These files were getting <linux/module.h> via an implicit non-obvious
path, but we want to crush those out of existence since they cost
time during compiles of processing thousands of lines of headers
for no reason. Give them the lightweight header that just contains
the EXPORT_SYMBOL infrastructure.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6:
h8300: Move gpio.h to gpio-internal.h
gpio: pl061: add DT binding support
gpio: fix build error in include/asm-generic/gpio.h
gpiolib: Ensure struct gpio is always defined
irq: Add EXPORT_SYMBOL_GPL to function of irq generic-chip
gpio-ml-ioh: Use NUMA_NO_NODE not GFP_KERNEL
gpio-pch: Use NUMA_NO_NODE not GFP_KERNEL
gpio: langwell: ensure alternate function is cleared
gpio-pch: Support interrupt function
gpio-pch: Save register value in suspend()
gpio-pch: modify gpio_nums and mask
gpio-pch: support ML7223 IOH n-Bus
gpio-pch: add spinlock in suspend/resume processing
gpio-pch: Delete invalid "restore" code in suspend()
gpio-ml-ioh: Fix suspend/resume issue
gpio-ml-ioh: Support interrupt function
gpio-ml-ioh: Delete unnecessary code
gpio/mxc: add chained_irq_enter/exit() to mx3_gpio_irq_handler()
gpio/nomadik: use genirq core to track enablement
gpio/nomadik: disable clocks when unused
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Add IRQF_RESUME_EARLY and resume such IRQs earlier
genirq: Fix fatfinered fixup really
genirq: percpu: allow interrupt type to be set at enable time
genirq: Add support for per-cpu dev_id interrupts
genirq: Add IRQCHIP_SKIP_SET_WAKE flag
Some functions of irq generic-chip is undefined, because
EXPORT_SYMBOL_GPL is not set to these.
ERROR: "irq_setup_generic_chip" [drivers/gpio/gpio-pch.ko] undefined!
ERROR: "irq_alloc_generic_chip" [drivers/gpio/gpio-pch.ko] undefined!
ERROR: "irq_setup_generic_chip" [drivers/gpio/gpio-ml-ioh.ko] undefined!
ERROR: "irq_alloc_generic_chip" [drivers/gpio/gpio-ml-ioh.ko] undefined!
This is revised that EXPORT_SYMBOL_GPL can be added and referred
to in functions.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds a mechanism to resume selected IRQs during syscore_resume
instead of dpm_resume_noirq.
Under Xen we need to resume IRQs associated with IPIs early enough
that the resched IPI is unmasked and we can therefore schedule
ourselves out of the stop_machine where the suspend/resume takes
place.
This issue was introduced by 676dc3cf5b "xen: Use IRQF_FORCE_RESUME".
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: xen-devel <xen-devel@lists.xensource.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/1318713254.11016.52.camel@dagon.hellion.org.uk
Cc: stable@kernel.org (at least to 2.6.32.y)
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
As request_percpu_irq() doesn't allow for a percpu interrupt to have
its type configured (it is generally impossible to configure it on all
CPUs at once), add a 'type' argument to enable_percpu_irq().
This allows some low-level, board specific init code to be switched to
a generic API.
[ tglx: Added WARN_ON argument ]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ARM GIC interrupt controller offers per CPU interrupts (PPIs),
which are usually used to connect local timers to each core. Each CPU
has its own private interface to the GIC, and only sees the PPIs that
are directly connect to it.
While these timers are separate devices and have a separate interrupt
line to a core, they all use the same IRQ number.
For these devices, request_irq() is not the right API as it assumes
that an IRQ number is visible by a number of CPUs (through the
affinity setting), but makes it very awkward to express that an IRQ
number can be handled by all CPUs, and yet be a different interrupt
line on each CPU, requiring a different dev_id cookie to be passed
back to the handler.
The *_percpu_irq() functions is designed to overcome these
limitations, by providing a per-cpu dev_id vector:
int request_percpu_irq(unsigned int irq, irq_handler_t handler,
const char *devname, void __percpu *percpu_dev_id);
void free_percpu_irq(unsigned int, void __percpu *);
int setup_percpu_irq(unsigned int irq, struct irqaction *new);
void remove_percpu_irq(unsigned int irq, struct irqaction *act);
void enable_percpu_irq(unsigned int irq);
void disable_percpu_irq(unsigned int irq);
The API has a number of limitations:
- no interrupt sharing
- no threading
- common handler across all the CPUs
Once the interrupt is requested using setup_percpu_irq() or
request_percpu_irq(), it must be enabled by each core that wishes its
local interrupt to be delivered.
Based on an initial patch by Thomas Gleixner.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lkml.kernel.org/r/1316793788-14500-2-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some irq chips need the irq_set_wake() functionality, but do not
require a irq_set_wake() callback. Instead of forcing an empty
callback to be implemented add a flag which notes this fact. Check for
the flag in set_irq_wake_real() and return success when set.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
If an irq_chip provides .irq_shutdown(), but neither of .irq_disable() or
.irq_mask(), free_irq() crashes when jumping to NULL.
Fix this by only trying .irq_disable() and .irq_mask() if there's no
.irq_shutdown() provided.
This revives the symmetry with irq_startup(), which tries .irq_startup(),
.irq_enable(), and irq_unmask(), and makes it consistent with the comment for
irq_chip.irq_shutdown() in <linux/irq.h>, which says:
* @irq_shutdown: shut down the interrupt (defaults to ->disable if NULL)
This is also how __free_irq() behaved before the big overhaul, cfr. e.g.
3b56f0585f ("genirq: Remove bogus conditional"),
where the core interrupt code always overrode .irq_shutdown() to
.irq_disable() if .irq_shutdown() was NULL.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Link: http://lkml.kernel.org/r/1315742394-16036-2-git-send-email-geert@linux-m68k.org
Cc: stable@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This reverts commit f3637a5f2e.
It turns out that this breaks several drivers, one example being OMAP
boards which use the on-board OMAP UARTs and the omap-serial driver that
will not boot to userspace after the commit.
Paul Walmsley reports that enabling CONFIG_DEBUG_SHIRQ reveals 'IRQ
handler type mismatch' errors:
IRQ handler type mismatch for IRQ 74
current handler: serial idle
...
and the reason is that setting IRQF_ONESHOT will now result in those
interrupt handlers having different IRQF flags, and thus being
unsharable. So the commit log in the reverted commit:
"Since it is required for those users and
there is no difference for others it makes sense to add this flag
unconditionally."
is simply not true: there may not be any difference from a "actions at
irq time", but there is a *big* difference wrt this flag testing irq
management (see __setup_irq() in kernel/irq/manage.c).
One solution may be to stop verifying IRQF_ONESHOT in __setup_irq(), but
right now the safe course of action is to revert the change. Let's
revisit this in a later merge window.
Reported-by: Paul Walmsley <paul@pwsan.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Requested-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix kernel-doc warning in irqdesc.c:
Warning(kernel/irq/irqdesc.c:353): No description found for parameter 'owner'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq: Track the owner of irq descriptor
irq: Always set IRQF_ONESHOT if no primary handler is specified
genirq: Fix wrong bit operation
Interrupt descriptors can be allocated from modules. The interrupts
are used by other modules, but we have no refcount on the module which
provides the interrupts and there is no way to establish one on the
device level as the interrupt using module is agnostic to the fact
that the interrupt is provided by a module rather than by some builtin
interrupt controller.
To prevent removal of the interrupt providing module, we can track the
owner of the interrupt descriptor, which also provides the relevant
irq chip functions in the irq descriptor.
request/setup_irq() can now acquire a refcount on the owner module to
prevent unloading. free_irq() drops the refcount.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Link: http://lkml.kernel.org/r/20110711101731.GA13804@Chamillionaire.breakpoint.cc
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If no primary handler is specified then a default one is assigned
which always returns IRQ_WAKE_THREAD. This handler requires the
IRQF_ONESHOT flag on LEVEL / EIO typed irqs because the source of
interrupt is not disabled. Since it is required for those users and
there is no difference for others it makes sense to add this flag
unconditionally.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/1310070737-18514-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
irq_domain_generate_simple() is an easy way to generate an irq translation
domain for simple irq controllers. It assumes a flat 1:1 mapping from
hardware irq number to an offset of the first linux irq number assigned
to the controller
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds irq_domain infrastructure for translating from
hardware irq numbers to linux irqs. This is particularly important
for architectures adding device tree support because the current
implementation (excluding PowerPC and SPARC) cannot handle
translation for more than a single interrupt controller. irq_domain
supports device tree translation for any number of interrupt
controllers.
This patch converts x86, Microblaze, ARM and MIPS to use irq_domain
for device tree irq translation. x86 is untested beyond compiling it,
irq_domain is enabled for MIPS and Microblaze, but the old behaviour is
preserved until the core code is modified to actually register an
irq_domain yet. On ARM it works and is required for much of the new
ARM device tree board support.
PowerPC has /not/ been converted to use this new infrastructure. It
is still missing some features before it can replace the virq
infrastructure already in powerpc (see documentation on
irq_domain_map/unmap for details). Followup patches will add the
missing pieces and migrate PowerPC to use irq_domain.
SPARC has its own method of managing interrupts from the device tree
and is unaffected by this change.
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
devres uses the pointer value as key after it's freed, which is safe but
triggers spurious use-after-free warnings on some static analysis tools.
Rearrange code to avoid such warnings.
Signed-off-by: Maxin B. John <maxin.john@gmail.com>
Reviewed-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In kernel/irq/manage.c::irq_set_irq_wake() we call
irq_get_desc_buslock() which may return NULL, but the code
dereferences the result unconditionally.
irq_set_irq_wake() has lots of callers - I checked a few and I couldn't
find anything that guarantees that they won't call it with some input that
will cause irq_get_desc_buslock() to return NULL, so I think it's a good
thing to test and -EINVAL was the most sane error code in this situation
that I could think of.
Not all callers test the return value of irq_set_irq_wake(), but those
that do take != 0 to mean error as far as I can see, so they should be
fine. I guess those that don't test actually should, but that's a
different issue.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Link: http://lkml.kernel.org/r/alpine.LNX.2.00.1106092300360.17868@swampdragon.chaosbits.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When irq_alloc_descs() is called with no base IRQ specified then it will
search for a range of IRQs starting from a specified base address. In the
case where an IRQ is specified it still does this search in order to ensure
that none of the requested range is already allocated and it still uses the
from parameter to specify the base for the search. This means that in the
case where a base is specified but from is zero (which is reasonable as
any IRQ number is in the range specified by a zero from) the function will
get confused and try to allocate the first suitably sized block of free IRQs
it finds.
Instead use a specified IRQ as the base address for the search, and insist
that any from that is specified can support that IRQ.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Link: http://lkml.kernel.org/r/1307037313-15733-1-git-send-email-broonie@opensource.wolfsonmicro.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The genirq changes are initializing descriptors for sparse IRQs quite
differently from how non-sparse (stacked?) IRQs are initialized, with
the effect that on my platform all IRQs are default-disabled on sparse
IRQs and default-enabled if non-sparse IRQs are used, crashing some
GPIO driver.
Fix this by refactoring the non-sparse IRQs to use the same descriptor
init function as the sparse IRQs.
Signed-off: Linus Walleij <linus.walleij@linaro.org>
Link: http://lkml.kernel.org/r/1306858479-16622-1-git-send-email-linus.walleij@stericsson.com
Cc: stable@kernel.org # 2.6.39
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The detection of spurios interrupts is currently limited to first level
handler. In force-threaded mode we never notice if the threaded irq does
not feel responsible.
This patch catches the return value of the threaded handler and forwards
it to the spurious detector. If the primary handler returns only
IRQ_WAKE_THREAD then the spourious detector ignores it because it gets
called again from the threaded handler.
[ tglx: Report the erroneous return value early and bail out ]
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Link: http://lkml.kernel.org/r/1306824972-27067-2-git-send-email-sebastian@breakpoint.cc
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In forced threaded mode (or with an explicit threaded handler) we only
see the primary handler, but not the threaded handler.
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Link: http://lkml.kernel.org/r/1306824972-27067-1-git-send-email-sebastian@breakpoint.cc
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit 4b06042(bitmap, irq: add smp_affinity_list interface to
/proc/irq) causes the following warning:
[ 274.239500] WARNING: at fs/proc/generic.c:850 remove_proc_entry+0x24c/0x27a()
[ 274.251761] remove_proc_entry: removing non-empty directory 'irq/184',
leaking at least 'smp_affinity_list'
Remove the new file in the exit path.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Mike Travis <travis@sgi.com>
Link: http://lkml.kernel.org/r/4DDDE094.6050505@kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Manually adjusting the smp_affinity for IRQ's becomes unwieldy when the
cpu count is large.
Setting smp affinity to cpus 256 to 263 would be:
echo 000000ff,00000000,00000000,00000000,00000000,00000000,00000000,00000000 > smp_affinity
instead of:
echo 256-263 > smp_affinity_list
Think about what it looks like for cpus around say, 4088 to 4095.
We already have many alternate "list" interfaces:
/sys/devices/system/cpu/cpuX/indexY/shared_cpu_list
/sys/devices/system/cpu/cpuX/topology/thread_siblings_list
/sys/devices/system/cpu/cpuX/topology/core_siblings_list
/sys/devices/system/node/nodeX/cpulist
/sys/devices/pci***/***/local_cpulist
Add a companion interface, smp_affinity_list to use cpu lists instead of
cpu maps. This conforms to other companion interfaces where both a map
and a list interface exists.
This required adding a bitmap_parselist_user() function in a manner
similar to the bitmap_parse_user() function.
[akpm@linux-foundation.org: make __bitmap_parselist() static]
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export handle_simple_irq, irq_modify_status, irq_alloc_descs,
irq_free_descs and generic_handle_irq to allow their usage in
modules. First user is IIO, which wants to be built modular, but needs
to be able to create irq chips, allocate and configure interrupt
descriptors and handle demultiplexing interrupts.
[ tglx: Moved the uninlinig of generic_handle_irq to a separate patch ]
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Link: http://lkml.kernel.org/r/%3C1305711544-505-1-git-send-email-jic23%40cam.ac.uk%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
generic_handle_irq() is missing a NULL pointer check for the result of
irq_to_desc. This was a not a big problem, but we want to expose it to
drivers, so we better have sanity checks in place. Add a return value
as well, which indicates that the irq number was valid and the handler
was invoked.
Based on the pure code move from Jonathan Cameron.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
kernel/irq/ is only built when CONFIG_GENERIC_HARDIRQS=y. So making
code inside of kernel/irq/ conditional on CONFIG_GENERIC_HARDIRQS is
pointless.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit ab7798ffcf ("genirq: Expand generic
show_interrupts()") added the Kconfig option GENERIC_IRQ_SHOW_LEVEL to
accomodate PowerPC, but this doesn't actually enable the functionality due
to a typo in the #ifdef check.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Linux/PPC Development <linuxppc-dev@lists.ozlabs.org>
Link: http://lkml.kernel.org/r/%3Calpine.DEB.2.00.1104302251370.19068%40ayla.of.borg%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
These callbacks are only called in the syscore suspend/resume code on
interrupt chips which have been registered via the generic irq chip
mechanism. Calling those callbacks per irq would be rather icky, but
with the generic irq chip mechanism we can call this per registered
chip.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Implement a generic interrupt chip, which is configurable and is able
to handle the most common irq chip implementations.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Tested-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by; Kevin Hilman <khilman@ti.com>
This adds support for disabling threading on a per-IRQ basis via the IRQ
status instead of the IRQ flow, which is necessary for interrupts that
don't follow the natural IRQ flow channels, such as those that are
virtually created.
The new APIs added are simply:
irq_set_thread()
irq_set_nothread()
which follow the rest of the IRQ status routines.
Chained handlers also have IRQ_NOTHREAD set on them automatically, making
the lack of threading explicit rather than implicit. Subsequently, the
nothread flag can be viewed through the standard genirq debugging
facilities.
[ tglx: Fixed cleanup fallout ]
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Link: http://lkml.kernel.org/r/%3C20110406210135.GF18426%40linux-sh.org%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, fpu: Fix FPU exception handling on non-SSE systems
x86, hibernate: Initialize mmu_cr4_features during boot
x86-32, NUMA: Fix ACPI NUMA init broken by recent x86-64 change
x86: visws: Fixup irq overhaul fallout
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Clean up rebalance_domains() load-balance interval calculation
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/mrst/vrtc: Fix boot crash in mrst_rtc_init()
rtc, x86/mrst/vrtc: Fix boot crash in rtc_read_alarm()
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
genirq: Fix cpumask leak in __setup_irq()
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf probe: Fix listing incorrect line number with inline function
perf probe: Fix to find recursively inlined function
perf probe: Fix multiple --vars options behavior
perf probe: Fix to remove redundant close
perf probe: Fix to ensure function declared file
The allocated cpumask should be freed in __setup_irq().
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
LKML-Reference: <1301744375-6812-1-git-send-email-dfeng@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The only subtle difference is that alpha uses ACTUAL_NR_IRQS and
prints the IRQF_DISABLED flag.
Change the generic implementation to deal with ACTUAL_NR_IRQS if
defined.
The IRQF_DISABLED printing is pointless, as we nowadays run all
interrupts with irqs disabled.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The late night fixup missed to convert the data type from irq_desc to
irq_data, which results in a harmless but annoying warning.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
I missed the CONFIG_GENERIC_PENDING_IRQ dependency in the affinity
related functions and the IRQ_LEVEL propagation into irq_data
state. Did not pop up on my main test platforms. :(
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: David Daney <ddaney@caviumnetworks.com>
Fix new irq-related kernel-doc warnings in 2.6.38:
Warning(kernel/irq/manage.c:149): No description found for parameter 'mask'
Warning(kernel/irq/manage.c:149): Excess function parameter 'cpumask' description in 'irq_set_affinity'
Warning(include/linux/irq.h:161): No description found for parameter 'state_use_accessors'
Warning(include/linux/irq.h:161): Excess struct/union/enum/typedef member 'state_use_accessor' description in 'irq_data'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
LKML-Reference: <20110318093356.b939558d.randy.dunlap@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Paul Gortmaker