This patch introduces a sysfs group entry for the UFS attributes. The
group adds "attributes" folder under the UFS driver sysfs entry
(/sys/bus/platform/drivers/ufshcd/*). The attributes are shown
as hexadecimal numbers. The full information about the attributes could
be found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS flags. The group adds
"flags" folder under the UFS driver sysfs entry
(/sys/bus/platform/drivers/ufshcd/*). The flags are shown as boolean value
("true" or "false"). The full information about the UFS flags could be
found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS unit descriptor
parameters. The group adds "unit_descriptor" folder under the corresponding
SCSI device sysfs entry (/sys/class/scsi_device/*/device/). The parameters
are shown as hexadecimal numbers. The full information about the parameters
could be found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS health descriptor
parameters. The group adds "health_descriptor" folder under the UFS driver
sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The parameters are shown
as hexadecimal numbers. The full information about the parameters could be
found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS geometry descriptor
parameters. The group adds "geometry_descriptor" folder under the UFS
driver sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The parameters
are shown as hexadecimal numbers. The full information about the parameters
could be found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS interconnect
descriptor parameters. The group adds "interconnect_descriptor" folder
under the UFS driver sysfs entry (/sys/bus/platform/drivers/ufshcd/*).
The parameters are shown as hexadecimal numbers. The full information
about the parameters could be found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS device descriptor
parameters. The group adds "device_descriptor" folder under the UFS driver
sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The parameters are shown
as hexadecimal numbers. The full information about the parameters could be
found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since in UFS 2.1 specification some of the descriptor lengths differs
from 2.0 specification and some devices, which are reporting spec
version 2.0 have different descriptor lengths we can not rely on
hardcoded values taken from 2.0 specification. This patch introduces
reading these lengths per each device from descriptor headers at probe
time to ensure their correctness.
Signed-off-by: Michal' Potomski <michalx.potomski@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull device descriptor reading out of ufs quirk so it can be used also
for other purposes.
Revamp the fixup setup:
1. Rename ufs_device_info to ufs_dev_desc as very similar name
ufs_dev_info is already in use.
2. Make the handlers static as they are not used out of the ufshdc.c
file.
[mkp: applied by hand]
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
According to JESD220B - UFS v2.0, the maximum size of device descriptor
has changed from 0x1F to 0x40. This patch updates the maximum size of
this descriptor.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In this change there are a few fixes of possible NULL pointer access and
possible access to index that exceeds array boundaries.
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When any UFS host controller receives a TM(Task Management) response
from a UFS device, UFS driver has been recognize like receiving a
message of "Task Management Function Complete"(00h) in all cases, so
far. That means there is no pending task for a tag of the TM request
sent before in the UFS device. That's because the byte offset 6 in TM
response which has been used to get a TM service response so far
represents just whether or not a TM transmission passes.
Regarding UFS spec, the correct byte offset to get TM service response
is 15, not 6.
I tested that UFS driver responds properly for the TM response from a
UFS device with an reference board with exynos8890, as follow: No
pending task -> Task Management Function Complete (00h) Pending task ->
Task Management Function Succeeded (08h)
[mkp: applied by hand]
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: HeonGwang Chu <hg.chu@samsung.com>
Tested-by: : Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Some UFS devices don't require VCCQ rail for device operations hence
this change adds support to recognize such devices and remove vote for
the unused VCCQ rail.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently we use the host quirks mechanism in order to
handle both device and host controller quirks.
In order to support various of UFS devices we should separate
handling the device quirks from the host controller's.
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This change adds support to read device descriptor and string descriptor
from a UFS device
Reviewed-by: Gilad Broner <gbroner@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
QUERY_DESC_GEOMETRY_MAZ_SIZE
QUERY_DESC_GEOMETRY_MAX_SIZE
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for UFS device and UniPro link power management
during runtime/system PM.
Main idea is to define multiple UFS low power levels based on UFS device
and UFS link power states. This would allow any specific platform or pci
driver to choose the best suited low power level during runtime and
system suspend based on their power goals.
bkops handlig:
To put the UFS device in sleep state when bkops is disabled, first query
the bkops status from the device and enable bkops on device only if
device needs time to perform the bkops.
START_STOP handling:
Before sending START_STOP_UNIT to the device well-known logical unit
(w-lun) to make sure that the device w-lun unit attention condition is
cleared.
Write protection:
UFS device specification allows LUs to be write protected, either
permanently or power on write protected. If any LU is power on write
protected and if the card is power cycled (by powering off VCCQ and/or
VCC rails), LU's write protect status would be lost. So this means those
LUs can be written now. To ensures that UFS device is power cycled only
if the power on protect is not set for any of the LUs, check if power on
write protect is set and if device is in sleep/power-off state & link in
inactive state (Hibern8 or OFF state).
If none of the Logical Units on UFS device is power on write protected
then all UFS device power rails (VCC, VCCQ & VCCQ2) can be turned off if
UFS device is in power-off state and UFS link is in OFF state. But current
implementation would disable all device power rails even if UFS link is
not in OFF state.
Low power mode:
If UFS link is in OFF state then UFS host controller can be power collapsed
to avoid leakage current from it. Note that if UFS host controller is power
collapsed, full UFS reinitialization will be required on resume to
re-establish the link between host and device.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
UFS device may have standard LUs and LUN id could be from 0x00 to 0x7F.
UFS device specification use "Peripheral Device Addressing Format"
(SCSI SAM-5) for standard LUs.
UFS device may also have the Well Known LUs (also referred as W-LU) which
again could be from 0x00 to 0x7F. For W-LUs, UFS device specification only
allows the "Extended Addressing Format" (SCSI SAM-5) which means the W-LUNs
would start from 0xC100 onwards.
This means max. LUN number reported from UFS device could be 0xC17F hence
this patch advertise the "max_lun" as 0xC17F which will allow SCSI mid
layer to detect the W-LUs as well.
But once the W-LUs are detected, UFSHCD driver may get the commands with
SCSI LUN id upto 0xC17F but UPIU LUN id field is only 8-bit wide so it
requires the mapping of SCSI LUN id to UPIU LUN id. This patch also add
support for this mapping.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The maximum power consumption in active is determined by bActiveICCLevel.
The configuration is done by reading max current supported by the
regulators connected to VCC, VCCQ and VCCQ2 rails on the boards, and
reading the current consumption levels from the device for each rails
(vcc/vccq/vccq2) using power descriptor.
We configure the bActiveICCLevel attribute, with the max value that
correspond to the minimum-of(VCC-current-level,VCCQ-current-level,
VCCQ2-current-level).
In order to minimize resume latency, pre-fetch icc levels and reference
clock during initialization and avoid reading them each link startup
during resume.
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently reading query descriptor is more tightened to each
descriptor type. This patch generalize the approach and allows
reading any parameter from any query descriptor.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add the support for voting of the regulator powering the
host controller logic.
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
UFS devices are powered by at most three external power supplies -
- VCC - The flash memory core power supply, 2.7V to 3.6V or 1.70V to 1.95V
- VCCQ - The controller and I/O power supply, 1.1V to 1.3V
- VCCQ2 - Secondary controller and/or I/O power supply, 1.65V to 1.95V
For some devices VCCQ or VCCQ2 are optional as they can be
generated using internal LDO inside the UFS device.
Add DT bindings for voltage regulators that can be controlled
from host driver.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some of the UFS devices may support different number of commands
that can be queued per LU. At the current implementation,
SW configure each of the UFS devices LU's according to the
controller capability.
In this patch the queue depth available per LU is read and updated in
the LU's SW structure.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Introduces the API for sending queries with descriptors.
A descriptor is a block or page of parameters that describe the device.
The descriptors are classified into types and can range in size
from 2 bytes through 255 bytes.
All descriptors have a length value as their first element, and a type
identification element as their second byte.
All descriptors are readable and some may be write once.
They are accessed using their type, index and selector.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix many warnings with incorrect endian assumptions
which makes the code unportable to new architectures.
The UFS specification defines the byte order as big-endian
for UPIU structure and little-endian for the host controller
transfer/task management descriptors.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Unlike 'GOOD' and 'CHECK CONDITION', other status values in
Response UPIU may or may not contain sense data. That is returning
sense data isn't obvious. So, in this case the Data Segment Length
field should be checked. If a non-zero value, it means that UPIU
has Sense Data in the Data Segment area.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Background operations in the UFS device can be disabled by
the host to reduce the response latency of transfer requests.
Add support for enabling/disabling the background operations
during runtime suspend/resume of the device.
If the device is in critical need of BKOPS it will raise an
URGENT_BKOPS exception which should be handled by the host to
make sure the device performs as expected.
During bootup, the BKOPS is enabled in the device by default.
The disable of BKOPS is supported only when the driver supports
runtime suspend/resume operations as the runtime PM framework
provides a way to determine the device idleness and hence BKOPS
can be managed effectively. During runtime resume the BKOPS is
disabled to reduce latency and during runtime suspend the BKOPS
is enabled to allow device to carry out idle time BKOPS.
In some cases where the BKOPS is disabled during runtime resume
and due to continuous data transfers the runtime suspend is not
triggered, the BKOPS is enabled when the device raises a level-2
exception (outstanding operations - performance impact).
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow UFS device to complete its initialization and accept
SCSI commands by setting fDeviceInit flag. The device may take
time for this operation and hence the host should poll until
fDeviceInit flag is toggled to zero. This step is mandated by
UFS device specification for device initialization completion.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As part of device initialization sequence, sending NOP OUT UPIU and
waiting for NOP IN UPIU response is mandatory. This confirms that the
device UFS Transport (UTP) layer is functional and the host can configure
the device with further commands. Add support for sending NOP OUT UPIU to
check the device connection path and test whether the UTP layer on the
device side is functional during initialization.
A tag is acquired from the SCSI tag map space in order to send the device
management command. When the tag is acquired by internal command the scsi
command is rejected with host busy flag in order to requeue the request.
To avoid frequent collisions between internal commands and scsi commands
the device management command tag is allocated in the opposite direction
w.r.t block layer tag allocation.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch segregates the PCI specific code in ufshcd.c to make it
ready for splitting into core ufs driver and PCI glue driver. Also
copyright header modification to remove extra warranty disclaim.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: Santosh Yaraganavi <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds support for Universal Flash Storage(UFS)
host controllers. The UFS host controller driver
includes host controller initialization method.
The Initialization process involves following steps:
- Initiate UFS Host Controller initialization process by writing
to Host controller enable register
- Configure UFS Host controller registers with host memory space
datastructure offsets.
- Unipro link startup procedure
- Check for connected device
- Configure UFS host controller to process requests
- Enable required interrupts
- Configure interrupt aggregation
[jejb: fix warnings in 32 bit compile]
Signed-off-by: Santosh Yaraganavi <santoshsy@gmail.com>
Signed-off-by: Vinayak Holikatti <vinholikatti@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@linaro.org>
Reviewed-by: Vishak G <vishak.g@samsung.com>
Reviewed-by: Girish K S <girish.shivananjappa@linaro.org>
Reviewed-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
