBk+yPXO6GhqW
Js4hkS4V/9CbGmL7v53eGhW9TyTq0yE+vWpKXZTyDoCbKKkfhKrtfRIjZgkdNBZD
3XAZ4zm3LFwca/GwLN2RSjJ6mdPX24pm+SDnblHqDvz/3KyfBQj2AYUYjRxElide
YcsUMcXU+/aJD1JTVdriw9lsP7sqJzsemj948j8XakBoU32A+DuoBuB0Dhm9Uv10
2qydt1R5pR9q2iX1/FYzZyTjs+KOW3ds8/Z36+MbWTytYS9TwzQ6bln0nOCUNhw=
=eymy
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
The i.MX fixes for 3.15:
- A couple of dts changes for the fallout of imx-drm binding update
- Parent DI clocks to video PLL for better HDMI support
- PCIe interrupt mapping and GIC node fixes
- A series of edmqmx6 board fixes
- Other small and random fixes on imx5 and imx6 dts
* tag 'imx-fixes-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: i.MX6: ipu_di_sel clocks can set parent rates
ARM: imx6q: clk: Parent DI clocks to video PLL via di_pre_sel
ARM: dts: imx: add required #clock-cells for fixed-clock
ARM: dts: vybrid: drop address and size cells from GIC node
ARM: dts: imx6sl-evk: Add an entry for MX6SL_PAD_ECSPI1_SS0__GPIO4_IO11
ARM: dts: imx53: fix apparent copy/paste error
ARM: dts: imx6q-gw5xxx: remove dead 'crtcs' property
ARM: dts: imx53-tx53: add IPU DI ports and endpoints
ARM: dts: imx6: edmqmx6: add second STMPE
ARM: dts: imx6: edmqmx6: USB H1 only supports host mode
ARM: dts: imx6: edmqmx6: Do not use the OTG switch as VBUS regulator
ARM: dts: imx6: edmqmx6: Fix usbotg id pin
ARM: dt: microsom: don't set bit 7 for ethernet mux settings
ARM: imx6q-clk: parent lvds_gate from lvds_sel
ARM: dts: imx: drop invalid size and address cells properties
ARM: dts: mx5: fix wrong stmpe-ts bindings
ARM: dts: imx53-m53evk: Fix memory region description
ARM: dts: imx53-qsb-common: Fix memory region description
ARM: dts: imx6: add PCIe interrupt mapping properties
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit a7cbe92cef ("ARM: tegra: remove tegra EMC scaling driver")
removed the only user of TEGRA_EMC_SCALING_ENABLE. Remove its Kconfig
entry too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Few things were out of order:
- removed ARCH_BCM2835 duplicate
- shuffled ARCH_BCM_5301X, ARCH_U8500 and ARCH_U300 around so to keep the
list sorted
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
