This nukes the following warning that is seen when building without
OF support:
drivers/gpio/gpio-davinci.c:437:25: warning: ‘keystone_gpio_get_irq_chip’ defined but not used [-Wunused-function]
static struct irq_chip *keystone_gpio_get_irq_chip(unsigned int irq)
^~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the pinmux gpio ranges feature to the DaVinci gpio
driver. Only device tree is supported since the non-DT boards don't
use a generic pinmux controller.
Cc: Keerthy <j-keerthy@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Disallow open drain and open source flags to be set
simultaneously. This doesn't make electrical sense, and would
the hardware actually respond to this setting, the result
would be short circuit.
- ACPI GPIO has a new core infrastructure for handling quirks.
The quirks are there to deal with broken ACPI tables centrally
instead of pushing the work to individual drivers. In the world
of BIOS writers, the ACPI tables are perfect. Until they find a
mistake in it. When such a mistake is found, we can patch it
with a quirk. It should never happen, the problem is that it
happens. So we accomodate for it.
- Several documentation updates.
- Revert the patch setting up initial direction state from
reading the device. This was causing bad things for drivers
that can't read status on all its pins. It is only affecting
debugfs information quality.
- Label descriptors with the device name if no explicit label is
passed in.
- Pave the ground for transitioning SPI and regulators to use
GPIO descriptors by implementing some quirks in the device tree
GPIO parsing code.
New drivers:
- New driver for the Access PCIe IDIO 24 family.
Other:
- Major refactorings and improvements to the GPIO mockup driver
used for test and verification.
- Moved the AXP209 driver over to pin control since it gained a
pin control back-end. These patches will appear (with the same
hashes) in the pin control pull request as well.
- Convert the onewire GPIO driver w1-gpio to use descriptors.
This is merged here since the W1 maintainers send very few
pull requests and he ACKed it.
- Start to clean up driver headers using <linux/gpio.h> to just
use <linux/gpio/driver.h> as appropriate.
-----BEGIN PGP SIGNATURE-----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=k5nL
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"The is the bulk of GPIO changes for the v4.16 kernel cycle. It is
pretty calm this time around I think. I even got time to get to things
like starting to clean up header includes.
Core changes:
- Disallow open drain and open source flags to be set simultaneously.
This doesn't make electrical sense, and would the hardware actually
respond to this setting, the result would be short circuit.
- ACPI GPIO has a new core infrastructure for handling quirks. The
quirks are there to deal with broken ACPI tables centrally instead
of pushing the work to individual drivers. In the world of BIOS
writers, the ACPI tables are perfect. Until they find a mistake in
it. When such a mistake is found, we can patch it with a quirk. It
should never happen, the problem is that it happens. So we
accomodate for it.
- Several documentation updates.
- Revert the patch setting up initial direction state from reading
the device. This was causing bad things for drivers that can't read
status on all its pins. It is only affecting debugfs information
quality.
- Label descriptors with the device name if no explicit label is
passed in.
- Pave the ground for transitioning SPI and regulators to use GPIO
descriptors by implementing some quirks in the device tree GPIO
parsing code.
New drivers:
- New driver for the Access PCIe IDIO 24 family.
Other:
- Major refactorings and improvements to the GPIO mockup driver used
for test and verification.
- Moved the AXP209 driver over to pin control since it gained a pin
control back-end. These patches will appear (with the same hashes)
in the pin control pull request as well.
- Convert the onewire GPIO driver w1-gpio to use descriptors. This is
merged here since the W1 maintainers send very few pull requests
and he ACKed it.
- Start to clean up driver headers using <linux/gpio.h> to just use
<linux/gpio/driver.h> as appropriate"
* tag 'gpio-v4.16-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (103 commits)
gpio: Timestamp events in hardirq handler
gpio: Fix kernel stack leak to userspace
gpio: Fix a documentation spelling mistake
gpio: Documentation update
gpiolib: remove redundant initialization of pointer desc
gpio: of: Fix NPE from OF flags
gpio: stmpe: Delete an unnecessary variable initialisation in stmpe_gpio_probe()
gpio: stmpe: Move an assignment in stmpe_gpio_probe()
gpio: stmpe: Improve a size determination in stmpe_gpio_probe()
gpio: stmpe: Use seq_putc() in stmpe_dbg_show()
gpio: No NULL owner
gpio: stmpe: i2c transfer are forbiden in atomic context
gpio: davinci: Include proper header
gpio: da905x: Include proper header
gpio: cs5535: Include proper header
gpio: crystalcove: Include proper header
gpio: bt8xx: Include proper header
gpio: bcm-kona: Include proper header
gpio: arizona: Include proper header
gpio: amd8111: Include proper header
...
This driver has no business including <linux/gpio.h>, it is a
driver so include <linux/gpio/driver.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As per the re-design assign the first bank regs for unbanked
irq case. This was missed out in the original patch.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: b5cf3fd827 ("gpio: davinci: Redesign driver to accommodate ngpios in one gpio chip")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently davinci_gpio_irq_setup return value is ignored. Handle the
return value appropriately.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case of devm_clk_get failure use dev_err instead of printk
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the devm version of gpiochip_add_data and pass on the
return value. This avoids memory leak due to gpiochip_add_data
in case the driver is unbound.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the interrupt descriptors it allocates. Fix
it by using the resource managed version of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the current redesign of driver it's not necessary to have
custom .xlate() as the gpiolib will assign default of_gpio_simple_xlate().
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update GPIO driver to support Multiple GPIO controllers by updating
the base of subsequent GPIO chips with total of previous chips
gpio count so that gpio_add_chip gets unique numbers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Davinci GPIO driver is implemented to work with one monolithic
Davinci GPIO platform device which may have up to Y(144) gpios.
The Davinci GPIO driver instantiates number of GPIO chips with
max 32 gpio pins per each during initialization and one IRQ domain.
So, the current GPIO's opjects structure is:
<platform device> Davinci GPIO controller
|- <gpio0_chip0> ------|
... |--- irq_domain (hwirq [0..143])
|- <gpio0_chipN> ------|
Current driver creates one chip for every 32 GPIOs in a controller.
This was a limitation earlier now there is no need for that. Hence
redesigning the driver to create one gpio chip for all the ngpio
in the controller.
|- <gpio0_chip0> ------|--- irq_domain (hwirq [0..143]).
The previous discussion on this can be found here:
https://www.spinics.net/lists/linux-omap/msg132869.html
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio2regs is written making an assumption that driver supports only
one instance of gpio controller. Removing this and adding a generic
array so as to support multiple instances of gpio controllers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
davinci_gpio_controller struct has set_data, in_data, clr_data
members that are assigned and never used.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpiod framework uses the chip label to match a specific chip.
The davinci gpio driver, creates several chips using always the same
label, which is not compatible with gpiod.
To allow platform data to declare gpio lookup tables, and for drivers
to use the gpiod framework, allocate unique label per registered chip.
Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a possible NULL pointer deference in the function,
davinci_gpio_probe due to the function, gpio2regs being able
to return a NULL pointer if it rans to get the registers for
the gpio devices on a davinci board. Furthermore if this does
arise return -ENXIO to signal callers that this case has arisen
and avoiding setting the regs or other pointer values on the
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver only needs to allocate for [ngpio / 32] controllers,
as each controller handles 32 gpios. But the current driver
allocates for ngpio of which the extra allocated are unused.
Fix it be registering only the required number of controllers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the first parameter of irq_domain_add_legacy is NULL.
irq_find_host function returns NULL when we do not populate the of_node
and hence irq_of_parse_and_map call fails whenever we want to request a
gpio irq. This fixes the request_irq failures for gpio interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I missed to convert this driver properly to use .parent to
point to the parent device. ARMv7 multiplatform would not
compile.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Nizam Haider <nijamh@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most interrupt flow handlers do not use the irq argument. Those few
which use it can retrieve the irq number from the irq descriptor.
Remove the argument.
Search and replace was done with coccinelle and some extra helper
scripts around it. Thanks to Julia for her help!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed as most platforms don't use probing.
There appears to be a great deal of blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Interrupts for GPIOs 16 through 31 are enabled by bit 1 in the
"binten" register (offset 8). Previous versions of GPIO only
used bit 0, which enables GPIO 0-15 interrupts.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix a race where a pending interrupt could be received and the handler
called before the handler's data has been setup, by converting to
irq_set_chained_handler_and_data().
Search and conversion was done with coccinelle.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
It's pretty silly to do
void *cd = irq_get_chip_data(irq_data->irq);
because that results in cd = irq_data->chip_data, but goes through a
redundant lookup of the irq_data. Use irq_data directly.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: linux-gpio@vger.kernel.org
The irq argument of most interrupt flow handlers is unused or merily
used instead of a local variable. The handlers which need the irq
argument can retrieve the irq number from the irq descriptor.
Search and update was done with coccinelle and the invaluable help of
Julia Lawall.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
This is a preparatory patch for moving irq_data struct members.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver missed an of_xlate function to translate gpio numbers
as found in the DT to the correct chip and number.
While there I've set #gpio_cells to a fixed value of 2.
I've used gpio-pxa.c as template for those changes and tested my changes
successfully on a da850 board using entries for gpio-leds in a DT. So I didn't
reinvent the wheel but just copied and tested stuff.
Thanks to Grygorii Strashko for the hint to the existing code in gpio-pxa.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The similar GPIO HW block is used by keystone SoCs as
in Davinci SoCs.
Hence, reuse Davinci GPIO driver for Keystone taking into
account that Keystone contains ARM GIC IRQ controller which
is implemented using IRQ Chip.
Documentation:
http://www.ti.com/lit/ug/sprugv1/sprugv1.pdf
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Variable 'irq' is declared as unsigned and then used to store
negative return values from irq_alloc_descs() such as -EINVAL.
This patch fix this by declaring the variable as a signed.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The system may crash if:
- there are more than 1 banks
- unbanked irqs are enabled
- someone will call gpio_to_irq() for GPIO from bank2 or above
Hence, fix it by not creating irq_domain if unbanked irqs are enabled
and correct gpio_to_irq_banked() to handle this properly.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
It's unsafe to call IRQ chip callbacks (.irq_mask/irq_unmask/irq_ack)
from chained IRQ handler directly. Because, Davinci GPIO block is used
by different SoCs, which, in turn, have different Main IRQ controllers
(Davinci - aintc, cp-intc; Keystone - arm-gic) which may introduce
diffrent set of IRQ chip callbacks. As result, call of
gpio_irq_handler() on Keysone will simply cause crash the system,
because ARM-GIC implements .irq_eoi() instead of .irq_ack().
Hence, fix it by using Kernel chained_irq_enter/chained_irq_exit APIs as
they are intended to handle exact such cases.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch adds OF parser support for davinci gpio
driver and also appropriate documentation in gpio-davinci.txt
located at Documentation/devicetree/bindings/gpio/.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: KV Sujith <sujithkv@ti.com>
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
[prabhakar.csengg@gmail.com: simplified the OF code, removed
unnecessary DT property and also simplified
the commit message]
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Convert the davinci gpio driver to use irqdomain support.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
[grygorii.strashko@ti.com:
- switch to use one irq-domain per all GPIO banks
- keep irq_create_mapping() call in gpio_to_irq_banked() as it
simply transformed to irq_find_mapping() if IRQ mapping exist
already]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Since Davinci GPIO driver is moved to support gpiolib it has to use
ARCH_NR_GPIOS (can be configured using CONFIG_ARCH_NR_GPIO Kconfig
option) configuration instead of any mach/platform specific options.
Hence, replace private DAVINCI_N_GPIO with common ARCH_NR_GPIOS. This is
safe because default value for ARCH_NR_GPIOS=256 and maximum number of
supported GPIOs for Davinci is DAVINCI_N_GPIO=144.
More over, this is one of steps to re-use Davinci GPIO driver by other
mach/platform.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch replaces the __raw_readl/writel with
{readl|writel}_relaxed(), Altough the code runs on ARMv5
based SOCs, changing this will help using code for other
use cases (like with big-endian machines).
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch fixes a check for offset in gpio_to_irq_unbanked()
and also assigns gpio_irq, gpio_unbanked of chips[0] to
appropriate values which is used in gpio_to_irq_unbanked()
function.
Without this patch, unbanked IRQ handling is broken.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Modify DaVinci GPIO driver to become a platform device
driver.
The driver does not have platform driver structure or
a probe. Instead, it has pure_initcall function for
initialization. The platform specific informaiton is
obtained using the DaVinci specific davinci_soc_info
structure. This is a problem for Device Tree (DT)
implementation.
As a first stage of DT conversion, we implement a probe.
Additional notes:
- The driver registration happens as postcore_initcall.
This is required since machine init functions like
da850_lcd_hw_init() make use of GPIO.
- Start using devres APIs for simpler error handling.
Signed-off-by: KV Sujith <sujithkv@ti.com>
[avinashphilip@ti.com: Move global definition of
"davinci_gpio_controller" to local]
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
[nsekhar@ti.com: drop unused structure member, rebase to new
clean-up patch and fix error messages]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Kees Cook