This is in preparation for zstd compression levels. As each level will
require different size of workspace, workspaces_list is no longer a
really fitting name.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
It is very easy to miss places that rely on a certain bitshifting for
decoding the type_level overloading. Add helpers to do this instead.
Cc: Omar Sandoval <osandov@osandov.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The typos accumulate over time so once in a while time they get fixed in
a large patch.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
When using a 'var & (PAGE_SIZE - 1)' construct one is checking for a page
alignment and thus should use the PAGE_ALIGNED() macro instead of
open-coding it.
Convert all open-coded occurrences of PAGE_ALIGNED().
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Constructs like 'var & (PAGE_SIZE - 1)' or 'var & ~PAGE_MASK' can denote an
offset into a page.
So replace them by the offset_in_page() macro instead of open-coding it if
they're not used as an alignment check.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This function really checks whether adding more data to the bio will
straddle a stripe/chunk. So first let's give it a more appropraite name
- btrfs_bio_fits_in_stripe. Secondly, the offset parameter was never
used to just remove it. Thirdly, pages are submitted to either btree or
data inodes so it's guaranteed that tree->ops is set so replace the
check with an ASSERT. Finally, document the parameters of the function.
No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This parameter was never used, yet was part of the interface of the
function ever since its introduction as extent_io_ops::writepage_end_io_hook
in e6dcd2dc9c ("Btrfs: New data=ordered implementation"). Now that
NULL is passed everywhere as a value for this parameter let's remove it
for good. No functional changes.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
This callback is ony ever called for data page writeout so there is no
need to actually abstract it via extent_io_ops. Lets just export it,
remove the definition of the callback and call it directly in the
functions that invoke the callback. Also rename the function to
btrfs_writepage_endio_finish_ordered since what it really does is
account finished io in the ordered extent data structures. No
functional changes.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Pull XArray conversion from Matthew Wilcox:
"The XArray provides an improved interface to the radix tree data
structure, providing locking as part of the API, specifying GFP flags
at allocation time, eliminating preloading, less re-walking the tree,
more efficient iterations and not exposing RCU-protected pointers to
its users.
This patch set
1. Introduces the XArray implementation
2. Converts the pagecache to use it
3. Converts memremap to use it
The page cache is the most complex and important user of the radix
tree, so converting it was most important. Converting the memremap
code removes the only other user of the multiorder code, which allows
us to remove the radix tree code that supported it.
I have 40+ followup patches to convert many other users of the radix
tree over to the XArray, but I'd like to get this part in first. The
other conversions haven't been in linux-next and aren't suitable for
applying yet, but you can see them in the xarray-conv branch if you're
interested"
* 'xarray' of git://git.infradead.org/users/willy/linux-dax: (90 commits)
radix tree: Remove multiorder support
radix tree test: Convert multiorder tests to XArray
radix tree tests: Convert item_delete_rcu to XArray
radix tree tests: Convert item_kill_tree to XArray
radix tree tests: Move item_insert_order
radix tree test suite: Remove multiorder benchmarking
radix tree test suite: Remove __item_insert
memremap: Convert to XArray
xarray: Add range store functionality
xarray: Move multiorder_check to in-kernel tests
xarray: Move multiorder_shrink to kernel tests
xarray: Move multiorder account test in-kernel
radix tree test suite: Convert iteration test to XArray
radix tree test suite: Convert tag_tagged_items to XArray
radix tree: Remove radix_tree_clear_tags
radix tree: Remove radix_tree_maybe_preload_order
radix tree: Remove split/join code
radix tree: Remove radix_tree_update_node_t
page cache: Finish XArray conversion
dax: Convert page fault handlers to XArray
...
Pointer 'tree' is being assigned but is never used hence it is redundant
and can be removed. This is a leftover from cleanup patch
00032d38ea ("btrfs: drop extent_io_ops::merge_bio_hook
callback").
Cleans up clang warning:
warning: variable 'tree' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Introduce xarray value entries and tagged pointers to replace radix
tree exceptional entries. This is a slight change in encoding to allow
the use of an extra bit (we can now store BITS_PER_LONG - 1 bits in a
value entry). It is also a change in emphasis; exceptional entries are
intimidating and different. As the comment explains, you can choose
to store values or pointers in the xarray and they are both first-class
citizens.
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Josef Bacik <jbacik@fb.com>
The data and metadata callback implementation both use the same
function. We can remove the call indirection completely.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Use the wrappers and reduce the amount of low-level details about the
waitqueue management.
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=I0y0
-----END PGP SIGNATURE-----
Merge tag 'for-4.17-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull more btrfs updates from David Sterba:
"We have queued a few more fixes (error handling, log replay,
softlockup) and the rest is SPDX updates that touche almost all files
so the diffstat is long"
* tag 'for-4.17-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: Only check first key for committed tree blocks
btrfs: add SPDX header to Kconfig
btrfs: replace GPL boilerplate by SPDX -- sources
btrfs: replace GPL boilerplate by SPDX -- headers
Btrfs: fix loss of prealloc extents past i_size after fsync log replay
Btrfs: clean up resources during umount after trans is aborted
btrfs: Fix possible softlock on single core machines
Btrfs: bail out on error during replay_dir_deletes
Btrfs: fix NULL pointer dereference in log_dir_items
Remove GPL boilerplate text (long, short, one-line) and keep the rest,
ie. personal, company or original source copyright statements. Add the
SPDX header.
Signed-off-by: David Sterba <dsterba@suse.com>
Remove the address_space ->tree_lock and use the xa_lock newly added to
the radix_tree_root. Rename the address_space ->page_tree to ->i_pages,
since we don't really care that it's a tree.
[willy@infradead.org: fix nds32, fs/dax.c]
Link: http://lkml.kernel.org/r/20180406145415.GB20605@bombadil.infradead.orgLink: http://lkml.kernel.org/r/20180313132639.17387-9-willy@infradead.org
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Cc: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The __cold functions are placed to a special section, as they're
expected to be called rarely. This could help i-cache prefetches or help
compiler to decide which branches are more/less likely to be taken
without any other annotations needed.
Though we can't add more __exit annotations, it's still possible to add
__cold (that's also added with __exit). That way the following function
categories are tagged:
- printf wrappers, error messages
- exit helpers
Signed-off-by: David Sterba <dsterba@suse.com>
-----BEGIN PGP SIGNATURE-----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=Irul
-----END PGP SIGNATURE-----
Merge tag 'for-4.16-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs updates from David Sterba:
"Features or user visible changes:
- fallocate: implement zero range mode
- avoid losing data raid profile when deleting a device
- tree item checker: more checks for directory items and xattrs
Notable fixes:
- raid56 recovery: don't use cached stripes, that could be
potentially changed and a later RMW or recovery would lead to
corruptions or failures
- let raid56 try harder to rebuild damaged data, reading from all
stripes if necessary
- fix scrub to repair raid56 in a similar way as in the case above
Other:
- cleanups: device freeing, removed some call indirections, redundant
bio_put/_get, unused parameters, refactorings and renames
- RCU list traversal fixups
- simplify mount callchain, remove recursing back when mounting a
subvolume
- plug for fsync, may improve bio merging on multiple devices
- compression heurisic: replace heap sort with radix sort, gains some
performance
- add extent map selftests, buffered write vs dio"
* tag 'for-4.16-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: (155 commits)
btrfs: drop devid as device_list_add() arg
btrfs: get device pointer from device_list_add()
btrfs: set the total_devices in device_list_add()
btrfs: move pr_info into device_list_add
btrfs: make btrfs_free_stale_devices() to match the path
btrfs: rename btrfs_free_stale_devices() arg to skip_dev
btrfs: make btrfs_free_stale_devices() argument optional
btrfs: make btrfs_free_stale_device() to iterate all stales
btrfs: no need to check for btrfs_fs_devices::seeding
btrfs: Use IS_ALIGNED in btrfs_truncate_block instead of opencoding it
Btrfs: noinline merge_extent_mapping
Btrfs: add WARN_ONCE to detect unexpected error from merge_extent_mapping
Btrfs: extent map selftest: dio write vs dio read
Btrfs: extent map selftest: buffered write vs dio read
Btrfs: add extent map selftests
Btrfs: move extent map specific code to extent_map.c
Btrfs: add helper for em merge logic
Btrfs: fix unexpected EEXIST from btrfs_get_extent
Btrfs: fix incorrect block_len in merge_extent_mapping
btrfs: Remove unused readahead spinlock
...
bio_get/set is necessary only if the bio is going to be referenced
following submissions. In the code paths where such calls are made
we don't really need them since the bio is referenced only if
btrfs_map_bio returns an error. And this function can return an error
prior to submission only. So referencing the bio is safe. Furthermore
we do call bio_endio which will consume the last reference. So let's
remove the redundant calls.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
As it's a single instance and local to the file, we don't need to pass
it as an argument.
Reviewed-by: Timofey Titovets <nefelim4ag@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The callback is trivial and we don't need the abstraction for our
purposes. Let's open code it.
Reviewed-by: Timofey Titovets <nefelim4ag@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The callback is trivial and we don't need the abstraction for our
purposes. Let's open code it and also make the array types explicit.
Reviewed-by: Timofey Titovets <nefelim4ag@gmail.com>
Signed-off-by: David Sterba <dsterba@suse.com>
There are several places opencoding this conversion, add a helper now
that we have 3 compression algorithms.
Signed-off-by: David Sterba <dsterba@suse.com>
Slowest part of heuristic for now is kernel heap sort()
It's can take up to 55% of runtime on sorting bucket items.
As sorting will always call on most data sets to get correctly
byte_core_set_size, the only way to speed up heuristic, is to
speed up sort on bucket.
Add a general radix_sort function.
Radix sort require 2 buffers, one full size of input array
and one for store counters (jump addresses).
That increase usage per heuristic workspace +1KiB
8KiB + 1KiB -> 8KiB + 2KiB
That is LSD Radix, i use 4 bit as a base for calculating,
to make counters array acceptable small (16 elements * 8 byte).
That Radix sort implementation have several points to adjust,
I added him to make radix sort general usable in kernel,
like heap sort, if needed.
Performance tested in userspace copy of heuristic code,
throughput:
- average <-> random data: ~3500 MiB/s - heap sort
- average <-> random data: ~6000 MiB/s - radix sort
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
[ coding style fixes ]
Signed-off-by: David Sterba <dsterba@suse.com>
This patch converts 3 users to bio_last_bvec_all(), so that we can go
ahead and convert to multipage bvec.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch converts to bio_first_bvec_all() & bio_first_page_all() for
retrieving the 1st bvec/page, and prepares for supporting multipage bvec.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
[BUG]
Kernel panic when mounting with "-o compress" mount option.
KASAN will report like:
------
==================================================================
BUG: KASAN: wild-memory-access in strncmp+0x31/0xc0
Read of size 1 at addr d86735fce994f800 by task mount/662
...
Call Trace:
dump_stack+0xe3/0x175
kasan_report+0x163/0x370
__asan_load1+0x47/0x50
strncmp+0x31/0xc0
btrfs_compress_str2level+0x20/0x70 [btrfs]
btrfs_parse_options+0xff4/0x1870 [btrfs]
open_ctree+0x2679/0x49f0 [btrfs]
btrfs_mount+0x1b7f/0x1d30 [btrfs]
mount_fs+0x49/0x190
vfs_kern_mount.part.29+0xba/0x280
vfs_kern_mount+0x13/0x20
btrfs_mount+0x31e/0x1d30 [btrfs]
mount_fs+0x49/0x190
vfs_kern_mount.part.29+0xba/0x280
do_mount+0xaad/0x1a00
SyS_mount+0x98/0xe0
entry_SYSCALL_64_fastpath+0x1f/0xbe
------
[Cause]
For 'compress' and 'compress_force' options, its token doesn't expect
any parameter so its args[0] contains uninitialized data.
Accessing args[0] will cause above wild memory access.
[Fix]
For Opt_compress and Opt_compress_force, set compression level to
the default.
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ set the default in advance ]
Signed-off-by: David Sterba <dsterba@suse.com>
Compression code path has only flaged bios with REQ_OP_WRITE no matter
where the bios come from, but it could be a sync write if fsync starts
this writeback or a normal writeback write if wb kthread starts a
periodic writeback.
It breaks the rule that sync writes and writeback writes need to be
differentiated from each other, because from the POV of block layer,
all bios need to be recognized by these flags in order to do some
management, e.g. throttlling.
This passes writeback_control to compression write path so that it can
send bios with proper flags to block layer.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Byte distribution check in heuristic will filter edge data cases and
some time fail to classify input data.
Let's fix that by adding Shannon entropy calculation, that will cover
classification of most other data types.
As Shannon entropy needs log2 with some precision to work, let's use
ilog2(N) and for increased precision, by do ilog2(pow(N, 4)).
Shannon entropy has been slightly changed to avoid signed numbers and
division.
The calculation is direct by the formula, successor of precalculated
table or chains of if-else.
The accuracy errors of ilog2 are compensated by
@ENTROPY_LVL_ACEPTABLE 70 -> 65
@ENTROPY_LVL_HIGH 85 -> 80
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update comments ]
Signed-off-by: David Sterba <dsterba@suse.com>
Calculate byte core set for data sample:
- sort buckets' numbers in decreasing order
- count how many values cover 90% of the sample
If the core set size is low (<=25%), data are easily compressible.
If the core set size is high (>=80%), data are not compressible.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update comments ]
Signed-off-by: David Sterba <dsterba@suse.com>
Calculate byte set size for data sample:
- calculate how many unique bytes have been in the sample
- for all bytes count > 0, check if we're still in the low count range
(~25%), such data are easily compressible, otherwise furhter analysis
is needed
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update comments ]
Signed-off-by: David Sterba <dsterba@suse.com>
Walk over data sample and use memcmp to detect repeated patterns, like
zeros, but a bit more general.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ minor coding style fixes ]
Signed-off-by: David Sterba <dsterba@suse.com>
Copy sample data from the input data range to sample buffer then
calculate byte value count for that sample into bucket.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
[ minor comment updates ]
Signed-off-by: David Sterba <dsterba@suse.com>
Add basic defines and structures for data sampling.
Added macros:
- For future sampling algo
- For bucket size
Heuristic workspace:
- Add bucket for storing byte type counters
- Add sample array for storing partial copy of input data range
- Add counter for store current sample size to workspace
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ minor coding style fixes, comments updated ]
Signed-off-by: David Sterba <dsterba@suse.com>
Compression heuristic itself is not a compression type, as current
infrastructure provides workspaces for several compression types, it's
difficult to just add heuristic workspace.
Just refactor the code to support compression/heuristic workspaces with
maximum code sharing and minimum changes in it.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ coding style fixes ]
Signed-off-by: David Sterba <dsterba@suse.com>
This is bikeshedding, but it seems people are drastically more likely to
understand "zlib:9" as compression level rather than an algorithm
version compared to "zlib9".
Based on feedback on the mailinglist, the ":9" will be the only accepted
syntax. The level must be a single digit. Unrecognized format will
result to the default, for forward compatibility in a similar way the
compression algorithm specifier was relaxed in commit
a7164fa4e0 ("btrfs: prepare for extensions in compression
options").
Signed-off-by: Adam Borowski <kilobyte@angband.pl>
Reviewed-by: David Sterba <dsterba@suse.com>
[ tighten the accepted format ]
Signed-off-by: David Sterba <dsterba@suse.com>
Preliminary support for setting compression level for zlib, the
following works:
$ mount -o compess=zlib # default
$ mount -o compess=zlib0 # same
$ mount -o compess=zlib9 # level 9, slower sync, less data
$ mount -o compess=zlib1 # level 1, faster sync, more data
$ mount -o remount,compress=zlib3 # level set by remount
The compress-force works the same as compress'. The level is visible in
the same format in /proc/mounts. Level set via file property does not
work yet.
Required patch: "btrfs: prepare for extensions in compression options"
Signed-off-by: David Sterba <dsterba@suse.com>
At few places we could use BLK_STS_OK and BLK_STS_NOSUPP.
Signed-off-by: Anand Jain <anand.jain@oracle.com>
Reviewed-by: Satoru Taekeuchi <satoru.takeuchi@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ dropped first hunk btrfs_endio_direct_read ]
Signed-off-by: David Sterba <dsterba@suse.com>
Pull btrfs fixes from David Sterba:
"We've collected a bunch of isolated fixes, for crashes, user-visible
behaviour or missing bits from other subsystem cleanups from the past.
The overall number is not small but I was not able to make it
significantly smaller. Most of the patches are supposed to go to
stable"
* 'for-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: log csums for all modified extents
Btrfs: fix unexpected result when dio reading corrupted blocks
btrfs: Report error on removing qgroup if del_qgroup_item fails
Btrfs: skip checksum when reading compressed data if some IO have failed
Btrfs: fix kernel oops while reading compressed data
Btrfs: use btrfs_op instead of bio_op in __btrfs_map_block
Btrfs: do not backup tree roots when fsync
btrfs: remove BTRFS_FS_QUOTA_DISABLING flag
btrfs: propagate error to btrfs_cmp_data_prepare caller
btrfs: prevent to set invalid default subvolid
Btrfs: send: fix error number for unknown inode types
btrfs: fix NULL pointer dereference from free_reloc_roots()
btrfs: finish ordered extent cleaning if no progress is found
btrfs: clear ordered flag on cleaning up ordered extents
Btrfs: fix incorrect {node,sector}size endianness from BTRFS_IOC_FS_INFO
Btrfs: do not reset bio->bi_ops while writing bio
Btrfs: use the new helper wbc_to_write_flags
Currently even if the underlying disk reports failure on IO,
compressed read endio still gets to verify checksum and reports it as
a checksum error.
In fact, if some IO have failed during reading a compressed data
extent , there's no way the checksum could match, therefore, we can
skip that in order to return error quickly to the upper layer.
Please note that we need to do this after recording the failed mirror
index so that read-repair in the upper layer's endio can work
properly.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Tested-by: Paul Jones <paul@pauljones.id.au>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The kernel oops happens at
kernel BUG at fs/btrfs/extent_io.c:2104!
...
RIP: clean_io_failure+0x263/0x2a0 [btrfs]
It's showing that read-repair code is using an improper mirror index.
This is due to the fact that compression read's endio hasn't recorded
the failed mirror index in %cb->orig_bio.
With this, btrfs's read-repair can work properly on reading compressed
data.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reported-by: Paul Jones <paul@pauljones.id.au>
Tested-by: Paul Jones <paul@pauljones.id.au>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Pull zstd support from Chris Mason:
"Nick Terrell's patch series to add zstd support to the kernel has been
floating around for a while. After talking with Dave Sterba, Herbert
and Phillip, we decided to send the whole thing in as one pull
request.
zstd is a big win in speed over zlib and in compression ratio over
lzo, and the compression team here at FB has gotten great results
using it in production. Nick will continue to update the kernel side
with new improvements from the open source zstd userland code.
Nick has a number of benchmarks for the main zstd code in his lib/zstd
commit:
I ran the benchmarks on a Ubuntu 14.04 VM with 2 cores and 4 GiB
of RAM. The VM is running on a MacBook Pro with a 3.1 GHz Intel
Core i7 processor, 16 GB of RAM, and a SSD. I benchmarked using
`silesia.tar` [3], which is 211,988,480 B large. Run the following
commands for the benchmark:
sudo modprobe zstd_compress_test
sudo mknod zstd_compress_test c 245 0
sudo cp silesia.tar zstd_compress_test
The time is reported by the time of the userland `cp`.
The MB/s is computed with
1,536,217,008 B / time(buffer size, hash)
which includes the time to copy from userland.
The Adjusted MB/s is computed with
1,536,217,088 B / (time(buffer size, hash) - time(buffer size, none)).
The memory reported is the amount of memory the compressor
requests.
| Method | Size (B) | Time (s) | Ratio | MB/s | Adj MB/s | Mem (MB) |
|----------|----------|----------|-------|---------|----------|----------|
| none | 11988480 | 0.100 | 1 | 2119.88 | - | - |
| zstd -1 | 73645762 | 1.044 | 2.878 | 203.05 | 224.56 | 1.23 |
| zstd -3 | 66988878 | 1.761 | 3.165 | 120.38 | 127.63 | 2.47 |
| zstd -5 | 65001259 | 2.563 | 3.261 | 82.71 | 86.07 | 2.86 |
| zstd -10 | 60165346 | 13.242 | 3.523 | 16.01 | 16.13 | 13.22 |
| zstd -15 | 58009756 | 47.601 | 3.654 | 4.45 | 4.46 | 21.61 |
| zstd -19 | 54014593 | 102.835 | 3.925 | 2.06 | 2.06 | 60.15 |
| zlib -1 | 77260026 | 2.895 | 2.744 | 73.23 | 75.85 | 0.27 |
| zlib -3 | 72972206 | 4.116 | 2.905 | 51.50 | 52.79 | 0.27 |
| zlib -6 | 68190360 | 9.633 | 3.109 | 22.01 | 22.24 | 0.27 |
| zlib -9 | 67613382 | 22.554 | 3.135 | 9.40 | 9.44 | 0.27 |
I benchmarked zstd decompression using the same method on the same
machine. The benchmark file is located in the upstream zstd repo
under `contrib/linux-kernel/zstd_decompress_test.c` [4]. The
memory reported is the amount of memory required to decompress
data compressed with the given compression level. If you know the
maximum size of your input, you can reduce the memory usage of
decompression irrespective of the compression level.
| Method | Time (s) | MB/s | Adjusted MB/s | Memory (MB) |
|----------|----------|---------|---------------|-------------|
| none | 0.025 | 8479.54 | - | - |
| zstd -1 | 0.358 | 592.15 | 636.60 | 0.84 |
| zstd -3 | 0.396 | 535.32 | 571.40 | 1.46 |
| zstd -5 | 0.396 | 535.32 | 571.40 | 1.46 |
| zstd -10 | 0.374 | 566.81 | 607.42 | 2.51 |
| zstd -15 | 0.379 | 559.34 | 598.84 | 4.61 |
| zstd -19 | 0.412 | 514.54 | 547.77 | 8.80 |
| zlib -1 | 0.940 | 225.52 | 231.68 | 0.04 |
| zlib -3 | 0.883 | 240.08 | 247.07 | 0.04 |
| zlib -6 | 0.844 | 251.17 | 258.84 | 0.04 |
| zlib -9 | 0.837 | 253.27 | 287.64 | 0.04 |
I ran a long series of tests and benchmarks on the btrfs side and the
gains are very similar to the core benchmarks Nick ran"
* 'zstd-minimal' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
squashfs: Add zstd support
btrfs: Add zstd support
lib: Add zstd modules
lib: Add xxhash module
Add skeleton code for compresison heuristics. Now it iterates over all
the pages, but in the end always says "yes, compress please", ie it does
not change the current behaviour.
In the future we're going to add various heuristics to analyze the data.
This patch can be used as a baseline for measuring if the effectivness
and performance.
Signed-off-by: Timofey Titovets <nefelim4ag@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ enhanced changelog, modified comments ]
Signed-off-by: David Sterba <dsterba@suse.com>
find_workspace() allocates up to num_online_cpus() + 1 workspaces.
free_workspace() will only keep num_online_cpus() workspaces. When
(de)compressing we will allocate num_online_cpus() + 1 workspaces, then
free one, and repeat. Instead, we can just keep num_online_cpus() + 1
workspaces around, and never have to allocate/free another workspace in the
common case.
I tested on a Ubuntu 14.04 VM with 2 cores and 4 GiB of RAM. I mounted a
BtrFS partition with -o compress-force={lzo,zlib,zstd} and logged whenever
a workspace was allocated of freed. Then I copied vmlinux (527 MB) to the
partition. Before the patch, during the copy it would allocate and free 5-6
workspaces. After, it only allocated the initial 3. This held true for lzo,
zlib, and zstd. The time it took to execute cp vmlinux /mnt/btrfs && sync
dropped from 1.70s to 1.44s with lzo compression, and from 2.04s to 1.80s
for zstd compression.
Signed-off-by: Nick Terrell <terrelln@fb.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Add zstd compression and decompression support to BtrFS. zstd at its
fastest level compresses almost as well as zlib, while offering much
faster compression and decompression, approaching lzo speeds.
I benchmarked btrfs with zstd compression against no compression, lzo
compression, and zlib compression. I benchmarked two scenarios. Copying
a set of files to btrfs, and then reading the files. Copying a tarball
to btrfs, extracting it to btrfs, and then reading the extracted files.
After every operation, I call `sync` and include the sync time.
Between every pair of operations I unmount and remount the filesystem
to avoid caching. The benchmark files can be found in the upstream
zstd source repository under
`contrib/linux-kernel/{btrfs-benchmark.sh,btrfs-extract-benchmark.sh}`
[1] [2].
I ran the benchmarks on a Ubuntu 14.04 VM with 2 cores and 4 GiB of RAM.
The VM is running on a MacBook Pro with a 3.1 GHz Intel Core i7 processor,
16 GB of RAM, and a SSD.
The first compression benchmark is copying 10 copies of the unzipped
Silesia corpus [3] into a BtrFS filesystem mounted with
`-o compress-force=Method`. The decompression benchmark times how long
it takes to `tar` all 10 copies into `/dev/null`. The compression ratio is
measured by comparing the output of `df` and `du`. See the benchmark file
[1] for details. I benchmarked multiple zstd compression levels, although
the patch uses zstd level 1.
| Method | Ratio | Compression MB/s | Decompression speed |
|---------|-------|------------------|---------------------|
| None | 0.99 | 504 | 686 |
| lzo | 1.66 | 398 | 442 |
| zlib | 2.58 | 65 | 241 |
| zstd 1 | 2.57 | 260 | 383 |
| zstd 3 | 2.71 | 174 | 408 |
| zstd 6 | 2.87 | 70 | 398 |
| zstd 9 | 2.92 | 43 | 406 |
| zstd 12 | 2.93 | 21 | 408 |
| zstd 15 | 3.01 | 11 | 354 |
The next benchmark first copies `linux-4.11.6.tar` [4] to btrfs. Then it
measures the compression ratio, extracts the tar, and deletes the tar.
Then it measures the compression ratio again, and `tar`s the extracted
files into `/dev/null`. See the benchmark file [2] for details.
| Method | Tar Ratio | Extract Ratio | Copy (s) | Extract (s)| Read (s) |
|--------|-----------|---------------|----------|------------|----------|
| None | 0.97 | 0.78 | 0.981 | 5.501 | 8.807 |
| lzo | 2.06 | 1.38 | 1.631 | 8.458 | 8.585 |
| zlib | 3.40 | 1.86 | 7.750 | 21.544 | 11.744 |
| zstd 1 | 3.57 | 1.85 | 2.579 | 11.479 | 9.389 |
[1] https://github.com/facebook/zstd/blob/dev/contrib/linux-kernel/btrfs-benchmark.sh
[2] https://github.com/facebook/zstd/blob/dev/contrib/linux-kernel/btrfs-extract-benchmark.sh
[3] http://sun.aei.polsl.pl/~sdeor/index.php?page=silesia
[4] https://cdn.kernel.org/pub/linux/kernel/v4.x/linux-4.11.6.tar.xz
zstd source repository: https://github.com/facebook/zstd
Signed-off-by: Nick Terrell <terrelln@fb.com>
Signed-off-by: Chris Mason <clm@fb.com>
Pull btrfs fixes from David Sterba:
"We've identified and fixed a silent corruption (introduced by code in
the first pull), a fixup after the blk_status_t merge and two fixes to
incremental send that Filipe has been hunting for some time"
* 'for-4.13-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
Btrfs: fix unexpected return value of bio_readpage_error
btrfs: btrfs_create_repair_bio never fails, skip error handling
btrfs: cloned bios must not be iterated by bio_for_each_segment_all
Btrfs: fix write corruption due to bio cloning on raid5/6
Btrfs: incremental send, fix invalid memory access
Btrfs: incremental send, fix invalid path for link commands
We've started using cloned bios more in 4.13, there are some specifics
regarding the iteration. Filipe found [1] that the raid56 iterated a
cloned bio using bio_for_each_segment_all, which is incorrect. The
cloned bios have wrong bi_vcnt and this could lead to silent
corruptions. This patch adds assertions to all remaining
bio_for_each_segment_all cases.
[1] https://patchwork.kernel.org/patch/9838535/
Reviewed-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>