Enable the PCIE EP RC for iMX
- hw setup:
* two imx boards, one is used as pcie rc, the other is used
as pcie ep.
RC TX N/P <--> EP RX N/P
RX N/P <--> EP TX N/P
- sw setup:
* when build rc image, make sure that
CONFIG_PCI_IMX6=y
CONFIG_RC_MODE_IN_EP_RC_SYS=y
* when build ep image
CONFIG_PCI_IMX6=y
CONFIG_EP_MODE_IN_EP_RC_SYS=y
- features:
* set-up link between rc and ep by their stand-alone
ref clk running internally.
* in ep's system, ep can access the reserved ddr memory
(default address:0x4000_0000 on imx6q sd board, and
0xb000_0000 on imx6sx sdb and imx7d arm2 boards) of
pcie rc's system, by the interconnection between pcie
ep and pcie rc.
* provide one example, howto configure the bar# of ep and so on,
when pcie ep emaluates one memory ram ep device
* setup one new outbound memory region at rc side, let imx pcie rc
can access the memory of imx pcie ep in imx pcie rc ep validation
system.
- NOTE:
* boot up ep platform firstly, then boot up rc platform.
* For imx6q/6dl/6sx/7d sabresd boards, make sure that mem=768M is
contained in the kernel command line,
since the start address of the upper 256mb of the 1g ddr mem is
reserved to do the pcie ep rc access operations in default.
- RC access memory of EP:
- EP:
write the <ddr_region_address> to the bar0 of ep.
echo <ddr_region_address> > /sys/devices/.../pcie/ep_bar0_addr
- RC:
access the <pcie_mem_base_addr>, and this address
would be mapped to the <ddr_region_address> of ep.
- Note:
ddr_region_address pcie_mem_base_addr bar0_addr
imx6qdl 0x4000_0000 0x0100_0000 0x01ff_c010
imx6sx 0xb000_0000 0x0800_0000 0x08ff_c010
imx7d 0xb000_0000 0x4000_0000 0x3380_0010
imx8mq 0xb820_0000 0x2000_0000 0x33c0_0010
imx8mm 0xb820_0000 0x1800_0000 0x3380_0010
imx8qm 0x9020_0000 0x6000_0000 0x5f00_0010
imx8qxp 0x9020_0000 0x7000_0000 0x5f01_0010
- The example of the RC access memory of EP
step1:
EP side:
echo 0x90200000 > /sys/devices/platform/bus@5f000000/5f000000.pcie
/ep_bar0_addr
root@imx8_all:~# ./memtool 90200000 4
Reading 0x4 count starting at address 0x90200000
0x90200000: 00000000 00000000 00000000 00000000
RC side:
./memtool 60000000=55aa55aa
Writing 32-bit value 0x55AA55AA to address 0x60000000
EP side:
root@imx8_all:~# ./memtool 90200000 4
Reading 0x4 count starting at address 0x90200000
0x90200000: 55AA55AA 00000000 00000000 00000000
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
- Fix Tegra OF node reference leak (Nishka Dasgupta)
- Add #defines for PCIe Data Link Feature and Physical Layer 16.0 GT/s
features (Vidya Sagar)
- Disable MSI for Tegra Root Ports since they don't support using MSI for
all Root Port events (Vidya Sagar)
- Group DesignWare write-protected register writes together (Vidya Sagar)
- Move DesignWare capability search interfaces so they can be used by
both host and endpoint drivers (Vidya Sagar)
- Add DesignWare extended capability search interfaces (Vidya Sagar)
- Export dw_pcie_wait_for_link() so drivers can be modules (Vidya Sagar)
- Add "snps,enable-cdm-check" DT binding for Configuration Dependent
Module (CDM) register checking (Vidya Sagar)
- Add DesignWare support for "snps,enable-cdm-check" CDM checking (Vidya
Sagar)
- Add "supports-clkreq" DT binding for host drivers to decide whether to
advertise low power features (Vidya Sagar)
- Add DT binding for Tegra194 (Vidya Sagar)
- Add DT binding for Tegra194 P2U (PIPE to UPHY) block (Vidya Sagar)
- Add support for Tegra194 P2U (PIPE to UPHY) (Vidya Sagar)
- Add support for Tegra194 host controller (Vidya Sagar)
- Add Tegra support for sideband PERST# and CLKREQ# for C5 (Vidya Sagar)
- Add Tegra support for slot regulators for p2972-0000 platform (Vidya
Sagar)
* lorenzo/pci/tegra:
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
phy: tegra: Add PCIe PIPE2UPHY support
dt-bindings: PHY: P2U: Add Tegra194 P2U block
dt-bindings: PCI: tegra: Add device tree support for Tegra194
dt-bindings: Add PCIe supports-clkreq property
PCI: dwc: Add support to enable CDM register check
dt-bindings: PCI: designware: Add binding for CDM register check
PCI: dwc: Export dw_pcie_wait_for_link() API
PCI: dwc: Add extended configuration space capability search API
PCI: dwc: Move config space capability search API
PCI: dwc: Group DBI registers writes requiring unlocking
PCI: Disable MSI for Tegra root ports
PCI: Add #defines for some of PCIe spec r4.0 features
PCI: tegra: Fix OF node reference leak
- Mark Layerscape endpoint BARs 2 and 4 as 64-bit (Xiaowei Bao)
- Add CONFIG_PCI_LAYERSCAPE_EP so EP/RC can be built separately (Xiaowei
Bao)
* remotes/lorenzo/pci/layerscape:
PCI: layerscape: Add CONFIG_PCI_LAYERSCAPE_EP to build EP/RC separately
PCI: layerscape: Add the bar_fixed_64bit property to the endpoint driver
This driver is DT based and utilizes the DesignWare APIs.
It allows using a smaller ECAM range for a larger bus range -
usually an entire bus uses 1MB of address space, but the driver
can use it for a larger number of buses. This is achieved by using a HW
mechanism which allows changing the BUS part of the "final" outgoing
config transaction. There are 2 HW regs, one which is basically a
bitmask determining which bits to take from the AXI transaction itself
and another which holds the complementary part programmed by the
driver.
All link initializations are handled by the boot FW.
Signed-off-by: Jonathan Chocron <jonnyc@amazon.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add support for Synopsys DesignWare core IP based PCIe host controller
present in the Tegra194 SoC.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Add CONFIG_PCI_LAYERSCAPE_EP so that endpoint and host controller
drivers can be built separately.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The imx6 driver can be used on imx6sx without enabling support for
imx6q or imx7d but the "depends on" condition doesn't allow that.
Instead of making the condition even longer just make it depend on
"ARCH_MXC || COMPILE_TEST" instead.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Add PCIe EP support for AM654x Platforms in pci-keystone.c
Link: https://lore.kernel.org/linux-pci/20190325093947.32633-15-kishon@ti.com/
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
[lorenzo.pieralisi@arm.com: made dev_vdbg() call a comment]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add PCIe RC support for AM654x Platforms in pci-keystone.c
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This introduces specific glue layer for UniPhier platform to support
PCIe host controller that is based on the DesignWare PCIe core, and
this driver supports Root Complex (host) mode.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The Amlogic Meson PCIe host controller is based on the Synopsys DesignWare
PCI core. This patch adds the driver support for Meson PCIe controller.
Link: https://lore.kernel.org/linux-pci/20181218224708.GB22610@google.com/
Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
[lorenzo.pieralisi@arm.com: updated coding/comment style]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The IMX6 PCI-e host driver also supports the IMX7d. However, the
Kconfig dependencies of the driver prevented it from being enabled
unless the kernel was built with both IMX6 and IMX7 support.
It works fine to build with only IMX7 support enabled therefore
adjust the Kconfig entry to allow this configuration.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
PCIE_DW_PLAT_HOST does not have any platform dependency, so it should
not default to yes.
Fixes: 1d906b2207 ("PCI: dwc: Add support for EP mode")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Native PCI drivers for root complex devices were originally all in
drivers/pci/host/. Some of these devices can also be operated in endpoint
mode. Drivers for endpoint mode didn't seem to fit in the "host"
directory, so we put both the root complex and endpoint drivers in
per-device directories, e.g., drivers/pci/dwc/, drivers/pci/cadence/, etc.
These per-device directories contain trivial Kconfig and Makefiles and
clutter drivers/pci/. Make a new drivers/pci/controllers/ directory and
collect all the device-specific drivers there.
No functional change intended.
Link: https://lkml.kernel.org/r/1520304202-232891-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Richard Zhu