If we fail to allocate rx buffers pool by any reason, we'll just return
with an error, however we've previously successfully requested an irq. Fix
this by releasing the irq before returning the error.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when FIFO_ERR happens, we stop the dma, wait for it to become
idle and then reset the whole MAC_RX logic (and after that we must re-set
multicast addresses and also re-enable MAC_RX when we're finally ready to
accept new packets). This leads to CRC errors on high number of incoming
packets and is not needed according to the datasheet.
This patch fixes it by the following steps:
1) remove this reset in pch_gbe_stop_receive(), which causes some functions
to not be used anywhere
2) remove already unused functions pch_gbe_wait_clr_bit_irq() and
pch_gbe_mac_reset_rx() to correctly build
3) move pch_gbe_enable_mac_rx() out of pch_gbe_start_receive() to
pch_gbe_up() where it's only needed after we've removed the MAC_RX reset
4) rename pch_gbe_start/stop_receive() to pch_gbe_enable/disable_dma_rx()
to more precisely reflect what the functions are now doing.
After these changes we already don't see the CRC errors and gain some
increase in RX processing speed.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we were in RX_FIFO_ERR state and entered pch_gbe_napi_poll(), we'll
anyway clean some rx space and thus can continue to receive more packets.
Currently, we re-set the RX_FIFO_ERR in situations when we've exhausted our
budget for RX cleaning or cleaned some TX packets. Removing it gives us
+20%-40% speed increase and a lot less of RX_FIFO_ERRors reported.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move MAC_RX-related bits into separate functions.
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before use the request and response queue addr, make sure it has wrote
to the registers.
Signed-off-by: Joe Jin <joe.jin@oracle.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
This is a batch of fixes intended for the 3.7 stream.
Dan Carpenter brings a fix for a simple signedness bug that could
prevent the proper termination of a loop.
Felix Fietkau found a few more places that need to use
ieee80211_free_txskb for properly releasing SKBs used by mac80211.
Franky Lin offers a pair of brcmfmac fixes, both fixing simple state
reporting errors.
Hante Meuleman corrects an error reporting case that wasn't handling
all types of errors properly.
Johan Hedberg offers a fix for an issue discovered at the Bluetooth
UnPlug Fest. Gustavo says "the patch fixes a failure to pair with
devices that support the LE Secure Connections feature."
Johannes Berg sends an iwlwifi fix to handle a message type that
is too large for the normal command mechanism. He also provides a
mac80211 fix to use HT20 channels when HT40 channels are not permitted.
Jouni Malinen offers a mac80211 fix for a masking error that was
incorrectly marking some frames.
Piotr Haber provides a fix to make sure bcma devices are unregistered
properly.
Stanislav Yakovlev gives us a fix for a panic in the ipw2200 driver.
Stanislaw Gruszka sends a pair of fixes: one prevents a mismatch on
connection states between cfg80211 and mac80211; the other prevents
some frame corruption related to handling encryption.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch also fixes the build failure caused due to removal of #ifdef
CONFIG_CHELSIO_T4_OFFLOAD condition
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver add support for wake over lan on AT803x phys.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that the iPhone ethernet driver did not support
iPhone 5. I quickly added support to it in my kernel, here's
a patch.
Signed-off-by: Jay Purohit <jspurohit@velocitylimitless.com>
Acked-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Jan Ceuleers <jan.ceuleers@computer.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix regression in /proc/net/if_inet6, sometimes devices do not get
listed. From Eric Dumazet.
2) Add IPSEC networking sub-section to MAINTAINERS.
3) S390 networking fixes from Hendrik Brueckner and Stefan Raspl.
4) Fix enslavement of devices that can't do VLAN properly, from Jiri
Pirko.
5) SCTP sack handling fix from Zijie Pan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
ipv6: addrconf: fix /proc/net/if_inet6
bnx2x: fix handling mf storage modes
qeth: fix deadlock between recovery and bonding driver
smsgiucv: reestablish IUCV path after resume
sctp: fix call to SCTP_CMD_PROCESS_SACK in sctp_cmd_interpreter()
vlan: fix bond/team enslave of vlan challenged slave/port
MAINTAINERS: Add explicit section for IPSEC networking.
Pull sparc fixes from David Miller:
"Two sparc64 perf bug fixes and add a sysrq facility so I can diagnose
these kinds of problems more quickly in the future."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix bit twiddling in sparc_pmu_enable_event().
sparc64: Add global PMU register dumping via sysrq.
sparc64: Like x86 we should check current->mm during perf backtrace generation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEUEABECAAYFAlB7pNUACgkQGkmNcg7/o7jjUgCgoki88QEhqCSwo7oHwTTKc101
K0gAli6kneoMMHfO9w9dMlGz78EI5FQ=
=JEFo
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH updates from Paul Mundt.
The bulk of this is the UAPI disintegration for SH.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Fix up more fallout from pointless ARM __iomem churn.
sh: Wire up kcmp syscall.
UAPI: (Scripted) Disintegrate arch/sh/include/asm
Pull drm fixes from Dave Airlie:
"Fixes for i915, nouveau and radeon:
- i915: haswell stability, modeset rework fallout, ums fix
- nouveau: misc fixes from code rework
- radeon: pll rework fixes, more 2 level PTE cleanups.
- core: warning fixes on 32-bit."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
nouveau: fix warning on 32-bit build.
drm/nouveau/bios: fix typo in error message
drm/nouveau: only call ttm_agp_tt_create when __OS_HAS_AGP
drm/nv50/fb: fix double free of vram mm
drm/nouveau/pm: do not stop reclocking if failing to set the fan speed
drm/nouveau/pm: fix a typo related to the move to the therm subdev
drm/nouveau/hwmon: fix the initialization condition
drm: fix warning on 32-bit.
drm: radeon: fix printk format warning
drm/radeon: fix spelling typos in debugging output
drm/radeon: Don't destroy I2C Bus Rec in radeon_ext_tmds_enc_destroy().
drm/radeon: check if pcie gen 2 is already enabled (v2)
drm/radeon/cayman: set VM max pfn at MC init
drm/radeon: separate pt alloc from lru add
drm/radeon: don't add the IB pool to all VMs v2
drm/radeon: allocate page tables on demand v4
drm/radeon: update comments to clarify VM setup (v2)
drm/radeon: allocate PPLLs from low to high
drm/radeon: fix compilation with backlight disabled
drm/radeon: use %zu for formatting size_t
...
- duplicate includes, section markup, code mishaps
- erroneous return value in errorpath on the bcm2835 driver
- remove an unused sirf function that was causing build errors
- multiple-platform compilation stubs and a missed code review
comment fixup on the nomadik pin controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=vBpq
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
"A number of pinctrl fixes for the v3.7 series:
- duplicate includes, section markup, code mishaps
- erroneous return value in errorpath on the bcm2835 driver
- remove an unused sirf function that was causing build errors
- multiple-platform compilation stubs and a missed code review
comment fixup on the nomadik pin controller"
* tag 'pinctrl-fixes-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/nomadik: always use the simple irqdomain
pinctrl/nomadik: provide stubs for legacy Nomadik
pinctrl: remove duplicated include from pinctrl-xway.c
pinctrl: sirf: remove sirfsoc_gpio_set_pull function
pinctrl: fix return value in bcm2835_pinctrl_probe()
pinctrl: remove duplicated include from pinctrl-bcm2835.c
pinctrl: bcm2835: Use existing pointer to struct device
pinctrl: samsung: use __devinit section for init code
Merge emailed patches from Corey Minyard:
"Remove some bogus docs, Fix ACPI/IPMI interactions, fix some warnings,
and add register spacing detection for PCI interfaces."
* ipmi:
IPMI: Detect register spacing on PCI interfaces
IPMI: Fix some uninitialized warning
IPMI: Change link order
ACPI: Reorder IPMI driver before any other ACPI drivers
IPMI: Remove SMBus driver info from the docs
The IPMI spec defines a way to detect register spacing for PCI interfaces,
so implement it.
Signed-off-by: Steven Hsieh <sshsieh@broadcom.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was a spot where the compiler couldn't tell some variables
would be set. So initialize them to make the warning go away.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IPMI must be initialised before ACPI in order to ensure that any IPMI
services are available before ACPI driver initialisation attempts to use
any IPMI operation regions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drivers may make calls that require the ACPI IPMI driver to have been
initialised already, so make sure that it appears earlier in the build
order.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since commit a3348722 AFEX FCoE function is continuously reset.
The patch prevents the resetting and removes debug print
to stop garbaging syslog.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recovery thread, when failing, tears down the respective interface. To do
so, it needs to obtain the rtnl lock first, as the interface configuration is
changed.
If another process tries to modify an interface setting at the same time, that
process can obtain the rtnl lock first, but the respective callback in the qeth
driver will block until recovery has completed - which cannot happen since the
calling process already obtained it.
In one particular case, the bonding driver acquired the rtnl lock to modify the
card's MAC address, while the recovery failed at the same time due to the card
being removed. Hence qeth_l2_set_mac_address (implicitly holding the rtnl lock)
was waiting on qeth_l2_recover, which deadlocked when waiting on the rtnl lock.
This patch uses rtnl_trylock instead of rtnl_lock in the recovery thread. If the
lock cannot be obtained, the interface will be left up, but the card state
remains in CARD_STATE_RECOVER, which will prevent any further activities on the
card.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
smsg_pm_restore_thaw() uses wrong checking before reconnecting
the IUCV path to *MSG. It is corrected with this patch.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vlan_uses_dev() check for number of vlan devs rather than existence
of vlan_info. The reason is that vlan id 0 is there without appropriate
vlan dev on it by default which prevented from enslaving vlan challenged
dev.
Reported-by: Jon Stanley <jstanley@rmrf.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The channel switch command for 6000 series devices
is larger than the maximum inline command size of
320 bytes. The command is therefore refused with a
warning. Fix this by allocating the command and
using the NOCOPY mechanism.
Cc: stable@kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
minor set of nouveau fixes.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/bios: fix typo in error message
drm/nouveau: only call ttm_agp_tt_create when __OS_HAS_AGP
drm/nv50/fb: fix double free of vram mm
drm/nouveau/pm: do not stop reclocking if failing to set the fan speed
drm/nouveau/pm: fix a typo related to the move to the therm subdev
drm/nouveau/hwmon: fix the initialization condition
ttm_agp_tt_create is itself defined under CONFIG_AGP, so there's no
point calling it otherwise.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_fb_destroy already calls nouveau_mm_fini on vram mm.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
With the introduction of fan management modes, fan may not be drivable.
We should allow reclocking nonetheless.
This return was stupid to begin with since it may have left the card
in an intermediate state (clocks corresponding to a perflvl and voltage
corresponding to another one). The reclocking code will need to be
rewritten in a near-future in order to provide a better error handling.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Vekin on IRC
Reported-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
drivers/gpu/drm/radeon/radeon_atpx_handler.c:151:3: warning: format '%lu' expects type 'long unsigned int', but argument 2 has type 'size_t'
[airlied: Alex had others fixed already, except for atpx one]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex writes:
"This is the first -fixes pull for 3.7. I would have preferred
to have gotten it out a bit sooner, but I was on holiday last week.
- Cleanup of the new 2 level page table code it get it in
better shape and using less memory.
- Fix some display issues related to the PLL rework.
- Fix some cmpiler warnings and errors with certain config
options.
- Other misc bug fixes."
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix spelling typos in debugging output
drm/radeon: Don't destroy I2C Bus Rec in radeon_ext_tmds_enc_destroy().
drm/radeon: check if pcie gen 2 is already enabled (v2)
drm/radeon/cayman: set VM max pfn at MC init
drm/radeon: separate pt alloc from lru add
drm/radeon: don't add the IB pool to all VMs v2
drm/radeon: allocate page tables on demand v4
drm/radeon: update comments to clarify VM setup (v2)
drm/radeon: allocate PPLLs from low to high
drm/radeon: fix compilation with backlight disabled
drm/radeon: use %zu for formatting size_t
Daniel writes:
"- some register magic to fix hsw crw (Paulo&Ben)
- fix backlight destruction for cpu edp (Jani)
- fix gen ch7xxx dvo ->get_hw_state
- fixup the plane->pipe fixup code, the broken version massively angers
the modeset sanity checks
- kill pipe A quirk for i855gm, otherwise I get a black screen with the
above patch
- fixup for gem_get_page helper (Chris)
- fixup guardband clipping w/a (Ken), without this mesa master can erronously
drop vertices on snb, mesa 9.0 has the optimization reverted
- another pageflip vs. modeset fix
- kill bogus BUG_ON which broke ums+gem from Willy Tarreau (gasp, people
are still using this!)"
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: fix non-DP-D eDP backlight cleanup and module reload
drm/i915: HSW CRW stability magic
drm/i915/dvo-ch7xxx: fix get_hw_state
drm/i915: fixup the plane->pipe fixup code
drm/i915: rip out the pipe A quirk for i855gm
drm/i915: disable wc gtt pte mappings on gen2
drm/i915: fixup i915_gem_object_get_page inline helper
drm/i915: Disallow preallocation of requests
drm/i915: Set guardband clipping workaround bit in the right register.
drm/i915: paper over a pipe-enable vs pageflip race
drm/i915: remove useless BUG_ON which caused a regression in 3.5.
Commit 0236141837 ("thermal: add generic cpufreq cooling
implementation") requires cpufreq_frequency_get_table(), but that
function is only defined for CONFIG_CPU_FREQ_TABLE resulting in the
following build error:
drivers/built-in.o: In function `cpufreq_get_max_state':
drivers/thermal/cpu_cooling.c:259: undefined reference to `cpufreq_frequency_get_table'
drivers/built-in.o: In function `get_cpu_frequency':
drivers/thermal/cpu_cooling.c:129: undefined reference to `cpufreq_frequency_get_table'
Fix it by selecting CONFIG_CPU_FREQ_TABLE for such a configuration.
It turns out CONFIG_EXYNOS_THERMAL also needs CONFIG_CPU_FREQ_TABLE, so
select it there as well.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver does not count space of radiotap fields when allocating skb for
radiotap packet. This leads to kernel panic with the following call trace:
...
[67607.676067] [<c152f90f>] error_code+0x67/0x6c
[67607.676067] [<c142f831>] ? skb_put+0x91/0xa0
[67607.676067] [<f8cf5e5b>] ? ipw_handle_promiscuous_tx+0x16b/0x2d0 [ipw2200]
[67607.676067] [<f8cf5e5b>] ipw_handle_promiscuous_tx+0x16b/0x2d0 [ipw2200]
[67607.676067] [<f8cf899b>] ipw_net_hard_start_xmit+0x8b/0x90 [ipw2200]
[67607.676067] [<f8741c5a>] libipw_xmit+0x55a/0x980 [libipw]
[67607.676067] [<c143d3e8>] dev_hard_start_xmit+0x218/0x4d0
...
This bug was found by VittGam.
https://bugzilla.kernel.org/show_bug.cgi?id=43255
Cc: stable@kernel.org
Signed-off-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cores are unregistered, entries
need to be removed from cores list in a safe manner.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem here is that we loop until "remained_buf_len" is less than
zero, but since it is unsigned, it never is.
"remained_buf_len" has to be large enough to hold the value from
"mgmt_ie_buf_len". That variable is type u32, but it only holds small
values so I have changed to both variables to int.
Also I removed the bogus initialization from "mgmt_ie_buf_len" so that
GCC can detect if it is used unitialized. I moved the declaration of
"remained_buf_len" closer to where it is used so it's easier to read.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mode of WiFi dongle should be initialized in brcmf_cfg80211_up
which get called when network interface is brought up. Otherwise
brcmf_cfg80211_get_station would return error.
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Channel reported in scan results passed to cfg80211 is control
channel. But chanspec is reported while notifying cfg80211 about
roamed update. Cfg80211 complains because it could not find the
bss in the list. Report control channel while calling
cfg80211_roamed.
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in brcmf_usb_probe_cb only return code ENOLINK was seen as an
error. This is wrong, all error codes should be returned to usb
subsystem.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
radeon_i2c_fini() walks thru the list of I2C bus recs rdev->i2c_bus[]
to destroy each of them.
radeon_ext_tmds_enc_destroy() however also has code to destroy it's
associated I2C bus rec which has been obtained by radeon_i2c_lookup()
and is therefore also in the i2c_bus[] list.
This causes a double free resulting in a kernel panic when unloading
the radeon driver.
Removing destroy code from radeon_ext_tmds_enc_destroy() fixes this
problem.
agd5f: fix compiler warning
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
No need to emit them at VM flush as we no longer use
variable sized page tables now that we support 2 level
page tables. This matches the behavior of SI (which
does not support variable sized page tables).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Veaceslav Falico