The Amlogic P212 reference design is used by other devices as well, such
as (for example) the Khadas VIM boards. Thus this patch adds and moves
all common entries from meson-gxl-s905x-p212.dts to a new, separate
meson-gxl-s905x-p212.dtsi (which can be re-used on boards such as the
Khadas VIM).
Support for all boards based on the P212 reference design includes:
- enabling IR support
- enabling the SAR ADC (SARADC_CH1 is connected to a resistor which
indicates the hardware revision, a similar design is found on the
Khadas VIM boards)
- all MMC controllers (which means that SDIO wifi, the SD card and the
eMMC are now supported)
- pwm_ef as dependency for the SDIO wifi modules
- uart_A which is connected to the bluetooth module (the bluetooth
module itself is not enabled yet due to missing devicetree bindings
for the Broadcom serial bluetooth devices)
- uart_AO is moved to the .dtsi (as all known devices use it as their
boot-console)
Specific to the P212 board:
- this also enables the CVBS connector (which is not available on the
Khadas VIM boards for example)
- Realtek based SDIO wifi (instead of Broadcom which most other devices
use)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds support for the HwaCom AmazeTV set-top-box. The
hardware configuration is really similar to the other GXL boards but
for this hardware we need to limit the max-frequency of the eMMC to
have it working.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The ethmac node has to be configured for each board due to different
pinctrl nodes for RGMII/RMII. Thus the phy-mode should be specified at
the same place (= in the board .dts), making it easier to read the board
.dts file (because the phy-mode is stated explicitly, without requiring
developers to read all "parent" .dtsi as well).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the amlogic,tx-delay-ns property with the old (hardcoded)
default value of 2ns to all boards which are using an RGMII ethernet
PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Amlogic's own .dts specifies that the P201 board uses a RMII PHY (with
the reset GPIO being GPIOZ_14).
However our P201 board .dts simply inherits the phy-mode setting from
from meson-gx.dtsi where it defaults to RGMII mode.
Remove all ethernet settings from meson-gxbb-p20x.dtsi as it only
specifies the RGMII pins which are only valid for the P200 board.
Instead we add the ethmac node to the meson-gxbb-p201.dts and configure
the pinctrl property and the phy-mode for an RMII PHY.
An MDIO node (which would also specify the PHY) is not added since we
don't know which PHY is being used (and thus which PHY address would
have to be used).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This resets the ethernet PHY during boot to get the PHY into a "clean"
state.
While here also specify the phy-handle of the ethmac node to make the
PHY configuration similar to the one we have on GXL devices. This will
allow us to specify OF-properties for the PHY itself.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This resets the ethernet PHY during boot to get the PHY into a "clean"
state. While here also explicitly specify the phy-mode instead of
relying on the default-value from meson-gx.dtsi.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Merge "ARMv8 Juno DT fix for v4.11" from Sudeep Holla:
Just single patch to fix replicator in order to prevent overflows at
the source and reduce the back pressure by splitting the trace output
to TPIU and ETR.
* tag 'juno-fixes-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: update definition for programmable replicator
ARM64 DT updates are fairly small this time, only two new SoCs and a handful
of new machines get added, all of them similar to other hardware we already
support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner: MMC, USB
ARM Juno: Coresight, STM
Broadcom: NS2 GICv2m irqchip and PCIe
Marvell: Armada 3700 SPI, I2C, ethernet switch
Mediatek: MT8173 thermal
NXP i.MX: LS1046A thermal
Qualcomm: coresight on MSM8916, HDMI, WCNSS, SCM
Renesas: r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip: thermal, eDP, pinctrl enhancements
Samsung: TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier: SD reset, eMMC controller
ZTE: oppv2 cpufreq
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIUAwUAWK9htWCrR//JCVInAQL5sg/40ehZk89xuReYHaOoL0jkEGxt7ogae2Q0
5SurlVNEjkr1A6KKcTKwy6c8E4GReq0ioVUxyYHlNo2MedtLQWssSvObfjt390E+
OYXhuHHyHFgut9jF6nq1IZbSqkhaDcoRFdK0EPzjdxTMMk59xqzG2t9Kbq0MFz0I
Fg0+xB44VAOwuM+45MjNzdpTzolkH3gxlK4TV/opbr2/9uEDCjFOLr1zqZuWqIDh
uyXXqHYUZ54kz2GvhfYPgcm+f+PjuV2fw/Jh5u3+jNvwMQvA70Erv52im1o1a3GV
UTjmBgccTKByrPk7gXP3lgRkHQGwPLNH0L+28AZ/BNuZbWqDrDe7uVfpq9nWb5Xl
IR0uleNBOuiOdqR6Ya4xosGSm6AOgQhCbE52trHdUhb03eqRbqHcLHEVmZXXea/i
EejGOciIvbV8ent9jjREw/kvGZ+Ws6v5notG4uPDwn+YZSJAyqvGh5Tul8WzZIxk
Wr1WZgbuwkI0KYiFzSINfgDX0Om2l6YoVZLnkjst5Exto+TGRSINJpVCXsuGIU7O
34qZD25yA8WlJTooBL0cvrW0NT2RewBqLogwhbwDnRW241SW5AnuzPsFPWldLzon
L5sFgsF60gWiIlbB2/BKdpF2jB/+brXNR6epnQYADigweg/4+pS8HPZRFj7g8wyE
s22+OYJ6Cg==
=glug
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Arnd Bergmann:
"ARM64 DT updates are fairly small this time, only two new SoCs and a
handful of new machines get added, all of them similar to other
hardware we already support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards:
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64:
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K:
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner:
- MMC, USB
ARM Juno:
- Coresight, STM
Broadcom:
- NS2 GICv2m irqchip and PCIe
Marvell:
- Armada 3700 SPI, I2C, ethernet switch
Mediatek:
- MT8173 thermal
NXP i.MX:
- LS1046A thermal
Qualcomm:
- coresight on MSM8916, HDMI, WCNSS, SCM
Renesas:
- r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip:
- thermal, eDP, pinctrl enhancements
Samsung:
- TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier:
- SD reset, eMMC controller
ZTE:
- oppv2 cpufreq"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits)
arm64: dts: qcom: Add msm8916 CoreSight components
arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
arm64: allwinner: add BananaPi-M64 support
arm64: allwinner: a64: add UART1 pin nodes
arm64: allwinner: pine64: add MMC support
arm64: allwinner: a64: Increase the MMC max frequency
arm64: allwinner: a64: Add MMC pinctrl nodes
arm64: allwinner: a64: Add MMC nodes
dt-bindings: clockgen: Add compatible string for LS1012A
Documentation: DT: add LS1012A compatible for SCFG and DCFG
Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards
arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci
arm64: tegra: Use symbolic reset identifiers
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
...
Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and dwc
and xhci controllers, new device ids, new phy drivers, a new usb-serial
driver, and a few other minor changes in different USB drivers.
All have been in linux-next for a long time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWK2lrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykh7ACffotTJvB/gwpuSIWh6qhA8KQ9mH8AnjlxMafv
b5b3vfOXJ8/N0Go25VwI
=7fqN
-----END PGP SIGNATURE-----
Merge tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver updates for 4.11-rc1.
Nothing major, just the normal amount of churn in the usb gadget and
dwc and xhci controllers, new device ids, new phy drivers, a new
usb-serial driver, and a few other minor changes in different USB
drivers.
All have been in linux-next for a long time with no reported issues"
* tag 'usb-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (265 commits)
usb: cdc-wdm: remove logically dead code
USB: serial: keyspan: drop header file
USB: serial: io_edgeport: drop io-tables header file
usb: musb: add code comment for clarification
usb: misc: add USB251xB/xBi Hi-Speed Hub Controller Driver
usb: misc: usbtest: remove redundant check on retval < 0
USB: serial: upd78f0730: sort device ids
USB: serial: upd78f0730: add ID for EVAL-ADXL362Z
ohci-hub: fix typo in dbg_port macro
usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS
usb: musb: tusb6010: Clean up tusb_omap_dma structure
usb: musb: cppi_dma: Clean up cppi41_dma_controller structure
usb: musb: cppi_dma: Clean up cppi structure
usb: musb: cppi41: Detect aborted transfers in cppi41_dma_callback()
usb: musb: dma: Add a DMA completion platform callback
drivers: usb: usbip: Add missing break statement to switch
usb: mtu3: remove redundant dev_err call in get_ssusb_rscs()
USB: serial: mos7840: fix another NULL-deref at open
USB: serial: console: clean up sanity checks
USB: serial: console: fix uninitialised spinlock
...
Juno platforms have a programmable replicator splitting the trace output
to TPIU and ETR. Currently this is not being programmed as it is being
treated as a none-programmable replicator - which is the default
operational mode for these devices. The TPIU in the system is enabled by
default, and this combination is causing back-pressure in the trace
system resulting in overflows at the source.
Replaces the existing definition with one that defines the programmable
replicator, using the "qcom,coresight-replicator1x" driver that provides
the correct functionality for CoreSight programmable replicators.
Reviewed-and-Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
1. Add necessary initial configuration for clocks of display subsystem.
Till now it worked mostly thanks to bootloader.
2. Use macro definitions instead of hard-coded values for pinctrl on Exynos7.
3. Enable USB 3.0 (DWC3) on Exynos7.
-----BEGIN PGP SIGNATURE-----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=02Sx
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/late
Pull "Samsung DeviceTree ARM64 update for v4.11, third round" from Krzysztof Kozłowski:
1. Add necessary initial configuration for clocks of display subsystem.
Till now it worked mostly thanks to bootloader.
2. Use macro definitions instead of hard-coded values for pinctrl on Exynos7.
3. Enable USB 3.0 (DWC3) on Exynos7.
* tag 'samsung-dt64-4.11-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (27 commits)
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
clk: samsung: exynos5433: Add data for 250MHz and 278MHz PLL rates
clk: samsung: exynos5433: Add IDs for PHYCLK_MIPIDPHY0_* clocks
arm64: dts: exynos: Add clocks to Exynos5433 LPASS module
arm64: dts: exynos: set LDO7 regulator as always on
arm64: dts: exynos: configure TV path clocks for Ultra HD modes
arm64: dts: exynos: Fix drive strength of sd0_xxx pin definitions
arm64: dts: exynos: Disable pull down for audio pins in Exynos5433 SoCs
arm64: dts: exynos: Add TM2 touchkey node
arm64: dts: exynos: Remove unneeded unit names in Exynos5433 nodes
arm64: dts: exynos: Enable HDMI/TV path on Exynos5433-TM2
arm64: dts: exynos: Add HDMI node to Exynos5433
arm64: dts: exynos: Add DECON_TV node to Exynos5433
arm64: dts: exynos: Fix addresses in node names on Exynos5433
arm64: dts: exynos: Make TM2 and TM2E independent from each other
arm64: dts: exynos: Fix wrong values for ldo23 and ldo25 on TM2/TM2E
...
adjust name of sd-mmc-gop clock in sysco for Armada 7K/8K
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWJCWUCMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71YLYAJsGQxfg30DY
invLPTtpT7c8xBx/7gCeKmbV8qgukU7rq9L1/T3OeLrPqTI=
=2tUY
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.11-3' of git://git.infradead.org/linux-mvebu into next/dt64
Pull "mvebu dt for 4.11 (part 3)" from Gregory CLEMENT:
adjust name of sd-mmc-gop clock in sysco for Armada 7K/8K
* tag 'mvebu-dt64-4.11-3' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
Some patches related the arm64 Allwinner SoCs, most notably:
- Support for the MMC
- Suport for the USB and mUSB controllers
- New boards: Bananapi M64
-----BEGIN PGP SIGNATURE-----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=//in
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt64
Pull "Allwinner arm64 changes for 4.11" from Maxime Ripard:
Some patches related the arm64 Allwinner SoCs, most notably:
- Support for the MMC
- Suport for the USB and mUSB controllers
- New boards: Bananapi M64
* tag 'sunxi-dt64-for-4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
arm64: allwinner: add BananaPi-M64 support
arm64: allwinner: a64: add UART1 pin nodes
arm64: allwinner: pine64: add MMC support
arm64: allwinner: a64: Increase the MMC max frequency
arm64: allwinner: a64: Add MMC pinctrl nodes
arm64: allwinner: a64: Add MMC nodes
arm64: dts: allwinner: Remove no longer used pinctrl/sun4i-a10.h header
arm64: dts: enable the MUSB controller of Pine64 in host-only mode
arm64: dts: add MUSB node to Allwinner A64 dtsi
arm64: dts: allwinner: enable EHCI1, OHCI1 and USB PHY nodes in Pine64
arm64: dts: allwinner: sort the nodes in sun50i-a64-pine64.dts
arm64: dts: allwinner: add USB1-related nodes of Allwinner A64
Due to the reference clock comes from 26M oscillator directly
on mt8173, and it is a fixed-clock in DTS which always turned
on, we ignore it before. But on some platforms, it comes
from PLL, and need be controlled, so here add it, no matter
it is a fixed-clock or not.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding fixed voltage regulators for Vbus and Vbus-boost required
by USB 3.0 DRD controller on Exynos7-espresso board.
Signed-off-by: Vivek Gautam <gautamvivek1987@gmail.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add USB 3.0 DRD controller device node, with its clock
and phy information to enable the same on Exynos7.
Signed-off-by: Vivek Gautam <gautamvivek1987@gmail.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add initial set of CoreSight components found on Qualcomm msm8916 and
apq8016 based platforms, including the DragonBoard 410c board.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add initial clock configuration for display subsystem for Exynos5433
based TM2/TM2e boards in device tree in order to avoid dependency on the
configuration left by the bootloader. This initial configuration is also
needed to ensure that display subsystem is operational if display power
domain gets turned off before clock controller is probed and the inital
clock configuration left by the bootloader saved.
TM2 and TM2e uses different rate for DISP PLL clock, but for better
maintainability all 'assigned-clocks-*' properties for DISP CMU are
defines in each board dts instead of redefining the rates property.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This commit adjusts the names of gatable clock #18 of the Marvell Armada
CP110 system controller. This clock not only controls SD/MMC, but also
the GOP (Group Of Ports) used for networking. So the clock is renamed to
{cpm,cps}-sd-mmc-gop instead of {cpm,cps}-sd-mmc.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
1. Use proper drive strengths on Exynos7.
2. Fix significant current leak on Exynos5433-based TM2/TM2E due
to disabled regulator.
3. Add touchkey to TM2, set display clocks for Ultra HD modes.
4. Cleanups and minor fixes for Exynos5433, TM2 and TM2E.
-----BEGIN PGP SIGNATURE-----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=rfRv
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt64-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt64
Samsung DeviceTree ARM64 update for v4.11, second round:
1. Use proper drive strengths on Exynos7.
2. Fix significant current leak on Exynos5433-based TM2/TM2E due
to disabled regulator.
3. Add touchkey to TM2, set display clocks for Ultra HD modes.
4. Cleanups and minor fixes for Exynos5433, TM2 and TM2E.
* tag 'samsung-dt64-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: Add clocks to Exynos5433 LPASS module
arm64: dts: exynos: set LDO7 regulator as always on
arm64: dts: exynos: configure TV path clocks for Ultra HD modes
arm64: dts: exynos: Fix drive strength of sd0_xxx pin definitions
arm64: dts: exynos: Disable pull down for audio pins in Exynos5433 SoCs
arm64: dts: exynos: Add TM2 touchkey node
arm64: dts: exynos: Remove unneeded unit names in Exynos5433 nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the 5 buttons connected to a resistor laddered matrix and sampled
by the SAR ADC channel 0.
Only the p200 board has these buttons, the P201 doesn't.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the SAR ADC to meson-gxbb.dtsi and meson-gxl.dtsi. GXBB provides a
10-bit ADC while GXL and GXM provide a 12-bit ADC.
Some boards use resistor ladder buttons connected through one of the ADC
channels. On newer devices (GXL and GXM) some boards use pull-ups/downs
to change the resistance (and thus the ADC value) on one of the ADC
channels to indicate the board revision.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Banana Pi M64 board is a typical single board computer based on the
Allwinner A64 SoC. Aside from the usual peripherals it features eMMC
storage, which is connected to the 8-bit capable SDHC2 controller.
Also it has a soldered WiFi/Bluetooth chip, so we enable UART1 and SDHC1
as those two interfaces are connected to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
On many boards UART1 connects to a Bluetooth chip, so add the pinctrl
nodes for the only pins providing access to that UART. That includes
those pins for hardware flow control (RTS/CTS).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
All Pine64 boards connect an micro-SD card slot to the first MMC
controller.
Enable the respective DT node and specify the (always-on) regulator
and card-detect pin.
As a micro-SD slot does not feature a write-protect switch, we disable
this feature.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The eMMC controller seem to have a maximum frequency of 200MHz, while the
regular MMC controllers are capped at 150MHz.
Since older SoCs cannot go that high, we cannot change the default maximum
frequency, but fortunately for us we have a property for that in the DT.
This also has the side effect of allowing to use the MMC HS200 and SD
SDR104 modes for the boards that support it (with either 1.2v or 1.8v IOs).
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A64 only has a single set of pins for each MMC controller. Since we
already have boards that require all of them, let's add them to the DTSI.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The A64 has 3 MMC controllers, one of them being especially targeted to
eMMC. Among other things, it has a data strobe signal and a 8 bits data
width.
The two other are more usual controllers that will have a 4 bits width at
most and no data strobe signal, which limits it to more usual SD or MMC
peripherals.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Florian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: Chen-Yu Tsai <wens@csie.org>
- Enable cpufreq support for zx296718 by using new operating-points-v2
bindings, so that it works with the generic cpufreq-dt driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYjW1hAAoJEFBXWFqHsHzOkYUH/RNoyrOb3+KWfy0pczLBj98F
SmF966hsGNPPKNZ+NFhqWdd1/iT9UzdIax09858HQzvyWSL7LSZNwbkHJU/2McKy
zFo71IAnMNiNti6USiKVNX0HGx9ndnCChzJBUAcum46fJ7Kt0g8zjfBZfGjRq1cQ
b3b1sJXt5P9+ebjUhrGXAykkS4zwpTHCdRAwmtKQEhU8Q5ri2+pqMtwvrt8XDfxl
vFbckTpA0byd60TGvl/HecmafpYhXvOU7QGQaknzOnlH2o5dmwf0/i7Cw0sqyQn7
JeBopKi7N2S2hN7ZlUYcEQ87FRGdf2u5WbQtcTRiYrZwvUf508hNMxGclMKUHNg=
=EYrK
-----END PGP SIGNATURE-----
Merge tag 'zte-dt64-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
ZTE arm64 device tree update for 4.11:
- Enable cpufreq support for zx296718 by using new operating-points-v2
bindings, so that it works with the generic cpufreq-dt driver.
* tag 'zte-dt64-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: zx: support cpu-freq for zx296718
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add support for LS1012A SoC which is an ARMv8 SoC with single
Cortex-A53 core, and the corresponding board support: FRDM, QDS
and RDB.
- Enable TMU (Thermal Monitoring Unit) support for LS1046A SoC.
- Enable PCA9547 device for ls2080a-rdb board by removing 'disabled'
status setting.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYjWZxAAoJEFBXWFqHsHzOvGQIAJpdglbg/r997PFL43gODNaU
RfF/userRtzsm3PZ9Uyf2EMg2Q66O92g9lqlr6+QNDSBuLl6iyyIomiCE3P9D/8A
IggNiTKYuEFqWQUCQL6VSoOK5Ha9sa4D23rrGoRGbfKeiiM8M/gn7gNjOAmbbZx6
VwVAAmkLObGmrkxq9IN++u7rIpTWLyOX+6wzQUYFfTD8OqGBrkpFpKOGTZXgzmeE
Q8EebPh/ti2lFjGw1lWECjI4kEXIz7TMnKFsS/fYf7o6s778JQ/uocUl2UtTon1E
aIIU72OMq6Mp/EoaMq3l9t1pgoEZMPVzyGiYPVypfEzkKTh26wb9POc6KiDO0JE=
=g8mg
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Freescale arm64 device tree updates for 4.11:
- Add support for LS1012A SoC which is an ARMv8 SoC with single
Cortex-A53 core, and the corresponding board support: FRDM, QDS
and RDB.
- Enable TMU (Thermal Monitoring Unit) support for LS1046A SoC.
- Enable PCA9547 device for ls2080a-rdb board by removing 'disabled'
status setting.
* tag 'imx-dt64-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: clockgen: Add compatible string for LS1012A
Documentation: DT: add LS1012A compatible for SCFG and DCFG
Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards
arm64: dts: ls1046a: Add TMU device tree support
arm64: dts: Add support for FSL's LS1012A SoC
arm64: dts: ls2080a-rdb: remove disable status of pca9547
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add a new Armada 8K based board: MACCHIATOBin
- Enable AHCI on the Armada 7K/8K SoCs
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWIt9MyMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71Zw/AJ9NEi6v2zy2
F16VJxKCgnhcJd++zwCfXA4/Z8eBtxXwsIPNLPMCTc9FtC0=
=JDKj
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.11-2' of git://git.infradead.org/linux-mvebu into next/dt64
mvebu dt64 for 4.11 (part 2)
- Add a new Armada 8K based board: MACCHIATOBin
- Enable AHCI on the Armada 7K/8K SoCs
* tag 'mvebu-dt64-4.11-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci
arm64: dts: marvell: Add DT for MACCHIATOBin board
Signed-off-by: Olof Johansson <olof@lixom.net>
This contains three patches that reintroduce symbolic identifiers for
clocks, resets and mailboxes. These had been converted to literals in
the v4.10 release to avoid complicated dependencies between branches.
-----BEGIN PGP SIGNATURE-----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=eeee
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.11-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt64
arm64: tegra: Device tree changes for v4.11-rc1
This contains three patches that reintroduce symbolic identifiers for
clocks, resets and mailboxes. These had been converted to literals in
the v4.10 release to avoid complicated dependencies between branches.
* tag 'tegra-for-4.11-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Use symbolic reset identifiers
arm64: tegra: Use symbolic clock identifiers
arm64: tegra: Use symbolic HSP identifiers
Signed-off-by: Olof Johansson <olof@lixom.net>
r8a779[56] SoCs:
* Mark EthernetAVB device node disabled in DT for r8a779[56] SoCs
- They are enabled as appropriate in board DT files
* Link ARM GIC to clock and clock domain on r8a779[56] SoCs
* Add thermal support
r8a7795 SoC:
* Tidyup audma definition order on r8a7795 SoC
* Add missing power-domains property for SATA
r8a7795/h3ulcb board:
* Add MIX/CTU support as per support present in DT for r8a7796
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KG8o
-----END PGP SIGNATURE-----
Merge tag 'renesas-arm64-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Second Round of Renesas ARM64 Based SoC DT Updates for v4.11
r8a779[56] SoCs:
* Mark EthernetAVB device node disabled in DT for r8a779[56] SoCs
- They are enabled as appropriate in board DT files
* Link ARM GIC to clock and clock domain on r8a779[56] SoCs
* Add thermal support
r8a7795 SoC:
* Tidyup audma definition order on r8a7795 SoC
* Add missing power-domains property for SATA
r8a7795/h3ulcb board:
* Add MIX/CTU support as per support present in DT for r8a7796
* tag 'renesas-arm64-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add missing power-domains property for sata
arm64: dts: h3ulcb: follow sound CTU/MIX supports
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add binding for Hi3660 SoC and HiKey960 Board
- Add binding for ARM Cortex-A73
- Add dts files for HiKey960 development board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zJLi
-----END PGP SIGNATURE-----
Merge tag 'hisi-arm64-dt-for-4.11' of git://github.com/hisilicon/linux-hisi into next/dt64
ARM64: DT: Hisilicon SoC DT updates for 4.11
- Add binding for Hi3660 SoC and HiKey960 Board
- Add binding for ARM Cortex-A73
- Add dts files for HiKey960 development board
* tag 'hisi-arm64-dt-for-4.11' of git://github.com/hisilicon/linux-hisi:
arm64: dts: Add dts files for Hisilicon Hi3660 SoC
dt-bindings: Add a support cpu type for cortex-a73
document: dt: add binding for Hi3660 SoC
Signed-off-by: Olof Johansson <olof@lixom.net>
- set mm_sel clock to 400 MHz to support 4K HDMI
- adjust power efficiency between the little and big cores
- add a node for thermal calibration via e-fuse data
-----BEGIN PGP SIGNATURE-----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=hboI
-----END PGP SIGNATURE-----
Merge tag 'v4.10-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt64
For mt8173:
- set mm_sel clock to 400 MHz to support 4K HDMI
- adjust power efficiency between the little and big cores
- add a node for thermal calibration via e-fuse data
* tag 'v4.10-next-dts' of https://github.com/mbgg/linux-mediatek:
arm64: dts: mt8173: add node for thermal calibration
arm64: dts: mt8173: Fix cpu_thermal cooling-maps contributions
arm64: dts: mt8173: add mmsel clocks for 4K support
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add Vol+ support for DB820C and APQ8016
* Add HDMI audio support for APQ8016
* Fix DB820C GPIO pinctrl name
* Enable WCNSS on MSM8916
* Add SCM node for MSM8996
* Use fixed XO clock on MSM8916
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=UglA
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt64
Qualcomm ARM64 Updates for v4.11
* Add Vol+ support for DB820C and APQ8016
* Add HDMI audio support for APQ8016
* Fix DB820C GPIO pinctrl name
* Enable WCNSS on MSM8916
* Add SCM node for MSM8996
* Use fixed XO clock on MSM8916
* tag 'qcom-arm64-for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: db820c: add support to volume up key
arm64: dts: apq8016-sbc: Limit MPP4 high state to 1.8V
arm64: dts: apq8016-sbc: Add Volume Up key device node
arm64: dts: apq8016-sbc: add support to hdmi audio via adv7533
arm64: dts: db820c: fix gpio pinctrl name correctly
ARM: dts: msm8916: Add and enable wcnss node
arm64: dts: msm8996: Add SCM DT node
arm64: dts: qcom: msm8916: Use fixed factor xo clock
Signed-off-by: Olof Johansson <olof@lixom.net>
usb clocks, grf phandles for the rk3399 CRUs, epd pinctrl settings,
a phandle to the rk3399 tsadc and converting boards to use the
recently introduced pin constants.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAliBUMUQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgeszCAC0VNLtUhe6ksHGJzvgP1diZLPghPsKticu
tmpxFVJrZTYFmxacvO3w2rXNvwtWsay812m+wmpbCYe2rpE1WwRYEhDIVbQ0hIuD
I7fiG6wKaGVEu+5XmVi+6tGouGKSZA0zBlcOja4kFeBPsyDDL0SISu1iopfD/o0z
u/2EfcBRQFLUotLKLY8t//I+RJ4IsDMQ4zh1AJ1NDfUVCqthE7sJzoa8eJuHaKjj
YPKdfJlUIZAXJiXuDrjrkkbUQT0GuYha0CtWE2nUn4clfrIWivvgJCXFfEnKtM9+
OguqMChemOXL7SanHGKqM4RHL6Qq0F3Y162UODDX2AC3QYxxv8XK
=i0J0
-----END PGP SIGNATURE-----
Merge tag 'v4.11-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
64bit dts changes with some adjustments to the pcie controller,
usb clocks, grf phandles for the rk3399 CRUs, epd pinctrl settings,
a phandle to the rk3399 tsadc and converting boards to use the
recently introduced pin constants.
* tag 'v4.11-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: add rockchip,grf property for RK3399 PMUCRU/CRU
arm64: dts: rockchip: add aspm-no-l0s for rk3399
arm64: dts: rockchip: add max-link-speed for rk3399
arm64: dts: rockchip: use pin constants to describe gpios
arm64: dts: rockchip: add u2phy clock for ehci and ohci of rk3399
arm64: dts: rockchip: add rk3399 eDP HPD pinctrl
arm64: dts: rockchip: add rk3399 thermal_zones phandle
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the pwm_ao_b pin to allow boards which have an LED connected
to GPIOAO_9 to use the leds-pwm driver (by activating the pwm_AO_ab node
and passing the pwm_ao_b_pin pinctrl-reference).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All Meson GX SoCs (GXBB, GXL and GXM) have a PWM controller within the
AO domain. When one of the board's LEDs is connected to one of the AO
PWM pins then this can be used to dim that LED (when the leds-pwm driver
is used).
Add the pwm_AO_ab to allow such devices to use the leds-pwm driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic Meson GXBB/GXL/GXM secure monitor uses part of the memory space,
this patch adds these reserved zones.
Without such reserved memory zones, running the following stress command :
$ stress-ng --vm 16 --vm-bytes 128M --timeout 10s
multiple times:
Could lead to the following kernel crashes :
[ 46.937975] Bad mode in Error handler detected on CPU1, code 0xbf000000 -- SError
...
[ 47.058536] Internal error: Attempting to execute userspace memory: 8600000f [#3] PREEMPT SMP
...
Instead of the OOM killer.
Fixes: 4f24eda840 ("ARM64: dts: Prepare configs for Amlogic Meson GXBaby")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
[khilman: added Fixes tag, added _reserved and unit addresses]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Martin Blumenstingl