icsk_rto is a 32bit field, and icsk_backoff can reach 15 by default,
or more if some sysctl (eg tcp_retries2) are changed.
Better use 64bit to perform icsk_rto << icsk_backoff operations
As Joe Perches suggested, add a helper for this.
Yuchung spotted the tcp_v4_err() case.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC2710 (MLDv1), section 3.7. says:
The length of a received MLD message is computed by taking the
IPv6 Payload Length value and subtracting the length of any IPv6
extension headers present between the IPv6 header and the MLD
message. If that length is greater than 24 octets, that indicates
that there are other fields present *beyond* the fields described
above, perhaps belonging to a *future backwards-compatible* version
of MLD. An implementation of the version of MLD specified in this
document *MUST NOT* send an MLD message longer than 24 octets and
MUST ignore anything past the first 24 octets of a received MLD
message.
RFC3810 (MLDv2), section 8.2.1. states for *listeners* regarding
presence of MLDv1 routers:
In order to be compatible with MLDv1 routers, MLDv2 hosts MUST
operate in version 1 compatibility mode. [...] When Host
Compatibility Mode is MLDv2, a host acts using the MLDv2 protocol
on that interface. When Host Compatibility Mode is MLDv1, a host
acts in MLDv1 compatibility mode, using *only* the MLDv1 protocol,
on that interface. [...]
While section 8.3.1. specifies *router* behaviour regarding presence
of MLDv1 routers:
MLDv2 routers may be placed on a network where there is at least
one MLDv1 router. The following requirements apply:
If an MLDv1 router is present on the link, the Querier MUST use
the *lowest* version of MLD present on the network. This must be
administratively assured. Routers that desire to be compatible
with MLDv1 MUST have a configuration option to act in MLDv1 mode;
if an MLDv1 router is present on the link, the system administrator
must explicitly configure all MLDv2 routers to act in MLDv1 mode.
When in MLDv1 mode, the Querier MUST send periodic General Queries
truncated at the Multicast Address field (i.e., 24 bytes long),
and SHOULD also warn about receiving an MLDv2 Query (such warnings
must be rate-limited). The Querier MUST also fill in the Maximum
Response Delay in the Maximum Response Code field, i.e., the
exponential algorithm described in section 5.1.3. is not used. [...]
That means that we should not get queries from different versions of
MLD. When there's a MLDv1 router present, MLDv2 enforces truncation
and MRC == MRD (both fields are overlapping within the 24 octet range).
Section 8.3.2. specifies behaviour in the presence of MLDv1 multicast
address *listeners*:
MLDv2 routers may be placed on a network where there are hosts
that have not yet been upgraded to MLDv2. In order to be compatible
with MLDv1 hosts, MLDv2 routers MUST operate in version 1 compatibility
mode. MLDv2 routers keep a compatibility mode per multicast address
record. The compatibility mode of a multicast address is determined
from the Multicast Address Compatibility Mode variable, which can be
in one of the two following states: MLDv1 or MLDv2.
The Multicast Address Compatibility Mode of a multicast address
record is set to MLDv1 whenever an MLDv1 Multicast Listener Report is
*received* for that multicast address. At the same time, the Older
Version Host Present timer for the multicast address is set to Older
Version Host Present Timeout seconds. The timer is re-set whenever a
new MLDv1 Report is received for that multicast address. If the Older
Version Host Present timer expires, the router switches back to
Multicast Address Compatibility Mode of MLDv2 for that multicast
address. [...]
That means, what can happen is the following scenario, that hosts can
act in MLDv1 compatibility mode when they previously have received an
MLDv1 query (or, simply operate in MLDv1 mode-only); and at the same
time, an MLDv2 router could start up and transmits MLDv2 startup query
messages while being unaware of the current operational mode.
Given RFC2710, section 3.7 we would need to answer to that with an MLDv1
listener report, so that the router according to RFC3810, section 8.3.2.
would receive that and internally switch to MLDv1 compatibility as well.
Right now, I believe since the initial implementation of MLDv2, Linux
hosts would just silently drop such MLDv2 queries instead of replying
with an MLDv1 listener report, which would prevent a MLDv2 router going
into fallback mode (until it receives other MLDv1 queries).
Since the mapping of MRC to MRD in exactly such cases can make use of
the exponential algorithm from 5.1.3, we cannot [strictly speaking] be
aware in MLDv1 of the encoding in MRC, it seems also not mentioned by
the RFC. Since encodings are the same up to 32767, assume in such a
situation this value as a hard upper limit we would clamp. We have asked
one of the RFC authors on that regard, and he mentioned that there seem
not to be any implementations that make use of that exponential algorithm
on startup messages. In any case, this patch fixes this MLD
interoperability issue.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow switch drivers to implement per-port Wake-on-LAN getter and
setters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an abstraction layer to suspend/resume switch devices, doing the
following split:
- suspend/resume the slave network devices and their corresponding PHY
devices
- suspend/resume the switch hardware using switch driver callbacks
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature is intended for archs having cache line larger then 64B.
Since our CQE/EQEs are generally 64B in those systems, HW will write
twice to the same cache line consecutively, causing pipe locks due to
he hazard prevention mechanism. For elements in a cyclic buffer, writes
are consecutive, so entries smaller than a cache line should be
avoided, especially if they are written at a high rate.
Reduce consecutive writes to same cache line in CQs/EQs, by allowing the
driver to increase the distance between entries so that each will reside
in a different cache line. Until the introduction of this feature, there
were two types of CQE/EQE:
1. 32B stride and context in the [0-31] segment
2. 64B stride and context in the [32-63] segment
This feature introduces two additional types:
3. 128B stride and context in the [0-31] segment (128B cache line)
4. 256B stride and context in the [0-31] segment (256B cache line)
Modify the mlx4_core driver to query the device for the CQE/EQE cache
line stride capability and to enable that capability when the host
cache line size is larger than 64 bytes (supported cache lines are
128B and 256B).
The mlx4 IB driver and libmlx4 need not be aware of this change. The PF
context behaviour is changed to require this change in VF drivers
running on such archs.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ptr used to be a non __percpu pointer (result of a this_cpu_ptr
assignment, 7d720c3e4f ("percpu: add __percpu sparse annotations to
net")). Since d25398df59 ("net: avoid reloads in SNMP_UPD_PO_STATS"),
that's no longer the case, SNMP_UPD_PO_STATS uses this_cpu_add and ptr
is now __percpu.
Silence sparse warnings by preserving the original type and
annotation, and remove the out-of-date comment.
warning: incorrect type in initializer (different address spaces)
expected unsigned long long *ptr
got unsigned long long [noderef] <asn:3>*<noident>
warning: incorrect type in initializer (different address spaces)
expected void const [noderef] <asn:3>*__vpp_verify
got unsigned long long *<noident>
warning: incorrect type in initializer (different address spaces)
expected void const [noderef] <asn:3>*__vpp_verify
got unsigned long long *<noident>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added netlink attrs to configure FOU encapsulation for GRE, netlink
handling of these flags, and properly adjust MTU for encapsulation.
ip_tunnel_encap is called from ip_tunnel_xmit to actually perform FOU
encapsulation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes IP tunnel to support (secondary) encapsulation,
Foo-over-UDP. Changes include:
1) Adding tun_hlen as the tunnel header length, encap_hlen as the
encapsulation header length, and hlen becomes the grand total
of these.
2) Added common netlink define to support FOU encapsulation.
3) Routines to perform FOU encapsulation.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement fou_gro_receive and fou_gro_complete, and populate these
in the correponsing udp_offloads for the socket. Added ipproto to
udp_offloads and pass this from UDP to the fou GRO routine in proto
field of napi_gro_cb structure.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides a receive path for foo-over-udp. This allows
direct encapsulation of IP protocols over UDP. The bound destination
port is used to map to an IP protocol, and the XFRM framework
(udp_encap_rcv) is used to receive encapsulated packets. Upon
reception, the encapsulation header is logically removed (pointer
to transport header is advanced) and the packet is reinjected into
the receive path with the IP protocol indicated by the mapping.
Netlink is used to configure FOU ports. The configuration information
includes the port number to bind to and the IP protocol corresponding
to that port.
This should support GRE/UDP
(http://tools.ietf.org/html/draft-yong-tsvwg-gre-in-udp-encap-02),
as will as the other IP tunneling protocols (IPIP, SIT).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some switch drivers (e.g: bcm_sf2) may have to communicate specific
workarounds or flags towards the PHY device driver. Allow switches
driver to be delegated that task by introducing a get_phy_flags()
callback which will do just that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have removed the need for the PHY_BRCM_100MBPS_WAR flag, we
can remove it from the GENET driver and the broadcom shared header file.
The PHY driver checks the PHY supported bitmask instead.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Broadcom BCM7xxx internal PHYs do not contain any useful revision
information in the low 4-bits of their MII_PHYSID2 (MII register 3)
which could allow us to properly identify them.
As a result, we need the actual hardware block integrating these PHYs:
GENET or the SF2 switch to tell us what revision they are built with. To
assist with that, add two helper macros for fetching the the PHY
revision and patch level from the struct phy_device::dev_flags.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract from sock_alloc_send_pskb() code building skb with frags,
so that we can reuse this in other contexts.
Intent is to use it from tcp_send_rcvq(), tcp_collapse(), ...
We also want to replace some skb_linearize() calls to a more reliable
strategy in pathological cases where we need to reduce number of frags.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added a few more UDP tunnel APIs that can be shared by UDP based
tunnel protocol implementation. The main ones are highlighted below.
setup_udp_tunnel_sock() configures UDP listener socket for
receiving UDP encapsulated packets.
udp_tunnel_xmit_skb() and upd_tunnel6_xmit_skb() transmit skb
using UDP encapsulation.
udp_tunnel_sock_release() closes the UDP tunnel listener socket.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ip6_udp_tunnel.c for ipv6 UDP tunnel functions to avoid ifdefs
in udp_tunnel.c
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recirc action allows a packet to reenter openvswitch processing.
currently openvswitch lookup flow for packet received and execute
set of actions on that packet, with help of recirc action we can
process/modify the packet and recirculate it back in openvswitch
for another pass.
OVS hash action calculates 5-tupple hash and set hash in flow-key
hash. This can be used along with recirculation for distributing
packets among different ports for bond devices.
For example:
OVS bonding can use following actions:
Match on: bond flow; Action: hash, recirc(id)
Match on: recirc-id == id and hash lower bits == a;
Action: output port_bond_a
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev. From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.
So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change addresses several issues.
First, it was possible to set tag_protocol without setting the ops pointer.
To correct that I have reordered things so that rcv is now populated before
we set tag_protocol.
Second, it didn't make much sense to keep setting the device ops each time a
new slave was registered. So by moving the receive portion out into root
switch initialization that issue should be addressed.
Third, I wanted to avoid sending tags if the rcv pointer was not registered
so I changed the tag check to verify if the rcv function pointer is set on
the root tree. If it is then we start sending DSA tagged frames.
Finally I split the device ops pointer in the structures into two spots. I
placed the rcv function pointer in the root switch since this makes it
easiest to access from there, and I placed the xmit function pointer in the
slave for the same reason.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects an error seen when DSA tagging is built as a module.
Without this change it is not possible to get XDSA tagged frames as the
test for tagging is stripped by the #ifdef check.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we have 2 pkt_type_offset functions doing the same thing and
spread across the architecture files. Remove those and replace them
with a PKT_TYPE_OFFSET macro helper which gets the constant value from a
zero sized sk_buff member right in front of the bitfield with offsetof.
This new offset marker does not change size of struct sk_buff.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Daniel Borkmann <dborkman@redhat.com>
Cc: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we introduced an additional multiplexing/demultiplexing layer
with commit 3e8a72d1da ("net: dsa: reduce number of protocol hooks")
that lives within the DSA code, we no longer need to have a given switch
driver tag_protocol be an actual ethertype value, instead, we can
replace it with an enum: dsa_tag_protocol.
Do this replacement in the drivers, which allows us to get rid of the
cpu_to_be16()/htons() dance, and remove ETH_P_BRCMTAG since we do not
need it anymore.
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it accept inet6_dev, and rename it to __ipv6_dev_ac_inc()
to reflect this change.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These code is now protected by rtnl lock, rcu read lock
is useless now.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make cls_tcindex RCU safe.
This patch addds a new RCU routine rcu_dereference_bh_rtnl() to check
caller either holds the rcu read lock or RTNL. This is needed to
handle the case where tcindex_lookup() is being called in both cases.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rcu'ify tcf_proto this allows calling tc_classify() without holding
any locks. Updaters are protected by RTNL.
This patch prepares the core net_sched infrastracture for running
the classifier/action chains without holding the qdisc lock however
it does nothing to ensure cls_xxx and act_xxx types also work without
locking. Additional patches are required to address the fall out.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu notation to qdisc handling by doing this we can make
smatch output more legible. And anyways some of the cases should
be using rcu_dereference() see qdisc_all_tx_empty(),
qdisc_tx_chainging(), and so on.
Also *wake_queue() API is commonly called from driver timer routines
without rcu lock or rtnl lock. So I added rcu_read_lock() blocks
around netif_wake_subqueue and netif_tx_wake_queue.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since BPF JIT depends on the availability of module_alloc() and
module_free() helpers (HAVE_BPF_JIT and MODULES), we better build
that code only in case we have BPF_JIT in our config enabled, just
like with other JIT code. Fixes builds for arm/marzen_defconfig
and sh/rsk7269_defconfig.
====================
kernel/built-in.o: In function `bpf_jit_binary_alloc':
/home/cwang/linux/kernel/bpf/core.c:144: undefined reference to `module_alloc'
kernel/built-in.o: In function `bpf_jit_binary_free':
/home/cwang/linux/kernel/bpf/core.c:164: undefined reference to `module_free'
make: *** [vmlinux] Error 1
====================
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: 738cbe72ad ("net: bpf: consolidate JIT binary allocator")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
nf-next pull request
The following patchset contains Netfilter/IPVS updates for your
net-next tree. Regarding nf_tables, most updates focus on consolidating
the NAT infrastructure and adding support for masquerading. More
specifically, they are:
1) use __u8 instead of u_int8_t in arptables header, from
Mike Frysinger.
2) Add support to match by skb->pkttype to the meta expression, from
Ana Rey.
3) Add support to match by cpu to the meta expression, also from
Ana Rey.
4) A smatch warning about IPSET_ATTR_MARKMASK validation, patch from
Vytas Dauksa.
5) Fix netnet and netportnet hash types the range support for IPv4,
from Sergey Popovich.
6) Fix missing-field-initializer warnings resolved, from Mark Rustad.
7) Dan Carperter reported possible integer overflows in ipset, from
Jozsef Kadlecsick.
8) Filter out accounting objects in nfacct by type, so you can
selectively reset quotas, from Alexey Perevalov.
9) Move specific NAT IPv4 functions to the core so x_tables and
nf_tables can share the same NAT IPv4 engine.
10) Use the new NAT IPv4 functions from nft_chain_nat_ipv4.
11) Move specific NAT IPv6 functions to the core so x_tables and
nf_tables can share the same NAT IPv4 engine.
12) Use the new NAT IPv6 functions from nft_chain_nat_ipv6.
13) Refactor code to add nft_delrule(), which can be reused in the
enhancement of the NFT_MSG_DELTABLE to remove a table and its
content, from Arturo Borrero.
14) Add a helper function to unregister chain hooks, from
Arturo Borrero.
15) A cleanup to rename to nft_delrule_by_chain for consistency with
the new nft_*() functions, also from Arturo.
16) Add support to match devgroup to the meta expression, from Ana Rey.
17) Reduce stack usage for IPVS socket option, from Julian Anastasov.
18) Remove unnecessary textsearch state initialization in xt_string,
from Bojan Prtvar.
19) Add several helper functions to nf_tables, more work to prepare
the enhancement of NFT_MSG_DELTABLE, again from Arturo Borrero.
20) Enhance NFT_MSG_DELTABLE to delete a table and its content, from
Arturo Borrero.
21) Support NAT flags in the nat expression to indicate the flavour,
eg. random fully, from Arturo.
22) Add missing audit code to ebtables when replacing tables, from
Nicolas Dichtel.
23) Generalize the IPv4 masquerading code to allow its re-use from
nf_tables, from Arturo.
24) Generalize the IPv6 masquerading code, also from Arturo.
25) Add the new masq expression to support IPv4/IPv6 masquerading
from nf_tables, also from Arturo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Few packets have timestamping enabled. Exit sock_tx_timestamp quickly
in this common case.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Mikulas Patocka, kmemcheck currently barks out a
false positive since we don't have special kmemcheck annotation
for bitfields used in bpf_prog structure.
We currently have jited:1, len:31 and thus when accessing len
while CONFIG_KMEMCHECK enabled, kmemcheck throws a warning that
we're reading uninitialized memory.
As we don't need the whole bit universe for pages member, we
can just split it to u16 and use a bool flag for jited instead
of a bitfield.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced in commit 314beb9bca ("x86: bpf_jit_comp: secure bpf jit
against spraying attacks") and later on replicated in aa2d2c73c2
("s390/bpf,jit: address randomize and write protect jit code") for
s390 architecture, write protection for BPF JIT images got added and
a random start address of the JIT code, so that it's not on a page
boundary anymore.
Since both use a very similar allocator for the BPF binary header,
we can consolidate this code into the BPF core as it's mostly JIT
independant anyway.
This will also allow for future archs that support DEBUG_SET_MODULE_RONX
to just reuse instead of reimplementing it.
JIT tested on x86_64 and s390x with BPF test suite.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow rtnetlink users to get bridge master info in IFLA_INFO_DATA attr
This initial part implements forward_delay, hello_time, max_age options.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
net.ipv4.ip_nonlocal_bind sysctl was global to all network
namespaces. This patch allows to set a different value for each
network namespace.
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Signed-off-by: David S. Miller <davem@davemloft.net>
allow user space to generate eBPF programs
uapi/linux/bpf.h: eBPF instruction set definition
linux/filter.h: the rest
This patch only moves macro definitions, but practically it freezes existing
eBPF instruction set, though new instructions can still be added in the future.
These eBPF definitions cannot go into uapi/linux/filter.h, since the names
may conflict with existing applications.
Full eBPF ISA description is in Documentation/networking/filter.txt
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add BPF_LD_IMM64 instruction to load 64-bit immediate value into a register.
All previous instructions were 8-byte. This is first 16-byte instruction.
Two consecutive 'struct bpf_insn' blocks are interpreted as single instruction:
insn[0].code = BPF_LD | BPF_DW | BPF_IMM
insn[0].dst_reg = destination register
insn[0].imm = lower 32-bit
insn[1].code = 0
insn[1].imm = upper 32-bit
All unused fields must be zero.
Classic BPF has similar instruction: BPF_LD | BPF_W | BPF_IMM
which loads 32-bit immediate value into a register.
x64 JITs it as single 'movabsq %rax, imm64'
arm64 may JIT as sequence of four 'movk x0, #imm16, lsl #shift' insn
Note that old eBPF programs are binary compatible with new interpreter.
It helps eBPF programs load 64-bit constant into a register with one
instruction instead of using two registers and 4 instructions:
BPF_MOV32_IMM(R1, imm32)
BPF_ALU64_IMM(BPF_LSH, R1, 32)
BPF_MOV32_IMM(R2, imm32)
BPF_ALU64_REG(BPF_OR, R1, R2)
User space generated programs will use this instruction to load constants only.
To tell kernel that user space needs a pointer the _pseudo_ variant of
this instruction may be added later, which will use extra bits of encoding
to indicate what type of pointer user space is asking kernel to provide.
For example 'off' or 'src_reg' fields can be used for such purpose.
src_reg = 1 could mean that user space is asking kernel to validate and
load in-kernel map pointer.
src_reg = 2 could mean that user space needs readonly data section pointer
src_reg = 3 could mean that user space needs a pointer to per-cpu local data
All such future pseudo instructions will not be carrying the actual pointer
as part of the instruction, but rather will be treated as a request to kernel
to provide one. The kernel will verify the request_for_a_pointer, then
will drop _pseudo_ marking and will store actual internal pointer inside
the instruction, so the end result is the interpreter and JITs never
see pseudo BPF_LD_IMM64 insns and only operate on generic BPF_LD_IMM64 that
loads 64-bit immediate into a register. User space never operates on direct
pointers and verifier can easily recognize request_for_pointer vs other
instructions.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nft_masq expression is intended to perform NAT in the masquerade flavour.
We decided to have the masquerade functionality in a separated expression other
than nft_nat.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Let's refactor the code so we can reach the masquerade functionality
from outside the xt context (ie. nftables).
The patch includes the addition of an atomic counter to the masquerade
notifier: the stuff to be done by the notifier is the same for xt and
nftables. Therefore, only one notification handler is needed.
This factorization only involves IPv6; a similar patch exists to
handle IPv4.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Let's refactor the code so we can reach the masquerade functionality
from outside the xt context (ie. nftables).
The patch includes the addition of an atomic counter to the masquerade
notifier: the stuff to be done by the notifier is the same for xt and
nftables. Therefore, only one notification handler is needed.
This factorization only involves IPv4; a similar patch follows to
handle IPv6.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Both SNAT and DNAT (and the upcoming masquerade) can have additional
configuration parameters, such as port randomization and NAT addressing
persistence. We can cover these scenarios by simply adding a flag
attribute for userspace to fill when needed.
The flags to use are defined in include/uapi/linux/netfilter/nf_nat.h:
NF_NAT_RANGE_MAP_IPS
NF_NAT_RANGE_PROTO_SPECIFIED
NF_NAT_RANGE_PROTO_RANDOM
NF_NAT_RANGE_PERSISTENT
NF_NAT_RANGE_PROTO_RANDOM_FULLY
NF_NAT_RANGE_PROTO_RANDOM_ALL
The caller must take care of not messing up with the flags, as they are
added unconditionally to the final resulting nf_nat_range.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add devgroup support to let us match device group of a packets incoming
or outgoing interface.
Signed-off-by: Ana Rey <anarey@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Move the specific NAT IPv6 core functions that are called from the
hooks from ip6table_nat.c to nf_nat_l3proto_ipv6.c. This prepares the
ground to allow iptables and nft to use the same NAT engine code that
comes in a follow up patch.
This also renames nf_nat_ipv6_fn to nft_nat_ipv6_fn in
net/ipv6/netfilter/nft_chain_nat_ipv6.c to avoid a compilation breakage.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
John W. Linville says:
====================
pull request: wireless-next 2014-09-08
Please pull this batch of updates intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
For the Bluetooth bits, Gustavo says:
"The changes consists of:
- Coding style fixes to HCI drivers
- Corrupted ack value fix for the H5 HCI driver
- A couple of Enhanced L2CAP fixes
- Conversion of SMP code to use common L2CAP channel API
- Page scan optimizations when using the kernel-side whitelist
- Various mac802154 and and ieee802154 6lowpan cleanups
- One new Atheros USB ID"
For the iwlwifi bits, Emmanuel says:
"We have a new big thing coming up which is called Dynamic Queue
Allocation (or DQA). This is a completely new way to work with the
Tx queues and it requires major refactoring. This is being done by
Johannes and Avri. Besides this, Johannes disables U-APSD by default
because of APs that would disable A-MPDU if the association supports
U-ASPD. Luca contributed to the power area which he was cleaning
up on the way while working on CSA. A few more random things here
and there."
For the Atheros bits, Kalle says:
"For ath6kl we had two small fixes and a new SDIO device id.
For ath10k the bigger changes are:
* support for new firmware version 10.2 (Michal)
* spectral scan support (Simon, Sven & Mathias)
* export a firmware crash dump file (Ben & me)
* cleaning up of pci.c (Michal)
* print pci id in all messages, which causes most of the churn (Michal)"
Beyond that, we have the usual collection of various updates to ath9k,
b43, mwifiex, and wil6210, as well as a few other bits here and there.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
inetpeer sequence numbers are no longer incremented, so no need to
check and flush the tree. The function that increments the sequence
number was already dead code and removed in in "ipv4: remove unused
function" (068a6e18). Remove the code that checks for a change, too.
Verifying that v4_seq and v6_seq are never incremented and thus that
flush_check compares bp->flush_seq to 0 is trivial.
The second part of the change removes flush_check completely even
though bp->flush_seq is exactly !0 once, at initialization. This
change is correct because the time this branch is true is when
bp->root == peer_avl_empty_rcu, in which the branch and
inetpeer_invalidate_tree are a NOOP.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix skb leak in mac802154, from Martin Townsend
2) Use select not depends on NF_NAT for NFT_NAT, from Pablo Neira
Ayuso
3) Fix union initializer bogosity in vxlan, from Gerhard Stenzel
4) Fix RX checksum configuration in stmmac driver, from Giuseppe
CAVALLARO
5) Fix TSO with non-accelerated VLANs in e1000, e1000e, bna, ehea,
i40e, i40evf, mvneta, and qlge, from Vlad Yasevich
6) Fix capability checks in phy_init_eee(), from Giuseppe CAVALLARO
7) Try high order allocations more sanely for SKBs, specifically if a
high order allocation fails, fall back directly to zero order pages
rather than iterating down one order at a time. From Eric Dumazet
8) Fix a memory leak in openvswitch, from Li RongQing
9) amd-xgbe initializes wrong spinlock, from Thomas Lendacky
10) RTNL locking was busted in setsockopt for anycast and multicast, fix
from Sabrina Dubroca
11) Fix peer address refcount leak in ipv6, from Nicolas Dichtel
12) DocBook typo fixes, from Masanari Iida
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
ipv6: restore the behavior of ipv6_sock_ac_drop()
amd-xgbe: Enable interrupts for all management counters
amd-xgbe: Treat certain counter registers as 64 bit
greth: moved TX ring cleaning to NAPI rx poll func
cnic : Cleanup CONFIG_IPV6 & VLAN check
net: treewide: Fix typo found in DocBook/networking.xml
bnx2x: Fix link problems for 1G SFP RJ45 module
3c59x: avoid panic in boomerang_start_xmit when finding page address:
netfilter: add explicit Kconfig for NETFILTER_XT_NAT
ipv6: use addrconf_get_prefix_route() to remove peer addr
ipv6: fix a refcnt leak with peer addr
net-timestamp: only report sw timestamp if reporting bit is set
drivers/net/fddi/skfp/h/skfbi.h: Remove useless PCI_BASE_2ND macros
l2tp: fix race while getting PMTU on PPP pseudo-wire
ipv6: fix rtnl locking in setsockopt for anycast and multicast
VMXNET3: Check for map error in vmxnet3_set_mc
openvswitch: distinguish between the dropped and consumed skb
amd-xgbe: Fix initialization of the wrong spin lock
openvswitch: fix a memory leak
netfilter: fix missing dependencies in NETFILTER_XT_TARGET_LOG
...
John W. Linville says:
====================
pull request: wireless 2014-09-05
Please pull this batch of fixes intended for the 3.17 stream...
For the mac80211 bits, Johannes says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
For the iwlwifi bits, Emmanuel says:
"I revert a patch that disabled CTS to self in dvm because users
reported issues. The revert is CCed to stable since the offending
patch was sent to stable too. I also bump the firmware API versions
since a new firmware is coming up. On top of that, Marcel fixes a
bug I introduced while fixing a bug in our Kconfig file."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix for recently broken test_suspend= command line argument
(Rafael J Wysocki).
- Fixes for regressions related to the ACPI video driver caused
by switching the default to native backlight handling in 3.16
from Hans de Goede.
- Fix for a sysfs attribute of ACPI device objects that returns
stale values sometimes due to the fact that they are cached
instead of executing the appropriate method (_SUN) every time
(broken in 3.14). From Yasuaki Ishimatsu.
- Fix for a deadlock between cpuidle_lock and cpu_hotplug.lock
in the ACPI processor driver from Jiri Kosina.
- Runtime output validation for the ACPI _DSD device configuration
object missing from the support for it that has been introduced
recently. From Mika Westerberg.
- Fix for an unuseful and misleading RAPL (Running Average Power
Limit) domain detection message in the RAPL driver from Jacob Pan.
- New Intel Haswell CPU ID for the RAPL driver from Jason Baron.
- New Clevo W350etq blacklist entry for the ACPI EC driver
from Lan Tianyu.
- Cleanup for the intel_pstate driver and the core generic PM
domains code from Gabriele Mazzotta and Geert Uytterhoeven.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=EzJF
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are regression fixes (ACPI sysfs, ACPI video, suspend test),
ACPI cpuidle deadlock fix, missing runtime validation of ACPI _DSD
output, a fix and a new CPU ID for the RAPL driver, new blacklist
entry for the ACPI EC driver and a couple of trivial cleanups
(intel_pstate and generic PM domains).
Specifics:
- Fix for recently broken test_suspend= command line argument (Rafael
Wysocki).
- Fixes for regressions related to the ACPI video driver caused by
switching the default to native backlight handling in 3.16 from
Hans de Goede.
- Fix for a sysfs attribute of ACPI device objects that returns stale
values sometimes due to the fact that they are cached instead of
executing the appropriate method (_SUN) every time (broken in
3.14). From Yasuaki Ishimatsu.
- Fix for a deadlock between cpuidle_lock and cpu_hotplug.lock in the
ACPI processor driver from Jiri Kosina.
- Runtime output validation for the ACPI _DSD device configuration
object missing from the support for it that has been introduced
recently. From Mika Westerberg.
- Fix for an unuseful and misleading RAPL (Running Average Power
Limit) domain detection message in the RAPL driver from Jacob Pan.
- New Intel Haswell CPU ID for the RAPL driver from Jason Baron.
- New Clevo W350etq blacklist entry for the ACPI EC driver from Lan
Tianyu.
- Cleanup for the intel_pstate driver and the core generic PM domains
code from Gabriele Mazzotta and Geert Uytterhoeven"
* tag 'pm+acpi-3.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / cpuidle: fix deadlock between cpuidle_lock and cpu_hotplug.lock
ACPI / scan: not cache _SUN value in struct acpi_device_pnp
cpufreq: intel_pstate: Remove unneeded variable
powercap / RAPL: change domain detection message
powercap / RAPL: add support for CPU model 0x3f
PM / domains: Make generic_pm_domain.name const
PM / sleep: Fix test_suspend= command line option
ACPI / EC: Add msi quirk for Clevo W350etq
ACPI / video: Disable native_backlight on HP ENVY 15 Notebook PC
ACPI / video: Add a disable_native_backlight quirk
ACPI / video: Fix use_native_backlight selection logic
ACPICA: ACPI 5.1: Add support for runtime validation of _DSD package.
Pull timer fixes from Thomas Gleixner:
"Three fixlets from the timer departement:
- Update the timekeeper before updating vsyscall and pvclock. This
fixes the kvm-clock regression reported by Chris and Paolo.
- Use the proper irq work interface from NMI. This fixes the
regression reported by Catalin and Dave.
- Clarify the compat_nanosleep error handling mechanism to avoid
future confusion"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Update timekeeper before updating vsyscall and pvclock
compat: nanosleep: Clarify error handling
nohz: Restore NMI safe local irq work for local nohz kick
