For some unknown reason the parameters for snd_soc_test_bits() were in wrong
order:
It was:
snd_soc_test_bits(codec, val, mask, reg); /* WRONG!!! */
while it should be:
snd_soc_test_bits(codec, reg, mask, val);
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Currently the second tlv320aic3x instance fails to
be probed from DT if the reset pin is shared with
the first one.
This patch fixes it by moving the list add of the
reset pin into the i2c_probe method.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
For some CODEC drivers like who act as the MFDs children are ignored
by this patch.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
if codec driver is used for AIC3X_MODEL_3007 the mono iout controls overwrite
registers for class-d amplifier.
classd amplifier controls are only used for AIC3X_MODEL_3007.
Removing all mono snd_kcontrol_new, snd_soc_dapm_widget, snd_soc_dapm_route
and aic3x_init stuff from common code and call only for not AIC3X_MODEL_3007
codecs.
Testet only with AIC3X_MODEL_3007
Signed-off-by: Jan Weitzel <j.weitzel@phytec.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
'of_match_ptr' is defined in linux/of.h. Include it explicitly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The two paths were not connected in the DAPM route causing the associated
routes to be non working and the following warnings printed in the logs:
tlv320aic3x-codec 0-001b: ASoC: mux Right Line1L Mux has no paths
tlv320aic3x-codec 0-001b: ASoC: mux Left Line1R Mux has no paths
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is slightly more complex than a standard regmap conversion due to
the moderately detailed cache control and the open coding of a register
patch for the class D speaker on the TLV320AIC3007.
Although the device supports paging this is not currently implemented as
the additional pages are only used during the application of the patch
for the TLV320AIC3007.
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than referencing the cache directly read back the values we are
going to restore, supporting refactoring to use regmap.
Signed-off-by: Mark Brown <broonie@linaro.org>
Every statement in this comment is incorrect either through bitrot or
(mostly) through never having corresponded to reality in the first place.
Signed-off-by: Mark Brown <broonie@linaro.org>
We use the same 3 lines to get the CODEC for a kcontrol in a quite a few places.
This patch puts them into a common helper function. Having this encapsulated in
a helper function will also make it more easier to eventually change the data
layout of the kcontrol's private data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use snd_soc_dapm_mixer_update_power() instead of reimplementing its
functionality.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver supports a range of devices but currently doesn't allow those
device names to be used for enumeration on DT. Add the currently listed
I2C IDs as compatible strings.
Signed-off-by: Mark Brown <broonie@linaro.org>
When calling snd_soc_dapm_sync(), it eventually tries to lock the same mutex
already locked in snd_soc_dapm_put_volsw_aic3x() and a deadlock occurs. By
moving the mutex unlock to just before snd_soc_dapm_sync(), this deadlock is
prevented. This problem was introduced in Linux 3.5
Signed-off-by: Andreas Irestål <Andreas.Irestal@axis.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert MicBias widgets to supply widget.
On tlv320aic3x, Mic bias power on/off shares the same register bits
with output mic bias voltage. So, when power on mic bias, we need
reclaim it to voltage value.
Provide a new platform data so that the micbias voltage can be sent
according to board requirement. Now since tlv320aic3x codec driver
is DT aware, update dt files and functions to handle this new
"micbias-vg" platform data.
Because of sharing of bits, when enabling the micbias, voltage also
needs to be updated. So use SND_SOC_DAPM_POST_PMU & SND_SOC_DAPM_PRE_PMD
macro to create an event to handle this.
Since micbias is converted to supply widget, updated machine drivers as
well.
This change is runtime tested on da850-evm with audio loopback
(arecord|aplay) for confirmation.
Signed-off-by: Hebbar Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Device tree support for tlv320aic3x CODEC driver.
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
module_i2c_driver makes the code simpler by eliminating module_init
and module_exit calls.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This has been a pretty quiet release - very little activity in framework
terms, mostly just a few new drivers and updates:
- Added the ability to add and remove DAPM paths dynamically, mostly for
reparenting on clock changes.
- New machine drivers for Marvell Brownstone, ST-Ericsson Ux500
reference platform and ttc-dkp.
- New CPU drivers for Blackfin BF6xx SPORTs in I2S mode, Marvell MMP,
Synopsis Designware I2S controllers, and SPEAr DMA and S/PDIF
- New CODEC drivers for Dialog DA732x, ST STA529, ST-Ericsson AB8500, TI
Isabelle and Wolfson Microelectronics WM5102 and WM5110
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JHE2
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for 3.6
This has been a pretty quiet release - very little activity in framework
terms, mostly just a few new drivers and updates:
- Added the ability to add and remove DAPM paths dynamically, mostly for
reparenting on clock changes.
- New machine drivers for Marvell Brownstone, ST-Ericsson Ux500
reference platform and ttc-dkp.
- New CPU drivers for Blackfin BF6xx SPORTs in I2S mode, Marvell MMP,
Synopsis Designware I2S controllers, and SPEAr DMA and S/PDIF
- New CODEC drivers for Dialog DA732x, ST STA529, ST-Ericsson AB8500, TI
Isabelle and Wolfson Microelectronics WM5102 and WM5110
This patch adds input selection of main codec clock - from what pin.
Both registers set same value since codec uses clock divider or pll at one time.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds AGC target level and times settings for TLV320AIC3x.
Enums uses small arrays of two channels left and right since it uses different registers.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds missing deemphasis switch.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Adds missing register default values to cache.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In sound/soc/codecs/tlv320aic3x.c
data = snd_soc_read(codec, AIC3X_PLL_PROGA_REG);
snd_soc_write(codec, AIC3X_PLL_PROGA_REG,
data | (pll_p << PLLP_SHIFT));
In the above code, pll-p value is OR'ed with previous value without
clearing it. Bug is not seen if pll-p value doesn't change across
Sampling frequency.
However on some platforms (like AM335x EVM-SK), pll-p may have different
values across different sampling frequencies. In such case, above code
configures the pll with a wrong value.
Because of this bug, when a audio stream is played with pll value
different from previous stream, audio is heard as differently(like its
stretched).
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
ALSA mixers cannot classify this "Class-D Amplifier Gain" speaker output
gain control as a playback control. Fix this by changing the name as
"Class-D Playback Volume".
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
aic3x_set_headset_detection() isn't made available outside the driver or
referenced within the driver which sparse notices and complains about.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to support CODEC<->CODEC links remove the assumption that there
is only a single CODEC on a DAI link by removing the use of the CODEC
pointer in the rtd from the CODEC drivers. They are already being passed
their DAI whenever they are passed an rtd and can get the CODEC from
there.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we're not implementing GPIO or microphone detection support
there's no users for the read() function any more.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Looks like nobody is or will be using this code.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.
This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-
snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()
This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().
It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().
Finally, it updates the existing machine drivers that register controls to either :-
1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.
In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 33c5f969 "ASoC: Allow idle_bias_off to be specified in CODEC
drivers", now we can set idle_bias_off flag in struct snd_soc_codec_driver
for devices can unconditionally support idle_bias_off.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The existence of this parameter is purely historical. None of the CODEC drivers
uses it and we always pass in the same value anyway, so it should be safe to
remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.
The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The driver only supports I2C so doesn't need to do things conditionally.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
According to the datasheet:
Page0 / Register8: Audio Serial Data interface Control Register A
BIT 7: Bit Clock Directional Control
0: Bit clock is an input (slave mode)
1: Bit clock is an output (master mode)
BIT 6: Word Clock Directional Control
0: Word clock is an input (slave mode)
1: Word clock is an output (master mode)
Current code sets BIT_CLK_MASTER and WORD_CLK_MASTER bits for master mode,
but does not clear these bits for slave mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
codec->hw_read is broken now, let's covert to snd_soc_read.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We really should be doing this in the core, not in a driver...
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Save model information in driver_data so we can simplify the implementation.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>