Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer;
also offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types
-----BEGIN PGP SIGNATURE-----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=eTIC
-----END PGP SIGNATURE-----
Merge tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It's been busy summer weeks and hence lots of changes, partly for a
few new drivers and partly for a wide range of fixes.
Here are highlights:
ALSA Core:
- Fix rawmidi buffer management, code cleanup / refactoring
- Fix the SG-buffer page handling with incorrect fallback size
- Fix the stall at virmidi trigger callback with a large buffer; also
offloading and code-refactoring along with it
- Various ALSA sequencer code cleanups
ASoC:
- Deploy the standard snd_pcm_stop_xrun() helper in several drivers
- Support for providing name prefixes to generic component nodes
- Quite a few fixes for DPCM as it gains a bit wider use and more
robust testing
- Generalization of the DIO2125 support to a simple amplifier driver
- Accessory detection support for the audio graph card
- DT support for PXA AC'97 devices
- Quirks for a number of new x86 systems
- Support for AM Logic Meson, Everest ES7154, Intel systems with
RT5682, Qualcomm QDSP6 and WCD9335, Realtek RT5682 and TI TAS5707
HD-audio:
- Code refactoring in HD-audio ext codec codes to drop own classes;
preliminary works for the upcoming legacy codec support
- Generalized DRM audio component for the upcoming radeon / amdgpu
support
- Unification of mic mute-LED and GPIO support for various codecs
- Further improvement of CA0132 codec support including Recon3D
- Proper vga_switcheroo handling for AMD i-GPU
- Update of model list in documentation
- Fixups for another HP Spectre x360, Conexant codecs, power-save
blacklist update
USB-audio:
- Fix the invalid sample rate setup with external clock
- Support of UAC3 selector units and processing units
- Basic UAC3 power-domain support
- Support for Encore mDSD and Thesycon-based DSD devices
- Preparation for future complete callback changes
Firewire:
- Add support for MOTU Traveler
Misc:
- The endianess notation fixes in various drivers
- Add fall-through comment in lots of drivers
- Various sparse warning fixes, e.g. about PCM format types"
* tag 'sound-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (529 commits)
ASoC: adav80x: mark expected switch fall-through
ASoC: da7219: Add delays to capture path to remove DC offset noise
ALSA: usb-audio: Mark expected switch fall-through
ALSA: mixart: Mark expected switch fall-through
ALSA: opl3: Mark expected switch fall-through
ALSA: hda/ca0132 - Add exit commands for Recon3D
ALSA: hda/ca0132 - Change mixer controls for Recon3D
ALSA: hda/ca0132 - Add Recon3D input and output select commands
ALSA: hda/ca0132 - Add DSP setup defaults for Recon3D
ALSA: hda/ca0132 - Add Recon3D startup functions and setup
ALSA: hda/ca0132 - Add bool variable to enable/disable pci region2 mmio
ALSA: hda/ca0132 - Add Recon3D pincfg
ALSA: hda/ca0132 - Add quirk ID and enum for Recon3D
ALSA: hda/ca0132 - Add alt_functions unsolicited response
ALSA: hda/ca0132 - Clean up ca0132_init function.
ALSA: hda/ca0132 - Create mmio gpio function to make code clearer
ASoC: wm_adsp: Make DSP name configurable by codec driver
ASoC: wm_adsp: Declare firmware controls from codec driver
ASoC: max98373: Added software reset register to readable registers
ASoC: wm_adsp: Correct DSP pointer for preloader control
...
The driver uses genalloc functions. Select GENERIC_ALLOCATOR to prevent
build errors when selected through COMPILE_TEST.
Fixes: 88a40e7dca ("mtd: rawnand: atmel: Allow selection of this driver when COMPILE_TEST=y")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Now that it is possible to do dynamic allocations during the
identification phase, convert the onfi_params structure (which is only
needed with ONFI compliant chips) into a pointer that will be allocated
only if needed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Thanks to the migration of all drivers to use nand_scan() and the
related nand_controller_ops, we can now allocate data during the
detection phase. Let's do it first for the NAND model parameter which
is allocated in nand_detect().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Both nand_scan_ident() and nand_scan_tail() helpers used to be called
directly from controller drivers that needed to tweak some ECC-related
parameters before nand_scan_tail(). This separation prevented dynamic
allocations during the phase of NAND identification, which was
inconvenient.
All controller drivers have been moved to use nand_scan(), in
conjunction with the chip->ecc.[attach|detach]_chip() hooks that
actually do the required tweaking sequence between both ident/tail
calls, allowing programmers to use dynamic allocation as they need all
across the scanning sequence.
Declare nand_scan_[ident|tail]() statically now.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
A comment in the probe declares that values are assigned to ecc.size
and ecc.bytes, but these values will be overwritten. This is not
entirely right as they are overwritten only if
mtd->writesize >= 512. Let's clarify this by moving these assignations
to txx9ndfmc_nand_scan().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prepare the migration to nand_scan() by moving both calls to
nand_scan_ident() and nand_scan_tail() in a single spot.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
An error after nand_scan_tail() should trigger a nand_cleanup(), not a
nand_release() as mtd_device_register() (or one of its variants) has not
been called and there is no need to deregister any MTD device yet.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Some driver (eg. docg4) will need to handle themselves the
identification phase. As part of the migration to use nand_scan()
everywhere (which will unconditionnaly call nand_scan_ident()), we add
a condition at the start of nand_scan_with_ids() to jump over
nand_scan_ident() if the maxchips parameters is zero, meaning that the
driver does not want the core to handle this phase.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
No need for an atmel_nand_register() function, let's move the code in
it directly where the function was called: in
atmel_nand_controller_add_nand(). To make things consistent, also
rename atmel_nand_unregister() into
atmel_nand_controller_remove_nand().
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan_with_ids() (alternative to nand_scan() for passing
a flash IDs table) instead of the nand_scan_ident() + nand_scan_tail()
pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
nand_cleanup() should be called upon error after a successful
nand_scan_tail().
Rework the error path to follow this rule .
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
As already done in the core, calling a struct nand_controller
'hw_control' is misleading. Use the same name as in nand_base.c:
'controller'.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Xiaolei Li <xiaolei.li@mediatek.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Harvey Hunt <harveyhuntnexus@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Notes:
"pw 947037"
Return -ENOTSUPP instead of -1 from ->chip_init_tail() before migrating
this driver to use nand_scan() and transform this function to be a
callback run by the core.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Two helpers have been added to the core to do all kind of controller
side configuration/initialization between the detection phase and the
final NAND scan. Implement these hooks so that we can convert the driver
to just use nand_scan() instead of the nand_scan_ident() +
nand_scan_tail() pair.
Also change the unused "struct device *dev" parameter of the driver
structure into a platform device to reuse it in the ->attach_chip()
hook.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
We don't use the GPIO API in this driver, let's just remove the
<linux/gpio.h> inclusion.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
gpio/consumer.h defines everything we need, and it's clearly stated in
gpio.h that GPIO consumers should directly stop including gpio.h if they
can.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Commit ddd5ed3a90 ("mtd: rawnand: sunxi: Remove support for
GPIO-based Ready/Busy polling") removed GPIO-based RB polling. We no
longer need to include gpio headers.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
GPIO consumers should no longer include <linux/gpio.h>, and instead
include <linux/gpio/consumer.h>.
Also, explicitly include <include/io.h> since it seems to be missing
after switching to <linux/gpio/consumer.h>.
This fixes a build error when selecting the driver without selecting
GPIOLIB, which can happen when COMPILE_TEST=y.
Fixes: 6968e07e81 ("mtd: rawnand: jz4740: Allow selection of this driver when COMPILE_TEST=y")
Reported-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
In order to remove the limitation that forbids dynamic allocation in
nand_scan_ident(), we must create a path that will be the same for all
controller drivers. The idea is to use nand_scan() instead of the widely
used nand_scan_ident()/nand_scan_tail() couple. In order to achieve
this, controller drivers will need to adjust some parameters between
these two functions depending on the NAND chip wired on them.
This takes the form of two new hooks (->{attach,detach}_chip()) that are
placed in a new nand_controller_ops structure, which is then attached
to the nand_controller object at driver initialization time.
->attach_chip() is called between nand_scan_ident() and
nand_scan_tail(), and ->detach_chip() is called in the error path of
nand_scan() and in nand_cleanup().
Note that some NAND controller drivers don't have a dedicated
nand_controller object and instead rely on the default/dummy one
embedded in nand_chip. If you're in this case and still want to
initialize the controller ops, you'll have to manipulate
chip->dummy_controller directly.
Last but not least, it's worth mentioning that we plan to move some of
the controller related hooks placed in nand_chip into
nand_controller_ops to make the separation between NAND chip and NAND
controller methods clearer.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
In the raw NAND core, a NAND chip is described by a nand_chip structure,
while a NAND controller is described with a nand_hw_control structure
which is not very meaningful.
Rename this structure nand_controller.
As the structure gets renamed, it is logical to also rename the core
function initializing it from nand_hw_control_init() to
nand_controller_init().
Lastly, the 'hwcontrol' entry of the nand_chip structure is not
meaningful neither while it has the role of fallback when no controller
structure is provided by the driver (the controller driver is dumb and
can only control a single chip). Thus, it is renamed dummy_controller.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Linus Torvalds