After a suspend-resume cycle, the resumed kernel has no idea what the
booted kernel may have done to the GuC before replacing itself with the
resumed image. In particular, it may have already loaded the GuC with
firmware, which will then cause this kernel's attempt to (re)load the
firmware to fail (GuC program memory is write-once!). The symptoms
(GuC firmware reload fails after hibernation) are further described
in the Bugzilla reference below.
So let's *always* reset the GuC just before (re)loading the firmware;
the hardware should then be in a well-known state, and we may even
avoid some of the issues arising from unpredictable timing.
Also added some more fields & values to the definition of the GUC_STATUS
register, which is the key diagnostic indicator if the GuC load fails.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Cc: Alex Dai <yu.dai@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94390
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Due to timing issues in the HW, some of the status bits required for GuC
authentication occasionally don't get set; when that happens, the GuC
cannot be initialized and we will be left with a wedged GPU. The W/A
suggested is to perform a soft reset of the GuC and attempt to reload
the F/W again for few times before giving up.
As the failure is dependent on timing, tests performed by triggering
manual full gpu reset (i915_wedged) showed that we could sometimes hit
this after several thousand iterations, but sometimes tests ran even
longer without any issues. Reset and reload mechanism proved helpful
when we indeed hit f/w load failure, so it is better to include this
to improve driver stability.
This change implements the following WAs,
WaEnableuKernelHeaderValidFix:skl,bxt
WaEnableGuCBootHashCheckNotSet:skl,bxt
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
The GuC firmware uses this for various purposes. The ADS itself is
a chunk of memory created by driver to share with GuC. Its members
are usually addresses telling where GuC to access them, including
things like scheduler policies, register list that will be saved
and restored during reset etc.
This is the first patch of a series to enable GuC ADS. For now, we
only create the ADS obj whilst keep it disabled.
v1: remove dead code checking return of kmap_atomic (Chris Wilson)
v2: use kmap instead of the atomic version of it.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450468812-4882-3-git-send-email-yu.dai@intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make I915_READ and I915_WRITE more type safe by wrapping the register
offset in a struct. This should eliminate most of the fumbles we've had
with misplaced parens.
This only takes care of normal mmio registers. We could extend the idea
to other register types and define each with its own struct. That way
you wouldn't be able to accidentally pass the wrong thing to a specific
register access function.
The gpio_reg setup is probably the ugliest thing left. But I figure I'd
just leave it for now, and wait for some divine inspiration to strike
before making it nice.
As for the generated code, it's actually a bit better sometimes. Eg.
looking at i915_irq_handler(), we can see the following change:
lea 0x70024(%rdx,%rax,1),%r9d
mov $0x1,%edx
- movslq %r9d,%r9
- mov %r9,%rsi
- mov %r9,-0x58(%rbp)
- callq *0xd8(%rbx)
+ mov %r9d,%esi
+ mov %r9d,-0x48(%rbp)
callq *0xd8(%rbx)
So previously gcc thought the register offset might be signed and
decided to sign extend it, just in case. The rest appears to be
mostly just minor shuffling of instructions.
v2: i915_mmio_reg_{offset,equal,valid}() helpers added
s/_REG/_MMIO/ in the register defines
mo more switch statements left to worry about
ring_emit stuff got sorted in a prep patch
cmd parser, lrc context and w/a batch buildup also in prep patch
vgpu stuff cleaned up and moved to a prep patch
all other unrelated changes split out
v3: Rebased due to BXT DSI/BLC, MOCS, etc.
v4: Rebased due to churn, s/i915_mmio_reg_t/i915_reg_t/
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1447853606-2751-1-git-send-email-ville.syrjala@linux.intel.com
The size / offset information of all firmware ingredients are
now caculated from header. Driver will validate the header and
rsa key size. If any component is out of boundary, driver will
reject the loading too.
v6: Clean up warnings from make docs
v5: Tidy up GuC titles in kernel/Doc
v4: Now using 'size_dw' for those defined in css_header
v3: 1) Move DOC to intel_guc_fwif.h right before css_header
definition. Add more comments.
2) Change 'size' to 'len' or 'length' to avoid confusion.
3) Add UOS_RSA_SCRATCH_MAX_COUNT according to BSpec. And
driver validate size of RSA key now.
4) Add fw component size/offset info to intel_guc_fw.
v2: Add indent into DOC to make fixed-width format rather than
change the tmpl.
v1: 1) guc_css_header is defined as __packed now
2) Add and correct GuC related topics in kernel/Doc
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bit 16 of GuC status indicates resuming from RC6. The LAPIC_DONE
status is a reliable readiness flag only when resuming from RC6.
This fix a racing issue that allocation of doorbell fails whilst
GuC init is not finished.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Alex Dai <yu.dai@intel.com>
Cc: Tom O'Rourke <Tom.O'Rourke@intel.com>
Cc: Akash Goel <akash.goel@intel.com>
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fetches the required firmware image from the filesystem,
then loads it into the GuC's memory via a dedicated DMA engine.
This patch is derived from GuC loading work originally done by
Vinit Azad and Ben Widawsky.
v2:
Various improvements per review comments by Chris Wilson
v3:
Removed 'wait' parameter to intel_guc_ucode_load() as firmware
prefetch is no longer supported in the common firmware loader,
per Daniel Vetter's request.
Firmware checker callback fn now returns errno rather than bool.
v4:
Squash uC-independent code into GuC-specifc loader [Daniel Vetter]
Don't keep the driver working (by falling back to execlist mode)
if GuC firmware loading fails [Daniel Vetter]
v5:
Clarify WOPCM-related #defines [Tom O'Rourke]
Delete obsolete code no longer required with current h/w & f/w
[Tom O'Rourke]
Move the call to intel_guc_ucode_init() later, so that it can
allocate GEM objects, and have it fetch the firmware; then
intel_guc_ucode_load() doesn't need to fetch it later.
[Daniel Vetter].
v6:
Update comment describing intel_guc_ucode_load() [Tom O'Rourke]
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_guc_fwif.h contains the subset of the GuC interface that we
will need for submission of commands through the GuC. These MUST
be kept in sync with the definitions used by the GuC firmware, and
updates to this file will (or should) be autogenerated from the
source files used to build the firmware. Editing this file is
therefore not recommended.
i915_guc_reg.h contains definitions of GuC-related hardware:
registers, bitmasks, etc. These should match the BSpec.
v2:
Files renamed & resliced per review comments by Chris Wilson
v4:
Added DON'T-EDIT-ME warning [Tom O'Rourke]
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
