8000 series adapters support filtering VXLAN, NVGRE and GENEVE traffic
based on inner fields, and when the NIC recognises such traffic, it
does not match unencapsulated traffic filters any more. So add catch-
all filters for encapsulated traffic on supporting platforms.
Although recognition of VXLAN and GENEVE is based on UDP ports, and thus
will not occur until the driver (on the primary PF) notifies the
firmware of UDP ports to use, NVGRE will always be recognised, hence
without this patch 8000 series adapters will drop all NVGRE traffic.
Partly based on patches by Jon Cooper <jcooper@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationalise several debug-or-warnings printks using netif_cond_dbg
to make output more consistent.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NIC is switched from full-featured to low-latency, encapsulated
filters are no longer available, and this causes errors. This patch
removes those filters from the filter table on restore.
Also, if filters which are removed by the above, or which we fail to
insert when restoring filters, were UC, MC or broadcast default
filters, invalidate the corresponding vlan->default_filters entry.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PIO buffer allocation can fail for two valid reasons:
- we've run out of them (results in -ENOSPC)
- the NIC configuration doesn't support them (results in -EPERM)
Since both these failures are expected netif_err is excessive.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensures that we report the key and indirection table the NIC is using,
rather than (if setting them failed earlier) what we wanted it to use.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8000 series SFC NICs have 4K PIO buffers, rather than the 2K of
the 7000 series. Rather than having a hard-coded PIO buffer size
(ER_DZ_TX_PIOBUF_SIZE), read it from the GET_CAPABILITIES_V2 MCDI
response.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an option descriptor has been sent on a queue but not followed by a
packet, there will have been no completion event, so the read and write
counts won't match and we'll think we can't do PIO. This combines with
the fact that we have two TX queues (for en/disable checksum offload),
and that both must be empty for PIO to happen.
This patch adds a separate "packet_write_count" that tracks the most
recent write_count we expect to see a completion event for; this excludes
option descriptors but _includes_ PIO descriptors (even though they look
like option descriptors). This is then used, rather than write_count,
in efx_nic_tx_is_empty().
We only bother to maintain packet_write_count on EF10, since on Siena
(a) there are no option descriptors and it always equals write_count, and
(b) there's no PIO, so we don't need it anyway.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_zero_addr to assign zero address to the given address array
instead of memset when the second argument in memset is address
of zero which makes the code clearer and also add header
file linux/etherdevice.h
Signed-off-by: Shyam Saini <mayhs11saini@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/sfc/efx.c:2337:5: warning:
symbol 'efx_get_phys_port_id' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting dev_port changes the device names allocated by systemd. Any devices
with a dev_port >0 will (in default distro configurations) have a suffix of
"d<port-number>" appended.
This is not something done by other drivers, and causes confusion for users.
Fixes: 8be41320f3 ("sfc: Add code to export port_num in netdev->dev_port")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output is of the form p<port-number>.
Note that the port numbers don't necessarily map one-to-one to physical
cages, partly because of 4x10G port modes on QSFP+ and partly because
of hw/fw implementation details.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no good reason why this should be an SRIOV-only thing.
Thus, also move it out of SRIOV-specific files.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we failed to set up RSS on EF10 (e.g. because firmware declared
RX_RSS_LIMITED), ethtool --show-nfc $dev rx-flow-hash ... should report
no fields, rather than confusingly reporting what fields we _would_ be
hashing on if RSS was working.
Fixes: dcb4123cbe ("sfc: disable RSS when unsupported")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
5a6681e22c ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
there are two drivers for Solarflare devices, but both still show up
directly beneath "Ethernet driver support" in the Kconfig. Follow the
pattern of other vendors and group them beneath an own vendor Kconfig
entry for Solarflare.
Cc: Edward Cree <ecree@solarflare.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes and cleanups from David Miller:
1) Revert bogus nla_ok() change, from Alexey Dobriyan.
2) Various bpf validator fixes from Daniel Borkmann.
3) Add some necessary SET_NETDEV_DEV() calls to hsis_femac and hip04
drivers, from Dongpo Li.
4) Several ethtool ksettings conversions from Philippe Reynes.
5) Fix bugs in inet port management wrt. soreuseport, from Tom Herbert.
6) XDP support for virtio_net, from John Fastabend.
7) Fix NAT handling within a vrf, from David Ahern.
8) Endianness fixes in dpaa_eth driver, from Claudiu Manoil
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (63 commits)
net: mv643xx_eth: fix build failure
isdn: Constify some function parameters
mlxsw: spectrum: Mark split ports as such
cgroup: Fix CGROUP_BPF config
qed: fix old-style function definition
net: ipv6: check route protocol when deleting routes
r6040: move spinlock in r6040_close as SOFTIRQ-unsafe lock order detected
irda: w83977af_ir: cleanup an indent issue
net: sfc: use new api ethtool_{get|set}_link_ksettings
net: davicom: dm9000: use new api ethtool_{get|set}_link_ksettings
net: cirrus: ep93xx: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb3: use new api ethtool_{get|set}_link_ksettings
net: chelsio: cxgb2: use new api ethtool_{get|set}_link_ksettings
bpf: fix mark_reg_unknown_value for spilled regs on map value marking
bpf: fix overflow in prog accounting
bpf: dynamically allocate digest scratch buffer
gtp: Fix initialization of Flags octet in GTPv1 header
gtp: gtp_check_src_ms_ipv4() always return success
net/x25: use designated initializers
isdn: use designated initializers
...
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
Logically, EFX_BUG_ON_PARANOID can never be correct. For, BUG_ON should
only be used if it is not possible to continue without potential harm;
and since the non-DEBUG driver will continue regardless (as the BUG_ON is
compiled out), clearly the BUG_ON cannot be needed in the DEBUG driver.
So, replace every EFX_BUG_ON_PARANOID with either an EFX_WARN_ON_PARANOID
or the newly defined EFX_WARN_ON_ONCE_PARANOID.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's no longer used now that Falcon is gone.
Also remove a reference in a comment to an ioctl that doesn't exist.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Easy enough for Falcon users to enable it when making oldconfig.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defalconisation removed one of the string arguments, but missed the
corresponding %s.
Fixes: 5a6681e22c ("sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driver")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationale: The differences between Falcon and Siena are in many ways larger
than those between Siena and EF10 (despite Siena being nominally "Falcon-
architecture"); for instance, Falcon has no MCPU, so there is no MCDI.
Removing Falcon support from the sfc driver should simplify the latter,
and avoid the possibility of Falcon support being broken by changes to sfc
(which are rarely if ever tested on Falcon, it being end-of-lifed hardware).
The sfc-falcon driver created in this changeset is essentially a copy of the
sfc driver, but with Siena- and EF10-specific code, including MCDI, removed
and with the "efx_" identifier prefix changed to "ef4_" (for "EFX 4000-
series") to avoid collisions when both drivers are built-in.
This changeset removes Falcon from the sfc driver's PCI ID table; then in
sfc I've removed obvious Falcon-related code: I removed the Falcon NIC
functions, Falcon PHY code, and EFX_REV_FALCON_*, then fixed up everything
that referenced them.
Also, increment minor version of both drivers (to 4.1).
For now, CONFIG_SFC selects CONFIG_SFC_FALCON, so that updating old configs
doesn't cause Falcon support to disappear; but that should be undone at
some point in the future.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't use ->heap_buf after commit 46d1efd852 ("sfc: remove Software
TSO") so let's remove the last traces.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It gives no advantage over GSO now that xmit_more exists. If we find
ourselves unable to handle a TSO skb (because our TXQ doesn't have a
TSOv2 context and the NIC doesn't support TSOv1), hand it back to GSO.
Also do that if the TSO handler fails with EINVAL for any other reason.
As Falcon-architecture NICs don't support any firmware-assisted TSO,
they no longer advertise TSO feature flags at all.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we fail to init the TXQ because of insufficient TSOv2 contexts,
try again with TSOv2 disabled.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for FATSOv2 to the driver. FATSOv2 offloads far more of the task
of TCP segmentation to the firmware, such that we now just pass a single
super-packet to the NIC. This means TSO has a great deal in common with a
normal DMA transmit, apart from adding a couple of option descriptors.
NIC-specific checks have been moved off the fast path and in to
initialisation where possible.
This also moves FATSOv1/SWTSO to a new file (tx_tso.c). The end of transmit
and some error handling is now outside TSO, since it is common with other
code.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling napi_hash_del() after netif_napi_del() is pointless.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Edward Cree <ecree@solarflare.com>
Cc: Bert Kenward <bkenward@solarflare.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to break the hard dependency between the PTP clock subsystem and
ethernet drivers capable of being clock providers, this patch provides
simple PTP stub functions to allow linkage of those drivers into the
kernel even when the PTP subsystem is configured out. Drivers must be
ready to accept NULL from ptp_clock_register() in that case.
And to make it possible for PTP to be configured out, the select statement
in those driver's Kconfig menu entries is converted to the new "imply"
statement. This way the PTP subsystem may have Kconfig dependencies of
its own, such as POSIX_TIMERS, without having to make those ethernet
drivers unavailable if POSIX timers are cconfigured out. And when support
for POSIX timers is selected again then the default config option for PTP
clock support will automatically be adjusted accordingly.
The pch_gbe driver is a bit special as it relies on extra code in
drivers/ptp/ptp_pch.c. Therefore we let the make process descend into
drivers/ptp/ even if PTP_1588_CLOCK is unselected.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-kbuild@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Michal Marek <mmarek@suse.com>
Link: http://lkml.kernel.org/r/1478841010-28605-4-git-send-email-nicolas.pitre@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
efx_copy_channel() doesn't correctly clear the napi_hash related state.
This means that when napi_hash_add is called for that channel nothing is
done, and we are left with a copy of the napi_hash_node from the old
channel. When we later call napi_hash_del() on this channel we have a
stale napi_hash_node.
Corruption is only seen when there are multiple entries in one of the
napi_hash lists. This is made more likely by having a very large number
of channels. Testing was carried out with 512 channels - 32 channels on
each of 16 ports.
This failure typically appears as protection faults within napi_by_id()
or napi_hash_add(). efx_copy_channel() is only used when tx or rx ring
sizes are changed (ethtool -G).
Fixes: 36763266bb ("sfc: Add support for busy polling")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves UDP spreading, and also slightly improves GRO performance
of encapsulated TCP on 7000 series NICs.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 61e84623ac ("net: centralize net_device min/max MTU checking")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a NULL check before calling asynchronous MCDI completion functions
during device removal.
Fixes: 7014d7f6 ("sfc: allow asynchronous MCDI without completion function")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers must be ready to accept NULL from ptp_clock_register() if the
PTP clock subsystem is configured out.
This patch documents that and ensures that all drivers cope well
with a NULL return.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Reviewed-by: Eugenia Emantayev <eugenia@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Ma Yuying <yuma@redhat.com>
Suggested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC_CMD_TRIGGER_INTERRUPT does not work on the SFC9140, as used in the
sfn7x42q and sfn7x24f.
Check for this using the MCDI workaround mechanism.
The command is only used during self test. If it's not supported, skip
the interrupt test.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nic_data was already initialised to the right thing, no need to assign
it again.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX size bins were not supported on the 7000's 40G MAC, but the 8000 series
does support them and the MCPU advertises that via a new capability bit.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit systems, mask is only an array of 3 longs, not 4, so don't try
to write to mask[3].
Also include build-time checks in case the size of the bitmask changes.
Fixes: 3c36a2aded ("sfc: display vadaptor statistics for all interfaces")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The division is already being done properly in efx_ef10_get_timer_config
which returns zero-on-success, unlike the old efx_ef10_get_sysclk_freq.
Fixes: d95e329a55 ("sfc: get timer configuration from adapter")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SFN8000 series adapters the MC provides a method to get the timer
quantum and the maximum timer setting. We revert to the old values if the
new call is unavailable.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFN8000-series NICs require a new method of setting interrupt moderation,
via MCDI. This is indicated by a workaround flag. This new MCDI command
takes an explicit time value rather than a number of ticks. It therefore
makes sense to also store the moderation values in terms of time, since
that is what the ethtool interface is interested in.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than explicitly specifying flags we can now specify a desired
performance target to the firmware, ie higher throughput or lower latency.
For now we use the default "auto" configuration.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with -Wextra, we get a harmless warning from the
EFX_EXTRACT_OWORD32 macro:
ethernet/sfc/farch.c: In function 'efx_farch_test_registers':
ethernet/sfc/farch.c:119:30: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:144: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:392: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
ethernet/sfc/farch.c:124:731: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
The macro and the caller are both correct, but we can avoid the
warning by changing the index variable to a signed type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If vPort has VLAN_RESTRICT flag, VLAN tagged traffic will not be
delivered without corresponding Rx filters which may be proxied to and
moderated by hypervisor.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If should be done after net_dev->hw_features initialization, to keep the
feature there to be able to enable it later using ethtool.
VLAN filtering is enforced and fixed if vPort requires usage of VLAN
filters to receive tagged traffic.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If it is not supported we simply disable the feature.
For the feature to work we need firmware filter support for
OUTER_VID + LOC_MAC and for OUTER_VID + LOC_MAC_IG.
The low-latency firmware can match on OUTER_VID + LOC_MAC but not on
OUTER_VID + LOC_MAC_IG.
For the capture packet firmware it is the other way around.
Only the full-feature variant can match on both combinations.
Incorporates a fix by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
in the net_dev->[hw_]features handling.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filter match flags are not unique criteria to be mapped to priority
because of both unknown unicast and unknown multicast are mapped to
LOC_MAC_IG. So, local MAC is required to map filter to priority.
MCDI filter flags is unique criteria to find filter priority.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nearly every time we call efx_ef10_filter_remove_unsafe, we first check
for EFX_EF10_FILTER_ID_INVALID, in which case we do nothing. So move
that check into the function, simplifying all the call sites.
Also, change the return type to void, since none of the callers check it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to enslave an SFC interface to a bond the following BUG_ON was
hit:
kernel BUG [in ef10.c]!
CPU: 0 PID: 4383 Comm: ifenslave Tainted: G
...
Call Trace:
efx_ef10_filter_add_vlan+0x121/0x180 [sfc]
efx_ef10_filter_table_probe+0x2a2/0x4f0 [sfc]
efx_ef10_set_mac_address+0x370/0x6d0 [sfc]
efx_set_mac_address+0x7d/0x120 [sfc]
dev_set_mac_address+0x43/0xa0
bond_enslave+0x337/0xea0 [bonding]
This comes from function efx_ef10_filter_vlan_sync_rx_mode.
To solve the bug we ensure the mac_lock is taken before calling
efx_ef10_filter_add_vlan. But to avoid a priority inversion mac_lock must
be taken before filter_sem.
To satisfy these requirements we end up taking mac_lock in
efx_ef10_vport_set_mac_address, efx_ef10_set_mac_address,
efx_ef10_sriov_set_vf_vlan and efx_probe_filters.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supports HW VLAN filtering, en/disabled using ethtool.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now it contains dummy VLAN entry with unspecified VID only.
The entry is used for the case when HW VLAN filtering is not used.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These flags are built when address cache is updated.
The information will be required when VLAN filtering is added and address
cache is used without re-sync.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a step to support VLAN filtering in HW.
Until then, there is only one struct efx_ef10_filter_vlan per struct
efx_ef10_filter_table, with no VLAN information yet.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is required to remove setting of filter IDs to invalid from multicast
and unicast addresses caching functions.
Add initialization to invalid when filter table is created.
Add paranoid checks to track consistency.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on a patch by Andrew Rybchenko <Andrew.Rybchenko@oktetlabs.ru>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It allows to change set of fixed features on datapath reset.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is used for EF10 only and logically belongs to EF10 filter table state.
It is OK that it is reset to false on filter table recreation since all
filters are removed on destruction.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
7000-series SFC NICs connected with an SFP+ module currently fail to
report any supported link speeds.
Reported-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Reviewed-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we get confused when two flows on different channels get the
same flow ID.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise, if we fail to allocate new PIO buffers, our TXQs will try to
use the old ones, which aren't there any more.
Fixes: 183233bec8 "sfc: Allocate and link PIO buffers; map them with write-combining"
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When certain firmware variants are selected (via the sfboot utility) the
SFC7000 and SFC8000 series NICs don't support RSS. The driver still
tries (and fails) to insert filters with the RSS flag, and the NIC fails
to pass traffic.
When the firmware reports RSS_LIMITED suppress allocating a default RSS
context. The absence of an RSS context is picked up in filter insertion
and RSS flags are discarded.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaa ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.
This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on configuration the NIC may return errors for unprivileged
functions and/or VFs. Where these are expected and handled, reduce the
level of any output.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in an unprivileged function we expect some MC commands
to fail with permission errors. To avoid log spew downgrade these to
debug only.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are situations - mostly reset related - where our view of the
filter table differs from the hardware. In this case we may try and
remove filters that aren't actually installed. This isn't that
interesting in most situations, so downgrade the logging.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For unprivileged functions operations can be authorised by an admin
function. Extra steps are introduced to the MCDI protocol in this
situation - the initial response from the MCDI tells us that the
operation has been deferred, and we must retry when told. We then
receive an event telling us to retry.
Note that this provides only the functionality for the unprivileged
functions, not the handling of the administrative side.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After reboot the vswitch configuration from the PF may not be
complete before the VF attempts to restore filters. In that
case we see NO_EVB_PORT errors from the MC. Retry up to a time
limit or until a different result is seen.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
These netif flags are unnecessary convolutions. It is more
straightforward to just use NETIF_F_HW_CSUM, NETIF_F_IP_CSUM,
and NETIF_F_IPV6_CSUM directly.
This patch also:
- Cleans up can_checksum_protocol
- Simplifies netdev_intersect_features
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We test for if "tries" is zero at the end but "tries--" is a post-op so
it will end with "tries" set to -1. I have changed it to a pre-op
instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, filter insertion on a VF would fail if only one channel
was in use. This would include the unicast station filter and therefore
no traffic would be received.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A change in MCFW behaviour means that the net driver must update its record
of the warm_boot_count by reading it from the ER_DZ_BIU_MC_SFT_STATUS
register.
On v4.6.x MCFW the global boot count was incremented when some functions
needed to be reset to enable multicast chaining, so all functions saw the
same value. In that case, the driver needed to increment its
warm_boot_count when other functions were reset, to avoid noticing it later
and then trying to reset itself to recover unnecessarily.
With v4.7+ MCFW, the boot count in firmware doesn't change as that is
unnecessary since the PFs that have been reset will each receive an MC
reboot notification. In that case, the driver re-reads the unchanged
value.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't open-code it.
CC: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also add support for 7000 series 40G NIC VF.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Solarflare 8000 series NIC will use a new TSO scheme. The current
driver refuses to load if the current TSO scheme is not found. Remove
that check and instead make the TSO version a per-queue parameter.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
