* pm-core:
PM / wakeirq: fix wakeirq setting after wakup re-configuration from sysfs
PM / runtime: Document steps for device removal
* powercap:
powercap: intel_rapl: Add missing Haswell model
* pm-tools:
tools/power turbostat: work around RC6 counter wrap
tools/power turbostat: initial KBL support
tools/power turbostat: initial SKX support
tools/power turbostat: decode BXT TSC frequency via CPUID
tools/power turbostat: initial BXT support
tools/power turbostat: print IRTL MSRs
tools/power turbostat: SGX state should print only if --debug
Sometimes the rc6 sysfs counter spontaneously resets,
causing turbostat prints a very large number
as it tries to calcuate % = 100 * (old - new) / interval
When we see (old > new), print ***.**% instead
of a bogus huge number.
Note that this detection is not fool-proof, as the counter
could reset several times and still result in new > old.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Hard-code BXT ART to 19200MHz, so turbostat --debug
can fully enumerate TSC:
CPUID(0x15): eax_crystal: 3 ebx_tsc: 186 ecx_crystal_hz: 0
TSC: 1190 MHz (19200000 Hz * 186 / 3 / 1000000)
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some processors use the Interrupt Response Time Limit (IRTL) MSR value
to describe the maximum IRQ response time latency for deep
package C-states. (Though others have the register, but do not use it)
Lets print it out to give insight into the cases where it is used.
IRTL begain in SNB, with PC3/PC6/PC7, and HSW added PC8/PC9/PC10.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The CPUID.SGX bit was printed, even if --debug was used
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Redesign of cpufreq governors and the intel_pstate driver to
make them use callbacks invoked by the scheduler to trigger CPU
frequency evaluation instead of using per-CPU deferrable timers
for that purpose (Rafael Wysocki).
- Reorganization and cleanup of cpufreq governor code to make it
more straightforward and fix some concurrency problems in it
(Rafael Wysocki, Viresh Kumar).
- Cleanup and improvements of locking in the cpufreq core (Viresh
Kumar).
- Assorted cleanups in the cpufreq core (Rafael Wysocki, Viresh
Kumar, Eric Biggers).
- intel_pstate driver updates including fixes, optimizations and a
modification to make it enable enable hardware-coordinated P-state
selection (HWP) by default if supported by the processor (Philippe
Longepe, Srinivas Pandruvada, Rafael Wysocki, Viresh Kumar, Felipe
Franciosi).
- Operating Performance Points (OPP) framework updates to improve
its handling of voltage regulators and device clocks and updates
of the cpufreq-dt driver on top of that (Viresh Kumar, Jon Hunter).
- Updates of the powernv cpufreq driver to fix initialization
and cleanup problems in it and correct its worker thread handling
with respect to CPU offline, new powernv_throttle tracepoint
(Shilpasri Bhat).
- ACPI cpufreq driver optimization and cleanup (Rafael Wysocki).
- ACPICA updates including one fix for a regression introduced
by previos changes in the ACPICA code (Bob Moore, Lv Zheng,
David Box, Colin Ian King).
- Support for installing ACPI tables from initrd (Lv Zheng).
- Optimizations of the ACPI CPPC code (Prashanth Prakash, Ashwin
Chaugule).
- Support for _HID(ACPI0010) devices (ACPI processor containers)
and ACPI processor driver cleanups (Sudeep Holla).
- Support for ACPI-based enumeration of the AMBA bus (Graeme Gregory,
Aleksey Makarov).
- Modification of the ACPI PCI IRQ management code to make it treat
255 in the Interrupt Line register as "not connected" on x86 (as
per the specification) and avoid attempts to use that value as
a valid interrupt vector (Chen Fan).
- ACPI APEI fixes related to resource leaks (Josh Hunt).
- Removal of modularity from a few ACPI drivers (BGRT, GHES,
intel_pmic_crc) that cannot be built as modules in practice (Paul
Gortmaker).
- PNP framework update to make it treat ACPI_RESOURCE_TYPE_SERIAL_BUS
as a valid resource type (Harb Abdulhamid).
- New device ID (future AMD I2C controller) in the ACPI driver for
AMD SoCs (APD) and in the designware I2C driver (Xiangliang Yu).
- Assorted ACPI cleanups (Colin Ian King, Kaiyen Chang, Oleg Drokin).
- cpuidle menu governor optimization to avoid a square root
computation in it (Rasmus Villemoes).
- Fix for potential use-after-free in the generic device properties
framework (Heikki Krogerus).
- Updates of the generic power domains (genpd) framework including
support for multiple power states of a domain, fixes and debugfs
output improvements (Axel Haslam, Jon Hunter, Laurent Pinchart,
Geert Uytterhoeven).
- Intel RAPL power capping driver updates to reduce IPI overhead in
it (Jacob Pan).
- System suspend/hibernation code cleanups (Eric Biggers, Saurabh
Sengar).
- Year 2038 fix for the process freezer (Abhilash Jindal).
- turbostat utility updates including new features (decoding of more
registers and CPUID fields, sub-second intervals support, GFX MHz
and RC6 printout, --out command line option), fixes (syscall jitter
detection and workaround, reductioin of the number of syscalls made,
fixes related to Xeon x200 processors, compiler warning fixes) and
cleanups (Len Brown, Hubert Chrzaniuk, Chen Yu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=cfty
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.6-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the majority of changes go into cpufreq and they are
significant.
First off, the way CPU frequency updates are triggered is different
now. Instead of having to set up and manage a deferrable timer for
each CPU in the system to evaluate and possibly change its frequency
periodically, cpufreq governors set up callbacks to be invoked by the
scheduler on a regular basis (basically on utilization updates). The
"old" governors, "ondemand" and "conservative", still do all of their
work in process context (although that is triggered by the scheduler
now), but intel_pstate does it all in the callback invoked by the
scheduler with no need for any additional asynchronous processing.
Of course, this eliminates the overhead related to the management of
all those timers, but also it allows the cpufreq governor code to be
simplified quite a bit. On top of that, the common code and data
structures used by the "ondemand" and "conservative" governors are
cleaned up and made more straightforward and some long-standing and
quite annoying problems are addressed. In particular, the handling of
governor sysfs attributes is modified and the related locking becomes
more fine grained which allows some concurrency problems to be avoided
(particularly deadlocks with the core cpufreq code).
In principle, the new mechanism for triggering frequency updates
allows utilization information to be passed from the scheduler to
cpufreq. Although the current code doesn't make use of it, in the
works is a new cpufreq governor that will make decisions based on the
scheduler's utilization data. That should allow the scheduler and
cpufreq to work more closely together in the long run.
In addition to the core and governor changes, cpufreq drivers are
updated too. Fixes and optimizations go into intel_pstate, the
cpufreq-dt driver is updated on top of some modification in the
Operating Performance Points (OPP) framework and there are fixes and
other updates in the powernv cpufreq driver.
Apart from the cpufreq updates there is some new ACPICA material,
including a fix for a problem introduced by previous ACPICA updates,
and some less significant changes in the ACPI code, like CPPC code
optimizations, ACPI processor driver cleanups and support for loading
ACPI tables from initrd.
Also updated are the generic power domains framework, the Intel RAPL
power capping driver and the turbostat utility and we have a bunch of
traditional assorted fixes and cleanups.
Specifics:
- Redesign of cpufreq governors and the intel_pstate driver to make
them use callbacks invoked by the scheduler to trigger CPU
frequency evaluation instead of using per-CPU deferrable timers for
that purpose (Rafael Wysocki).
- Reorganization and cleanup of cpufreq governor code to make it more
straightforward and fix some concurrency problems in it (Rafael
Wysocki, Viresh Kumar).
- Cleanup and improvements of locking in the cpufreq core (Viresh
Kumar).
- Assorted cleanups in the cpufreq core (Rafael Wysocki, Viresh
Kumar, Eric Biggers).
- intel_pstate driver updates including fixes, optimizations and a
modification to make it enable enable hardware-coordinated P-state
selection (HWP) by default if supported by the processor (Philippe
Longepe, Srinivas Pandruvada, Rafael Wysocki, Viresh Kumar, Felipe
Franciosi).
- Operating Performance Points (OPP) framework updates to improve its
handling of voltage regulators and device clocks and updates of the
cpufreq-dt driver on top of that (Viresh Kumar, Jon Hunter).
- Updates of the powernv cpufreq driver to fix initialization and
cleanup problems in it and correct its worker thread handling with
respect to CPU offline, new powernv_throttle tracepoint (Shilpasri
Bhat).
- ACPI cpufreq driver optimization and cleanup (Rafael Wysocki).
- ACPICA updates including one fix for a regression introduced by
previos changes in the ACPICA code (Bob Moore, Lv Zheng, David Box,
Colin Ian King).
- Support for installing ACPI tables from initrd (Lv Zheng).
- Optimizations of the ACPI CPPC code (Prashanth Prakash, Ashwin
Chaugule).
- Support for _HID(ACPI0010) devices (ACPI processor containers) and
ACPI processor driver cleanups (Sudeep Holla).
- Support for ACPI-based enumeration of the AMBA bus (Graeme Gregory,
Aleksey Makarov).
- Modification of the ACPI PCI IRQ management code to make it treat
255 in the Interrupt Line register as "not connected" on x86 (as
per the specification) and avoid attempts to use that value as a
valid interrupt vector (Chen Fan).
- ACPI APEI fixes related to resource leaks (Josh Hunt).
- Removal of modularity from a few ACPI drivers (BGRT, GHES,
intel_pmic_crc) that cannot be built as modules in practice (Paul
Gortmaker).
- PNP framework update to make it treat ACPI_RESOURCE_TYPE_SERIAL_BUS
as a valid resource type (Harb Abdulhamid).
- New device ID (future AMD I2C controller) in the ACPI driver for
AMD SoCs (APD) and in the designware I2C driver (Xiangliang Yu).
- Assorted ACPI cleanups (Colin Ian King, Kaiyen Chang, Oleg Drokin).
- cpuidle menu governor optimization to avoid a square root
computation in it (Rasmus Villemoes).
- Fix for potential use-after-free in the generic device properties
framework (Heikki Krogerus).
- Updates of the generic power domains (genpd) framework including
support for multiple power states of a domain, fixes and debugfs
output improvements (Axel Haslam, Jon Hunter, Laurent Pinchart,
Geert Uytterhoeven).
- Intel RAPL power capping driver updates to reduce IPI overhead in
it (Jacob Pan).
- System suspend/hibernation code cleanups (Eric Biggers, Saurabh
Sengar).
- Year 2038 fix for the process freezer (Abhilash Jindal).
- turbostat utility updates including new features (decoding of more
registers and CPUID fields, sub-second intervals support, GFX MHz
and RC6 printout, --out command line option), fixes (syscall jitter
detection and workaround, reductioin of the number of syscalls
made, fixes related to Xeon x200 processors, compiler warning
fixes) and cleanups (Len Brown, Hubert Chrzaniuk, Chen Yu)"
* tag 'pm+acpi-4.6-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (182 commits)
tools/power turbostat: bugfix: TDP MSRs print bits fixing
tools/power turbostat: correct output for MSR_NHM_SNB_PKG_CST_CFG_CTL dump
tools/power turbostat: call __cpuid() instead of __get_cpuid()
tools/power turbostat: indicate SMX and SGX support
tools/power turbostat: detect and work around syscall jitter
tools/power turbostat: show GFX%rc6
tools/power turbostat: show GFXMHz
tools/power turbostat: show IRQs per CPU
tools/power turbostat: make fewer systems calls
tools/power turbostat: fix compiler warnings
tools/power turbostat: add --out option for saving output in a file
tools/power turbostat: re-name "%Busy" field to "Busy%"
tools/power turbostat: Intel Xeon x200: fix turbo-ratio decoding
tools/power turbostat: Intel Xeon x200: fix erroneous bclk value
tools/power turbostat: allow sub-sec intervals
ACPI / APEI: ERST: Fixed leaked resources in erst_init
ACPI / APEI: Fix leaked resources
intel_pstate: Do not skip samples partially
intel_pstate: Remove freq calculation from intel_pstate_calc_busy()
intel_pstate: Move intel_pstate_calc_busy() into get_target_pstate_use_performance()
...
MSR_CONFIG_TDP_NOMINAL:
should print all 8 bits of base_ratio (bit 0:7) 0xFF
MSR_CONFIG_TDP_LEVEL_1:
should print all 15 bits of PKG_MIN_PWR_LVL1 (bit 48:62) 0x7FFF
should print all 15 bits of PKG_MAX_PWR_LVL1 (bit 32:46) 0x7FFF
should print all 8 bits of LVL1_RATIO (bit 16:23) 0xFF
should print all 15 bits of PKG_TDP_LVL1 (bit 0:14) 0x7FFF
And the same modification to MSR_CONFIG_TDP_LEVEL_2.
MSR_TURBO_ACTIVATION_RATIO:
should print all 8 bits of MAX_NON_TURBO_RATIO (bit 0:7) 0xFF
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
MSR_NHM_SNB_PKG_CST_CFG_CTL: 0x1e008008 (...pkg-cstate-limit=0: unlimited)
should print as
MSR_NHM_SNB_PKG_CST_CFG_CTL: 0x1e008008 (...pkg-cstate-limit=8: unlimited)
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat already checks whether calling each cpuid leavf is legal,
and it doesn't look at the function return value,
so call the simpler gcc intrinsic __cpuid() instead of __get_cpuid().
syntax only, no functional change
Signed-off-by: Len Brown <len.brown@intel.com>
The accuracy of Bzy_Mhz and Busy% depend on reading
the TSC, APERF, and MPERF close together in time.
When there is a very short measurement interval,
or a large system is profoundly idle, the changes
in APERF and MPERF may be very small.
They can be small enough that an expensive interrupt
between reading APERF and MPERF can cause the APERF/MPERF
ratio to become inaccurate, resulting in invalid
calculation and display of Bzy_MHz.
A dummy APERF read of APERF makes this problem
much more rare. Apparently this 1st systemn call
after exiting a long stretch of idle is when we
typically see expensive timer interrupts that cause
large jitter.
For the cases that dummy APERF read fails to prevent,
we compare the latency of the APERF and MPERF reads.
If they differ by more than 2x, we re-issue them.
Signed-off-by: Len Brown <len.brown@intel.com>
The column "GFX%c6" show the percentage of time the GPU
is in the "render C6" state, rc6. Deep package C-states on several
systems depend on the GPU being in RC6.
This information comes from the counter
/sys/class/drm/card0/power/rc6_residency_ms,
as read before and after the measurement interval.
Signed-off-by: Len Brown <len.brown@intel.com>
Under the column "GFXMHz", show a snapshot of this attribute:
/sys/class/graphics/fb0/device/drm/card0/gt_cur_freq_mhz
This is an instantaneous snapshot of what sysfs presents
at the end of the measurement interval. turbostat does
not average or otherwise perform any math on this value.
Signed-off-by: Len Brown <len.brown@intel.com>
The new IRQ column shows how many interrupts have occurred on each CPU
during the measurement inteval. This information comes from
the difference between /proc/interrupts shapshots made before
and after the measurement interval.
The first row, the system summary, shows the sum of the IRQS
for all CPUs during that interval.
Signed-off-by: Len Brown <len.brown@intel.com>
skip the open(2)/close(2) on each msr read
by keeping the /dev/cpu/*/msr files open.
The remaining read(2) is generally far fewer cycles
than the removed open(2) system call.
Signed-off-by: Len Brown <len.brown@intel.com>
By default...
Turbostat --debug gconfiguration info goes to stderr.
In FORK mode, turbostat statistics go to stderr.
In PERIODIC mode, turbostat statistics go to stdout.
These defaults do not change, but an option "--out file"
will send all output above only to the specified file.
Signed-off-by: Len Brown <len.brown@intel.com>
some tools processing turbostat output
have difficulty with items that begin with %...
Reported-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Following changes have been made:
- changed MSR_NHM_TURBO_RATIO_LIMIT to MSR_TURBO_RATIO_LIMIT in debug print
for consistency with Developer Manual
- updated definition of bitfields in MSR_TURBO_RATIO_LIMIT and appropriate
parsing code
- added x200 to list of architectures that do not support Nahlem compatible
definition of MSR_TURBO_RATIO_LIMIT register (x200 has the register but
bits definition is custom)
- fixed typo in code that parses MSR_TURBO_RATIO_LIMIT
(logical instead of bitwise operator)
- changed MSR_TURBO_RATIO_LIMIT parsing algorithm so the print out had the
same order as implementations for other platforms
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
x200 does not enable any way to programmatically obtain bus clock
speed. Bclk for the architecture has a fixed value of 100 MHz.
At the same time x200 cannot be included in has_snb_msrs since
it does not support C7 idle state.
prior to this patch, MHz values reported on this chip
were erroneously calculated using bclk of 133MHz,
causing MHz values to be reported 33% higher than actual.
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat -i interval_sec
will sample and display statistics every interval_sec.
interval_sec used to be a whole number of seconds,
but now we accept a decimal, as small as 0.001 sec (1 ms).
Signed-off-by: Len Brown <len.brown@intel.com>
When building with gcc 6 we're getting various build warnings that just
require some trivial function declaration and call fixes:
turbostat.c: In function ‘dump_cstate_pstate_config_info’:
turbostat.c:1973:1: warning: type of ‘family’ defaults to ‘int’
dump_cstate_pstate_config_info(family, model)
turbostat.c:1973:1: warning: type of ‘model’ defaults to ‘int’
turbostat.c: In function ‘get_tdp’:
turbostat.c:2145:8: warning: type of ‘model’ defaults to ‘int’
double get_tdp(model)
turbostat.c: In function ‘perf_limit_reasons_probe’:
turbostat.c:2259:6: warning: type of ‘family’ defaults to ‘int’
void perf_limit_reasons_probe(family, model)
turbostat.c:2259:6: warning: type of ‘model’ defaults to ‘int’
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/n/tip-wbicer8n0s9qe6ql8h9x478e@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
for debugging, dump a few more fields:
CPUID(1): SSE3 MONITOR EIST TM2 TSC MSR ACPI-TM TM
cpu0: MSR_IA32_MISC_ENABLE: 0x00850089 (TCC EIST MONITOR)
Signed-off-by: Len Brown <len.brown@intel.com>
MSR_PLATFORM_INFO is the new name for MSR_NHM_PLATFORM_INFO
no functional change
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
MSR_TURBO_ACTIVATION_RATIO: 0x00000016 (MAX_NON_TURBO_RATIO=6 lock=0)
should print all 7 bits of MAX_NON_TURBO_RATIO (in decimal):
MSR_TURBO_ACTIVATION_RATIO: 0x00000016 (MAX_NON_TURBO_RATIO=22 lock=0)
Signed-off-by: Len Brown <len.brown@intel.com>
Bzy_MHz = TSC_delta*tsc_tweak/APERF_delta/MPERF_delta/measurement_interval
becomes
Bzy_MHz = base_mhz/APERF_delta/MPERF_delta
on systems which support MSR_NHM_PLATFORM_INFO.
base_mhz is calculated directly from the base_ratio
reported in MSR_NHM_PLATFORM_INFO * bclk,
and bclk is discovered via MSR or cpuid.
This reduces the dependency of Bzy_MHz calculation on the TSC.
Previously, there were 4 TSC readings required in each caculation,
the raw TSC delta combined with the measurement_interval.
This also removes the "tsc_tweak" correction factor used when
TSC runs on a different base clock from the CPU's bclk.
After this change, tsc_tweak is used only for %Busy.
The end-result should be a Bzy_MHz result slightly less prone to jitter.
Signed-off-by: Len Brown <len.brown@intel.com>
On a Skylake with 1500MHz base frequency,
the TSC runs at 1512MHz.
This is because the TSC is no longer in the n*100 MHz BCLK domain,
but is now in the m*24MHz crystal clock domain. (24 MHz * 63 = 1512 MHz)
This adds error to several calculations in turbostat,
unless the TSC sample sizes are adjusted for this difference.
Note that calculations in the time domain are immune
from this issue, as the timing sub-system has already
calibrated the TSC against a known wall clock.
AVG_MHz = APERF_delta/measurement_interval
need no adjustment. APERF_delta is in the BCLK domain,
and measurement_interval is in the time domain.
TSC_MHz = TSC_delta/measurement_interval
needs no adjustment -- as we really do want to report
the actual measured TSC delta here, and measurement_interval
is in the accurate time domain.
%Busy = MPERF_delta/TSC_delta
needs adjustment to use TSC_BCLK_DOMAIN_delta.
TSC_BCLK_DOMAIN_delta = TSC_delta * base_hz / tsc_hz
Bzy_MHz = TSC_delta/APERF_delta/MPERF_delta/measurement_interval
need adjustment as above.
No other metrics in turbostat need to be adjusted.
Before:
CPU Avg_MHz %Busy Bzy_MHz TSC_MHz
- 550 24.84 2216 1512
0 2191 98.73 2219 1514
2 0 0.01 2130 1512
1 9 0.43 2016 1512
3 2 0.08 2016 1512
After:
CPU Avg_MHz %Busy Bzy_MHz TSC_MHz
- 550 25.05 2198 1512
0 2190 99.62 2199 1512
2 0 0.01 2152 1512
1 9 0.46 2000 1512
3 2 0.10 2000 1512
Note that in this example, the "Before" Bzy_MHz
was reported as exceeding the 2200 max turbo rate.
Also, even a pinned spin loop would not be reported
as over 99% busy.
Signed-off-by: Len Brown <len.brown@intel.com>
KNL increments APERF and MPERF every 1024 clocks.
This is compliant with the architecture specification,
which requires that only the ratio of APERF/MPERF need be valid.
However, turbostat takes advantage of the fact that these
two MSRs increment every un-halted clock
at the actual and base frequency:
AVG_MHz = APERF_delta/measurement_interval
%Busy = MPERF_delta/TSC_delta
This quirk is needed for these calculations to also work on KNL,
which would otherwise show a value 1024x smaller than expected.
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Staring in Linux-4.3-rc1,
commit 6fb3143b56 ("tools/power turbostat: dump CONFIG_TDP")
touches MSR 0x648, which is not supported on IVB-Xeon.
This results in "turbostat --debug" exiting on those systems:
turbostat: /dev/cpu/2/msr offset 0x648 read failed: Input/output error
Remove IVB-Xeon from the list of machines supporting with that MSR.
Signed-off-by: Len Brown <len.brown@intel.com>
Pull turbostat changes for v4.3 from Len Brown.
* 'turbostat' of https://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: fix typo on DRAM column in Joules-mode
tools/power turbostat: fix parameter passing for forked command
tools/power turbostat: dump CONFIG_TDP
tools/power turbostat: cpu0 is no longer hard-coded, so update output
tools/power turbostat: update turbostat(8)
turbostat supports forked command when sampling cpu state. However,
the forked command is not allowed to be executed with options, otherwise
turbostat might regard these options as invalid turbostat options.
For example:
./turbostat stress -c 4 -t 10
./turbostat: unrecognized option '-t'
Reported-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Config TDP is a feature that allows parts to be configured
for different thermal limits after they have left the factory.
This can have an effect on the operation of the part,
particularly in determiniing...
Max Non-turbo Ratio
Turbo Activation Ratio
Signed-off-by: Len Brown <len.brown@intel.com>
The --debug option reads a number of per-package MSRs.
Previously we explicitly read them on cpu0, but recently
turbostat changed to read them on the current "base_cpu".
Update the print-out to reflect base_cpu, rather than
the hard-coded cpu0.
Signed-off-by: Len Brown <len.brown@intel.com>
This header containing all MSRs and respective bit definitions
got exported to userspace in conjunction with the big UAPI
shuffle.
But, it doesn't belong in the UAPI headers because userspace can
do its own MSR defines and exporting them from the kernel blocks
us from doing cleanups/renames in that header. Which is
ridiculous - it is not kernel's job to export such a header and
keep MSRs list and their names stable.
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1433436928-31903-19-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Remove reference to the original Nehalem Turbo white paper,
since it has moved, and these mechanisms have now long since
been documented in the Software Developer's Manual.
Reported-by: Jeremie Lagraviere <jeremie@simula.no>
Signed-off-by: Len Brown <len.brown@intel.com>
Linux-3.7 added CONFIG_BOOTPARAM_HOTPLUG_CPU0,
allowing systems to offline cpu0.
But when cpu0 is offline, turbostat will not run:
# turbostat ls
turbostat: no /dev/cpu/0/msr
This patch replaces the hard-coded use of cpu0 in turbostat
with the current cpu, allowing it to run without a cpu0.
Fewer cross-calls may also be needed due to use of current cpu,
though this hard-coding was used only for the --debug preamble.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
When EPB is 0xF, turbosat was incorrectly describing it as "custom"
instead of calling it "powersave":
< cpu0: MSR_IA32_ENERGY_PERF_BIAS: 0x0000000f (custom)
> cpu0: MSR_IA32_ENERGY_PERF_BIAS: 0x0000000f (powersave)
Signed-off-by: Len Brown <len.brown@intel.com>
Changes mainly to account for minor differences in Knights Landing(KNL):
1. KNL supports C1 and C6 core states.
2. KNL supports PC2, PC3 and PC6 package states.
3. KNL has a different encoding of the TURBO_RATIO_LIMIT MSR
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Without this update, turbostat displays only 2 threads per core.
Some processors, such as Xeon Phi, have more.
Signed-off-by: Dasaratharaman Chandramouli <dasaratharaman.chandramouli@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
HSW expanded MSR_PKG_CST_CONFIG_CONTROL.Package-C-State-Limit,
from bits[2:0] used by previous implementations, to [3:0].
The value 1000b is unlimited, and is used by BDW and SKL too.
Signed-off-by: Len Brown <len.brown@intel.com>
