The function do_suspend_lowlevel() is specific to x86 and defined in
assembly code, so it should be called from the x86 low-level suspend
code rather than from acpi_suspend_enter().
Merge do_suspend_lowlevel() into the x86's acpi_save_state_mem() and
change the name of the latter to acpi_suspend_lowlevel(), so that the
function's purpose is better reflected by its name.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Use the unified trampoline allocation setup to allocate and install
the ACPI wakeup code in low memory.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <4D5DFBE4.7090104@intel.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Matthieu Castet <castet.matthieu@free.fr>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
We reserve lowmem for the things that need it, like the ACPI
wakeup code, way early to guarantee availability. This happens
before we set up the proper pagetables, so set_memory_x() has no
effect.
Until we have a better solution, use an initcall to mark the
wakeup code executable.
Originally-by: Matthieu Castet <castet.matthieu@free.fr>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Matthias Hopf <mhopf@suse.de>
Cc: rjw@sisk.pl
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <4D4F8019.2090104@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since checkin ebba638ae7 we call
verify_cpu even in 32-bit mode. Unfortunately, calling a function
means using the stack, and the stack pointer was not initialized in
the 32-bit setup code! This code initializes the stack pointer, and
simplifies the interface slightly since it is easier to rely on just a
pointer value rather than a descriptor; we need to have different
values for the segment register anyway.
This retains start_stack as a virtual address, even though a physical
address would be more convenient for 32 bits; the 64-bit code wants
the other way around...
Reported-by: Matthieu Castet <castet.matthieu@free.fr>
LKML-Reference: <4D41E86D.8060205@free.fr>
Tested-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Commit b40827fa72 ("x86-32, mm: Add an initial page table for core
bootstrapping") added an include directive which is needless and is
taken care of by a previous one. Remove it.
Caught-by: Jaswinder Singh Rajput <jaswinderlinux@gmail.com>
Signed-off-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-trampoline-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, mm: Add an initial page table for core bootstrapping
This patch adds an initial page table with low mappings used exclusively
for booting APs/resuming after ACPI suspend/machine restart. After this,
there's no need to add low mappings to swapper_pg_dir and zap them later
or create own swsusp PGD page solely for ACPI sleep needs - we have
initial_page_table for that.
Signed-off-by: Borislav Petkov <bp@alien8.de>
LKML-Reference: <20101020070526.GA9588@liondog.tnic>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
1.include linux/memblock.h directly. so later could reduce e820.h reference.
2 this patch is done by sed scripts mainly
-v2: use MEMBLOCK_ERROR instead of -1ULL or -1UL
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Commit 2a6b69765a
(ACPI: Store NVS state even when entering suspend to RAM) caused the
ACPI suspend code save the NVS area during suspend and restore it
during resume unconditionally, although it is known that some systems
need to use acpi_sleep=s4_nonvs for hibernation to work. To allow
the affected systems to avoid saving and restoring the NVS area
during suspend to RAM and resume, introduce kernel command line
option acpi_sleep=nonvs and make acpi_sleep=s4_nonvs work as its
alias temporarily (add acpi_sleep=s4_nonvs to the feature removal
file).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16396 .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: tomas m <tmezzadra@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
pavel@suse.cz no longer works, replace it with working address.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The ACPI spec tells us that the firmware will reenable SCI_EN on resume.
Reality disagrees in some cases. The ACPI spec tells us that the only way
to set SCI_EN is via an SMM call.
https://bugzilla.kernel.org/show_bug.cgi?id=13745 shows us that doing so
may break machines. Tracing the ACPI calls made by Windows shows that it
unconditionally sets SCI_EN on resume with a direct register write, and
therefore the overwhelming probability is that everything is fine with
this behaviour.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce kernel parameter acpi_sleep=sci_force_enable
some laptop requires SCI_EN being set directly on resume,
or else they hung somewhere in the resume code path.
We already have a blacklist for these laptops but we still need
this option, especially when debugging some suspend/resume problems,
in case there are systems that need this workaround and are not yet
in the blacklist.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Always save the value of EFER, regardless of the state of NX. Since
EFER may not actually exist, use rdmsr_safe() to do so.
v2: check the return value from rdmsr_safe() instead of relying on
the output values being unchanged on error.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@tuxonice.net>
LKML-Reference: <1258154897-6770-3-git-send-email-hpa@zytor.com>
Acked-by: Kees Cook <kees.cook@canonical.com>
Instead of using bootmem, try find_e820_area()/reserve_early(),
and call acpi_reserve_memory() early, to allocate the wakeup
trampoline code area below 1M.
This is more reliable, and it also removes a dependency on
bootmem.
-v2: change function name to acpi_reserve_wakeup_memory(),
as suggested by Rafael.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: pm list <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4AFA210B.3020207@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
One of the numbers in arch/x86/kernel/acpi/sleep.c is long, but it is
not annotated appropriately, so sparese warns about it. Fix that.
[rjw: added the changelog.]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Fix two compilation warnings in drivers/acpi/sleep.c, one triggered
by unsetting CONFIG_SUSPEND and the other triggered by unsetting
CONFIG_HIBERNATION, by moving some code under the appropriate
#ifdefs .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Do the following cleanups:
* kill x86_64_init_pda() which now is equivalent to pda_init()
* use per_cpu_offset() instead of cpu_pda() when initializing
initial_gs
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ Based on original patch from Christoph Lameter and Mike Travis. ]
CPU startup code in head_64.S loaded address of a zero page into %gs
for temporary use till pda is loaded but address to the actual pda is
available at the point. Load the real address directly instead.
This will help unifying percpu and pda handling later on.
This patch is mostly taken from Mike Travis' "x86_64: Fold pda into
per cpu area" patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
On some machines it may be necessary to disable the saving/restoring
of the ACPI NVS memory region during hibernation/resume. For this
purpose, introduce new ACPI kernel command line option
acpi_sleep=s4_nonvs.
Based on a patch by Zhang Rui.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Nigel Cunningham <nigel@tuxonice.net>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
x86 ACPI: Fix breakage of resume on 64-bit UP systems with SMP kernel
We are now using per CPU GDT tables in head_64.S and the original
early_gdt_descr.address is invalidated after boot by
setup_per_cpu_areas(). This breaks resume from suspend to RAM on
x86_64 UP systems using SMP kernels, because this part of head_64.S
is also executed during the resume and the invalid GDT address
causes the system to crash. It doesn't break on 'true' SMP systems,
because early_gdt_descr.address is modified every time
native_cpu_up() runs. However, during resume it should point to the
GDT of the boot CPU rather than to another CPU's GDT.
For this reason, during suspend to RAM always make
early_gdt_descr.address point to the boot CPU's GDT.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=11568, which
is a regression from 2.6.26.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Reported-and-tested-by: Andy Wettstein <ajw1980@gmail.com>
x86_64 SMP suspend to RAM uses a 10k temporary stack for saving the
kernel state, but only 4k of it is used. Shrink it to 4k.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Len Brown <len.brown@intel.com>
x86_64 SMP suspend to RAM uses a 10k temporary stack for saving the
kernel state, but only 4k of it is used. Shrink it to 4k.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
arch/x86/power/cpu_32.c __save_processor_state calls read_cr4()
only a i486 CPU doesn't have the CR4 register. Trying to read it
produces an invalid opcode oops during suspend to disk.
Use the safe rc4 reading op instead. If the value to be written is
zero the write is skipped.
arch/x86/power/hibernate_asm_32.S
done: swapped the use of %eax and %ecx to use jecxz for
the zero test and jump over store to %cr4.
restore_image: s/%ecx/%eax/ to be consistent with done:
In addition to __save_processor_state, acpi_save_state_mem,
efi_call_phys_prelog, and efi_call_phys_epilog had checks added
(acpi restore was in assembly and already had a check for
non-zero). There were other reads and writes of CR4, but MCE and
virtualization shouldn't be executed on a i486 anyway.
Signed-off-by: David Fries <david@fries.net>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/acpi/sleep.c:24: warning: 'temp_stack' defined but not used
[ Sven Wegener <sven.wegener@stealer.net>: fix build bug ]
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ACPI defines a hardware signature. BIOS calculates the signature according to
hardware configure and if hardware changes while hibernated, the signature
will change. In that case, S4 resume should fail.
Still, there may be systems on which this mechanism does not work correctly,
so it is better to provide a workaround for them. For this reason, add a new
switch to the acpi_sleep= command line argument allowing one to disable
hardware signature checking.
[shaohua.li@intel.com: build fix]
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <Valdis.Kletnieks@vt.edu>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge the GDT_ENTRY() macro between arch/x86/boot/pm.c and
arch/x86/kernel/acpi/sleep.c and put the new one in
<asm-x86/segment.h>.
While we're at it, correct the bitmasks for the limit and flags. The
new version relies on using ULL constants in order to cause type
promotion rather than explicit casts; this avoids having to include
<linux/types.h> in <asm-x86/segments.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
Explain that we set up the descriptors for Big Real Mode, and why we
do so. In particular, one system that is known to fail without it is
the Lenovo X61.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The explanation for recent video BIOS suspend quirk failures is that
the VESA BIOS expects to be entered in Big Real Mode (*.limit = 0xffffffff)
instead of ordinary Real Mode (*.limit = 0xffff).
This patch changes the segment descriptors to Big Real Mode instead.
The segment descriptor registers (what Intel calls "segment cache") is
always active. The only thing that changes based on CR0.PE is how it is
*loaded* and the interpretation of the CS flags.
The segment descriptor registers contain of the following sub-registers:
selector (the "visible" part), base, limit and flags. In protected mode
or long mode, they are loaded from descriptors (or fs.base or gs.base can
be manipulated directly in long mode.) In real mode, the only thing
changed by a segment register load is the selector and the base, where the
base <- selector << 4. In particular, *the limit and the flags are not
changed*.
As far as the handling of the CS flags: a code segment cannot be writable
in protected mode, whereas it is "just another segment" in real mode, so
there is some kind of quirk that kicks in for this when CR0.PE <- 0. I'm
not sure if this is accomplished by actually changing the cs.flags register
or just changing the interpretation; it might be something that is
CPU-specific. In particular, the Transmeta CPUs had an explicit "CS is
writable if you're in real mode" override, so even if you had loaded CS
with an execute-only segment it'd be writable (but not readable!) on return
to real mode. I'm not at all sure if that is how other CPUs behave.
Signed-off-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/acpi/sleep.c: In function ‘acpi_save_state_mem':
arch/x86/kernel/acpi/sleep.c:75: error: ‘stack_start' undeclared (first use in this function)
arch/x86/kernel/acpi/sleep.c:75: error: (Each undeclared identifier is reported
only once
arch/x86/kernel/acpi/sleep.c:75: error: for each function it appears in.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
call x86_64's init_rsp stack_start, just as i386 does.
Put a zeroed stack segment for consistency. With this,
we can eliminate one ugly ifdef in smpboot.c.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some Dell laptops enter resume with apparent garbage in the segment
descriptor registers (almost certainly the result of a botched
transition from protected to real mode.) The only way to clean that
up is to enter protected mode ourselves and clean out the descriptor
registers.
This fixes resume on Dell XPS M1210 and Dell D620.
Reference: http://bugzilla.kernel.org/show_bug.cgi?id=10927
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: pm list <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
ACPI PM: Add possibility to change suspend sequence
There are some systems out there that don't work correctly with
our current suspend/hibernation code ordering. Provide a workaround
for these systems allowing them to pass 'acpi_sleep=old_ordering' in
the kernel command line so that it will use the pre-ACPI 2.0 ("old")
suspend code ordering.
Unfortunately, this requires us to add a platform hook to the
resuming of devices for recovering the platform in case one of the
device drivers' .suspend() routines returns error code. Namely,
ACPI 1.0 specifies that _PTS should be called before suspending
devices, but _WAK still should be called before resuming them in
order to undo the changes made by _PTS. However, if there is an
error during suspending devices, they are automatically resumed
without returning control to the PM core, so the _WAK has to be
called from within device_resume() in that cases.
The patch also reorders and refactors the ACPI suspend/hibernation
code to avoid duplication as far as reasonably possible.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Move wakeup code to .c, so that video mode setting code can be shared
between boot and wakeup. Remove nasty assembly code in 64-bit case by
re-using trampoline code. Stack setup was fixed to clear high 16bits
of %esp, maybe that fixes some machines.
.c code sharing and morse code was done H. Peter Anvin, Sam Ravnborg
reviewed kbuild related stuff, and it seems okay to him. Rafael did
some cleanups.
[rjw:
* Made the patch stop breaking compilation on x86-32
* Added arch/x86/kernel/acpi/sleep.h
* Got rid of compiler warnings in arch/x86/kernel/acpi/sleep.c
* Fixed 32-bit compilation on x86-64 systems
* Added include/asm-x86/trampoline.h and fixed the non-SMP
compilation on 64-bit x86
* Removed arch/x86/kernel/acpi/sleep_32.c which was not used
* Fixed some breakage caused by the integration of smpboot.c done
under us in the meantime]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Unify arch/x86/kernel/acpi/sleep*.c
Pretty trivial unification; when two functions differed, it was
usually in error handling, and better of the two was picked up.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Looks-okay-to: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Len Brown