On SCIx variants different from HSCIF, the bit rate is equal to the
sampling clock rate divided by half the sampling rate. Currently this is
handled by dividing the sampling rate by two, which was OK as it was
always even.
Replace halving the sampling rate by premultiplying the base clock
frequency by 2, to accommodate odd sampling rates on SCIFA/SCIFB later.
Replace the shift value in the BRG divider calculation by a
premultiplication of the base clock frequency too, for consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SCIFA and SCIFB have additional bit rate config bits in the Serial Mode
Register. Don't touch them when using the port as a serial console, as
we rely on the boot loader to have configured the serial port config.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a non console i.MX UART is enabled in the device tree,
system suspend fails due to an unprepared clock:
[ 638.794563] PM: Syncing filesystems ... done.
[ 638.878902] Freezing user space processes ... (elapsed 0.002 seconds) done.
[ 638.888454] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 638.996697] PM: suspend of devices complete after 97.200 msecs
[ 639.002611] PM: suspend devices took 0.100 seconds
[ 639.013020] PM: late suspend of devices complete after 2.288 msecs
[ 639.021486] ------------[ cut here ]------------
[ 639.026147] WARNING: CPU: 0 PID: 488 at drivers/clk/clk.c:732 clk_core_enable+0xc0/0x12c()
[ 639.034413] Modules linked in:
[ 639.037490] CPU: 0 PID: 488 Comm: system_server Tainted: G W 4.4.0-rc5-pknbsp-svn2214-atag-v4.4-rc5-121-gebfd9cb #1304
[ 639.049312] Hardware name: Freescale i.MX53 (Device Tree Support)
[ 639.055444] [<c0016d54>] (unwind_backtrace) from [<c00140f8>] (show_stack+0x20/0x24)
[ 639.063199] [<c00140f8>] (show_stack) from [<c02c99a0>] (dump_stack+0x20/0x28)
[ 639.070442] [<c02c99a0>] (dump_stack) from [<c0024ca8>] (warn_slowpath_common+0x88/0xc0)
[ 639.078541] [<c0024ca8>] (warn_slowpath_common) from [<c0024d0c>] (warn_slowpath_null+0x2c/0x34)
[ 639.087332] [<c0024d0c>] (warn_slowpath_null) from [<c05171e8>] (clk_core_enable+0xc0/0x12c)
[ 639.095777] [<c05171e8>] (clk_core_enable) from [<c05172f8>] (clk_enable+0x2c/0x40)
[ 639.103441] [<c05172f8>] (clk_enable) from [<c0349880>] (imx_serial_port_suspend_noirq+0x20/0xe0)
[ 639.112336] [<c0349880>] (imx_serial_port_suspend_noirq) from [<c03a26a0>] (dpm_run_callback+0x68/0x16c)
[ 639.121825] [<c03a26a0>] (dpm_run_callback) from [<c03a2898>] (__device_suspend_noirq+0xf4/0x22c)
[ 639.130705] [<c03a2898>] (__device_suspend_noirq) from [<c03a4b0c>] (dpm_suspend_noirq+0x148/0x30c)
[ 639.139764] [<c03a4b0c>] (dpm_suspend_noirq) from [<c00511d4>] (suspend_devices_and_enter+0x2e8/0x6a4)
[ 639.149078] [<c00511d4>] (suspend_devices_and_enter) from [<c00518a0>] (pm_suspend+0x310/0x4b8)
[ 639.157782] [<c00518a0>] (pm_suspend) from [<c00500ec>] (state_store+0x7c/0xcc)
[ 639.165099] [<c00500ec>] (state_store) from [<c02cb6dc>] (kobj_attr_store+0x1c/0x28)
[ 639.172858] [<c02cb6dc>] (kobj_attr_store) from [<c01633d4>] (sysfs_kf_write+0x54/0x58)
[ 639.180871] [<c01633d4>] (sysfs_kf_write) from [<c01629b4>] (kernfs_fop_write+0x100/0x1c8)
[ 639.189152] [<c01629b4>] (kernfs_fop_write) from [<c00fb8b8>] (__vfs_write+0x3c/0xe8)
[ 639.196991] [<c00fb8b8>] (__vfs_write) from [<c00fc810>] (vfs_write+0xa4/0x160)
[ 639.204307] [<c00fc810>] (vfs_write) from [<c00fcac4>] (SyS_write+0x4c/0x98)
[ 639.211363] [<c00fcac4>] (SyS_write) from [<c0010760>] (ret_fast_syscall+0x0/0x3c)
This does not happen for the common case of a single UART used as a console
(since imx_console_setup() already does a prepare)
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
start_tx and the ISR used largely identical code to transmit data.
Consolidate that in one place.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the _OFFSET suffix from all register defines which makes code a
little easier to read and avoids a few line breaks.
Suggested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling magic sysrq included dropping a lock to avoid a deadlock that
happened when cdns_uart_console_write tried to acquire a lock in the
from the sysrq code path. By making the acquisition of the lock in
cdns_uart_console_write depending on port->sysrq, cdns_uart_handle_rx can be
simplified to simply call uart_handle_sysrq.
Suggested-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert an if-else into the more common early return on error, reducing
the indent level of the happy path.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system could deadlock handling RX IRQs when RX-related IRQ
conditions became true while the receiver was disabled. To avoid this,
enable/disable the RX/TX IRQs together with the receiver/transmitter.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request_irq() should be _after_ h/w programming, otherwise an
interrupt could be triggered and in-progress before the h/w has been
setup.
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move RX-related IRQ handling into a helper function.
Fixes a problem where every char received after a parity or frame error
in the current isr will also be tagged as a parity or frame error.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shutting down the UART port can happen while console operations are in
progress. Holding the port lock serializes these operations and avoids
the UART HW to be disabled in the middle of console prints.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The RX path in the interrupt handler released a lock unnecessarily.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The startup function is supposed to initialize the UART for receiving.
Hence, don't enable the TX part. Also, protect HW accesses with the port
lock.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When shutting down the UART, clear the interrupt status register. Bits
in the ISR are cleared by writing them as '1'.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Restarting the transmitter even if the circ buffer is empty may be
necessary to push out remaining data when the port is restarted after
being stopped.
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of disabling the IRQ, use the spin lock to serialize accesses to
the HW. This protects the driver from interference of non-IRQ callbacks
with each other and makes the driver more consistent in its
serialization method.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"earlyprintk" is architecture specific option.
General "earlycon" option support is much better.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
[uli: preserve other SCSCR bits when asserting RE and TE]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[geert: rewording, #ifdef rework]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Considering that pci_pericom_setup(()'s only difference to
pci_default_setup() is the setting of the uartclk field, and taking
into account that this field already gets taken care of by having the
base_baud field filled in the pci_boards[] entries, there's no need
for both the function and the quirks table entry.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use to_pci_dev() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pl011 driver has gone back and forth on the definition of the
ZTE specific variation of the hardware definitions, but the
current state is that the vendor definition is left in place
yet unused:
drivers/tty/serial/amba-pl011.c:190:27: warning: 'vendor_zte' defined but not used [-Wunused-variable]
I don't know what the plan forward is to get this code to work,
but the current behavior is a bit annoying as we get a warning
whenever we build this driver.
This patch does not help us to make it work, but at least
shuts up the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 7ec7587189 ("tty: amba-pl011: add support for ZTE UART (EXPERIMENTAL)")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Busy loops that poll on a register should call cpu_relax(). On some
architectures, it can lower CPU power consumption or yield to a
hyperthreaded twin processor. It also serves as a compiler barrier,
so it can replace barrier() calls.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In datasheet, Modem Status Register MSR[4-7] reflect the modem pins
CTS/DSR/RI/CD signal state.
Signed-off-by: Wills Wang <wills.wang@live.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In all functions other than atmel_serial_probe_fifos,
atmel_serial_probe, and atmel_console_init, the name "port" is used to
refer to an instance of struct uart_port. In many of these functions,
"atmel_port" is used to refer to an instance of struct atmel_uart_port.
We make the use of the name "port" consistent by making
atmel_serial_probe_fifos, atmel_serial_probe, and atmel_console_init
use "atmel_port" to refer to an instance of struct atmel_uart_port
instead of the previous name of "port".
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Acked-by: Karthik Manamcheri <karthik.manamcheri@ni.com>
[nicolas.ferre@atmel.com: fix typo in variable, adapt to newer kernel]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting with sama5d2, the new UART revision has an hardware timer. So, add it
to the IP detection code and set the "has_hw_timer" property for it.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reported-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No functional change is associated with this patch.
A driver property depends on the Atmel serial IP revision. This property
is the way the rx timeout is handled: by an hardware or software timer.
So, change this property name and setup code so that it's easier to understand
and more future proof as the distinction of USART vs. UART is blurrier on newer
SoCs.
Variable names and debug comments are also adapted to make this code more obvious.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some UART HW has a single register combining UART_DLL/UART_DLM
(this was probably forgotten in the change that introduced the
callbacks, commit b32b19b8ff)
Fixes: b32b19b8ff ("[SERIAL] 8250: set divisor register correctly ...")
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's old, messy and mostly unmaintained.
Remove it as suggested by Peter Hurley and Alan.
Signed-off-by: Frederik Völkel <frederik.voelkel@fau.de>
Signed-off-by: Lukas Braun <lukas.braun@fau.de>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Constifies psc_ops structures in tty's serial
port driver since they are not modified after
their initialization.
Detected and found using Coccinelle.
Suggested-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Direct call to readl()/writel() is checked against iotype
and in case of UPIO_MEM32BE we use ioread32be()/iowrite32be()
instead of them.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for UPIO_MEM32BE in addition to UPIO_MEM32.
For big endian we use 2 new accessors similar to little endian,
called dw8250_serial_out32be() and dw8250_serial_in32be().
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the help of Heikki we take common code that
makes sure LCR write wasn't ignored and put it in new function called
dw8250_check_lcr(). This function serves 3 serial_out routines:
dw8250_serial_out(), dw8250_serial_out32(), and dw8250_serial_outq().
This patch only brings better code reuse.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use software emulated RS485 direction control to provide RS485 API
existed in omap_serial driver. Note that 8250_omap issues interrupt
on shift register empty which is single prerequesite for using software
emulated RS485.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implementation of software emulation of RS485 direction handling is based
on omap_serial driver.
Before and after transmission RTS is set to the appropriate value.
Note that before calling serial8250_em485_init() the caller has to
ensure that UART will interrupt when shift register empty. Otherwise,
emultaion cannot be used.
Both serial8250_em485_init() and serial8250_em485_destroy() are
idempotent functions.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Software RS485 emultaion is to be added in the following commit.
serial8250_start_tx() will need to refer serial8250_stop_rx().
Move serial8250_stop_rx() in front of serial8250_start_tx() in order
to avoid function forward declaration.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct uart_sio_port has a lots of unused members. Some of them are
set to some constant but never read. Remove all those.
This includes removal of uart_ops->pm handler as we never handle pm
(pm was never set).
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DEBUG_AUTOCONF is unused.
Switch DEBUG_INTR to pr_debug. This is only enabled with DEBUG or
dynamic debug when explicitly asked for.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only variables in old_serial_port are port and irq. So make
old_serial_port contain only those two and move the initialization of
the rest to the place where old_serial_port is actually read.
Also get rid of SERIAL_PORT_DFNS. It is ugly and having the
initializer where it belongs makes more sense. Finally, use already
defined UART_NR in the loop.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only needed information from the header is struct old_serial_port.
Move it to m32r_sio.c, make it const and anonymous. And kill the rest
from the header as it is dead stuff.
Given m32r_sio_suspend_port and m32r_sio_resume_port are local to
m32r_sio.c and unused, kill them from .c too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since check_name and check_resources return only 0/1, switch them to
bool/true/false.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a chain of up to 4 nested ifs in init and remove functions.
Instead, make the code linear and use goto's to handle failures.
Remove unneeded cast from mpsc_release_port by referencing pi->port
directly. And finally, use dev_dbg instead of pr_debug given we have
dev->dev node.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When mpsc_routing_base, sdma_intr_base, mpsc_base, sdma_base, and
brg_base are mapped, they are never unmapped. The condition in the
free paths is always 'if (!XXX_base) { unmap }'. Fix it by inverting
the condition.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DT earlycon for 8250_omap driver. This boot console is included
for kernels built with CONFIG_SERIAL_EARLYCON=y, CONFIG_OF=y,
CONFIG_SERIAL_8250_OMAP=y, and CONFIG_OF_EARLY_FLATTREE=y.
This boot console is enabled with the command line option "earlycon"
(without "=<name>...") when the DT 'stdout-path' property matches a
compatible uart. For example,
/ {
chosen {
stdout-path = "serial0:115200";
};
....
aliases {
serial0 = &uart0;
};
....
ocp : ocp {
uart0 : serial@44e09000 {
compatible = "ti,omap3-uart";
}
};
};
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
earlycon initializes struct uart_port::regshift to the correct
value for UPIO_MEM32 already. Use the port field rather than
hard-coded value.
This enables broader support for various i/o access methods in
8250 earlycon (eg., omap8250 earlycon).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Output the earlycon "driver" from the just-parsed console 'name'
and 'index' fields.
NB: ->mapbase is a resource_size_t so use %pa format specifier
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Refactor the command line earlycon banner into earlycon_init() so
both earlycon startup methods output an info banner.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleanup the early DT/earlycon separation; remove the 'addr' parameter
from of_setup_earlycon() and get the uart phys addr directly with a
new wrapper function, of_flat_dt_translate_addr(). Limit
fdt_translate_address() to file scope.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Read the optional "reg-offset", "reg-shift", "reg-io-width" and endianness
properties and initialize the respective struct uart_port field if found.
NB: These bindings are common to several drivers and the values merely
indicate the default value; the registering earlycon setup() method can
simply override the values if required.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pass-through any options string in the 'stdout-path' property to the
earlycon "driver" setup.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the console name embedded in the OF earlycon table by the
OF_EARLYCON_DECLARE() macro to initialize the struct console 'name'
and 'index' fields.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly initialize the struct console 'name' and 'index' fields for
the registering earlycon. For earlycons w/o trailing numerals, the
index is set to 0; otherwise, the index is set to the value of the
trailing numeral. For example, the 'exynos4210' earlycon name == "exynos"
and index == 4210. Earlycons with embedded numerals will have all
non-trailing numerals as part of the name; for example, the 's3c2412'
earlycon name == "s3c" and index == 2412.
This ackward scheme was initially added for the uart8250 earlycon;
adopt this scheme for the other earlycon "drivers".
Introduce earlycon_init() which performs the string scanning and
initializes the name and index fields; encapsulate the other console
field initializations within.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use a single common table of struct earlycon_id for both command line
and devicetree. Re-define OF_EARLYCON_DECLARE() macro to instance a
unique earlycon declaration (the declaration is only guaranteed to be
unique within a compilation unit; separate compilation units must still
use unique earlycon names).
The semantics of OF_EARLYCON_DECLARE() is different; it declares an
earlycon which can matched either on the command line or by devicetree.
EARLYCON_DECLARE() is semantically unchanged; it declares an earlycon
which is matched by command line only. Remove redundant instances of
EARLYCON_DECLARE().
This enables all earlycons to properly initialize struct console
with the appropriate name and index, which improves diagnostics and
enables direct earlycon-to-console handoff.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DT earlycon is only supported for CONFIG_OF_EARLY_FLATTREE=y; exclude
of_setup_earlycon() if not defined.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When the tty lock is interrupted on attempted re-open, 2 tty krefs
are still held. Drop extra kref before returning failure from
tty_lock_interruptible(), and drop lookup kref before returning
failure from tty_open().
Fixes: 0bfd464d3f ("tty: Wait interruptibly for tty lock on reopen")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small tty/serial driver fixes for 4.5-rc2.
They resolve a number of reported problems (the ioctl one specifically
has been pointed out by numerous people) and one patch adds some new
device ids for the 8250_pci driver. All have been in linux-next
successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlauWWkACgkQMUfUDdst+ykujQCfUSpPMRs3yagM24SI8ITnbEJQ
7H0An0utvQBUhgf10WA7trJ+uyzq4SsQ
=uUEE
-----END PGP SIGNATURE-----
Merge tag 'tty-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty/serial driver fixes for 4.5-rc2.
They resolve a number of reported problems (the ioctl one specifically
has been pointed out by numerous people) and one patch adds some new
device ids for the 8250_pci driver. All have been in linux-next
successfully"
* tag 'tty-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: 8250_pci: Add Intel Broadwell ports
staging/speakup: Use tty_ldisc_ref() for paste kworker
n_tty: Fix unsafe reference to "other" ldisc
tty: Fix unsafe ldisc reference via ioctl(TIOCGETD)
tty: Retry failed reopen if tty teardown in-progress
tty: Wait interruptibly for tty lock on reopen
Here are some small staging driver fixes for 4.5-rc2. One of them
predated 4.4-final, but I missed that merge window due to the holliday.
The others fix reported issues that have come up recently. The tty
change is needed for the speakup driver fix and has the ack of the tty
driver maintainer as well, i.e. myself :)
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlauWLoACgkQMUfUDdst+ynHbQCfWlGgQhtadfhtiaIKLwqy9NPG
PksAn3/z4mXX037sfm2kZrcqtcNlv9zf
=Vdai
-----END PGP SIGNATURE-----
Merge tag 'staging-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are some small staging driver fixes for 4.5-rc2.
One of them predated 4.4-final, but I missed that merge window due to
the holliday. The others fix reported issues that have come up
recently. The tty change is needed for the speakup driver fix and has
the ack of the tty driver maintainer as well, i.e. myself :)
All have been in linux-next with no reported issues"
* tag 'staging-4.5-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Staging: speakup: fix read scrolled-back VT
Staging: speakup: Fix getting port information
Revert "Staging: panel: usleep_range is preferred over udelay"
iio: adis_buffer: Fix out-of-bounds memory access
Some recent (early 2015) macbooks have Intel Broadwell where LPSS UARTs are
PCI enumerated instead of ACPI. The LPSS UART block is pretty much same as
used on Intel Baytrail so we can reuse the existing Baytrail setup code.
Add both Broadwell LPSS UART ports to the list of supported devices.
Signed-off-by: Leif Liddy <leif.liddy@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, speakup would always read the non-scrolled part of the VT,
even when the VT is scrolled back with shift-page. This patch makes
vt.c export screen_pos so that speakup can use it to properly access
the content of the scrolled-back VT.
This was tested with both vgacon and fbcon.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty core no longer provides nor uses ASYNC_CLOSING; remove from
tty_port_close_start() and tty_port_close_end() as well as tty drivers
which open-code these state changes. Unfortunately, even though the
bit is masked from userspace, its inclusion in a uapi header precludes
removing the macro.
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-s390@vger.kernel.org
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: linux-cris-kernel@axis.com
Cc: Samuel Ortiz <samuel@sortiz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty core no longer provides ASYNC_CLOSING. Use private flag for
same purpose, which is to clear the fifos at each and every interrupt
during driver close(). The driver uses this sledgehammer approach because
its close/shutdown sequence is hopelessly borked.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When throttling, time is of the essence; try RTS signalling before
soft flow control, which will take longer.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
void * promotes to any pointer type; remove type cast.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If aborting uart_open() unsuccessfully, retval is non-zero, so the
existing fall-through exit is equivalent.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The UPF_* flags are the correct values to use for struct uart_port
and struct old_serial_port/SERIAL_PORT_DFNS.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uart port may have already been removed by uart_remove_one_port();
use equivalent tty->index (which is always valid in these contexts)
instead.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
do_uart_get_info() has a single caller: uart_get_info().
Manually inline do_uart_get_info().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Expressions of the form "tty->termios.c_*flag & FLAG"
are more clearly expressed with the termios flags macros,
I_FLAG(), C_FLAG(), O_FLAG(), and L_FLAG().
Convert treewide.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of two distinct code branches for receive_buf() handling,
use tty_ldisc_receive_buf() as the single code path.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On final port close (and thus final tty close), only output flow
control requests in the input data should be processed. Ignore all
other input data, including parity errors, overruns and breaks.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver's private completion variable, close_wait, is no longer
used for wait since "tty: Remove ASYNC_CLOSING checks in open()/hangup";
remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After masking all interrupts, wait for the irq handler to complete
before continuing shutdown.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If console setup fails (eg., there is no valid port at that index),
unlink the console ptr; otherwise, when the driver unloads, the
console will be unregistered (even though setup, and thus registration,
failed) and a console disabled message will be printed.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The defunct low_latency input steering executed flush_to_ldisc()
directly from interrupt context so dropping the port lock was
necessary to avoid deadlock. That steering was removed by
commit a9c3f68f3c
Author: Peter Hurley <peter@hurleysoftware.com>
Date: Sat Feb 22 07:31:21 2014 -0500
tty: Fix low_latency BUG
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When max_count is reached, the rx loop exits. However, UART_LSR has
already been read so those char flags are lost, and subsequent rx
status will be for the wrong byte until the rx fifo drains.
Reported-by: George Spelvin <linux@horizon.com>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Factor the read/process one char inner loop to a separate helper
function serial8250_read_char(). No functional change.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to fcntl(2), "a SIGIO signal is sent whenever input
or output becomes possible on that file descriptor", i.e.
after the output buffer was full and now has space for new data.
But in fact SIGIO is sent after every write.
n_tty_write() should set TTY_DO_WRITE_WAKEUP only when
not all data could be written to the buffer.
[pjh: Also fixes missed SIGIO if amt written just happens to be
[ amount still to write
Signed-off-by: Johannes Stezenbach <js@sig21.net>
[pjh: minor patch edits and re-submit]
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since n_tty_check_unthrottle() is only called from n_tty_read()
which only originates from a userspace read(), the tty count cannot
be 0; the read() guarantees the file descriptor has not yet been
released.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If signal-driven i/o is disabled while write wakeup is pending (ie.,
n_tty_write() has set TTY_DO_WRITE_WAKEUP but then signal-driven i/o
is disabled), the TTY_DO_WRITE_WAKEUP bit will never be cleared and
will cause tty_wakeup() to always call n_tty_write_wakeup.
Unconditionally clear the write wakeup, and since kill_fasync()
already checks if the fasync ptr is null, call kill_fasync()
unconditionally as well.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A small race window exists which allows signal-driven async i/o to be
enabled for the tty when the file ptr has already been hungup and
signal-driven i/o has been disabled:
CPU 0 CPU 1
----- ------
ioctl_fioasync(on)
filp->f_op->fasync(on) __tty_hangup()
tty_fasync(on) tty_lock()
tty_lock() ...
. filp->f_op = &hung_up_tty_fops;
(waiting) __tty_fasync(off)
. tty_unlock()
/* gets tty lock */
/* enables FASYNC */
Check the tty has not been hungup while holding tty_lock.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
VFS uses a two-stage check-and-call method for invoking file_operations
methods, without explicitly snapshotting either the file_operations ptr
or the function ptr. Since the tty core is one of the few VFS users that
changes the f_op file_operations ptr of the file descriptor (when the
tty has been hung up), and since the likelihood of the compiler generating
a reload of either f_op or the function ptr is basically nil, just define
a hung up fasync() file operation that returns an error.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only the N_TTY line discipline implements the signal-driven i/o
notification enabled/disabled by fcntl(F_SETFL, O_ASYNC). The ldisc
fasync() notification is sent to the ldisc when the enable state has
changed (the tty core is notified via the fasync() VFS file operation).
The N_TTY line discipline used the enable state to change the wakeup
condition (minimum_to_wake = 1) for notifying the signal handler i/o is
available. However, just the presence of data is sufficient and necessary
to signal i/o is available, so changing minimum_to_wake is unnecessary
(and creates a race condition with read() and poll() which may be
concurrently updating minimum_to_wake).
Furthermore, since the kill_fasync() VFS helper performs no action if
the fasync list is empty, calling unconditionally is preferred; if
signal driven i/o just has been disabled, no signal will be sent by
kill_fasync() anyway so notification of the change via the ldisc
fasync() method is superfluous.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A read() in non-canonical mode when VMIN > 0 and VTIME == 0 does not
complete until at least VMIN chars have been read (or the user buffer is
full). In this infrequent read mode, n_tty_read() attempts to reduce
wakeups by computing the amount of data still necessary to complete the
read (minimum_to_wake) and only waking the read()/poll() when that much
unread data has been processed. This is the only read mode for which
new data does not necessarily generate a wakeup.
However, this optimization is broken and commonly leads to hung reads
even though the necessary amount of data has been received. Since the
optimization is of marginal value anyway, just remove the whole
thing. This also remedies a race between a concurrent poll() and
read() in this mode, where the poll() can reset the minimum_to_wake
of the read() (and vice versa).
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Warn if tty_audit_buf use is attempted after tty_audit_exit() has
already freed it.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The data read from another tty may be relevant to the action of
the TIOCSTI ioctl; log the audit buffer immediately.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Audit is unlikely to be enabled; check first to exit asap.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first-use tty audit buffer allocation is a potential race
amongst multiple attempts at 'first-use'; only one 'winner' is
acceptable.
The successful buffer assignment occurs if tty_audit_buf == NULL
(which will also be the return from cmpxchg()); otherwise, another
racer 'won' and this buffer allocation is freed.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When tty_audit_exit() is called from do_exit(), the process is
single-threaded. Since the tty_audit_buf is only shared by threads
of a process, no other thread can be concurrently accessing the
tty_audit_buf during or after tty_audit_exit().
Thus, no other thread can be holding an extra tty_audit_buf reference
which would prevent tty_audit_exit() from freeing the tty_audit_buf.
As that is the only purpose of the ref counting, remove the reference
counting and free the tty_audit_buf directly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty audit buffer is allocated at first use and not freed until
the process exits. If tty audit is turned off after the audit buffer
has been allocated, no effort is made to release the buffer.
So re-checking if tty audit has just been turned off when tty audit
was just on is false optimization; the likelihood of triggering this
condition is exceedingly small.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The audit_tty and audit_tty_log_passwd fields are actually bool
values, so merge into single memory location to access atomically.
NB: audit log operations may still occur after tty audit is disabled
which is consistent with the existing functionality
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_t instead of separate major/minor fields to track tty
audit buffer association.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_audit_push() and tty_audit_push_current() perform identical
tasks; eliminate the tty_audit_push() implementation and the
tty_audit_push_current() name.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In canonical read mode, each line read and logged is pushed separately
with tty_audit_push(). For all single-threaded processes and multi-threaded
processes reading from only one tty, this patch has no effect; the last line
read will still be the entry pushed to the audit log because the tty
association cannot have changed between tty_audit_add_data() and
tty_audit_push().
For multi-threaded processes reading from different ttys concurrently,
the audit log will have mixed log entries anyway. Consider two ttys
audited concurrently:
CPU0 CPU1
---------- ------------
tty_audit_add_data(ttyA)
tty_audit_add_data(ttyB)
tty_audit_push()
tty_audit_add_data(ttyB)
tty_audit_push()
This patch will now cause the ttyB output to be split into separate
audit log entries.
However, this possibility is equally likely without this patch:
CPU0 CPU1
---------- ------------
tty_audit_add_data(ttyB)
tty_audit_add_data(ttyA)
tty_audit_push()
tty_audit_add_data(ttyB)
tty_audit_push()
Mixed canonical and non-canonical reads have similar races.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
lock_task_sighand() is for situations where the struct task_struct*
may disappear while trying to deref the sighand; this never applies
to 'current'.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty audit buffer used to audit/record tty input is allocated on
the process's first call to tty_audit_add_data(), and not freed until
the process exits. On each call to tty_audit_add_data(), the current
tty is compared (by major:minor) with the last tty associated with
the audit buffer, and if the tty has changed the existing data is
logged to the audit log. The audit buffer is then re-associated with
the new tty.
Currently, the audit buffer is immediately associated with the tty;
however, the association must be re-checked when the buffer is locked
prior to copying the tty input. This extra step is always necessary,
since a concurrent read of a different tty by another thread of the
process may have used the buffer in between allocation and buffer
lock.
Rather than associate the audit buffer with the tty at allocation,
leave the buffer initially un-associated (null dev_t); simply let the
re-association check also perform the initial association.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty termios bits cannot change while n_tty_read() is in the
i/o loop; the termios_rwsem ensures mutual exclusion with termios
changes in n_tty_set_termios(). Check L_ICANON() directly and
eliminate icanon parameter.
NB: tty_audit_add_data() => tty_audit_buf_get() => tty_audit_buf_alloc()
is a single path; ie., tty_audit_buf_get() and tty_audit_buf_alloc()
have no other callers.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty audit never logs pty master reads, but packet mode only works for
pty masters, so tty_audit_add_data() was never logging packet mode
anyway.
Don't audit packet mode data. As those are the lone call sites, remove
tty_put_user().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reads from pty masters are not logged; early-out before taking
locks.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Access to tty->tty_files list is always per-tty, never for all ttys
simultaneously. Replace global tty_files_lock spinlock with per-tty
->files_lock. Initialize when the ->tty_files list is inited, in
alloc_tty_struct().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move is_ignored() to drivers/tty/tty_io.c and re-declare in file
scope.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reduce global tty symbols; move and rename tty_ldisc_begin() as
n_tty_init() and redefine the N_TTY ldisc ops as file scope.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_mutex is a core, system-wide lock; there is no reason for any
code outside the tty core to have direct access.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_ldisc_setup() is race-free and can reference tty->ldisc without
snapshots.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The line discipline id is stored in the tty's termios; document the
implicit initial value of N_TTY.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, when the tty is hungup, the ldisc is re-instanced; ie., the
current instance is destroyed and a new instance is created. The purpose
of this design was to guarantee a valid, open ldisc for the lifetime of
the tty.
However, now that tty buffers are owned by and have lifetime equivalent
to the tty_port (since v3.10), any data received immediately after the
ldisc is re-instanced may cause continued driver i/o operations
concurrently with the driver's hangup() operation. For drivers that
shutdown h/w on hangup, this is unexpected and usually bad. For example,
the serial core may free the xmit buffer page concurrently with an
in-progress write() operation (triggered by echo).
With the existing stable and robust ldisc reference handling, the
cleaned-up tty_reopen(), the straggling unsafe ldisc use cleaned up, and
the preparation to properly handle a NULL tty->ldisc, the ldisc instance
can be destroyed and only re-instanced when the tty is re-opened.
If the tty was opened as /dev/console or /dev/tty0, the original behavior
of re-instancing the ldisc is retained (the 'reinit' parameter to
tty_ldisc_hangup() is true). This is required since those file descriptors
are never hungup.
This patch has neglible impact on userspace; the tty file_operations ptr
is changed to point to the hungup file operations _before_ the ldisc
instance is destroyed, so only racing file operations might now retrieve
a NULL ldisc reference (which is simply handled as if the hungup file
operation had been called instead -- see "tty: Prepare for destroying
line discipline on hangup").
This resolves a long-standing FIXME and several crash reports.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At tty hangup, the line discipline instance is reinitialized by
closing the current ldisc instance and opening a new instance.
This operation is complicated by error recovery: if the attempt
to reinit the current line discipline fails, the line discipline
is reset to N_TTY (which should not but can fail).
Re-purpose tty_ldisc_reinit() to return a valid, open line discipline
instance, or otherwise, an error.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->ldisc is a ptr to struct tty_ldisc, but unfortunately 'ldisc' is
also used as a parameter or local name to refer to the line discipline
index value (ie, N_TTY, N_GSM, etc.); instead prefer the name used
by the line discipline registration/ref counting functions.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for destroying the line discipline instance on hangup,
move tty_ldisc_kill() to eliminate needless forward declarations.
No functional change.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation of destroying line discipline on hangup, fix
ldisc core operations to properly handle when the tty's ldisc is
NULL.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty file_operations (read/write/ioctl) wait for the ldisc reference
indefinitely (until ldisc lifetime events, such as hangup or TIOCSETD,
finish). Since hangup now destroys the ldisc and does not instance
another copy, file_operations must now be prepared to receive a NULL
ldisc reference from tty_ldisc_ref_wait():
CPU 0 CPU 1
----- -----
(*f_op->read)() => tty_read()
__tty_hangup()
...
f_op = &hung_up_tty_fops;
...
tty_ldisc_hangup()
tty_ldisc_lock()
tty_ldisc_kill()
tty->ldisc = NULL
tty_ldisc_unlock()
ld = tty_ldisc_ref_wait()
/* ld == NULL */
Instead, the action taken now is to return the same value as if the
tty had been hungup a moment earlier:
CPU 0 CPU 1
----- -----
__tty_hangup()
...
f_op = &hung_up_tty_fops;
(*f_op->read)() => hung_up_tty_read()
return 0;
...
tty_ldisc_hangup()
tty_ldisc_lock()
tty_ldisc_kill()
tty->ldisc = NULL
tty_ldisc_unlock()
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_ldisc_kill() sets tty->ldisc to NULL; _not_ to N_TTY with a valid
but unopened ldisc. Fix function header documentation.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_ldisc_get() returns ERR_PTR() values if unsuccessful, not NULL;
fix function header documentation.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the ldisc is released, but before the tty is destroyed, the termios
is saved (in tty_free_termios()); this termios is restored if a new
tty is created on next open(). However, the line discipline is always
reset, which is not obvious in the current method. Instead, reset
as part of the restore.
Restore the original line discipline, which may not have been N_TTY.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The chars_in_buffer() line discipline method serves no functional
purpose, other than as a (dubious) debugging aid for mostly bit-rotting
drivers. Despite being documented as an optional method, every caller
is unconditionally executed (although conditionally compiled).
Furthermore, direct tty->ldisc access without an ldisc ref is unsafe.
Lastly, N_TTY's chars_in_buffer() has warned of removal since 3.12.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the #warning indicates, the open-coded ldisc reset was always not ok.
Not only is this code long dead, but now it would have no effect as
the ldisc is destroyed when this driver's close() method returns; remove.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract the driver lookup and reopen-or-initialize logic into helper
function tty_open_by_driver(). No functional change.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Evaluate the conditions which prevent this tty being the controlling
terminal in one place, just before setting the controlling terminal.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty lock/unlock code does not belong in the special lockfunc section
which is treated specially by stack backtraces.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tty core invokes the optional driver shutdown() just before
the optional driver remove() (shutdown() has access to the termios
and remove() does not). Because pty drivers must prevent the default
remove() action, the Unix98 pty drivers define a dummy remove() function.
Instead, release the slave index in the remove() method and delete the
optional shutdown() method.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_driver_remove_tty() is only local-scope; declare as static.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty_init_termios() never returns an error; re-declare as void. Remove
unnecessary error handling from callers. Remove extern declarations
of tty_free_termios() and free_tty_struct() and re-declare in file
scope.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
free_tty_struct() is never called with NULL tty; the two call sites
would already have faulted on earlier access.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
release_tty() leaks the ldisc instance when called directly (rather
than when releasing the file descriptor from tty_release()).
Since tty_ldisc_release() clears tty->ldisc, releasing the ldisc
instance at tty teardown if tty->ldisc is non-null is not in danger
of double-releasing the ldisc.
Remove deinitialize_tty_struct() now that free_tty_struct() always
performs the tty_ldisc_deinit().
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although n_tty_check_unthrottle() has a valid ldisc reference (since
the tty core gets the ldisc ref in tty_read() before calling the line
discipline read() method), it does not have a valid ldisc reference to
the "other" pty of a pty pair. Since getting an ldisc reference for
tty->link essentially open-codes tty_wakeup(), just replace with the
equivalent tty_wakeup().
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioctl(TIOCGETD) retrieves the line discipline id directly from the
ldisc because the line discipline id (c_line) in termios is untrustworthy;
userspace may have set termios via ioctl(TCSETS*) without actually
changing the line discipline via ioctl(TIOCSETD).
However, directly accessing the current ldisc via tty->ldisc is
unsafe; the ldisc ptr dereferenced may be stale if the line discipline
is changing via ioctl(TIOCSETD) or hangup.
Wait for the line discipline reference (just like read() or write())
to retrieve the "current" line discipline id.
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A small window exists where a tty reopen will observe the tty
just prior to imminent teardown (tty->count == 0); in this case, open()
returns EIO to userspace.
Instead, retry the open after checking for signals and yielding;
this interruptible retry loop allows teardown to commence and initialize
a new tty on retry. Never retry the BSD master pty reopen; there is no
guarantee the pty pair teardown is imminent since the slave file
descriptors may remain open indefinitely.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 4.4
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow a signal to interrupt the wait for a tty reopen; eg., if
the tty has starting final close and is waiting for the device to
drain.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 4.4
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver updates for ARM SoCs. Some for SoC-family code under drivers/soc,
but also some other driver updates that don't belong anywhere else. We also
bring in the drivers/reset code through arm-soc.
Some of the larger updates:
- Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate with other
parts of the chip/board on these platforms, all proprietary protocols that
don't fit into other subsystems and live in drivers/soc for now.
- System bus driver for UniPhier
- Driver for the TI Wakeup M3 IPC device
- Power management for Raspberry PI
+ Again a bunch of other smaller updates and patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=khZ5
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs. Some for SoC-family code under
drivers/soc, but also some other driver updates that don't belong
anywhere else. We also bring in the drivers/reset code through
arm-soc.
Some of the larger updates:
- Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate
with other parts of the chip/board on these platforms, all
proprietary protocols that don't fit into other subsystems and live
in drivers/soc for now.
- System bus driver for UniPhier
- Driver for the TI Wakeup M3 IPC device
- Power management for Raspberry PI
+ Again a bunch of other smaller updates and patches"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
bus: uniphier: allow only built-in driver
ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency
MAINTAINERS: Drop Kumar Gala from QCOM
bus: uniphier-system-bus: add UniPhier System Bus driver
ARM: bcm2835: add rpi power domain driver
dt-bindings: add rpi power domain driver bindings
ARM: bcm2835: Define two new packets from the latest firmware.
drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular
soc: mediatek: SCPSYS: Add regulator support
MAINTAINERS: Change QCOM entries
soc: qcom: smd-rpm: Add existing platform support
memory/tegra: Add number of TLB lines for Tegra124
reset: hi6220: fix modular build
soc: qcom: Introduce WCNSS_CTRL SMD client
ARM: qcom: select ARM_CPU_SUSPEND for power management
MAINTAINERS: Add rules for Qualcomm dts files
soc: qcom: enable smsm/smp2p modular build
serial: msm_serial: Make config tristate
soc: qcom: smp2p: Qualcomm Shared Memory Point to Point
soc: qcom: smsm: Add driver for Qualcomm SMSM
...
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWmsZhAAoJEEEQszewGV1ztq0QAJ1KbNOpmf/s3INkOH4r771Z
WIrNEsmwwLIAryo8gKNOM0H1zCwhRUV7hIE5jYWgD6JvjuAN6vobMlZAq21j6YpB
pKgqnI5DuoND450xjb8wSwGQ5NTYp1rFXNmwCrtyTjOle6AAW+Kp2cvVWxVr77Av
uJinRuuBr9GOKW/yYM1Fw/6EPjkvvhVOb+LBguRyVvq0s5Peyw7ZVeY1tjgPHJLn
oSZ9dmPUjHEn91oZQbtfro3plOObcxdgJ8vo//pgEmyhMeR8XjXES+aUfErxqWOU
PimrZuMMy4cxnsqWwh3Dyxo7KSWfJKfSPRwnGwc/HgbHZEoWxOZI1ezRtGKrRQtj
vubxp5dUBA5z66TMsOCeJtzKVSofkvgX2Wr/Y9jKp5oy9cHdAZv9+jEHV1pr6asz
Tas97MmmO77XuRI/GPDqVHx8dfa15OIz9s92+Gu64KxNzVxTo4+NdoPSNxkbCILO
FKn7EmU3D0OjmN2NJ9GAURoFaj3BBUgNhaxacG9j2bieyh+euuUHRtyh2k8zXR9y
8OnY1UOrTUYF8YIq9pXZxMQRD/lqwCNHvEjtI6BqMcNx4MptfTL+FKYUkn/SgCYk
QTNV6Ui+ety5D5aEpp5q0ItGsrDJ2LYSItsS+cOtMy2ieOxbQav9NWwu7eI3l5ly
gwYTZjG9p9joPXLW0E3g
=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta,
Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
- cxl: Fix possible idr warning when contexts are released from Vaibhav Jain
- cxl: use correct operator when writing pcie config space values from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan
- Freescale updates from Scott: Highlights include moving QE code out of
arch/powerpc (to be shared with arm), device tree updates, and minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5bX
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Core:
- Ground work for the new Power9 MMU from Aneesh Kumar K.V
- Optimise FP/VMX/VSX context switching from Anton Blanchard
Misc:
- Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica
Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling,
Andrew Donnellan
- Allow wrapper to work on non-english system from Laurent Vivier
- Add rN aliases to the pt_regs_offset table from Rashmica Gupta
- Fix module autoload for rackmeter & axonram drivers from Luis de
Bethencourt
- Include KVM guest test in all interrupt vectors from Paul Mackerras
- Fix DSCR inheritance over fork() from Anton Blanchard
- Make value-returning atomics & {cmp}xchg* & their atomic_ versions
fully ordered from Boqun Feng
- Print MSR TM bits in oops messages from Michael Neuling
- Add TM signal return & invalid stack selftests from Michael Neuling
- Limit EPOW reset event warnings from Vipin K Parashar
- Remove the Cell QPACE code from Rashmica Gupta
- Append linux_banner to exception information in xmon from Rashmica
Gupta
- Add selftest to check if VSRs are corrupted from Rashmica Gupta
- Remove broken GregorianDay() from Daniel Axtens
- Import Anton's context_switch2 benchmark into selftests from
Michael Ellerman
- Add selftest script to test HMI functionality from Daniel Axtens
- Remove obsolete OPAL v2 support from Stewart Smith
- Make enter_rtas() private from Michael Ellerman
- PPR exception cleanups from Michael Ellerman
- Add page soft dirty tracking from Laurent Dufour
- Add support for Nvlink NPUs from Alistair Popple
- Add support for kexec on 476fpe from Alistair Popple
- Enable kernel CPU dlpar from sysfs from Nathan Fontenot
- Copy only required pieces of the mm_context_t to the paca from
Michael Neuling
- Add a kmsg_dumper that flushes OPAL console output on panic from
Russell Currey
- Implement save_stack_trace_regs() to enable kprobe stack tracing
from Steven Rostedt
- Add HWCAP bits for Power9 from Michael Ellerman
- Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V
- Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins
- scripts/recordmcount.pl: support data in text section on powerpc
from Ulrich Weigand
- Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand
cxl:
- cxl: Fix possible idr warning when contexts are released from
Vaibhav Jain
- cxl: use correct operator when writing pcie config space values
from Andrew Donnellan
- cxl: Fix DSI misses when the context owning task exits from Vaibhav
Jain
- cxl: fix build for GCC 4.6.x from Brian Norris
- cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris
- cxl: Enable PCI device ID for future IBM CXL adapter from Uma
Krishnan
Freescale:
- Freescale updates from Scott: Highlights include moving QE code out
of arch/powerpc (to be shared with arm), device tree updates, and
minor fixes"
* tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits)
powerpc/module: Handle R_PPC64_ENTRY relocations
scripts/recordmcount.pl: support data in text section on powerpc
powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages
powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff
powerpc/mm: Fix _PAGE_PTE breaking swapoff
cxl: Enable PCI device ID for future IBM CXL adapter
cxl: use -Werror only with CONFIG_PPC_WERROR
cxl: fix build for GCC 4.6.x
powerpc: Add HWCAP bits for Power9
powerpc/powernv: Reserve PE#0 on NPU
powerpc/powernv: Change NPU PE# assignment
powerpc/powernv: Fix update of NVLink DMA mask
powerpc/powernv: Remove misleading comment in pci.c
powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing
powerpc: Fix build break due to paca mm_context_t changes
cxl: Fix DSI misses when the context owning task exits
MAINTAINERS: Update Scott Wood's e-mail address
powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery()
powerpc: Fix style of self-test config prompts
powerpc/powernv: Only delay opal_rtc_read() retry when necessary
...
Here is the big serial/tty driver updates for 4.5-rc1. Lots of driver
updates and some tty core changes. All of these have been in linux-next
and the details are in the shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlaV0iQACgkQMUfUDdst+ynukgCeNdulE6XMg5Xp3Wn3hs0ZW6fo
YmUAoMRrtjFCixhiGHoNKTm35V4gC2sy
=D64i
-----END PGP SIGNATURE-----
Merge tag 'tty-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big serial/tty driver update for 4.5-rc1.
Lots of driver updates and some tty core changes. All of these have
been in linux-next and the details are in the shortlog"
* tag 'tty-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (127 commits)
drivers/tty/serial: delete unused MODULE_DEVICE_TABLE from atmel_serial.c
serial: sh-sci: Remove cpufreq notifier to fix crash/deadlock
serial: 8250: of: Fix the driver and actually compile the 8250_of
tty: amba-pl011: use iotype instead of access_32b to track 32-bit I/O
tty: amba-pl011: fix earlycon register offsets
serial: sh-sci: Drop the sci_fck clock fallback
sh: sh7734: Correct SCIF type for BRG
sh: Remove sci_ick clock alias
sh: Rename sci_ick and sci_fck clock to fck
serial: sh-sci: Add support for optional BRG on (H)SCIF
serial: sh-sci: Add support for optional external (H)SCK input
serial: sh-sci: Prepare for multiple sampling clock sources
serial: sh-sci: Correct SCIF type on R-Car for BRG
serial: sh-sci: Correct SCIF type on RZ/A1H
serial: sh-sci: Replace struct sci_port_info by type/regtype encoding
serial: sh-sci: Add BRG register definitions
serial: sh-sci: Take into account sampling rate for max baud rate
serial: sh-sci: Merge sci_scbrr_calc() and sci_baud_calc_hscif()
serial: sh-sci: Avoid calculating the receive margin for HSCIF
serial: sh-sci: Improve bit rate error calculation for HSCIF
...
In commit c39dfebc77 ("drivers/tty/serial:
make serial/atmel_serial.c explicitly non-modular") we removed the code
relating to modular support since it currently only supports built in.
However, when redoing my build coverage for mips allmodconfig, which
sets CONFIG_OF, I noticed a remaining line that needs to be removed,
else we will get a build failure for an undefined module macro.
Unfortunately this didn't appear for any of the other arch I tested
more frequently, such as ARM.
Since MODULE_DEVICE_TABLE is a no-op for non-modular code, we can just
remove the offending line.
Fixes: c39dfebc77 ("drivers/tty/serial: make serial/atmel_serial.c explicitly non-modular")
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jiri Slaby <jslaby@suse.com>
Reported-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The BSP team noticed that there is spin/mutex lock issue on sh-sci when
CPUFREQ is used. The issue is that the notifier function may call
mutex_lock() while the spinlock is held, which can lead to a BUG().
This may happen if CPUFREQ is changed while another CPU calls
clk_get_rate().
Taking the spinlock was added to the notifier function in commit
e552de2413 ("sh-sci: add platform device private data"), to
protect the list of serial ports against modification during traversal.
At that time the Common Clock Framework didn't exist yet, and
clk_get_rate() just returned clk->rate without taking a mutex.
Note that since commit d535a2305f ("serial: sh-sci: Require a
device per port mapping."), there's no longer a list of serial ports to
traverse, and taking the spinlock became superfluous.
To fix the issue, just remove the cpufreq notifier:
1. The notifier doesn't work correctly: all it does is update stored
clock rates; it does not update the divider in the hardware.
The divider will only be updated when calling sci_set_termios().
I believe this was broken back in 2004, when the old
drivers/char/sh-sci.c driver (where the notifier did update the
divider) was replaced by drivers/serial/sh-sci.c (where the
notifier just updated port->uartclk).
Cfr. full-history-linux commits 6f8deaef2e9675d9 ("[PATCH] sh: port
sh-sci driver to the new API") and 3f73fe878dc9210a ("[PATCH]
Remove old sh-sci driver").
2. On modern SoCs, the sh-sci parent clock rate is no longer related
to the CPU clock rate anyway, so using a cpufreq notifier is
futile.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Geert writes:
Summary:
- Clean up the naming of clocks in the sh-sci driver and its DT bindings,
- Add support for the optional external clock on (H)SCI(F), where this pin
can serve as a clock input,
- Add support for the optional clock sources for the Baud Rate
Generator for External Clock (BRG), as found on some SCIF variants
and on HSCIF.
The 8250_of never compiled since in the Kconfig we have SERIAL_OF_PLATFORM
but in the makefile we expect to have SERIAL_8250_OF...
When the 8250_of.c is actually compiled we will have two errors:
missing linux/nwpserial.h and 8250/8250.h.
Fix those as well at the same time when enable the compilation of the
driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Fixes: afd7f88f15 ("serial: 8250: move of_serial code to 8250 directory")
Reported-by: Guenter Roeck <linux@roeck-us.net>
CC: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of defining a new field in the uart_amba_port structure, use the
existing iotype field of the uart_port structure, which is intended for
this purpose. If we need to use 32-bit register access, we set iotype
to UPIO_MEM32, otherwise we set it to UPIO_MEM.
For early console, specify the "mmio32" option on the kernel command-line.
Example:
earlycon=pl011,mmio32,0x3ced1000
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The REG_x macros are indices into a table, not register offsets. Since earlycon
does not have access to the vendor data, we can currently only support standard
ARM PL011 devices.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Huang Shijie <shijie.huang@arm.com>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull RCU changes from Paul E. McKenney:
- Adding transitivity uniformly to rcu_node structure ->lock
acquisitions. (This is implemented by the first two commits
on top of v4.4-rc2 due to the pervasive nature of this change.)
- Documentation updates, including RCU requirements.
- Expedited grace-period changes.
- Miscellaneous fixes.
- Linked-list fixes, courtesy of KTSAN.
- Torture-test updates.
- Late-breaking fix to sysrq-generated crash.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 984d74a720 ("sysrq: rcu-ify __handle_sysrq") replaced
spin_lock_irqsave() calls with rcu_read_lock() calls in sysrq. Since
rcu_read_lock() does not disable preemption, faulthandler_disabled() in
__do_page_fault() in x86/fault.c returns false. When the code later calls
might_sleep() in the pagefault handler, we get the following warning:
BUG: sleeping function called from invalid context at ../arch/x86/mm/fault.c:1187
in_atomic(): 0, irqs_disabled(): 0, pid: 4706, name: bash
Preemption disabled at:[<ffffffff81484339>] printk+0x48/0x4a
To fix this, we release the RCU read lock before we crash.
Tested this patch on linux 3.18 by booting off one of our boards.
Fixes: 984d74a720 ("sysrq: rcu-ify __handle_sysrq")
Signed-off-by: Ani Sinha <ani@arista.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Pull sparc fixes from David Miller:
1) Finally make perf stack backtraces stable on sparc, several problems
(mostly due to the context in which the user copies from the stack
are done) contributed to this.
From Rob Gardner.
2) Export ADI capability if the cpu supports it.
3) Hook up userfaultfd system call.
4) When faults happen during user copies we really have to clean up and
restore the FPU state fully. Also from Rob Gardner
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
tty/serial: Skip 'NULL' char after console break when sysrq enabled
sparc64: fix FP corruption in user copy functions
sparc64: Perf should save/restore fault info
sparc64: Ensure perf can access user stacks
sparc64: Don't set %pil in rtrap_nmi too early
sparc64: Add ADI capability to cpu capabilities
tty: serial: constify sunhv_ops structs
sparc: Hook up userfaultfd system call
When sysrq is triggered from console, serial driver for SUN hypervisor
console receives a console break and enables the sysrq. It expects a valid
sysrq char following with break. Meanwhile if driver receives 'NULL'
ASCII char then it disables sysrq and sysrq handler will never be invoked.
This fix skips calling uart sysrq handler when 'NULL' is received while
sysrq is enabled.
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Acked-by: Karl Volz <karl.volz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Constifies sunhv_ops structures in tty's serial
driver since they are not modified after their
initialization.
Detected and found using Coccinelle.
Suggested-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ls1 has qe and ls1 has arm cpu.
move qe from arch/powerpc to drivers/soc/fsl
to adapt to powerpc and arm
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Geert Uytterhoeven