Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
IRQ_DOMAIN is a hidden config option, so depending on it doesn't
make any sense. Select the config option because it's required to
compile this driver.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tracepoints to retrieve information about read, write
and non-data commands. For performance measurement support
tracepoints are added at the beginning and at the end of
transfers. Following is a list showing the new tracepoint
events. The "cmd" parameter here represents the opcode, SID,
and full 16-bit address.
spmi_write_begin: cmd and data buffer.
spmi_write_end : cmd and return value.
spmi_read_begin : cmd.
spmi_read_end : cmd, return value and data buffer.
spmi_cmd : cmd.
The reason that cmd appears at both the beginning and at
the end event is that SPMI drivers can request commands
concurrently. cmd helps in matching the corresponding
events.
SPMI tracepoints can be enabled like:
echo 1 >/sys/kernel/debug/tracing/events/spmi/enable
and will dump messages that can be viewed in
/sys/kernel/debug/tracing/trace that look like:
... spmi_read_begin: opc=56 sid=00 addr=0x0000
... spmi_read_end: opc=56 sid=00 addr=0x0000 ret=0 len=02 buf=0x[01-40]
... spmi_write_begin: opc=48 sid=00 addr=0x0000 len=3 buf=0x[ff-ff-ff]
Suggested-by: Sagar Dharia <sdharia@codeaurora.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Gilad Avidov <gavidov@codeaurora.org>
Signed-off-by: Ankit Gupta <ankgupta@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use irq_desc_get_xxx() to avoid redundant lookup of irq_desc while we
already have a pointer to corresponding irq_desc.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: http://lkml.kernel.org/r/20150713151750.915477120@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Chained irq handlers usually set up handler data as well. We now have
a function to set both under irq_desc->lock. Replace the two calls
with one.
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Link: http://lkml.kernel.org/r/20150713151750.831790045@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Not all architectures have io memory.
Fixes:
drivers/built-in.o: In function `spmi_pmic_arb_probe':
spmi-pmic-arb.c:(.text+0x1ed399): undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qualcomm PMIC arbiter driver already depends on ARCH_QCOM,
which could be either ARM or ARM64. New version of the PMIC
arbiter controller is available on 64 bit platforms.
Remove ARM dependency to allow driver to be build for 64 bit
platforms.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qualcomm PMIC Arbiter version-2 changes from version-1 are:
- Some different register offsets.
- New channel register space, one per PMIC peripheral (ppid).
All tx traffic uses these channels.
- New observer register space. All rx trafic uses this space.
- Different command format for spmi command registers.
Reviewed-by: Sagar Dharia <sdharia@codeaurora.org>
Signed-off-by: Gilad Avidov <gavidov@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to spmi spec a slave powers up into startup state and then
transitions into active state. Thus, the wakeup command is not required
before calling the slave's probe. The wakeup command is only needed for
slaves that are in sleep state after receiving the sleep command.
Cc: galak@codeaurora.org
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Sagar Dharia <sdharia@codeaurora.org>
Acked-by: Josh Cartwright <joshc@eso.teric.us>
Signed-off-by: Gilad Avidov <gavidov@codeaurora.org>
Tested-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SPMI defines the behavior of a device in the "SLEEP" state as being
"user-defined or specified by the device manufacturer". Without
clearly-defined bus-level semantics for low-power states, push the
responsibility of transitioning a device into/out of "SLEEP" into SPMI
device drivers.
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the split of Qualcomm MSM support into legacy and multiplatform,
the SPMI PMIC arb driver is only relevant on the multiplatform supported
SoCs. Switch the Kconfig depends to ARCH_QCOM.
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm PMIC Arbiter, in addition to being a basic SPMI controller,
also implements interrupt handling for slave devices. Note, this is
outside the scope of SPMI, as SPMI leaves interrupt handling completely
unspecified.
Extend the driver to provide a irq_chip implementation and chained irq
handling which allows for these interrupts to be used.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Qualcomm's PMIC Arbiter SPMI controller functions as a bus master and
is used to communication with one or more PMIC (slave) devices on the
SPMI bus. The PMIC Arbiter is actually a hardware wrapper around the
SPMI controller that provides concurrent and autonomous PMIC access
to various entities that need to communicate with the PMIC.
The SPMI controller hardware handles all of the SPMI bus activity (bus
arbitration, sequence start condition, transmission of frames, etc).
This software driver uses the PMIC Arbiter register interface to
initiate command sequences on the SPMI bus. The status register is
read to determine when the command sequence has completed and whether
or not it completed successfully.
Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
System Power Management Interface (SPMI) is a specification
developed by the MIPI (Mobile Industry Process Interface) Alliance
optimized for the real time control of Power Management ICs (PMIC).
SPMI is a two-wire serial interface that supports up to 4 master
devices and up to 16 logical slaves.
The framework supports message APIs, multiple busses (1 controller
per bus) and multiple clients/slave devices per controller.
Signed-off-by: Kenneth Heitke <kheitke@codeaurora.org>
Signed-off-by: Michael Bohan <mbohan@codeaurora.org>
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
