Unwind the modified table_ptr and restore it to the local copy
upon any subsequent failures in the rproc_start() function. This
keeps the function to remain balanced on failures without the need
to balance any modified variables elsewhere.
While at this, do some minor cleanup of the extra lines between
the failure labels as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
[bjorn: unconditionally set table_ptr to cached_table]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
GCC_MSS_AXIS2 clock is used for disabling boot IMEM (a part of
AP boot up). With Boot IMEM disable now a part TZ/ATF, AXIS2
clock is no longer required post AP boot up and expected to
remain untouched. However if the clock is turned ON after Q6
is brought out of reset and later turned off, it results in
modem hang. When Q6 attempts a power collapse the internal
handshaking to check if AXIS2 is idle never goes through since
it is turned off preventing the RSC from getting triggered,
leaving modem in a funky state. Hence removing AXIS2 clk
enable/disable from the driver.
Reported-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The new driver only works as built-in code at the moment but fails
with a link error when configured as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/remoteproc/qcom_q6v5.o
see include/linux/module.h for more information
ERROR: "qcom_q6v5_init" [drivers/remoteproc/qcom_q6v5_pil.ko] undefined!
ERROR: "qcom_q6v5_wait_for_start" [drivers/remoteproc/qcom_q6v5_pil.ko] undefined!
ERROR: "qcom_q6v5_prepare" [drivers/remoteproc/qcom_q6v5_pil.ko] undefined!
ERROR: "qcom_q6v5_unprepare" [drivers/remoteproc/qcom_q6v5_pil.ko] undefined!
ERROR: "qcom_q6v5_request_stop" [drivers/remoteproc/qcom_q6v5_pil.ko] undefined!
ERROR: "qcom_q6v5_init" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_q6v5_wait_for_start" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_q6v5_prepare" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_q6v5_unprepare" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_q6v5_request_stop" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
This exports the internal symbols as needed and adds the MODULE_LICENSE()
and MODULE_DESCRIPTION() tags. I could not figure out the author, so I
did not add a MODULE_AUTHOR() tag for now.
Fixes: 3b415c8fb2 ("remoteproc: q6v5: Extract common resource handling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
On rare occasions a subdevice might need to prepare some hardware
resources before a remote processor is booted, and clean up some
state after it has been shut down.
One such example is the IP Accelerator found in various Qualcomm
platforms, which is accessed directly from both the modem remoteproc
and the application subsystem and requires an intricate lockstep
process when bringing the modem up and down.
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[elder@linaro.org: minor description and comment edits]
Signed-off-by Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rename functions used when subdevices are started and stopped to
reflect the new naming scheme.
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In preparation of adding the additional prepare and unprepare operations
make the client responsible for filling out the function pointers of the
rproc_subdev. This makes the arguments to rproc_add_subdev() more
manageable, in particular when some of the functions are left out.
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[elder@linaro.org: added comment about assigning function pointers]
Signed-off-by Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Some subdevices, such as glink ssr only care about the stop operation,
so make the operations optional to reduce client code.
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
"start" and "stop" are more suitable names for how these two operations
are used, and they fit better with the upcoming introduction of two
additional operations in the struct.
Tested-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[elder@linaro.org: minor comment edits]
Signed-off-by Alex Elder <elder@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
IPQ8074 has an integrated Hexagon dsp core q6v5 and a wireless lan
(Lithium) IP. An mdt type single image format is used for the
firmware. So the mdt_load function can be directly used to load
the firmware. Also add the relevant resets required for this core.
Acked-by: Rob Herring <robh@kernel.org> (bindings)
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
[bjorn: Rewrote as a separate driver, intead of extending q6v5_pil.c]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Migrate the MSS remoteproc driver to use the newly extracted helper
functions.
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Migrate the Hexagon V5 PAS (ADSP) driver to using the newly extracted
helper functions. The use of the handover callback does introduce latent
disabling of proxy resources. But apart from this there should be no
change in functionality.
Reviewed-by: Rohit kumar <rohitkr@codeaurora.org>
Reviewed-by: Sricharan R <sricharan@codeaurora.org>
Tested-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Shared between all Hexagon V5 based remoteprocs is the handling of the 5
interrupts and the SMP2P stop request, so break this out into a separate
function in order to allow these drivers to be cleaned up.
Reviewed-by: Rohit kumar <rohitkr@codeaurora.org>
Tested-by: Rohit kumar <rohitkr@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
With PHYS_ADDR_MAX there is now a type safe variant for all bits set.
Make use of it.
Patch created using a semantic patch as follows:
// <smpl>
@@
typedef phys_addr_t;
@@
-(phys_addr_t)ULLONG_MAX
+PHYS_ADDR_MAX
// </smpl>
Link: http://lkml.kernel.org/r/20180419214204.19322-1-stefan@agner.ch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add GLINK subdevice to allow definition of GLINK edge as a
child of modem-pil.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
From SDM845, the Q6SS reset sequence on software side has been
simplified with the introduction of boot FSM which assists in
bringing the Q6 out of reset.
SDM845 brings a new reset signal ALT_RESET which is a part of
the MSS subsystem hence requires reset clks to be enabled before
assert/deassert. Use the SoC specific reset helper function to
add support for ALT_RESET in SDM845.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Adding reset assert/deassert helper functions to handle SoC
specific reset sequences. This wil be used by SDM845 to assert and
deassert ALT_RESET and MSS_RESET signals.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce interrupt handler for smp2p ready interrupt to
handle start completion. Move the proxy votes for clocks
and regulators to the handover interrupt context.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
[bjorn: Only proxy unvote if handover irq has not fired]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
q6v5_request_irq() was supposed to return the irq number, but ret is
overwritten by the request_irq(), fix this and return the IRQ on
success.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Checkpatch recommends to use octal perms instead of S_IRUGO.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We're currently switching the platform to using the common clock
framework. We need to explicitly prepare and unprepare the rproc
clock.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Suman Anna <s-anna@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The davinci platform is being switched to using the common clock
framework, where clk_enable() can fail. Add the return value check.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Suman Anna <s-anna@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Remove dependencies on HAS_DMA where a Kconfig symbol depends on another
symbol that implies HAS_DMA, and, optionally, on "|| COMPILE_TEST".
In most cases this other symbol is an architecture or platform specific
symbol, or PCI.
Generic symbols and drivers without platform dependencies keep their
dependencies on HAS_DMA, to prevent compiling subsystems or drivers that
cannot work anyway.
This simplifies the dependencies, and allows to improve compile-testing.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add missing of_node_put()s at two places for device nodes returned by
of_parse_phandle().
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating
Hexagon v5")
Signed-off-by: Tobias Jordan <Tobias.Jordan@elektrobit.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix rproc_add_subdev parameter name and inverse the crashed logic.
Fixes: 880f5b3882 ("remoteproc: Pass type of shutdown to subdev remove")
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Any failure in the secure call for transferring mem ownership of mba
region to Q6 would result in reporting that the remoteproc device
is running. This is because the previous q6v5_clk_enable would have
been a success. Prevent this by updating variable 'ret' accordingly.
Cc: stable@vger.kernel.org
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently calling list_del on smd subdev remove path results in
null pointer dereference on glink only platforms. Fix this by
adding safety checks in glink/smd subdev remove paths.
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Access to the socket API and the root network namespace is only available
when networking is enabled:
ERROR: "kernel_sendmsg" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "sock_release" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "sock_create_kern" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "kernel_getsockname" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "init_net" [drivers/soc/qcom/qmi_helpers.ko] undefined!
ERROR: "kernel_recvmsg" [drivers/soc/qcom/qmi_helpers.ko] undefined!
Adding a dependency on CONFIG_NET lets us build it in all randconfig
builds.
Fixes: 9b8a11e826 ("soc: qcom: Introduce QMI encoder/decoder")
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We can return directly at the beginning of the function and save the 'err'
label.
We can also explicitly return 0 when the probe succeed.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Avoid some code ducplication and be more future-proof.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The sysmon client communicates either via a dedicated SMD/GLINK channel
or via QMI encoded messages over IPCROUTER with remote processors in
order to perform graceful shutdown and inform about other remote
processors shutting down.
Acked-By: Chris Lew <clew@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
remoteproc instances can be stopped either by invoking shutdown or by an
attempt to recover from a crash. For some subdev types it's expected to
clean up gracefully during a shutdown, but are unable to do so during a
crash - so pass this information to the subdev remove functions.
Acked-By: Chris Lew <clew@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Register MDT segments with the remoteproc core dump functionality in
order to include them in a core dump, in case of a recovery of the remote
processor.
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In order to implement support for grabbing core dumps in remoteproc it's
necessary to know the relocated base of the image, as the offsets from
the virtual memory base might not be based on the physical address.
Return the adjusted physical base address to the caller.
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The resource table is just one possible source of information that can
be extracted from the firmware file. Generalize this interface to allow
drivers to override this with parsers of other types of information.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As the remoteproc framework restarts the remote processor after a fatal
event, it's useful to be able to acquire a coredump of the remote
processor's state, for post mortem debugging.
This patch introduces a mechanism for extracting the memory contents
after the remote has stopped and before the restart sequence has begun
in the recovery path. The remoteproc framework builds the core dump in
memory and use devcoredump to expose this to user space.
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
[bjorn: Use vmalloc instead of composing the ELF on the fly]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
remoteproc is writing '\0' in the shared mem region. This
region is shared among multiple clients that are also trying
to read. Hence they miss first character.
Remove this null character write, as this mem area is
supposed to be Read only.
Further during every subsystem reboot, this region is
initialized with default, hence no need to write this
region.
Signed-off-by: Jitendra Sharma <shajit@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This contains a few bug fixes and a cleanup up of the resource-table handling
in the framework, which removes the need for drivers with no resource table to
provide a fake one.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=awTj
-----END PGP SIGNATURE-----
Merge tag 'rproc-v4.16' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This contains a few bug fixes and a cleanup up of the resource-table
handling in the framework, which removes the need for drivers with no
resource table to provide a fake one"
* tag 'rproc-v4.16' of git://github.com/andersson/remoteproc:
remoteproc: Reset table_ptr on stop
remoteproc: Drop dangling find_rsc_table dummies
remoteproc: Move resource table load logic to find
remoteproc: Don't handle empty resource table
remoteproc: Merge rproc_ops and rproc_fw_ops
remoteproc: Clone rproc_ops in rproc_alloc()
remoteproc: Cache resource table size
remoteproc: Remove depricated crash completion
virtio_remoteproc: correct put_device virtio_device.dev
The installed resource table is no longer accessible after stopping the
remote, so update table_ptr to point to the local copy.
Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As the core now deals with the lack of a resource table, remove the
dangling custom dummy implementations of find_rsc_table from drivers.
Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Extend the previous operation of finding the resource table in the ELF
with the extra step of populating the rproc struct with a copy and the
size. This allows drivers to override the mechanism used for acquiring
the resource table, or omit it for firmware that is known not to have a
resource table.
This leaves the custom, dummy, find_rsc_table implementations found in
some drivers dangling.
Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Allow a NULL table_ptr to have the same meaning as a table with 0
entries, allowing a subsequent patch to skip the assignment step.
A few other places in the implementation does dereference table_ptr, but
they are currently all coming from rproc_handle_resources().
Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
There are currently a few different schemes used for overriding fw_ops
or parts of fw_ops. Merge fw_ops into rproc_ops and expose the default
ELF-loader symbols so that they can be assigned by the drivers.
To keep backwards compatibility with the "default" case, a driver not
specifying the "load" operation is assumed to want the full ELF-loader
suit of functions.
Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In order to allow rproc_alloc() to, in a future patch, update entries in
the "ops" struct we need to make a local copy of it.
Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
We don't re-read the resource table during a recovery, so it is possible
in the recovery path that the resource table has a different size than
cached_table. Store the original size of cached_table to avoid these
getting out of sync.
Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The crash handling now happens in a single execution context, so there's
no longer a need for a completion to synchronize this.
Reviewed-By: Loic Pallardy <loic.pallardy@st.com>
Tested-By: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
rproc_virtio_dev_release will be called iff virtio_device.dev's
reference count drops to 0. Here we just put vdev.dev, and then
rproc->dev's cleanup will be done in rproc_virtio_dev_release.
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: weiping zhang <zhangweiping@didichuxing.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix ptr_ret.cocci warnings:
drivers/remoteproc/qcom_common.c:60:8-14: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds an interface for configuring Qualcomm's "secure SMMU" and adds
support for booting the modem Hexagon on MSM8996.
Two new debugfs entries are added in the remoteproc core to introspect the list
of memory carveouts and the loaded resource table.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lnNj
-----END PGP SIGNATURE-----
Merge tag 'rproc-v4.15' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This adds an interface for configuring Qualcomm's "secure SMMU" and
adds support for booting the modem Hexagon on MSM8996.
Two new debugfs entries are added in the remoteproc core to introspect
the list of memory carveouts and the loaded resource table"
* tag 'rproc-v4.15' of git://github.com/andersson/remoteproc:
remoteproc: qcom: Fix error handling paths in order to avoid memory leaks
remoteproc: qcom: Drop pr_err in q6v5_xfer_mem_ownership()
remoteproc: debug: add carveouts list dump feature
remoteproc: debug: add resource table dump feature
remoteproc: qcom: Add support for mss remoteproc on msm8996
remoteproc: qcom: Make secure world call for mem ownership switch
remoteproc: qcom: refactor mss fw image loading sequence
firmware: scm: Add new SCM call API for switching memory ownership
This turn RPMSG_VIRTIO into a user selectable config, fixes a few bugs in GLINK
and provides the support for specifying initial buffer sizes for GLINK
channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jirb
-----END PGP SIGNATURE-----
Merge tag 'rpmsg-v4.15' of git://github.com/andersson/remoteproc
Pull rpmsg updates from Bjorn Andersson:
- turn RPMSG_VIRTIO into a user selectable config
- fix few bugs in GLINK
- provide the support for specifying initial buffer sizes for GLINK
channels.
* tag 'rpmsg-v4.15' of git://github.com/andersson/remoteproc:
rpmsg: glink: The mbox client knows_txdone
rpmsg: glink: Add missing MODULE_LICENSE
rpmsg: glink: Use best fit intent during tx
rpmsg: glink: Add support to preallocate intents
dt-bindings: soc: qcom: Support GLINK intents
rpmsg: glink: Initialize the "intent_req_comp" completion variable
rpmsg: Allow RPMSG_VIRTIO to be enabled via menuconfig or defconfig
In case of error returned by 'q6v5_xfer_mem_ownership', we must free
some resources before returning.
In 'q6v5_mpss_init_image()', add a new label to undo a previous
'dma_alloc_attrs()'.
In 'q6v5_mpss_load()', re-use the already existing error handling code to
undo a previous 'request_firmware()', as already done in the other error
handling paths of the function.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The pr_err() in q6v5_xfer_mem_ownership() prints, upon failure, the
memory range that failed to be transitioned. But on 32-bit architectures
with CONFIG_PHYS_ADDR_T_64BIT set we cannot cast the phys_addr_t
variable to a pointer, per below build error. Instead these should be
formatted with %pap.
In file included from include/linux/kernel.h:14:0,
from include/linux/clk.h:16,
from drivers/remoteproc/qcom_q6v5_pil.c:18:
drivers/remoteproc/qcom_q6v5_pil.c: In function 'q6v5_xfer_mem_ownership':
drivers/remoteproc/qcom_q6v5_pil.c:337:10: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
(void *)addr, (void *)(addr + size),
^
Most callers will upon failure print a specific error message describing
which memory region that we failed to pass ownership of, so rather than
fixing the format string this patch fixes up the last callers and drop
the print from this function, saving us from spamming the log in most of
these error cases.
Fixes: 6c5a9dc248 ("remoteproc: qcom: Make secure world call for mem ownership switch")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch offers the capability to dump memory carveouts associated
to one remoteprocessor.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch adds the capability to display the content of
the resource table associated to a remote processor firmware.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add support for mss boot on msm8996. Major changes
include initializing mss rproc for msm8996, making appropriate
change for executing mss reset sequence etc.
Tested-and-acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
MSS proc on msm8996 can not access fw loaded region without stage
second translation of memory pages where mpss image are loaded.
This patch in order to enable mss boot on msm8996 invoke scm call
to switch or share ownership between apps and modem.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
[bjorn: Corrected error path in q6v5_start()]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch refactor code to first load all firmware blobs
and then update modem proc to authenticate and boot fw.
Tested-and-acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Currently, RPMSG_VIRTIO can only be enabled if some other kconfig
option selects it. This does not allow it to be enabled for
virtualized systems where Virtio RPMSG is available over Virtio
MMIO or PCI transport.
This patch updates RPMSG_VIRTIO kconfig option so that we can
enable the VirtIO RPMSG driver via menuconfig or defconfig. The
patch also removes "select RPMSG_VIRTIO" from various remoteproc
kconfig options because it is now user selectable.
Signed-off-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When RPMSG_QCOM_GLINK_SMEM=m and one driver causes the qcom_common.c file
to be compiled as built-in, we get a link error:
drivers/remoteproc/qcom_common.o: In function `glink_subdev_remove':
qcom_common.c:(.text+0x130): undefined reference to `qcom_glink_smem_unregister'
qcom_common.c:(.text+0x130): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `qcom_glink_smem_unregister'
drivers/remoteproc/qcom_common.o: In function `glink_subdev_probe':
qcom_common.c:(.text+0x160): undefined reference to `qcom_glink_smem_register'
qcom_common.c:(.text+0x160): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `qcom_glink_smem_register'
Out of the three PIL driver instances, QCOM_ADSP_PIL already has a
Kconfig dependency to prevent this from happening, but the other two
do not. This adds the same dependency there.
Fixes: eea07023e6 ("remoteproc: qcom: adsp: Allow defining GLINK edge")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The priv->mem[] array has IMX7D_RPROC_MEM_MAX elements so the > should
be >= to avoid writing one element beyond the end of the array.
Fixes: a0ff4aa6f0 ("remoteproc: imx_rproc: add a NXP/Freescale imx_rproc driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This extends the Qualcomm GLINK implementation to support the additional
features used for communicating with modem and DSP coprocessors in modern
Qualcomm platforms.
In addition to this there's support for placing virtio RPMSG buffers in
non-System RAM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PVGN
-----END PGP SIGNATURE-----
Merge tag 'rpmsg-v4.14' of git://github.com/andersson/remoteproc
Pull rpmsg updates from Bjorn Andersson:
"This extends the Qualcomm GLINK implementation to support the
additional features used for communicating with modem and DSP
coprocessors in modern Qualcomm platforms.
In addition to this there's support for placing virtio RPMSG buffers
in non-System RAM"
* tag 'rpmsg-v4.14' of git://github.com/andersson/remoteproc: (29 commits)
rpmsg: glink: initialize ret to zero to ensure error status check is correct
rpmsg: glink: fix null pointer dereference on a null intent
dt-bindings: soc: qcom: Extend GLINK to cover SMEM
remoteproc: qcom: adsp: Allow defining GLINK edge
rpmsg: glink: Export symbols from common code
rpmsg: glink: Release idr lock before returning on error
rpmsg: glink: Handle remote rx done command
rpmsg: glink: Request for intents when unavailable
rpmsg: glink: Use the intents passed by remote
rpmsg: glink: Receive and store the remote intent buffers
rpmsg: glink: Add announce_create ops and preallocate intents
rpmsg: glink: Add rx done command
rpmsg: glink: Make RX FIFO peak accessor to take an offset
rpmsg: glink: Use the local intents when receiving data
rpmsg: glink: Add support for TX intents
rpmsg: glink: Fix idr_lock from mutex to spinlock
rpmsg: glink: Add support for transport version negotiation
rpmsg: glink: Introduce glink smem based transport
rpmsg: glink: Do a mbox_free_channel in remove
rpmsg: glink: Return -EAGAIN when there is no FIFO space
...
In certain circumstances rpmsg devices needs to acquire a handle to the
ancestor remoteproc instance, e.g. to invoke rproc_report_crash() when a
fatal error is detected. Introduce an interface that walks the device
tree in search for a remoteproc instance and return this.
Tested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The ssr_notifiers variable should be local, so add the missing static
storage classifier.
Fixes: 1e140df049 ("remoteproc: qcom: Add support for SSR notifications")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Introduce the GLINK subdev, which allows the definition of a GLINK edge
as child of a remoteproc.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Subdevices might depend on earlier registered subdevices for
communication purposes, as such they should be stopped in reverse order
so that said communication channel is removed after the dependent
subdevice is stopped.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Provide a basic driver to control Cortex M4 co-processor found
on NXP i.MX7D and i.MX6SX.
Currently it is able to resolve addresses between M4 and main CPU,
start and stop the co-processor. Other functionality is not provided
or test.
This driver was tested on NXP i.MX7D and expected to work on
i.MX6SX as well.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-remoteproc@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-remoteproc@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: linux-remoteproc@vger.kernel.org
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add support to the keystone remoteproc driver for managing the
DSP present in the Keystone 2 66AK2G SoC. The 66AK2G SoC has
a Power Management Micro Controller (PMMC) that manages the
individual device's power, clock and reset functionalities.
The keystone remoteproc driver already uses standard frameworks
for reset and clock control, so it doesn't require any significant
modifications other than a new compatible suitable for 66AK2G DSP.
The binding document is also updated to reflect the modified
property values used by the 66AK2G DSP node as compared to the
values used by existing Keystone 2 DSPs.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Davinci remoteproc driver currently supports the DSP remoteproc
device created in legacy-style on OMAP-L13x SoCs. The driver has been
enhanced to support the DSP remoteproc device created through Device
Tree now. The current DT support handles the C674x DSP processor
subsystem on OMAP-L138 SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The DSP subsystem on OMAP-L13x SoCs has various internal RAM
memories that can accessed from the ARM side. These memories
can be configured to be used as either RAM or Cache.
The Davinci remoteproc driver has been enhanced to parse and
store the kernel mappings for these internal RAM memories.
These mappings can then be used to support direct loading of
text/data into these memories from the remoteproc driver.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The davinci remoteproc driver currently uses the platform_get_resource()
API for retrieving the IOMEM resources. Switch this function to use the
platform_get_resource_byname() API instead in preparation for adding the
DT support so that the binding can be agnostic of the IOMEM resource
order.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Make this const as it is only stored in the type field of a device
structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This adds the remoteproc part of subsystem restart, which is responsible
for emitting notifications to other processors in the system about a
dying remoteproc instance.
These notifications are propagated to the various communication systems
in the various remote processors to shut down communication links that
was left in a dangling state as the remoteproc was stopped (or crashed).
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The additional arguments in the internal __rproc_boot() function
were dropped in commit 2bfc311a57 ("remoteproc: Drop wait in
__rproc_boot()"). The exported rproc_boot() is now just a wrapper
around this internal function, so merge them together.
While at this, also remove the declaration for the previously
cleaned up rproc_boot_nowait() function.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Drop the dependency on RESET_CONTROLLER for the Keystone remoteproc
driver to resolve some circular dependencies around different choices
for RESET_CONTROLLER on common ARM configs. This dependency is
inherent as the RESET_CONTROLLER will be enabled due to the enabled
ARCH_HAS_RESET_CONTROLLER for ARCH_KEYSTONE.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
All the remoteproc platform driver Kconfig symbols are defined and
included under an if REMOTEPROC condition, so the dependency on
REMOTEPROC is implicit and they do not need an explicit 'depends
on REMOTEPROC' line. So, clean these up.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A dependency to VIRTUALIZATION has been added to REMOTEPROC in v3.10
kernel in commit b9777859ec ("remoteproc: fix kconfig dependencies
for VIRTIO") to resolve Kconfig warnings due to the inclusion of the
virtio configuration file from the ARM's KVM config file. The KVM
config was fixed properly in the subsequent release in commit
8bd4ffd6b3 ("ARM: kvm: don't include drivers/virtio/Kconfig").
So, drop this unneeded VIRTUALIZATION dependency from REMOTEPROC.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The DSPs are expected to be in reset when the driver probes a device.
If the DSPs are out of reset in probe, the system may crash when the
firmware is being loaded. So, add a check to make sure the DSP resets
are asserted, and if not, throw a eye-catchy warning and assert the
resets specifically.
Signed-off-by: Andrew F. Davis <afd@ti.com>
[s-anna@ti.com: replace warning with a WARN]
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Texas Instrument's Keystone 2 family of SoCs has 1 or more
TMS320C66x DSP Core Subsystems (C66x CorePacs). Each subsystem has
a C66x Fixed/Floating-Point DSP Core, with 32KB of L1P and L1D SRAMs,
that can be configured and partitioned as either RAM and/or Cache,
and 1 MB of L2 SRAM. The CorePac also includes an Internal DMA (IDMA),
External Memory Controller (EMC), Extended Memory Controller (XMC)
with a Memory Protection and Address Extension (MPAX) unit, a Bandwidth
Management (BWM) unit, an Interrupt Controller (INTC) and a Powerdown
Controller (PDC).
A new remoteproc module is added to perform the device management of
these DSP devices. The driver expects the firmware names to be of the
form "keystone-dsp<X>-fw", where X is the corresponding DSP number, and
uses the standard remoteproc core ELF loader. The support is limited
to images only using the DSP internal memories at the moment. This
remoteproc driver is also designed to work with virtio, and uses the
IPC Generation registers for performing the virtio signalling and
getting notified of exceptions.
The driver currently supports the 66AK2H/66AK2K, 66AK2L and 66AK2E
SoCs.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Sam Nelson <sam.nelson@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The davinci remoteproc driver is currently de-asserting the reset in
its rproc .start() ops, but is not asserting the reset in its .stop()
ops. This leaves the remote processor to not boot properly when using
the sysfs 'state' variable between multiple start and stop operations.
On the other hand, a reset is being asserted unconditionally in the
driver remove function to alleviate some of these issues.
Move this reset assertion logic into the .stop() ops implementation
to fix the sysfs state-machine and the unbalanced reset. The logic
from remove is still effective since .stop() ops will be invoked
during the remove due to the enabled 'auto-boot' support. The probe
already has support for asserting the reset in case the DSP is not
in reset for some reason.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The reset_assert() function is used to make sure the DSP remote
processor is in a reset state regardless of its previous state.
The driver relies on davinci_clk_reset_{assert,deassert}()
functions for reset management which take in a clock parameter.
The assert_reset() performs a clk_get()/clk_put() cycle to
acquire the clock handle to use with this function. This is
totally unnecessary and the code can be simplified to use
the clock acquired during probe and directly use the reset
functions, so simplify this logic.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The davinci remoteproc driver requires a CMA pool for allocating
memory for virtio vrings/buffers and other sections of the firmware
image. The allocations are done using the DMA API. The CMA option is
currently selected automatically on systems with MMU when davinci
remoteproc is enabled, switch this to a saner depends on dependency
convention. The dependency is also updated to use the DMA_CMA kconfig
symbol that is used for CMA allocations using the DMA API, the CMA
dependency is inherited implicitly.
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Replace rproc_shutdown() by rproc_stop() and rproc_boot() by
rproc_start() in the recovery path, in order to avoid remoteproc
resources re-allocation overhead and to assist with extracting the
coredumps after stopping the remote processor.
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In the context of recovering from crash, rproc_trigger_recovery() does
rproc_shutdown() followed by rproc_boot(). The remoteproc resources are
cleaned up in rproc_shutdown() and immediately reallocated in
rproc_boot() which is an unnecessary overhead. Furthermore, we want the
memory regions to be accessible after stopping the remote processor, to
be able to extract the memory content for a coredump.
This patch factors out the code in rproc_boot() and rproc_shutdown()
path and introduces rproc_{start,stop}() in order to avoid resource
allocation overhead.
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A bunch of changes to virtio, most affecting virtio net.
ptr_ring batched zeroing - first of batching enhancements
that seems ready.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZEceWAAoJECgfDbjSjVRpg8YIAIbB1UJZkrHh/fdCQjM2O53T
ESS62W91LBT+weYH/N79RrfnGWzDOHrCQ8Or1nAKQZx2vU1aroqYXeJ9o0liRBYr
hGZB1/bg8obA5XkKUfME2+XClakvuXABUJbky08iDL9nILlrvIVLoUgZ9ouL0vTj
oUv4n6jtguNFV7tk/injGNRparEVdcefX0dbPxXomx5tSeD2fOE96/Q4q2eD3f7r
NHD4DailEJC7ndJGa6b4M9g8shkXzgEnSw+OJHpcJcxCnAzkVT94vsU7OluiDvmG
bfdGZNb0ohDYZLbJDR8aiMkoad8bIVLyGlhqnMBiZQEOF4oiWM9UJLvp5Lq9g7A=
=Sb7L
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"Fixes, cleanups, performance
A bunch of changes to virtio, most affecting virtio net. Also ptr_ring
batched zeroing - first of batching enhancements that seems ready."
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
s390/virtio: change maintainership
tools/virtio: fix spelling mistake: "wakeus" -> "wakeups"
virtio_net: tidy a couple debug statements
ptr_ring: support testing different batching sizes
ringtest: support test specific parameters
ptr_ring: batch ring zeroing
virtio: virtio_driver doc
virtio_net: don't reset twice on XDP on/off
virtio_net: fix support for small rings
virtio_net: reduce alignment for buffers
virtio_net: rework mergeable buffer handling
virtio_net: allow specifying context for rx
virtio: allow extra context per descriptor
tools/virtio: fix build breakage
virtio: add context flag to find vqs
virtio: wrap find_vqs
ringtest: fix an assert statement
Allows maintaining extra context per vq. For ease of use, passing in
NULL is legal and disables the feature for all vqs.
Includes fixes by Christian for s390, acked by Cornelia.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Remove the standalone SMD implementation as we have transitioned the
client drivers to use the RPMSG based one.
Also remove all dependencies on QCOM_SMD from Kconfig files, in order to
keep them selectable in the absence of the removed symbol.
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
qcom_smd_register_edge() is provided by either QCOM_SMD or RPMSG_QCOM_SMD,
and if both of them are disabled, it does nothing.
The check for the PIL drivers however only checks for QCOM_SMD, so it breaks
with QCOM_SMD=n && RPMSG_QCOM_SMD=m:
drivers/remoteproc/built-in.o: In function `smd_subdev_remove':
qcom_wcnss_iris.c:(.text+0x231c): undefined reference to `qcom_smd_unregister_edge'
drivers/remoteproc/built-in.o: In function `smd_subdev_probe':
qcom_wcnss_iris.c:(.text+0x2344): undefined reference to `qcom_smd_register_edge'
drivers/remoteproc/built-in.o: In function `smd_subdev_probe':
qcom_q6v5_pil.c:(.text+0x3538): undefined reference to `qcom_smd_register_edge'
qcom_q6v5_pil.c:(.text+0x3538): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `qcom_smd_register_edge'
This clarifies the Kconfig dependency.
Fixes: 4b48921a8f ("remoteproc: qcom: Use common SMD edge handler")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Looks like a quiet cycle for vhost/virtio, just a couple of minor
tweaks. Most notable is automatic interrupt affinity for blk and scsi.
Hopefully other devices are not far behind.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYt1rRAAoJECgfDbjSjVRpEZsIALSHevdXWtRHBZUb0ZkqPLQb
/x2Vn49CcALS1p7iSuP9L027MPeaLKyr0NBT9hptBChp/4b9lnZWyyAo6vYQrzfx
Ia/hLBYsK4ml6lEwbyfLwqkF2cmYCrZhBSVAILifn84lTPoN7CT0PlYDfA+OCaNR
geo75qF8KR+AUO0aqchwMRL3RV3OxZKxQr2AR6LttCuhiBgnV3Xqxffg/M3x6ONM
0ffFFdodm6slem3hIEiGUMwKj4NKQhcOleV+y0fVBzWfLQG9210pZbQyRBRikIL0
7IsaarpaUr7OrLAZFMGF6nJnyRAaRrt6WknTHZkyvyggrePrGcmGgPm4jrODwY4=
=2zwv
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull vhost updates from Michael Tsirkin:
"virtio, vhost: optimizations, fixes
Looks like a quiet cycle for vhost/virtio, just a couple of minor
tweaks. Most notable is automatic interrupt affinity for blk and scsi.
Hopefully other devices are not far behind"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio-console: avoid DMA from stack
vhost: introduce O(1) vq metadata cache
virtio_scsi: use virtio IRQ affinity
virtio_blk: use virtio IRQ affinity
blk-mq: provide a default queue mapping for virtio device
virtio: provide a method to get the IRQ affinity mask for a virtqueue
virtio: allow drivers to request IRQ affinity when creating VQs
virtio_pci: simplify MSI-X setup
virtio_pci: don't duplicate the msix_enable flag in struct pci_dev
virtio_pci: use shared interrupts for virtqueues
virtio_pci: remove struct virtio_pci_vq_info
vhost: try avoiding avail index access when getting descriptor
virtio_mmio: expose header to userspace
Add a struct irq_affinity pointer to the find_vqs methods, which if set
is used to tell the PCI layer to create the MSI-X vectors for our I/O
virtqueues with the proper affinity from the start. Compared to after
the fact affinity hints this gives us an instantly working setup and
allows to allocate the irq descritors node-local and avoid interconnect
traffic. Last but not least this will allow blk-mq queues are created
based on the interrupt affinity for storage drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
In the transition from using rproc_da_to_va(), the type of the load
offset became unsigned. This causes the subsequent check to let negative
values less than p_memsz + mem_size through and we write outside of the
buffer.
Change the type back to a signed value to catch this.
Fixes: 7f0dd07a9b ("remoteproc: qcom: mdt_loader: Refactor MDT loader")
Fixes: e7fd252262 ("remoteproc: qcom: q6v5: Decouple driver from MDT loader")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch provides virtio communication support based on mailbox
for ST co-processors.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Associated clock is prepared in st_rproc_parse_dt function.
it should be unprepared in case of error during probing.
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The functions rproc_add_virtio_devices() and rproc_fw_config_virtio()
are reduced to trigger auto-boot only. Modify these function names and
related comments to reflect their current state.
This patch does not add any functional change.
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The rproc_add_virtio_devices() requests firmware asynchronously and
triggers boot if the auto_boot flag is set. However, this
asynchronous call seems to be redundant for non auto-boot scenario
since the rproc_boot() would call request_firmware() anyways. Move
the auto_boot check to rproc_add() so that a redundant call to
_request_firmware can be avoided for non auto-boot case.
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
SCM call to check whether Peripheral Authentication Service (PAS) is
supported returns false for ADSP on MSM8996. Drop this call from the
driver so that the probe() function succeeds for ADSP PIL device.
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Call the common SMD edge handler to instantiate subdevices to bring
associated SMD edges up and down as the remoteproc is started and
stopped.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Move the SMD edge handling to the Qualcomm common file to make it
reusable for other Qualcomm remoteproc drivers.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
With the remoteproc parts cleaned out of the MDT loader we can move it
to drivers/soc/qcom.
Acked-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Pushing the SCM calls into the MDT loader reduces duplication in the
callers and allows for non-remoteproc clients to use the helper for
parsing and loading MDT files.
Cc: Andy Gross <andy.gross@linaro.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The "fw" firmware object is passed from the remoteproc core and should
not be overwritten, as that results in leaked buffers and a double free
of the the last firmware object.
Fixes: 051fb70fd4 ("remoteproc: qcom: Driver for the self-authenticating Hexagon v5")
Cc: stable@vger.kernel.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In preparation for moving the mdt loader out of remoteproc let's move
the somewhat unrelated resource table dummy helper to a Qualcomm
"common" file.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Rather than duplicating half of the MDT loader in the validation step
move the entire MDT parser into the q6v5 driver. This allows us to make
the shared MDT-loader call the SCM PAS operations directly which
simplifies the client code and allows for better reuse of the code.
Cc: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Q6V5 in MSM8916 doesn't have a mss supply, so remove this and update
the code to support cases without proxy or active supplies.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The recently added initialization is rather unusual because it uses a constructor for
a variable-length array to assign a constant structure to a member that uses a fixed-length
array. This confuses clang and breaks the build.
drivers/remoteproc/qcom_q6v5_pil.c:1024:18: error: incompatible pointer types initializing 'const char *' with an expression of type
:%s 'struct qcom_mss_reg_res [4]' [-Werror,-Wincompatible-pointer-types]
.proxy_supply = (struct qcom_mss_reg_res[]) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/remoteproc/qcom_q6v5_pil.c:1024:18: warning: suggest braces around initialization of subobject [-Wmissing-braces]
.proxy_supply = (struct qcom_mss_reg_res[]) {
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
We can either turn this constructor into a regular initializer by removing
the 'struct qcom_mss_reg_res[])', or we can make the array variable length.
The latter approach is used for the arrays of strings in the same structure,
so let's use that here too.
Fixes: 19f902b53b ("remoteproc: qcom: Initialize and enable proxy and active regulators.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
firmware_loading_complete is used to synchronize operations
on rproc while asynchronous firmware loading is in progress.
However, rproc_boot() no longer waits on
firmware_loading_complete. Hence drop this completion
variable altogether and handle the race between rproc_del()
and rproc_boot() using new state RPROC_DELETED.
The request_firmware_nowait() will hold the reference to
rproc device by using a get_device()/put_device(), so the
rproc struct will remain valid even when we return from
rproc_del() before the asynchronous call to
rproc_fw_config_virtio() completes.
CC: Loic Pallardy <loic.pallardy@st.com>
CC: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add new state RPROC_DELETED to handle synchronization
between rproc_del() and other operations on rproc. This
state represents the rproc device that has been "deleted".
CC: Loic Pallardy <loic.pallardy@st.com>
CC: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The "remoteproc{0,1...}" sysfs entries are added in
rproc_add() and deleted in rproc_type_release() instead of
in rproc_del(). That leaves these lingering entries sticking
around after we return from rproc_del(). Move the
rproc_delete_debug_dir() to rproc_del() to fix this.
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch add additional clock and regulator resource which are
initialized based on compatible and has no impact on existing driver
working. This resourse addition enable the existing driver to handle.
low pass sensor processor device also.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This patch initialize certain driver related data based on compatible
string. This enable driver to handle more than one similar device in
by differentiating in probe their private data.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Declare rproc_ops structures as const as they are only passed as an
argument to the function rproc_alloc. This argument is of type const, so
rproc_ops structures having this property can be declared const too.
Done using Coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct rproc_ops i@p = {...};
@ok1@
identifier r1.i;
position p;
@@
rproc_alloc(...,&i@p,...)
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct rproc_ops i;
File size details:
Size of the file remoteproc/da8xx_remoteproc.o remains the same before and
after applying the changes.
text data bss dec hex filename
1312 100 4 1416 588 remoteproc/da8xx_remoteproc.o
1312 100 4 1416 588 remoteproc/da8xx_remoteproc.o
970 240 0 1210 4ba remoteproc/omap_remoteproc.o
1002 192 0 1194 4aa remoteproc/omap_remoteproc.o
1901 240 0 2141 85d remoteproc/st_remoteproc.o
1933 192 0 2125 84d remoteproc/st_remoteproc.o
1288 96 0 1384 568 remoteproc/st_slim_rproc.o
1320 64 0 1384 568 remoteproc/st_slim_rproc.o
2121 240 0 2361 939 remoteproc/wkup_m3_rproc.o
2161 192 0 2353 931 remoteproc/wkup_m3_rproc.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Certain regulators need voting by rproc on behalf of hexagon only during
restart operation but certain regulator need to be voted till hexagon
is up, these regulators are identified as proxy and active regulators
respectively. This patch provide interface to initialize, enable and
disable proxy and active regulators separately.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
[bjorn: dropped disable of proxy regulators from stop]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Certain clocks need voting by rproc on behalf of hexagon only during
restart operation but certain clocks need to be voted till hexagon is
up, these clocks are identified as proxy and active clocks respectively.
This patch provide interface to initialize, enable and disable proxy and
active clocks separately.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
[bjorn: dropped disable of proxy clocks on stop]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
MSS rproc loader need chip specific resources initialization during probe
to load and boot modem firmware, this need compatible string based
differentiation in resources to be initialized. This patch add and provide
a template struct whose fields represent all those resources which are
needed to load and boot modem fw and which may differ from chip to chip.
This patch also add new compatible string for msm8916, msm8974 platform.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Top level config option without any kind of help... is kind of
strange. Remote processors could also mean some kind of distributed
computing...
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Following any fw_rsc_vdev entries in the resource table are two variable
length arrays, the first one reference vring resources and the second
one is the virtio config space. The virtio config space is used by
virtio to communicate status and configuration changes and must as such
be shared with the remote.
The reverted commit incorrectly made any changes to the virtio config
space only affect the local copy, in an attempt to allowing memory
protection of the shared resource table.
This reverts commit cda8529346.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Commit 2b45cef586 ("remoteproc: Further extend the vdev life cycle")
extends kref support for vdev management.
It introduces a regression when following sequence is executed:
rproc_boot --> rproc_shutdown --> rproc_boot
Second rproc_boot call crashes on register_virtio_device as device
is already existing.
Issue is previous vdev is never released when rproc is stop because
associated refcount is too high.
kref_get introduces is not needed as kref_init already initializes
krefcount to 1 because it considers associated variable as used.
This introduces a misalignment between kref_get and kref_put calls.
Fixes: 2b45cef586 ("remoteproc: Further extend the vdev life cycle")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The adsp-pil driver relies on SCM and causes a build error without it:
ERROR: "qcom_scm_pas_supported" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_scm_is_available" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_scm_pas_auth_and_reset" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_scm_pas_shutdown" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_scm_pas_mem_setup" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_scm_pas_init_image" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
This adds a 'select', as SCM is a silent Kconfig symbol that gets
enabled implicitly by all its users.
Fixes: b9e718e950 ("remoteproc: Introduce Qualcomm ADSP PIL")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
In the event that rproc_boot() is called before the firmware loaded
completion has been flagged it will wait with the mutex held,
obstructing the request_firmware_nowait() callback from completing the
wait.
As rproc_fw_config_virtio() has been reduced to only triggering
auto-boot there is no longer a reason for waiting in rproc_boot(), so
drop this.
Cc: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Back in July 2014 I asked around what was the intended target
platform for the STE Modem remoteproc driver, so that I could add the
proper hardware dependency to its config option. The answer I got was
that there was no known publicly available hardware needing it and it
was unlikely that there ever would.
So I think it's time to delete this driver to lower the maintenance
burden.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Suman Anna <s-anna@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Warning users that remoteproc and it's binary format are under
development doesn't serve much of a purpose. Different drivers support
different image formats and the resource table has a version field that
would need to be bumped when incompatible changes are introduced.
So lets drop this warning to clean up the kernel log.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The adsp-pil driver relies on SCM and causes a build error without it:
ERROR: "qcom_scm_pas_supported" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_scm_is_available" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_scm_pas_auth_and_reset" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_scm_pas_shutdown" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_scm_pas_mem_setup" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
ERROR: "qcom_scm_pas_init_image" [drivers/remoteproc/qcom_adsp_pil.ko] undefined!
This adds a 'select', as SCM is a silent Kconfig symbol that gets
enabled implicitly by all its users.
Fixes: b9e718e950 ("remoteproc: Introduce Qualcomm ADSP PIL")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add linux/sizes.h to prevent build failure on non ARM architectures
as:
CC [M] drivers/remoteproc/qcom_mdt_loader.o
In file included from include/linux/cache.h:4:0,
from include/linux/printk.h:8,
from include/linux/kernel.h:13,
from include/asm-generic/bug.h:13,
from arch/x86/include/asm/bug.h:35,
from include/linux/bug.h:4,
from include/linux/thread_info.h:11,
from arch/x86/include/asm/elf.h:7,
from include/linux/elf.h:4,
from drivers/remoteproc/qcom_mdt_loader.c:18:
drivers/remoteproc/qcom_mdt_loader.c: In function ‘qcom_mdt_parse’:
drivers/remoteproc/qcom_mdt_loader.c:90:52: error: ‘SZ_4K’ undeclared
(first use in this function)
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The transition from rproc_put to rproc_free raced with the review of the
Qualcomm ADSP and ST SLIMproc drivers and these where not updated
accordingly.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
When qcom_smd is a loadable module and wcnss-pil is built-in,
we get a link error:
drivers/remoteproc/qcom_wcnss_pil.o: In function `wcnss_smd_remove':
qcom_wcnss_iris.c:(.text.wcnss_smd_remove+0x10): undefined reference to `qcom_smd_unregister_edge'
drivers/remoteproc/qcom_wcnss_pil.o: In function `wcnss_smd_probe':
qcom_wcnss_iris.c:(.text.wcnss_smd_probe+0x12): undefined reference to `qcom_smd_register_edge'
This adds a Kconfig dependency to avoid this. We can still allow
build-testing with SMD disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Add xo clock support required to boot up Qualcomm ADSP processor.
The ADSP remoteproc driver keeps xo clock enabled until the
driver receives "handover" irq, in order to allow ADSP processor
to vote for xo clock with rpm.
Signed-off-by: Sarangdhar Joshi <spjoshi@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The newly added driver tries to 'select' a symbol that it has an
implicit dependency on, which confuses Kconfig:
subsection "Kconfig recursive dependency limitations"
drivers/remoteproc/Kconfig:3: symbol REMOTEPROC is selected by QCOM_ADSP_PIL
As REMOTEPROC is itself user-visible, we clearly should not select
it from a driver, removing the line fixes the problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The Qualcomm ADSP Peripheral Image Loader is used on a variety of
different Qualcomm platforms for loading firmware into and controlling
the Hexagon based ADSP.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The tie between the main WCNSS driver and the IRIS driver causes a
circular dependency between the two modules. Neither part makes sense to
have on their own so lets merge them into one module.
For the sake of picking up the clock and regulator resources described
in the iris of_node we need an associated struct device. But, to keep
the size of the patch down we continue to represent the IRIS part as its
own platform_driver, within the same module, rather than setting up a
dummy device.
Fixes: aed361adca ("remoteproc: qcom: Introduce WCNSS peripheral image loader")
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
As all vdev resources are allocated before we boot the remote processor
we no longer need to support modifying the resource table while the
remote is running.
This saves us from the table_ptr dance, but more importantly allow the
remote processor to enable security lock down of the loaded table memory
region.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The vdev handler is now just another resource allocator, so handle all
resource types in a single pass.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Vrings are now allocated as we parse the resource table, before we
boot the rproc or register any virtio devices, so it's safe to bump
max_notifyid as part of this process.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Represent the virtio device part of the vdev resources as remoteproc
subdevices to finalize the decoupling of the virtio resource and device
handling.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tie the vdev (and hence vring) life cycle to the resource parsing and
resource cleanup operations, allowing us to safely register and
unregister virtio devices on the go.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Instead of having the vrings being allocated and freed as they are
requested by the virtio device tie their life cycle to the vdev
resource. This allows us to decouple the vdev resource management from
the virtio device management.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Allow the wcnss smd edge to be described as a child of the wcnss
remoteproc node and make the edge life cycle follow the running state of
the remoteproc.
This bond is necessary to clean up the smd state when the remote
processor is suddenly removed, and in some cases even when it shut down
in a controlled fasion.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
A subdevice is an abstract entity that can be used to tie actions to the
booting and shutting down of a remote processor. The subdevice object is
expected to be embedded in concrete implementations, allowing for a
variety of use cases to be implemented.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix to return a negative error code from the st_rproc_state() error
handling case instead of 0, as done elsewhere in this function.
Fixes: 63edb0310a ("remoteproc: Supply controller driver for ST's Remote Processors")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Since there is now an always available state file in sysfs with the same
function as this one in debugfs, remove the redundant entry.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Suman Anna