We recently added a kfree() after the end of the loop:
if (retries == RETRIES) {
kfree(reply);
return -EINVAL;
}
There are two problems. First the test is wrong and because retries
equals RETRIES if we succeed on the last iteration through the loop.
Second if we fail on the last iteration through the loop then the kfree
is a double free.
When you're reading this code, please note the break statement at the
end of the while loop. This patch changes the loop so that if it's not
successful then "reply" is NULL and we can test for that afterward.
Cc: <stable@vger.kernel.org>
Fixes: 6b7c3b86f0 ("drm/vmwgfx: fix memory leak when too many retries have occurred")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
The problem can be seen in the following two tests:
0: (bf) r3 = r10
1: (55) if r3 != 0x7b goto pc+0
2: (7a) *(u64 *)(r3 -8) = 0
3: (79) r4 = *(u64 *)(r10 -8)
..
0: (85) call bpf_get_prandom_u32#7
1: (bf) r3 = r10
2: (55) if r3 != 0x7b goto pc+0
3: (7b) *(u64 *)(r3 -8) = r0
4: (79) r4 = *(u64 *)(r10 -8)
When backtracking need to mark R4 it will mark slot fp-8.
But ST or STX into fp-8 could belong to the same block of instructions.
When backtracing is done the parent state may have fp-8 slot
as "unallocated stack". Which will cause verifier to warn
and incorrectly reject such programs.
Writes into stack via non-R10 register are rare. llvm always
generates canonical stack spill/fill.
For such pathological case fall back to conservative precision
tracking instead of rejecting.
Reported-by: syzbot+c8d66267fd2b5955287e@syzkaller.appspotmail.com
Fixes: b5dc0163d8 ("bpf: precise scalar_value tracking")
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
When creating a v4 route that uses a v6 nexthop from a nexthop group.
Allow the kernel to properly send the nexthop as v6 via the RTA_VIA
attribute.
Broken behavior:
$ ip nexthop add via fe80::9 dev eth0
$ ip nexthop show
id 1 via fe80::9 dev eth0 scope link
$ ip route add 4.5.6.7/32 nhid 1
$ ip route show
default via 10.0.2.2 dev eth0
4.5.6.7 nhid 1 via 254.128.0.0 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
$
Fixed behavior:
$ ip nexthop add via fe80::9 dev eth0
$ ip nexthop show
id 1 via fe80::9 dev eth0 scope link
$ ip route add 4.5.6.7/32 nhid 1
$ ip route show
default via 10.0.2.2 dev eth0
4.5.6.7 nhid 1 via inet6 fe80::9 dev eth0
10.0.2.0/24 dev eth0 proto kernel scope link src 10.0.2.15
$
v2, v3: Addresses code review comments from David Ahern
Fixes: dcb1ecb50e (“ipv4: Prepare for fib6_nh from a nexthop object”)
Signed-off-by: Donald Sharp <sharpd@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Ahern says:
====================
nexthops: Fix multipath notifications for IPv6 and selftests
A couple of bug fixes noticed while testing Donald's patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanups of the tests in fib_nexthops.sh
1. Several tests noted unexpected route output, but the
discrepancy was not showing in the summary output and
overlooked in the verbose output. Add a WARNING message
to the summary output to make it clear a test is not showing
expected output.
2. Several check_* calls are missing extra data like scope and metric
causing mismatches when the nexthops or routes are correct - some of
them are a side effect of the evolving iproute2 command. Update the
data to the expected output.
3. Several check_routes are checking for the wrong nexthop data,
most likely a copy-paste-update error.
4. A couple of tests were re-using a nexthop id that already existed.
Fix those to use a new id.
Fixes: 6345266a99 ("selftests: Add test cases for nexthop objects")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A change to the core nla helpers was missed during the push of
the nexthop changes. rt6_fill_node_nexthop should be calling
nla_nest_start_noflag not nla_nest_start. Currently, iproute2
does not print multipath data because of parsing issues with
the attribute.
Fixes: f88d8ea67f ("ipv6: Plumb support for nexthop object in a fib6_info")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sock_map and ULP only work together when ULP is loaded after the sock
map is loaded. In the sock_map case we added a check for this to fail
the load if ULP is already set. However, we missed the check on the
sock_hash side.
Add a ULP check to the sock_hash update path.
Fixes: 604326b41a ("bpf, sockmap: convert to generic sk_msg interface")
Reported-by: syzbot+7a6ee4d0078eac6bf782@syzkaller.appspotmail.com
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add forward declaration for struct gpio_desc in order to address
the following:
./include/linux/phy_fixed.h:48:17: error: 'struct gpio_desc' declared inside parameter list [-Werror]
./include/linux/phy_fixed.h:48:17: error: its scope is only this definition or declaration, which is probably not what you want [-Werror]
Fixes: 71bd106d25 ("net: fixed-phy: Add fixed_phy_register_with_gpiod() API")
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth 2019-09-05
Here are a few more Bluetooth fixes for 5.3. I hope they can still make
it. There's one USB ID addition for btusb, two reverts due to discovered
regressions, and two other important fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c49a8682fc.
There are devices which require low connection intervals for usable operation
including keyboards and mice. Forcing a static connection interval for
these types of devices has an impact in latency and causes a regression.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds myself as the Google contact for embargoed hardware security
issues and fixes some small typos.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Matt Linton <amuse@google.com>
Cc: Matthew Garrett <mjg59@google.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Guenter Roeck <groeck@chromium.org>
Link: https://lore.kernel.org/r/201909040922.56496BF70@keescook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a subtle change in behaviour introduced by:
commit c7a1ce397a
'ipv6: Change addrconf_f6i_alloc to use ip6_route_info_create'
Before that patch /proc/net/ipv6_route includes:
00000000000000000000000000000001 80 00000000000000000000000000000000 00 00000000000000000000000000000000 00000000 00000003 00000000 80200001 lo
Afterwards /proc/net/ipv6_route includes:
00000000000000000000000000000001 80 00000000000000000000000000000000 00 00000000000000000000000000000000 00000000 00000002 00000000 80240001 lo
ie. the above commit causes the ::1/128 local (automatic) route to be flagged with RTF_ADDRCONF (0x040000).
AFAICT, this is incorrect since these routes are *not* coming from RA's.
As such, this patch restores the old behaviour.
Fixes: c7a1ce397a ("ipv6: Change addrconf_f6i_alloc to use ip6_route_info_create")
Cc: David Ahern <dsahern@gmail.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transport should use its own pf_retrans to do the error_count
check, instead of asoc's. Otherwise, it's meaningless to make
pf_retrans per transport.
Fixes: 5aa93bcf66 ("sctp: Implement quick failover draft from tsvwg")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a misplaced traceline in rxrpc_input_packet() which is looking at a
packet that just got released rather than the replacement packet.
Fix this by moving the traceline after the assignment that moves the new
packet pointer to the actual packet pointer.
Fixes: d0d5c0cd1e ("rxrpc: Use skb_unshare() rather than skb_cow_data()")
Reported-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for net:
1) br_netfilter drops IPv6 packets if ipv6 is disabled, from Leonardo Bras.
2) nft_socket hits BUG() due to illegal skb->sk caching, patch from
Fernando Fernandez Mancera.
3) nft_fib_netdev could be called with ipv6 disabled, leading to crash
in the fib lookup, also from Leonardo.
4) ctnetlink honors IPS_OFFLOAD flag, just like nf_conntrack sysctl does.
5) Properly set up flowtable entry timeout, otherwise immediate
removal by garbage collector might occur.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that attribute methods are not called after the item
has been removed from the tree. To do so, we
* at the point of no return in removals, grab ->frag_sem
exclusive and mark the fragment dead.
* call the methods of attributes with ->frag_sem taken
shared and only after having verified that the fragment is still
alive.
The main benefit is for method instances - they are
guaranteed that the objects they are accessing *and* all ancestors
are still there. Another win is that we don't need to bother
with extra refcount on config_item when opening a file -
the item will be alive for as long as it stays in the tree, and
we won't touch it/attributes/any associated data after it's
been removed from the tree.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Thadeu Lima de Souza Cascardo reported that 'chrt' broke on recent kernels:
$ chrt -p $$
chrt: failed to get pid 26306's policy: Argument list too long
and he has root-caused the bug to the following commit increasing sched_attr
size and breaking sched_read_attr() into returning -EFBIG:
a509a7cd79 ("sched/uclamp: Extend sched_setattr() to support utilization clamping")
The other, bigger bug is that the whole sched_getattr() and sched_read_attr()
logic of checking non-zero bits in new ABI components is arguably broken,
and pretty much any extension of the ABI will spuriously break the ABI.
That's way too fragile.
Instead implement the perf syscall's extensible ABI instead, which we
already implement on the sched_setattr() side:
- if user-attributes have the same size as kernel attributes then the
logic is unchanged.
- if user-attributes are larger than the kernel knows about then simply
skip the extra bits, but set attr->size to the (smaller) kernel size
so that tooling can (in principle) handle older kernel as well.
- if user-attributes are smaller than the kernel knows about then just
copy whatever user-space can accept.
Also clean up the whole logic:
- Simplify the code flow - there's no need for 'ret' for example.
- Standardize on 'kattr/uattr' and 'ksize/usize' naming to make sure we
always know which side we are dealing with.
- Why is it called 'read' when what it does is to copy to user? This
code is so far away from VFS read() semantics that the naming is
actively confusing. Name it sched_attr_copy_to_user() instead, which
mirrors other copy_to_user() functionality.
- Move the attr->size assignment from the head of sched_getattr() to the
sched_attr_copy_to_user() function. Nothing else within the kernel
should care about the size of the structure.
With these fixes the sched_getattr() syscall now nicely supports an
extensible ABI in both a forward and backward compatible fashion, and
will also fix the chrt bug.
As an added bonus the bogus -EFBIG return is removed as well, which as
Thadeu noted should have been -E2BIG to begin with.
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Cc: Arnaldo Carvalho de Melo <acme@infradead.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Patrick Bellasi <patrick.bellasi@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: a509a7cd79 ("sched/uclamp: Extend sched_setattr() to support utilization clamping")
Link: https://lkml.kernel.org/r/20190904075532.GA26751@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When returning from bpa10x_send_frame, it is necessary to propagate any
potential errno returned from usb_submit_urb.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Looks like Deadlock is observed in hci_qca while performing
stress and stability tests. Since same lock is getting
acquired from qca_wq_awake_rx and hci_ibs_tx_idle_timeout
seeing spinlock recursion, irqs should be disable while
acquiring the spinlock always.
Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
* R-Car D3 (r8a77995) based Draak Board
- Correct backlight regulator name in device tree
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE4nzZofWswv9L/nKF189kaWo3T74FAl1WsAkACgkQ189kaWo3
T76iZA//ST+Llf3DLMcmhFHci2ld8khWl+NcxVAKDjDXgxZ85jxqzxs2b8kshYoV
xAIdt+zwS5GOXpXjDbuw2uufLTEGrmS8v98NxBlxvmdr35PKQE6wXRs+YfisXlhL
bnY4pG8AT3NnN8iiQ4DWkRVmfvc2joaWmyczELvrPCSzLtguCAkjm9m7hfPiVxT+
L5tf01LhYGxRdYoXI/c+kIDyYfgQOhcGMkIk22R3p+l9QM2NE8HqhMPqAqPLYTNA
c/bueDoPxyFdNp7drPMTdkWzovQ0fsslXT1GvbZ6MHJN4e2OurcGHsoU5m/gUJrH
f6C6y3Jw/nInRI13SeI3hAAHnmycND1O5TPqfYMJksmJU2c5x1Zabj2Su4ztNUPa
rMxF4wgqPzqLXDT1xcCacdgUketgYrRmcGUE/KkEIZxcx2eVrLN9TSZ8iOr0ic/E
pwxWUF9OobNYb20sJEiV3esYAwcQq/tqSnr6Hd4vBd2ptqZAOq81mfvt4wnJuwuO
jAAtyV7cdO49lpKf97WfCdqZvArpohKoF6w4Zi9TDBtFGkOj5lkNATc7w6eJkcye
vUDmJ2+9zR+auGMCn3kwzG62yO4KJDnGJgjxMsXh1Kt1MQgpVI2wTFczJUaC4/M2
Lcq+pShfI1qYvAeyy+80RRkR5jiyfGncrrpq1dnYeX6HC8E946w=
=YACQ
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/fixes
Renesas ARM Based SoC Fixes for v5.3
* R-Car D3 (r8a77995) based Draak Board
- Correct backlight regulator name in device tree
* tag 'renesas-fixes-for-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: r8a77995: draak: Fix backlight regulator name
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
When in userspace and MSR FP=0 the hardware FP state is unrelated to
the current process. This is extended for transactions where if tbegin
is run with FP=0, the hardware checkpoint FP state will also be
unrelated to the current process. Due to this, we need to ensure this
hardware checkpoint is updated with the correct state before we enable
FP for this process.
Unfortunately we get this wrong when returning to a process from a
hardware interrupt. A process that starts a transaction with FP=0 can
take an interrupt. When the kernel returns back to that process, we
change to FP=1 but with hardware checkpoint FP state not updated. If
this transaction is then rolled back, the FP registers now contain the
wrong state.
The process looks like this:
Userspace: Kernel
Start userspace
with MSR FP=0 TM=1
< -----
...
tbegin
bne
Hardware interrupt
---- >
<do_IRQ...>
....
ret_from_except
restore_math()
/* sees FP=0 */
restore_fp()
tm_active_with_fp()
/* sees FP=1 (Incorrect) */
load_fp_state()
FP = 0 -> 1
< -----
Return to userspace
with MSR TM=1 FP=1
with junk in the FP TM checkpoint
TM rollback
reads FP junk
When returning from the hardware exception, tm_active_with_fp() is
incorrectly making restore_fp() call load_fp_state() which is setting
FP=1.
The fix is to remove tm_active_with_fp().
tm_active_with_fp() is attempting to handle the case where FP state
has been changed inside a transaction. In this case the checkpointed
and transactional FP state is different and hence we must restore the
FP state (ie. we can't do lazy FP restore inside a transaction that's
used FP). It's safe to remove tm_active_with_fp() as this case is
handled by restore_tm_state(). restore_tm_state() detects if FP has
been using inside a transaction and will set load_fp and call
restore_math() to ensure the FP state (checkpoint and transaction) is
restored.
This is a data integrity problem for the current process as the FP
registers are corrupted. It's also a security problem as the FP
registers from one process may be leaked to another.
Similarly for VMX.
A simple testcase to replicate this will be posted to
tools/testing/selftests/powerpc/tm/tm-poison.c
This fixes CVE-2019-15031.
Fixes: a7771176b4 ("powerpc: Don't enable FP/Altivec if not checkpointed")
Cc: stable@vger.kernel.org # 4.15+
Signed-off-by: Gustavo Romero <gromero@linux.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190904045529.23002-2-gromero@linux.vnet.ibm.com
When we take an FP unavailable exception in a transaction we have to
account for the hardware FP TM checkpointed registers being
incorrect. In this case for this process we know the current and
checkpointed FP registers must be the same (since FP wasn't used
inside the transaction) hence in the thread_struct we copy the current
FP registers to the checkpointed ones.
This copy is done in tm_reclaim_thread(). We use thread->ckpt_regs.msr
to determine if FP was on when in userspace. thread->ckpt_regs.msr
represents the state of the MSR when exiting userspace. This is setup
by check_if_tm_restore_required().
Unfortunatley there is an optimisation in giveup_all() which returns
early if tsk->thread.regs->msr (via local variable `usermsr`) has
FP=VEC=VSX=SPE=0. This optimisation means that
check_if_tm_restore_required() is not called and hence
thread->ckpt_regs.msr is not updated and will contain an old value.
This can happen if due to load_fp=255 we start a userspace process
with MSR FP=1 and then we are context switched out. In this case
thread->ckpt_regs.msr will contain FP=1. If that same process is then
context switched in and load_fp overflows, MSR will have FP=0. If that
process now enters a transaction and does an FP instruction, the FP
unavailable will not update thread->ckpt_regs.msr (the bug) and MSR
FP=1 will be retained in thread->ckpt_regs.msr. tm_reclaim_thread()
will then not perform the required memcpy and the checkpointed FP regs
in the thread struct will contain the wrong values.
The code path for this happening is:
Userspace: Kernel
Start userspace
with MSR FP/VEC/VSX/SPE=0 TM=1
< -----
...
tbegin
bne
fp instruction
FP unavailable
---- >
fp_unavailable_tm()
tm_reclaim_current()
tm_reclaim_thread()
giveup_all()
return early since FP/VMX/VSX=0
/* ckpt MSR not updated (Incorrect) */
tm_reclaim()
/* thread_struct ckpt FP regs contain junk (OK) */
/* Sees ckpt MSR FP=1 (Incorrect) */
no memcpy() performed
/* thread_struct ckpt FP regs not fixed (Incorrect) */
tm_recheckpoint()
/* Put junk in hardware checkpoint FP regs */
....
< -----
Return to userspace
with MSR TM=1 FP=1
with junk in the FP TM checkpoint
TM rollback
reads FP junk
This is a data integrity problem for the current process as the FP
registers are corrupted. It's also a security problem as the FP
registers from one process may be leaked to another.
This patch moves up check_if_tm_restore_required() in giveup_all() to
ensure thread->ckpt_regs.msr is updated correctly.
A simple testcase to replicate this will be posted to
tools/testing/selftests/powerpc/tm/tm-poison.c
Similarly for VMX.
This fixes CVE-2019-15030.
Fixes: f48e91e87e ("powerpc/tm: Fix FP and VMX register corruption")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190904045529.23002-1-gromero@linux.vnet.ibm.com
There is no reason to print warnings when balloon page allocation fails,
as they are expected and can be handled gracefully. Since VMware
balloon now uses balloon-compaction infrastructure, and suppressed these
warnings before, it is also beneficial to suppress these warnings to
keep the same behavior that the balloon had before.
Cc: Jason Wang <jasowang@redhat.com>
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
This reverts commit 7f466032dc ("vhost: access vq metadata through
kernel virtual address"). The commit caused a bunch of issues, and
while commit 73f628ec9e ("vhost: disable metadata prefetch
optimization") disabled the optimization it's not nice to keep lots of
dead code around.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
It is unnecessary to use ret variable to return the error
code, just return the error code directly.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
This change lowers ring buffer reclaim threshold from 1/2*queue to budget
for better performance. According to our test with qemu + dpdk, packet
dropping happens when the guest is not able to provide free buffer in
avail ring timely with default 1/2*queue. The value in the patch has been
tested and does show better performance.
Test setup: iperf3 to generate packets to guest (total 30mins, pps 400k, UDP)
avg packets drop before: 2842
avg packets drop after: 360(-87.3%)
Further, current code suffers from a starvation problem: the amount of
work done by try_fill_recv is not bounded by the budget parameter, thus
(with large queues) once in a while userspace gets blocked for a long
time while queue is being refilled. Trigger refills earlier to make sure
the amount of work to do is limited.
Signed-off-by: jiangkidd <jiangkidd@hotmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Since vhost_exceeds_weight() was introduced, callers need to specify
the packet weight and byte weight in vhost_dev_init(). Note that, the
packet weight isn't counted in this patch to keep the original behavior
unchanged.
Fixes: e82b9b0727 ("vhost: introduce vhost_exceeds_weight()")
Cc: stable@vger.kernel.org
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Since below commit, callers need to specify the iov_limit in
vhost_dev_init() explicitly.
Fixes: b46a0bf78a ("vhost: fix OOB in get_rx_bufs()")
Cc: stable@vger.kernel.org
Signed-off-by: Tiwei Bie <tiwei.bie@intel.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
This ThinkCentre machine has a new realtek codec alc222, it is not
in the support list, we add it in the realtek.c then this machine
can apply FIXUPs for the realtek codec.
And this machine has two front mics which can't be handled
by PA so far, it uses the pin 0x18 and 0x19 as the front mics, as
a result the existing FIXUP ALC294_FIXUP_LENOVO_MIC_LOCATION doesn't
work on this machine. Fortunately another FIXUP
ALC283_FIXUP_HEADSET_MIC also can change the location for one of the
two mics on this machine.
Link: https://lore.kernel.org/r/20190904055327.9883-1-hui.wang@canonical.com
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 20c169aceb ("dmaengine: rcar-dmac: clear pertinence
number of channels") forgets to clear the last channel by
DMACHCLR in rcar_dmac_init() (and doesn't need to clear the first
channel) if iommu is mapped to the device. So, this patch fixes it
by using "channels_mask" bitfield.
Note that the hardware and driver don't support more than 32 bits
in DMACHCLR register anyway, so this patch should reject more than
32 channels in rcar_dmac_parse_of().
Fixes: 20c169aceb ("dmaengine: rcar-dmac: clear pertinence number of channels")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/1567424643-26629-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
For the Spreadtrum DMA link-list mode, when the DMA engine got a slave
hardware request, which will trigger the DMA engine to load the DMA
configuration from the link-list memory automatically. But before the
slave hardware request, the slave will get an incorrect residue due
to the first node used to trigger the link-list was configured as the
last source address and destination address.
Thus we should make sure the first node was configured the start source
address and destination address, which can fix this issue.
Fixes: 4ac6954647 ("dmaengine: sprd: Support DMA link-list mode")
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Link: https://lore.kernel.org/r/77868edb7aff9d5cb12ac3af8827ef2e244441a6.1567150471.git.baolin.wang@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Set up the default timeout for this new entry otherwise the garbage
collector might quickly remove it right after the flowtable insertion.
Fixes: ac2a66665e ("netfilter: add generic flow table infrastructure")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If this flag is set, timeout and state are irrelevant to userspace.
Fixes: 90964016e5 ("netfilter: nf_conntrack: add IPS_OFFLOAD status bit")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If IPv6 is disabled on boot (ipv6.disable=1), but nft_fib_inet ends up
dealing with a IPv6 packet, it causes a kernel panic in
fib6_node_lookup_1(), crashing in bad_page_fault.
The panic is caused by trying to deference a very low address (0x38
in ppc64le), due to ipv6.fib6_main_tbl = NULL.
BUG: Kernel NULL pointer dereference at 0x00000038
The kernel panic was reproduced in a host that disabled IPv6 on boot and
have to process guest packets (coming from a bridge) using it's ip6tables.
Terminate rule evaluation when packet protocol is IPv6 but the ipv6 module
is not loaded.
Signed-off-by: Leonardo Bras <leonardo@linux.ibm.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Turns out the commit 3a0681c744 ("mmc: core: do not retry CMD6 in
__mmc_switch()") breaks initialization of a Toshiba THGBMNG5 eMMC card,
when using the meson-gx-mmc.c driver on a custom board based on Amlogic
A113D.
The CMD6 that switches the card into HS200 mode is then one that fails and
according to the below printed messages from the log:
[ 1.648951] mmc0: mmc_select_hs200 failed, error -84
[ 1.648988] mmc0: error -84 whilst initialising MMC card
After some analyze, it turns out that adding a delay of ~5ms inside
mmc_select_bus_width() but after mmc_compare_ext_csds() has been executed,
also fixes the problem. Adding yet some more debug code, trying to figure
out if potentially the card could be in a busy state, both by using CMD13
and ->card_busy() ops concluded that this was not the case.
Therefore, let's simply revert the commit that dropped support for retrying
of CMD6, as this also fixes the problem.
Fixes: 3a0681c744 ("mmc: core: do not retry CMD6 in __mmc_switch()")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Kaisrlik <ja.kaisrlik@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
`dev` (struct rsi_91x_usbdev *) field of adapter
(struct rsi_91x_usbdev *) is allocated and initialized in
`rsi_init_usb_interface`. If any error is detected in information
read from the device side, `rsi_init_usb_interface` will be
freed. However, in the higher level error handling code in
`rsi_probe`, if error is detected, `rsi_91x_deinit` is called
again, in which `dev` will be freed again, resulting double free.
This patch fixes the double free by removing the free operation on
`dev` in `rsi_init_usb_interface`, because `rsi_91x_deinit` is also
used in `rsi_disconnect`, in that code path, the `dev` field is not
(and thus needs to be) freed.
This bug was found in v4.19, but is also present in the latest version
of kernel. Fixes CVE-2019-15504.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 9ad3b55654.
As reported by Sergey:
"I got some problem after upgrade kernel to 5.2 version (debian testing
linux-image-5.2.0-2-amd64). 5Ghz client stopped to see AP.
Some tests with 1metre distance between client-AP: 2.4Ghz -22dBm, for
5Ghz - 53dBm !, for longer distance (8m + walls) 2.4 - 61dBm, 5Ghz not
visible."
It was identified that rx signal level degradation was caused by
9ad3b55654 ("rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band").
So revert this commit.
Cc: <stable@vger.kernel.org> # v5.1+
Reported-and-tested-by: Sergey Maranchuk <slav0nic0@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After looking at code I realized that my previous fix
9584412438 ("rt2x00: clear IV's on start to fix AP mode regression")
was incomplete. We can still have wrong IV's after re-keyring.
To fix that, clear up IV's also on key removal.
Fixes: 710e6cc159 ("rt2800: do not nullify initialization vector data")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
tested-by: Emil Karlson <jekarl@iki.fi>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We were erroneously assigning the new configuration to a local
variable cfg, but that was not being assigned to anything, so the
change was getting lost. Assign directly to iwl_trans->cfg instead.
Fixes: 5a8c31aa63 ("iwlwifi: pcie: fix recognition of QuZ devices")
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_update_vs_ie(),mwifiex_set_uap_rates() and
mwifiex_set_wmm_params() call memcpy() without checking
the destination size.Since the source is given from
user-space, this may trigger a heap buffer overflow.
Fix them by putting the length check before performing memcpy().
This fix addresses CVE-2019-14814,CVE-2019-14815,CVE-2019-14816.
Signed-off-by: Wen Huang <huangwenabc@gmail.com>
Acked-by: Ganapathi Bhat <gbhat@marvell.comg>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MT7630E hardware does support 5GHz, but we do not properly configure phy
for 5GHz channels. Scanning at this band not only do not show any APs
but also can hang the firmware.
Since vendor reference driver do not support 5GHz we don't know how
properly configure 5GHz channels. So disable this band for MT7630E .
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 41634aa8d6 ("mt76: only schedule txqs from the tx tasklet")
I can observe firmware hangs on MT7630E on station mode: tx stop
functioning after minor activity (rx keep working) and on module
unload device fail to stop with messages:
[ 5446.141413] mt76x0e 0000:06:00.0: TX DMA did not stop
[ 5449.176764] mt76x0e 0000:06:00.0: TX DMA did not stop
Loading module again results in failure to associate with AP.
Only machine power off / power on cycle can make device work again.
It's unclear why commit 41634aa8d6 causes the problem, but it is
related to HW encryption. Since issue is a firmware hang, that is super
hard to debug, just disable HW encryption as fix for the issue.
Fixes: 41634aa8d6 ("mt76: only schedule txqs from the tx tasklet")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Global pages support is removed from VT-d spec 3.0. Since global pages G
flag only affects first-level paging structures and because DMA request
with PASID are only supported by VT-d spec. 3.0 and onward, we can
safely remove global pages support.
For kernel shared virtual address IOTLB invalidation, PASID
granularity and page selective within PASID will be used. There is
no global granularity supported. Without this fix, IOTLB invalidation
will cause invalid descriptor error in the queued invalidation (QI)
interface.
Fixes: 1c4f88b7f1 ("iommu/vt-d: Shared virtual address in scalable mode")
Reported-by: Sanjay K Kumar <sanjay.k.kumar@intel.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
do_sched_cfs_period_timer() will refill cfs_b runtime and call
distribute_cfs_runtime to unthrottle cfs_rq, sometimes cfs_b->runtime
will allocate all quota to one cfs_rq incorrectly, then other cfs_rqs
attached to this cfs_b can't get runtime and will be throttled.
We find that one throttled cfs_rq has non-negative
cfs_rq->runtime_remaining and cause an unexpetced cast from s64 to u64
in snippet:
distribute_cfs_runtime() {
runtime = -cfs_rq->runtime_remaining + 1;
}
The runtime here will change to a large number and consume all
cfs_b->runtime in this cfs_b period.
According to Ben Segall, the throttled cfs_rq can have
account_cfs_rq_runtime called on it because it is throttled before
idle_balance, and the idle_balance calls update_rq_clock to add time
that is accounted to the task.
This commit prevents cfs_rq to be assgined new runtime if it has been
throttled until that distribute_cfs_runtime is called.
Signed-off-by: Liangyan <liangyan.peng@linux.alibaba.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Valentin Schneider <valentin.schneider@arm.com>
Reviewed-by: Ben Segall <bsegall@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: shanpeic@linux.alibaba.com
Cc: stable@vger.kernel.org
Cc: xlpang@linux.alibaba.com
Fixes: d3d9dc3302 ("sched: Throttle entities exceeding their allowed bandwidth")
Link: https://lkml.kernel.org/r/20190826121633.6538-1-liangyan.peng@linux.alibaba.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Original pin node values of ASUS UX431FL with ALC294:
0x12 0xb7a60140
0x13 0x40000000
0x14 0x90170110
0x15 0x411111f0
0x16 0x411111f0
0x17 0x90170111
0x18 0x411111f0
0x19 0x411111f0
0x1a 0x411111f0
0x1b 0x411111f0
0x1d 0x4066852d
0x1e 0x411111f0
0x1f 0x411111f0
0x21 0x04211020
1. Has duplicated internal speakers (0x14 & 0x17) which makes the output
route become confused. So, the output volume cannot be changed by
setting.
2. Misses the headset mic pin node.
This patch disables the confusing speaker (NID 0x14) and enables the
headset mic (NID 0x19).
Link: https://lore.kernel.org/r/20190902100054.6941-1-jian-hong@endlessm.com
Signed-off-by: Jian-Hong Pan <jian-hong@endlessm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
