After discussing with the subarch maintainers and Hilscher,
we concluded that the netx subarchitecture (Netx 100/500)
is no longer maintained or tested, and noone will miss it
if we delete it. So delete it.
There is a newer Netx 4000 architecture which we may see
included at some point, but this will be supported using
the standard multiplatform and devicetree mechanisms and is
easier to develop from scratch.
Cc: Michael Trensch <MTrensch@hilscher.com>
Acked-By: Robert Schwebel <r.schwebel@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to multiplatform enabled.
- Cleanups of Davinci
This tag also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlzc+sMPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3ygQP/3mxLFGJxgHk6m/41V4Tepv9F2ZZ3BW4Lcp7
vZtr6xiyhZXzIHOGzqQ4VGllfWhMWnjzZZe3iruSBY1gpJU7D4x054T3xVsIDs9F
EIcbBm5fE0O0bdijfk7V8vBu7LOIP/KYdaD1n9WDhW0Hy4wTXN8NNLSKEU5Lq15p
oz/A3QP5GcwhGAqaHyxx445La9yEKKWAsc2cOCRCdvfw6+n1GpoE6TI1YGjDvqbw
xd73mIwXb0l0f7jhCV7OPyZ3t/aQgTD3ddr4gHUGNa8sSWmD5nupSVxj23FkbGby
ejqJMxOfHpJJGIL/sxmR3+cFBYxyE+JNmrEq/kDW5ncWs/LY91juJxR1dkQKs6Mj
4Y9CWruftDz34DlFs/J33hF/rdZ73O91ldk7zqND41Fi5aLrIKvZBJlTuqyZ0tGV
YNRxsjWF953h8TXimDV0KvBgO4+E8d5ype/kIYtEGYO9DVmXQGMxFx2Gt2I/NfoH
5tCtVFwDPpMxJShpXHLMzUT8sQL3mytg5L/MIPTGx+zAtDwx/qTLEEAElffG29oI
vdzgJR0lrG/zzqQh25/M80UZYMdOrwtjAB42C+jAvlfQ0C4DtvSH+8OdcROOgj0b
GbAJbTdHYTD6OpoxhSuRii7zzNxw+i7pQj+uLSt8s8ZReGkUk5a2wpRpoVoV2WxK
RJHkMK95
=pUeO
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC updates, mostly refactorings and cleanups of old legacy platforms.
Major themes this release:
- Conversion of ixp4xx to a modern platform (drivers, DT, bindings)
- Moving some of the ep93xx headers around to get it closer to
multiplatform enabled.
- Cleanups of Davinci
This also contains a few patches that were queued up as fixes before
5.1 but I didn't get sent in before release"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
ARM: debug-ll: add default address for digicolor
ARM: u300: regulator: add MODULE_LICENSE()
ARM: ep93xx: move private headers out of mach/*
ARM: ep93xx: move pinctrl interfaces into include/linux/soc
ARM: ep93xx: keypad: stop using mach/platform.h
ARM: ep93xx: move network platform data to separate header
ARM: stm32: add AMBA support for stm32 family
MAINTAINERS: update arch/arm/mach-davinci
ARM: rockchip: add missing of_node_put in rockchip_smp_prepare_pmu
ARM: dts: Add queue manager and NPE to the IXP4xx DTSI
soc: ixp4xx: qmgr: Add DT probe code
soc: ixp4xx: qmgr: Add DT bindings for IXP4xx qmgr
soc: ixp4xx: npe: Add DT probe code
soc: ixp4xx: Add DT bindings for IXP4xx NPE
soc: ixp4xx: qmgr: Pass resources
soc: ixp4xx: Remove unused functions
soc: ixp4xx: Uninline several functions
soc: ixp4xx: npe: Pass addresses as resources
ARM: ixp4xx: Turn the QMGR into a platform device
ARM: ixp4xx: Turn the NPE into a platform device
...
The digicolor platform has three UARTs, but the Kconfig.debug
file explicitly lists port zero as the one to be used for the
console, while not providing any default values.
This can get an automated randconfig build stuck in a loop
waiting for the user to input the number. As we already know
the physical address, this patch provides that number as
default, along with a reasonable default value for the virtual
address.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Olof Johansson <olof@lixom.net>
Naresh Kamboju recently reported that the function-graph tracer crashes
on ARM. The function-graph tracer assumes that the kernel is built with
frame pointers.
We explicitly disabled the function-graph tracer when building Thumb2,
since the Thumb2 ABI doesn't have frame pointers.
We recently changed the way the unwinder method was selected, which
seems to have made it more likely that we can end up with the function-
graph tracer enabled but without the kernel built with frame pointers.
Fix up the function graph tracer dependencies so the option is not
available when we have no possibility of having frame pointers, and
adjust the dependencies on the unwinder option to hide the non-frame
pointer unwinder options if the function-graph tracer is enabled.
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
- An improvement on i.MX debugging options that only defines
DEBUG_IMX_UART_PORT if needed, so that the option will not be present
in the kernel config when DEBUG_LL is disabled.
- Adds the necessary platform support for i.MX7ULP SoC and configures
power mode to Partial Stop mode 3 with system/bus clock enabled.
Otherwise the default STOP mode will gate off system/bus clock when
WFI gets executed on i.MX7ULP.
- A fix from Arnd on SOC_IMX7ULP option dependency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDyTRAAoJEFBXWFqHsHzO87EH/jpMN5pDQG1z/lskwx7I8LJe
S6s1jP06NKpyupb9SfmA+HpuJOv4+77QkSBNpM3F3qDCjwx/10A0P0vnzP+csboz
oIj7/oIPGvKni6jsmJuNAGTkLQ+Vg+2f1ac/Cp0HF/lJg4r2TM+IX52wZmGmDyC6
4tPGM1IzZ5qj5nddzd1ox9df8Qq31wBSxEmy4YPwMtc3CfFRvy26BHdOqEl9swUs
wyOdjzhCYuaJ/sPUdr6oO/VWnXVvEV5Wmk5jmDOcPDeUCAJpH8Uz6oFoO/pW/qFn
1BloikV2Y4/NzU6Prfdl85bk8aHM2p6lqGiS5u9oHVFjQaoBq7MYD/nZDCFJeZY=
=POyl
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
i.MX SoC changes for 4.21:
- An improvement on i.MX debugging options that only defines
DEBUG_IMX_UART_PORT if needed, so that the option will not be present
in the kernel config when DEBUG_LL is disabled.
- Adds the necessary platform support for i.MX7ULP SoC and configures
power mode to Partial Stop mode 3 with system/bus clock enabled.
Otherwise the default STOP mode will gate off system/bus clock when
WFI gets executed on i.MX7ULP.
- A fix from Arnd on SOC_IMX7ULP option dependency.
* tag 'imx-soc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: fix dependencies on imx7ulp
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
Signed-off-by: Olof Johansson <olof@lixom.net>
If debugging on i.MX is enabled DEBUG_IMX_UART_PORT defines which UART
is used for the debug output. If however debugging is off don't only
hide the then unused config item but drop it completely by using a
dependency instead of a conditional prompt.
This fixes DEBUG_IMX_UART_PORT being present in the kernel config even
if DEBUG_LL is disabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Split Kconfig options for debug UART on Cyclone5
- Remove unused functions from socfpga platform code
- Turn on ARM and PL310 errata for SOCFPGA ARMv7 platform
-----BEGIN PGP SIGNATURE-----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=0ypv
-----END PGP SIGNATURE-----
Merge tag 'socfpga_updates_for_v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/soc
SoCFPGA updates for v5.0
- Split Kconfig options for debug UART on Cyclone5
- Remove unused functions from socfpga platform code
- Turn on ARM and PL310 errata for SOCFPGA ARMv7 platform
* tag 'socfpga_updates_for_v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: Turn on ARM errata for L2 cache
ARM: socfpga: Clean unused functions
ARM: debug: enable UART1 for socfpga Cyclone5
Signed-off-by: Olof Johansson <olof@lixom.net>
Cyclone5 and Arria10 doesn't have the same memory map for UART1.
Split the SOCFPGA_UART1 into 2 options to allow debugging on UART1 for Cyclone5.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
This adds low-level debug support on USART1 for STM32F4
and STM32F7.
Compiled via 'CONFIG_DEBUG_LL' and 'CONFIG_EARLY_PRINTK'.
Enabled via 'earlyprintk' in bootargs.
Signed-off-by: Gerald Baeza <gerald.baeza@st.com>
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
A couple of platforms change hands in the MAINTAINERS file:
- Linus Walleij lists himself for the ARM Reference platforms:
versatile, vexpress, integrator and realview. He has been the main
contributor for these for a while, and makes it official now.
- Vladimir Zapolskiy takes over the LPC18xx platform from Joachim Eastwood
- Manivannan Sadhasivam becomes a secondary maintainer for the
Actions Semi machines
- Nicolas Ferre lists updates the MAINTAINER listing for the AT91
platform: Ludovic Desroches is now a co-maintainer for the platform, and
several other people (Claudiu Beznea, Cristian Birsan, Eugen Hristev,
Codrin Ciubotariu) take over individual device drivers.
Thanks everyone for working on this, and welcome to the new maintainers!
The "virt" platform on qemy or kvm can now be used in big-endian mode
without additional tricks, thanks to Jason Donenfeld.
Once again, we gain support for another NXP i.MX6 variant, this time
it's the i.MX 6ULZ 32-bit single-core version.
On arm64, we add support for two SoCs from Renesas: RZ/G2E (r8a774c0)
and RZ/G2M (r8a774a1). These are described as microcontrollers on the
manufacturer website, but appear to be rather powerful. The RZ/G2M is
used on the reference board for the CIP Super Long Term Support (SLTS)
Linux Kernels.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7+46
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"A couple of platforms change hands in the MAINTAINERS file:
- Linus Walleij lists himself for the ARM Reference platforms:
versatile, vexpress, integrator and realview. He has been the main
contributor for these for a while, and makes it official now.
- Vladimir Zapolskiy takes over the LPC18xx platform from Joachim
Eastwood
- Manivannan Sadhasivam becomes a secondary maintainer for the
Actions Semi machines
- Nicolas Ferre lists updates the MAINTAINER listing for the AT91
platform: Ludovic Desroches is now a co-maintainer for the
platform, and several other people (Claudiu Beznea, Cristian
Birsan, Eugen Hristev, Codrin Ciubotariu) take over individual
device drivers.
Thanks everyone for working on this, and welcome to the new
maintainers!
The "virt" platform on qemy or kvm can now be used in big-endian mode
without additional tricks, thanks to Jason Donenfeld.
Once again, we gain support for another NXP i.MX6 variant, this time
it's the i.MX 6ULZ 32-bit single-core version.
On arm64, we add support for two SoCs from Renesas: RZ/G2E (r8a774c0)
and RZ/G2M (r8a774a1). These are described as microcontrollers on the
manufacturer website, but appear to be rather powerful. The RZ/G2M is
used on the reference board for the CIP Super Long Term Support (SLTS)
Linux Kernels"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
MAINTAINERS: Assign myself as a maintainer of ARM/LPC18XX architecture
arm64: exynos: Enable generic power domain support
MAINTAINERS: remove non-exsiting email address of Baoyou
MAINTAINERS: fix pattern in ARM/Synaptics berlin SoC section
MAINTAINERS: Drop dt-bindings/genpd/k2g.h
ARM: samsung: Limit SAMSUNG_PM_CHECK config option to non-Exynos platforms
arm64: actions: Enable PINCTRL in platforms Kconfig
MAINTAINERS: Add entry for Actions Semi Owl SoCs DMA driver
MAINTAINERS: Add entry for Actions Semiconductor Owl I2C driver
MAINTAINERS: Update clock binding entry for Actions Semi Owl SoCs
ARM: imx: add i.mx6ulz msl support
ARM: Assume maintainership of ARM reference designs
ARM: support big-endian for the virt architecture
MAINTAINERS: sdhci: move the Microchip entry to proper location
MAINTAINERS: move former ATMEL entries to proper MICROCHIP location
MAINTAINERS: remove the / ATMEL string from MICROCHIP entries
MAINTAINERS: iio: add co-maintainer to SAMA5D2-compatible ADC driver
MAINTAINERS: pwm: add entry for Microchip pwm driver
MAINTAINERS: dmaengine: add files to Microchip dma entry
MAINTAINERS: USB: change maintainer for Microchip USBA gadget driver
...
While in theory multiple unwinders could be compiled in, it does
not make sense in practise. Use a choice to make the unwinder
selection mutually exclusive and mandatory.
Already before this commit it has not been possible to deselect
FRAME_POINTER. Remove the obsolete comment.
Furthermore, to produce a meaningful backtrace with FRAME_POINTER
enabled the kernel needs a specific function prologue:
mov ip, sp
stmfd sp!, {fp, ip, lr, pc}
sub fp, ip, #4
To get to the required prologue gcc uses apcs and no-sched-prolog.
This compiler options are not available on clang, and clang is not
able to generate the required prologue. Make the FRAME_POINTER
config symbol depending on !clang.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Commit cafa0010cd ("Raise the minimum required gcc version to 4.6")
raised the minimum GCC version to 4.6. Old mcount is only required for
GCC versions older than 4.4.0. Hence old mcount support can be dropped
too.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Enable low-level debugging support for RZ/G1N (R8A7744). RZ/G1N uses
SCIF0 for the debug console.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Most of the SoC updates in this cycle are cleanups and moves to more
modern infrastructure:
- Davinci was moved to common clock framework
- OMAP1-based Amstrad E3 "Superphone" saw a bunch of cleanups to the
keyboard interface (bitbanged AT keyboard via GPIO).
- Removal of some stale code for Renesas platforms
- Power management improvements for i.MX6LL
-----BEGIN PGP SIGNATURE-----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=ACVk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 32-bit SoC platform updates from Olof Johansson:
"Most of the SoC updates in this cycle are cleanups and moves to more
modern infrastructure:
- Davinci was moved to common clock framework
- OMAP1-based Amstrad E3 "Superphone" saw a bunch of cleanups to the
keyboard interface (bitbanged AT keyboard via GPIO).
- Removal of some stale code for Renesas platforms
- Power management improvements for i.MX6LL"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (112 commits)
ARM: uniphier: select RESET_CONTROLLER
arm64: uniphier: select RESET_CONTROLLER
ARM: uniphier: remove empty Makefile
ARM: exynos: Clear global variable on init error path
ARM: exynos: Remove outdated maintainer information
ARM: shmobile: Always enable ARCH_TIMER on SoCs with A7 and/or A15
ARM: shmobile: r8a7779: hide unused r8a7779_platform_cpu_kill
soc: r9a06g032: don't build SMP files for non-SMP config
ARM: shmobile: Add the R9A06G032 SMP enabler driver
ARM: at91: pm: configure wakeup sources for ULP1 mode
ARM: at91: pm: add PMC fast startup registers defines
ARM: at91: pm: Add ULP1 mode support
ARM: at91: pm: Use ULP0 naming instead of slow clock
ARM: hisi: handle of_iomap and fix missing of_node_put
ARM: hisi: check of_iomap and fix missing of_node_put
ARM: hisi: fix error handling and missing of_node_put
ARM: mx5: Set the DBGEN bit in ARM_GPC register
ARM: imx51: Configure M4IF to avoid visual artifacts
ARM: imx: call imx6sx_cpuidle_init() conditionally for 6sll
ARM: imx: fix i.MX6SLL build
...
Move the source of lib/Kconfig.debug and arch/$(ARCH)/Kconfig.debug to
the top-level Kconfig. For two architectures that means moving their
arch-specific symbols in that menu into a new arch Kconfig.debug file,
and for a few more creating a dummy file so that we can include it
unconditionally.
Also move the actual 'Kernel hacking' menu to lib/Kconfig.debug, where
it belongs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Entries are sorted by their address value, except the BCM2836/KONA
which are not in the proper order.
Signed-off-by: Clément Peron <clement.peron@devialet.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Broadcom iProc SoCs typically use the UART3 for debug/console, provide a
known good location for that.
Signed-off-by: Clément Peron <clement.peron@devialet.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable low-level debugging support for RZ/G1C (r8a77470). RZ/G1C uses
SCIF1 for the debug console.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Without CONFIG_MMU, this results in a build failure:
./arch/arm/include/asm/memory.h:92:23: error: initializer element is not constant
#define VECTORS_BASE vectors_base
arch/arm/mm/dump.c:32:4: note: in expansion of macro 'VECTORS_BASE'
{ VECTORS_BASE, "Vectors" },
arch/arm/mm/dump.c:71:11: error: 'L_PTE_USER' undeclared here (not in a function); did you mean 'VTIME_USER'?
.mask = L_PTE_USER,
^~~~~~~~~~
Obviously the feature only makes sense with an MMU, so let's add the
dependency here.
Fixes: a8e53c151f ("ARM: 8737/1: mm: dump: add checking for writable and executable")
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Page mappings with full RWX permissions are a security risk.
x86, arm64 has an option to walk the page tables
and dump any bad pages.
(1404d6f13e
("arm64: dump: Add checking for writable and exectuable pages"))
Add a similar implementation for arm.
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
This patch refactors the arm page table dumping code,
so multiple tables may be registered with the framework.
This patch refers below commits of arm64.
(4674fdb9f1 ("arm64: mm: dump: make page table dumping reusable"))
(4ddb9bf833 ("arm64: dump: Make ptdump debugfs a separate option"))
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Laura Abbott <labbott@redhat.com>
Reviewed-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Jinbum Park <jinb.park7@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Pull ARM fixes from Russell King:
- LPAE fixes for kernel-readonly regions
- Fix for get_user_pages_fast on LPAE systems
- avoid tying decompressor to a particular platform if DEBUG_LL is
enabled
- BUG if we attempt to return to userspace but the to-be-restored PSR
value keeps us in privileged mode (defeating an issue that ftracetest
found)
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: BUG if jumping to usermode address in kernel mode
ARM: 8722/1: mm: make STRICT_KERNEL_RWX effective for LPAE
ARM: 8721/1: mm: dump: check hardware RO bit for LPAE
ARM: make decompressor debug output user selectable
ARM: fix get_user_pages_fast
Make the decompressor debug output user selectable, otherwise merely
enabling DEBUG_LL causes the decompressor to become board specific,
thereby preventing a multi-platform kernel from booting. Enabling
DEBUG_LL doesn't cause the kernel itself to become platform specific
unless EARLY_PRINTK is enabled, or one of the debugging routines is
added in a path that results in it being called.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are
OMAP, Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now
with a Quad-Core ARM Cortex-A7. According to the manufacturer,
it is intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family
of chips meant for managed gigabit ethernet switches, based
around a Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2
and Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jlJ2
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"Most of the commits are for defconfig changes, to enable newly added
drivers or features that people have started using. For the changed
lines lines, we have mostly cleanups, the affected platforms are OMAP,
Versatile, EP93xx, Samsung, Broadcom, i.MX, and Actions.
The largest single change is the introduction of the TI "sysc" bus
driver, with the intention of cleaning up more legacy code.
Two new SoC platforms get added this time:
- Allwinner R40 is a modernized version of the A20 chip, now with a
Quad-Core ARM Cortex-A7. According to the manufacturer, it is
intended for "Smart Hardware"
- Broadcom Hurricane 2 (Aka Strataconnect BCM5334X) is a family of
chips meant for managed gigabit ethernet switches, based around a
Cortex-A9 CPU.
Finally, we gain SMP support for two platforms: Renesas R-Car E2 and
Amlogic Meson8/8b, which were previously added but only supported
uniprocessor operation"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (118 commits)
ARM: multi_v7_defconfig: Select RPMSG_VIRTIO as module
ARM: multi_v7_defconfig: enable CONFIG_GPIO_UNIPHIER
arm64: defconfig: enable CONFIG_GPIO_UNIPHIER
ARM: meson: enable MESON_IRQ_GPIO in Kconfig for meson8b
ARM: meson: Add SMP bringup code for Meson8 and Meson8b
ARM: smp_scu: allow the platform code to read the SCU CPU status
ARM: smp_scu: add a helper for powering on a specific CPU
dt-bindings: Amlogic: Add Meson8 and Meson8b SMP related documentation
ARM: OMAP3: Delete an unnecessary variable initialisation in omap3xxx_hwmod_init()
ARM: OMAP3: Use common error handling code in omap3xxx_hwmod_init()
ARM: defconfig: select the right SX150X driver
arm64: defconfig: Enable QCOM_IOMMU
arm64: Add ThunderX drivers to defconfig
arm64: defconfig: Enable Tegra PCI controller
cpufreq: imx6q: Move speed grading check to cpufreq driver
arm64: defconfig: re-enable Qualcomm DB410c USB
ARM: configs: stm32: Add MDMA support in STM32 defconfig
ARM: imx: Enable cpuidle for i.MX6DL starting at 1.1
bus: ti-sysc: Fix unbalanced pm_runtime_enable by adding remove
bus: ti-sysc: mark PM functions as __maybe_unused
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
part), please pull the following:
- Florian adds support for the Broadcom Hurricane 2 SoC machine entry point
and defines the debug UART address for use with earlyprintk/DEBUG_LL
-----BEGIN PGP SIGNATURE-----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=OjEl
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.15/soc-part2' of http://github.com/Broadcom/stblinux into next/soc
Pull "Broadcom soc changes for 4.15 (part 2)" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoC changes for 4.15 (second
part), please pull the following:
- Florian adds support for the Broadcom Hurricane 2 SoC machine entry point
and defines the debug UART address for use with earlyprintk/DEBUG_LL
* tag 'arm-soc/for-4.15/soc-part2' of http://github.com/Broadcom/stblinux:
ARM: debug: Add Hurricane 2 UART2 debug addresses
ARM: bcm: Add support for Broadcom Hurricane 2 SoC
Broadcom Hurricane 2 SoCs typically use their secondary UART for
debug/console, provide a known good location for that.
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Enable low-level debugging support for RZ/G1E (r8a7745). RZ/G1E uses
SCIF4 for the debug console.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The legacy code to try to detect the debug_ll uart based on machine
is no longer needed, and we can remove it. Note that the Kconfig
options stay the same, we just need to define the port configuration
now.
-----BEGIN PGP SIGNATURE-----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=BLZK
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.14/debug-ll-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Pull "Updates to for omap debug_ll code to use generic DEBUG_UART_8250 code" from Tony Lindgren:
The legacy code to try to detect the debug_ll uart based on machine
is no longer needed, and we can remove it. Note that the Kconfig
options stay the same, we just need to define the port configuration
now.
* tag 'omap-for-v4.14/debug-ll-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: debug: Use generic 8250 debug_ll for am3517 and am335x
ARM: debug: Use generic 8250 debug_ll for ti81xx
ARM: debug: Use generic 8250 debug_ll for omap3/4/5
ARM: debug: Use generic 8250 debug_ll for omap2 and omap3/4/5 common uarts
Enable low-level debugging support for RZ/G1M (r8a7743). RZ/G1M uses
SCIF0 for the debug console, like most of the R-Car Gen2 SoCs.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
We want to use generic 8250 debug_ll code to get DEBUG_UNCOMPRESS
working and to simplify the code. The old debug_ll code is no longer
needed and the machine ID based detection is no longer used.
Note that for most part there's no need to keep DEBUG_LL enabled.
We now have CONFIG_SERIAL_EARLYCON working very early as long as
the kernel cmdline has "earlycon" in it and the board specific dts
file has chosen configured with with the port using stdout-path.
Cc: Hoeun Ryu <hoeun.ryu@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to use generic 8250 debug_ll code to get DEBUG_UNCOMPRESS
working and to simplify the code. The old debug_ll code is no longer
needed and the machine ID based detection is no longer used.
Note that for most part there's no need to keep DEBUG_LL enabled.
We now have CONFIG_SERIAL_EARLYCON working very early as long as
the kernel cmdline has "earlycon" in it and the board specific dts
file has chosen configured with with the port using stdout-path.
Cc: Hoeun Ryu <hoeun.ryu@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to use generic 8250 debug_ll code to get DEBUG_UNCOMPRESS
working and to simplify the code. The old debug_ll code is no longer
needed and the machine ID based detection is no longer used.
Note that for most part there's no need to keep DEBUG_LL enabled.
We now have CONFIG_SERIAL_EARLYCON working very early as long as
the kernel cmdline has "earlycon" in it and the board specific dts
file has chosen configured with with the port using stdout-path.
Cc: Hoeun Ryu <hoeun.ryu@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to use generic 8250 debug_ll code to get DEBUG_UNCOMPRESS
working and to simplify the code. The old debug_ll code is no longer
needed and the machine ID based detection is no longer used.
Note that for most part there's no need to keep DEBUG_LL enabled.
We now have CONFIG_SERIAL_EARLYCON working very early as long as
the kernel cmdline has "earlycon" in it and the board specific dts
file has chosen configured with with the port using stdout-path.
Cc: Hoeun Ryu <hoeun.ryu@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* Add debug UART addresses for IPQ4019
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=k14G
-----END PGP SIGNATURE-----
Merge tag 'qcom-soc-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/soc
Qualcomm ARM Based SoC Updates for v4.13
* Add debug UART addresses for IPQ4019
* tag 'qcom-soc-for-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
ARM: debug: qcom: add UART addresses to Kconfig help for IPQ4019
Signed-off-by: Olof Johansson <olof@lixom.net>
Add information about the IPQ4019 debug UART physical and virtual
addresses in the DEBUG_QCOM_UARTDM Kconfig help section.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add support for low level debugging on Atmel samv7x.
Signed-off-by: Szemző András <sza@esh.hu>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
RK1108 UARTs are Synopsis DesignWare 8250 compatible.
Only with different register addresses.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Jacob Chen <jacob2.chen@rock-chips.com>
[rk1108->rv1108 rename]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
There are multiple architectures that support CONFIG_DEBUG_RODATA and
CONFIG_SET_MODULE_RONX. These options also now have the ability to be
turned off at runtime. Move these to an architecture independent
location and make these options def_bool y for almost all of those
arches.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Clean-up:
* Only use smp_init when SMP is selected
Enablement:
* Add debug-ll support for r8a7992
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Opm
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Pull "Renesas ARM Based SoC Updates for v4.9" from Simon Horman:
Clean-up:
* Only use smp_init when SMP is selected
Enablement:
* Add debug-ll support for r8a7992
* tag 'renesas-soc-for-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: only use smp_init when SMP is selected
ARM: shmobile: r8a7790: only use smp_init when SMP is selected
ARM: debug-ll: Add support for r8a7992
Enable low-level debugging support for R-Car V2H (r8a7792).
V2H uses SCIF0 for the debug console, like most other R-Car Gen2 SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The SUN_TOP_CTRL_FAMILY_ID register is at a fixed absolute address for
all of our supported chips, so utilize its value to determine what the
UARTA base address should be based on the value we read.
Since the code is called both during decompressor when the MMU is off,
and after the MMU has been turned on in the kernel, and we want to do
the lookup only once, we use the same technique as tegra.S and have a
shared storage location between the decompressor and the kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Merge "the second part of the Broadcom ARM-based SoC changes" from Florian Fainelli:
- Florian updates the DEBUG_UART_BCM5301X entry to cover both NS and NSP SoCs
since they both have the same location
* tag 'arm-soc/for-4.8/soc-part2' of http://github.com/Broadcom/stblinux:
ARM: debug: Enable DEBUG_BCM_5301X for Northstar Plus SoCs
Northstar Plus SoCs (ARCH_BCM_NSP) have the exact same UART location and
properties like the register shift of 0, so make it usable.
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add configuration options for the most commonly used UART physical and
virtual addresses to ease the use of DEBUG_LL and earlyprintk.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
AT91 still uses an offset (0x0100 0000) from the physical address to map
the debug UART. This is unfortunate as for some platforms (sama5d3 and
earlier), it ends up in the PCI zone and PCI is enabled in multi_v7.
Switch to DEBUG_UART_VIRT to solve that.
Tested on sama5d3 and 9g20.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DEBUG_HI3716_UART was supposed to be renamed to DEBUG_HIX5HD2_UART, but
accidentally both got left in place, which results in a build error when
CONFIG_DEBUG_UART_PHYS is not set as it should be.
This removes the old symbol.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 12aae30974 ("ARM: debug: Rename Hi3716 to HIX5HD2")
Acked-by: Wei Xu <xuwei5@hisilicon.com>
Some SoCs use a Palmchip BK-310x UART which is mostly 16550 compatible
but with a different register layout. While this UART has previously
only been supported in MIPS based chips (Alchemy, Ralink), the ARM based
SMP87xx series from Sigma Designs also uses it.
This patch allows the debug console to work with this type of UART.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
A few fixes for fallout that we didn't catch in time in -next, or smaller
warning fixes that have been discovered since.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PRjJ
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for fallout that we didn't catch in time in -next, or
smaller warning fixes that have been discovered since"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
soc: qcom/spm: shut up uninitialized variable warning
ARM: realview: fix device tree build
ARM: debug-ll: fix BCM63xx entry for multiplatform
ARM: dts: armadillo800eva Correct extal1 frequency to 24 MHz
Linus Walleij