The Orange Pi Plus is a SBC based on the Allwinner H3 SoC
with 8GB eMMC, multiple USB ports through a USB hub chip, SATA through
a USB-SATA bridge, one uSD slot, a 10/100/1000M ethernet port,
WiFi, HDMI, headphone jack, IR receiver, a microphone, a CSI connector
and a 40-pin GPIO header.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This baseboard from SWAC is equipped with the ICnova-A20 SoM from
Incircuit. This board is equipped with the following interfaces /
devices:
- 512 MiB SDRAM
- 4 GiB MLC NAND (Micron MT29F32G08CBACAWP or Hynix H27UBG8T2BTR)
- USB host
- LCD 800x480
- HDMI
- CAN
Note that the NAND support is still missing. As its currently not
supported in mainline for sunxi and especially for these MLC
devices.
The original plan was to also provide a dtsi for the ICnova SoM,
to put all the SoM internal nodes / properties there. But as I
don't have a clear overview of the SoM specific and baseboard
specific differences, I'm putting all in one dts for now. Once
somebody pushed support for some other baseboard using the
A20 SoM from Incircuit (e.g. the ADB4006 reference design), this
should be separated.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marcus Heuer <marcus.heuer@swac.de>
[maxime: Fixed CPU regulator upper voltage boundary]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
Again we have a sizable (but not huge) cleanup branch with a net delta of about
-3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now gone
completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the above are
the major pieces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uI7R
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"Again we have a sizable (but not huge) cleanup branch with a net delta
of about -3k lines.
Main contents here is:
- A bunch of development/cleanup of a few PXA boards
- Removal of bockw platforms on shmobile, since the platform has now
gone completely multiplatform. Whee!
- move of the 32kHz timer on OMAP to a proper timesource
- Misc cleanup of older OMAP material (incl removal of one board
file)
- Switch over to new common PWM lookup support for several platforms
There's also a handful of other cleanups across the tree, but the
above are the major pieces"
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (103 commits)
ARM: OMAP3: hwmod data: Remove legacy mailbox data and addrs
ARM: DRA7: hwmod data: Remove spinlock hwmod addrs
ARM: OMAP4: hwmod data: Remove spinlock hwmod addrs
ARM: DRA7/AM335x/AM437x: hwmod: Remove gpmc address space from hwmod data
ARM: Remove __ref on hotplug cpu die path
ARM: Remove open-coded version of IRQCHIP_DECLARE
arm: omap2: board-generic: use omap4_local_timer_init for AM437x
ARM: DRA7/AM335x/AM437x: hwmod: Remove elm address space from hwmod data
ARM: OMAP: Remove duplicated operand in OR operation
clocksource: ti-32k: make it depend on GENERIC_CLOCKSOURCE
ARM: pxa: remove incorrect __init annotation on pxa27x_set_pwrmode
ARM: pxa: raumfeld: make some variables static
ARM: OMAP: Change all cpu_is_* occurences to soc_is_* for id.c
ARM: OMAP2+: Rename cpu_is macros to soc_is
arm: omap2: timer: limit hwmod usage to non-DT boots
arm: omap2+: select 32k clocksource driver
clocksource: add TI 32.768 Hz counter driver
arm: omap2: timer: rename omap_sync32k_timer_init()
arm: omap2: timer: always call clocksource_of_init() when DT
arm: omap2: timer: move realtime_counter_init() around
...
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all dtbs
in the tree for most arches with dts files (except powerpc for now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tGCy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A fairly large (by DT standards) pull request this time with the
majority being some overdue moving DT binding docs around to
consolidate similar bindings.
- DT binding doc consolidation moving similar bindings to common
locations. The majority of these are display related which were
scattered in video/, fb/, drm/, gpu/, and panel/ directories.
- Add new config option, CONFIG_OF_ALL_DTBS, to enable building all
dtbs in the tree for most arches with dts files (except powerpc for
now).
- OF_IRQ=n fixes for user enabled CONFIG_OF.
- of_node_put ref counting fixes from Julia Lawall.
- Common DT binding for wakeup-source and deprecation of all similar
bindings.
- DT binding for PXA LCD controller.
- Allow ignoring failed PCI resource translations in order to ignore
64-bit addresses on non-LPAE 32-bit kernels.
- Support setting the NUMA node from DT instead of only from parent
device.
- Couple of earlycon DT parsing fixes for address and options"
* tag 'devicetree-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (45 commits)
MAINTAINERS: update DT binding doc locations
devicetree: add Sigma Designs vendor prefix
of: simplify arch_find_n_match_cpu_physical_id() function
Documentation: arm: Fixed typo in socfpga fpga mgr example
Documentation: devicetree: fix reference to legacy wakeup properties
Documentation: devicetree: standardize/consolidate on "wakeup-source" property
drivers: of: removing assignment of 0 to static variable
xtensa: enable building of all dtbs
mips: enable building of all dtbs
metag: enable building of all dtbs
metag: use common make variables for dtb builds
h8300: enable building of all dtbs
arm64: enable building of all dtbs
arm: enable building of all dtbs
arc: enable building of all dtbs
arc: use common make variables for dtb builds
of: add config option to enable building of all dtbs
of/fdt: fix error checking for earlycon address
of/overlay: add missing of_node_put
of/platform: add missing of_node_put
...
Enable building all dtb files when CONFIG_OF_ALL_DTBS is enabled. The dtbs
are not really dependent on a platform being enabled or any other kernel
config, so for testing coverage it is convenient to build all of the dtbs.
This builds all dts files in the tree, not just targets listed. This
is simpler for arm64 which has a bunch of sub-dirs.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
This pull request contains the DT changes for BCM2835 in 4.4. It
pulls in clk/clk-bcm2835 (which Stephen Boyd has said would be stable)
because the DT changes to enable the clock driver need the driver
itself to be present. These changes include the following:
- Eric Anholt, moves the bcm2835 clock driver under bcm/ where it belongs with
other Broadcom clock providers drivers, defines the binding for new clock
driver, adds support for programming the BCM2835 audio domain, adds the DDC I2C
controller to Device Tree, and finally migrates the Device Tree to use the new
clock driver binding
- Lubomir Rintel adds support for the Raspberry Pi Model A+ and B revision 2, and
remove the I2S controller which is non-existent on Raspberry Pi Model B
- Stefan Wahren adds an uart0 label for referencing the UART adapter
* tag 'arm/soc/for-4.4/rpi-dt-v2' of https://github.com/Broadcom/stblinux:
ARM: bcm2835: Add the DDC I2C controller to the device tree.
ARM: bcm2835: Switch to using the new clock driver support.
ARM: bcm2835: dt: Add Raspberry Pi Model A+
ARM: bcm2835: dt: Add Raspberry Pi Model B rev2
ARM: bcm2835: dt: Raspberry Pi Model B had no I2S
ARM: bcm2835: add label for uart0
clk: bcm2835: Add support for programming the audio domain clocks
clk: bcm2835: Add binding docs for the new platform clock driver.
clk: bcm2835: Move under bcm/ with other Broadcom SoC clk drivers.
Signed-off-by: Olof Johansson <olof@lixom.net>
up some omap5 issues to allow adding other omap5 boards. Also some other
fixes and clean-up:
- Fix SDIO WLAN for omap5 that's been broken for a while. As further
patches are still needed for wl18xx, no need for stable on this one.
- Move most of omap5 support into omap5-board-common.dtsi as most omap5
boards seem to share the same basic set of devices.
- Add minimal IGEPv5 support using based on omap5-board-common.dtsi
- Remove now unneedes gpio hogging for dra72-evm
- Update Javier Martinez Canillas email address
- Change earlier IGEP boards to use IOPAD pinmux macros
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2bcN
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap dts changes for v4.4 merge window, part 2" from Tony Lindgren:
Few more omap dts changes for v4.4 merge window, mostly to fix and clean
up some omap5 issues to allow adding other omap5 boards. Also some other
fixes and clean-up:
- Fix SDIO WLAN for omap5 that's been broken for a while. As further
patches are still needed for wl18xx, no need for stable on this one.
- Move most of omap5 support into omap5-board-common.dtsi as most omap5
boards seem to share the same basic set of devices.
- Add minimal IGEPv5 support using based on omap5-board-common.dtsi
- Remove now unneedes gpio hogging for dra72-evm
- Update Javier Martinez Canillas email address
- Change earlier IGEP boards to use IOPAD pinmux macros
* tag 'omap-for-v4.4/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-base0033: Use IOPAD pinmux macro
ARM: dts: am335x-igep0033: Use IOPAD pinmux macro
ARM: dts: omap3-igep0020: Use IOPAD pinmux macro
ARM: dts: am437x-gp-evm: Add wakeup interrupt source for pixcir_i2c_ts
ARM: dts: Update Javier Martinez Canillas's email
ARM: dts: dra72-evm: remove cpsw gpio hogging and add mode-gpios
ARM: dts: Add basic support for isee igepv5
ARM: dts: Move most of omap5-uevm.dts to omap5-board-common.dtsi
ARM: dts: Fix WLAN regression on omap5-uevm
- Add IOMUXC LPSR (Low Power State Retention) device for i.MX7D.
- Add a few low power mode related devices and touch controller for
i.MX6UL.
- Add a number of devices for i.MX7D SDB board support, USB, Dual FEC,
and eMMC5.0.
- i.MX6 Boundary Devices updates: relicense under GPLv2/X11, add Okaya
LCD, touch and wifi support, add new boards Nitrogen6_Lite and
Nitrogen6_Max.
- Enable touch screen and NAND Flash controller for a few Vybrid
devices.
- Some random and small updates on LS1021A and MXS support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWJQUPAAoJEFBXWFqHsHzOo+cH/irx+abVdFV97q6M0VwFsQ3/
Tf4/CsdiTjM5ZDrKZEtXzP8BZl+ZO4tQXLspP+wVceQ+PVUiVvdAHu0l68iuJRrA
+Bj9VrLIzMDf7FVpzbZHZD3kd1NALGh/5i0TerkuZMNl1KH57HyGjLnjKH43n7uz
mFPeZFAQMwSjEnRJj/6217Itqi+LurARJsnXQs6uhQ7feSsA88HU3EQ8QsiZqiAu
MULAJBYaE09shlokuXIKx67t8outdb8C0Uue64nt42y8NR0m5eVVG7NJoF+23T6C
CRX5zveYa7D2QXTkihvjdRpazhLiPnwV3RCVejLOZMk0G14hD9U39jkTp+9ws1w=
=kPBq
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree changes for 4.4:
- Add IOMUXC LPSR (Low Power State Retention) device for i.MX7D.
- Add a few low power mode related devices and touch controller for
i.MX6UL.
- Add a number of devices for i.MX7D SDB board support, USB, Dual FEC,
and eMMC5.0.
- i.MX6 Boundary Devices updates: relicense under GPLv2/X11, add Okaya
LCD, touch and wifi support, add new boards Nitrogen6_Lite and
Nitrogen6_Max.
- Enable touch screen and NAND Flash controller for a few Vybrid
devices.
- Some random and small updates on LS1021A and MXS support.
* tag 'imx-dt-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (53 commits)
ARM: dts: ls1021a: Add quirk for Erratum A009116
ARM: imx6sx-sdb: Fix typo in regulator enable GPIO property
ARM: dts: imx6: phyFLEX: fix typo in "pinctrl-names"
ARM: dts: imx6: change the core clock of spdif
ARM: dts: vf-colibri: enable NAND flash controller
ARM: dts: vf610twr: add NAND flash controller peripherial
ARM: dts: imx: add Boundary Devices Nitrogen6_Lite board
ARM: dts: imx: add Boundary Devices Nitrogen6_Max board
ARM: dts: imx6dl-nitrogen6x: change manufacturer to Boundary Devices
ARM: dts: imx6q-nitrogen6x: change manufacturer to Boundary Devices
of: Add Boundary Devices Inc. vendor prefix
ARM: dts: imx6qdl-sabrelite: relicense under GPLv2/X11
ARM: dts: imx6qdl-nitrogen6x: relicense under GPLv2/X11
ARM: dts: imx6qdl-nitrogen6x: add wifi wl1271 support
ARM: dts: imx6dql-nitrogen6x: add touchscreen support
ARM: dts: imx6qdl-sabrelite: add Okaya LCD panel
ARM: dts: imx6qdl-nitrogen6x: add Okaya LCD panel
ARM: dts: vf500-colibri: Add device tree node for touchscreen support
ARM: dts: i.MX35: fix cpu compatible value
ARM: dts: i.MX31: fix cpu compatible value
...
Signed-off-by: Olof Johansson <olof@lixom.net>
More DT patches for 4.4, mostly with new boards coming in (CHIP, BananaPi
M2, pcduino2), further consolidation for the q8-based designs and a bunch
of random patches enhancing support for existing boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vcTX
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Allwinner DT changes for 4.4, round 2
More DT patches for 4.4, mostly with new boards coming in (CHIP, BananaPi
M2, pcduino2), further consolidation for the q8-based designs and a bunch
of random patches enhancing support for existing boards
* tag 'sunxi-dt-for-4.4-2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (27 commits)
ARM: dts: sun6i: Add a dts file for the Sinovoip BPI-M2 board
ARM: dts: sun6i: Add mmc2_pins_a pinmux setting to sun6i-a31.dtsi
ARM: dts: sunxi: Fix interrupt-cells for [r]pio on A23/A31/A33/A80
ARM: dts: sun8i: Add NMI interrupt controller node
ARM: dts: sun6i: hummingbird: Enable AXP221 DC5LDO regulator as "vdd-cpus"
ARM: dts: sun6i: hummingbird: Use axp22x.dtsi for AXP221 regulators
ARM: dts: sun6i: hummingbird: Fix VDD-CPU and VDD-GPU regulator names
ARM: dts: sun7i: Add regulator configuration for pcDuino v3 Nano
ARM: dts: sun6i: Turn on gmac on Colombus
ARM: dts: sun8i: Make et-q8-v1.6.dts a symlink to q8-tablet.dts
ARM: dts: sun8i: Make ippo-q8h-v*.dts a symlink to q8-tablet.dts
ARM: dts: sun8i: Add sun8i-a23-q8-tablet.dts file
ARM: dts: sun5i: Add backlight node to sun5i-q8-common.dtsi
ARM: dts: sunxi: Enable PWM controller on Q8 format tablets
ARM: dts: sun5i: Add PWM channel 0 pinmux setting for A13/A10s
ARM: dts: sun5i: Add PWM controller node for A13 / A10s
ARM: sun5i: Add C.H.I.P DTS
ARM: dts: sunxi: Add dtsi for AXP22x PMIC
ARM: dts: sun7i: Correct USB regulators on pcDuino v3 Nano
ARM: sun5i: dt: Add UART3 CTS and RTS pins
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The MSI Primo81 is an A31s based tablet, with 1G RAM, 16G NAND,
768x1024 IPS LCD display, mono speaker, 0.3 MP front camera, 2.0 MP
rear camera, 3500 mAh battery, gt911 touchscreen, mma8452 accelerometer
and rtl8188etv usb wifi. Has "power", "volume+" and "volume-" buttons
(both volume buttons are also connected to the UBOOT_SEL pin). The
external connectors are represented by MicroSD slot, MiniHDMI, MicroUSB
OTG and 3.5mm headphone jack.
USB OTG is enabled in host only mode. AXP221 USB power supply and
GPIO support are required for full USB OTG support.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Karsten Merker <merker@debian.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Add support for severals Armada-370-based Seagate NAS
- Fix Ready NAS device tree
- Modify SDHCI binding for A388-GP allowing using it on old and new
version of the board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlYhOjIACgkQCwYYjhRyO9VTWACeJDBHZ1+ojF5irnZzNe/9PKaF
zJQAnjBmJxI1auTY+SQHVkZN3w2HOhwU
=Dvfj
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.4-2' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.4 (part 2)
- Add support for severals Armada-370-based Seagate NAS
- Fix Ready NAS device tree
- Modify SDHCI binding for A388-GP allowing using it on old and new
version of the board
* tag 'mvebu-dt-4.4-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: set SW polling as SDHCI card detection on A388-GP
arm: mvebu: reorder nodes under internal-regs by address in RN2120 .dts file
arm: mvebu: disable unused Armada RTC on ReadyNAS 102, 104 and 2120
ARM: mvebu: add DT support for Seagate Personal Cloud
ARM: mvebu: add DT support for Seagate NAS 2 and 4-Bay
Signed-off-by: Olof Johansson <olof@lixom.net>
The Point of View protab2-ips9 is a tablet with a 9" ips 1024x768 lcd screen,
microsd slot, headphones, mini hdmi, mini usb b and power barrel connectors.
It uses a rtl8188cus usb wifi chip and a RDA 5875Y bluetooth chip attached
to uart2. It has a bma250 accelerometer attached to i2c1 addr 0x18, this
only works when ldo3 is set to 2.8 volt, otherwise i2c1 gets stuck, so
for now we mark i2c1 as failed.
It has a pixcir,pixcir_tangoc compatible touchscreen attached to i2c2 addr
0x5c. This is not enabled in this dts, because this variant of the
pixcir_tangoc has separate wakeup and enable pins both of which need
to be driven low before the touchscreen will work. Before we can enable
this the pixcir driver and devicetree-bindings need to be extended to
support these pins.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Sinlinx A31s SDK is a A31s based module/baseboard development kit.
The core module has the SoC, PMIC, DRAM, eMMC and supporting components.
There are also pads for UART0, JTAG and I2S.
The baseboard has 100 Mbps Ethernet, 5x USB 2.0 host ports via a USB 2.0
hub chip, MMC, HDMI, SPDIF, CIR, audio jacks, 2 tablet-like volume
buttons, RS232 style UART and USB OTG (though VBUS is not connected).
Various headers are available for other addon modules, such as SDIO
WiFi, LCD display, camera sensor, UARTs, I2C, SPI and GPIOs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Based on i.MX6 Quad with 4GB of DDR3.
http://boundarydevices.com/product/nitrogen6max/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Sinovoip BPI-M2 is a SBC board based on the A31s SoC it features
1G RAM, a microsd slot, Gbit ethernet, 4 usb-a USB-2 ports, ir receiver,
stereo headphone jack and hdmi video output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With omap5-board-common.dtsi, we can now easily add support for various omap5
board variants. Let's add minimal support for isee igepv5.
So far I've tested that basic things work, such as serial, USB Ethernet, HDMI
and WLAN.
Note that like omap5-uevm, these boards seem to need to reserve 16MB for a
trap section as in commit 03178c66d2 ("ARM: dts: omap5-evm: Update
available memory to 2032 MB") and also noted in a u-boot commit at
http://marc.info/?l=u-boot&m=134376852603255 and also at
http://patchwork.ozlabs.org/patch/159881/.
Not sure why this is not needed for omap5-cm-t54.dts, maybe because of
different u-boot configuration.
Signed-off-by: Tony Lindgren <tony@atomide.com>
- DCAN sleep pins for am437x-gp-evm
- A series of changes to add audio support for dra7
- Add support for gpio keys and LEDs on dra7
- Regulator clean-up for am335x-wega
- A series of changes to enable IOMMUs and mailboxes for dra7
accelerators
- Add support for am335x-bonegreen
- Fix up GPIO flags where 0 was used instead of GPIO_ACTIVE_HIGH
- Fix omap3-lilly-am33x IRQ level flag
- Remove duplicate uart2 pinmux for igep and fix indentation and
update igep to use pinctrl macros for the register offsets
- Fix MMC cd-gpios usage
Note that this branch is against v4.3-rc4 as that contains critical
MMC related fixes to boot with MMC working on most omaps.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Sbup
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.4/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Device tree changes for omaps for v4.4 merge window:" from Tony Lindgren:
- DCAN sleep pins for am437x-gp-evm
- A series of changes to add audio support for dra7
- Add support for gpio keys and LEDs on dra7
- Regulator clean-up for am335x-wega
- A series of changes to enable IOMMUs and mailboxes for dra7
accelerators
- Add support for am335x-bonegreen
- Fix up GPIO flags where 0 was used instead of GPIO_ACTIVE_HIGH
- Fix omap3-lilly-am33x IRQ level flag
- Remove duplicate uart2 pinmux for igep and fix indentation and
update igep to use pinctrl macros for the register offsets
- Fix MMC cd-gpios usage
Note that this branch is against v4.3-rc4 as that contains critical
MMC related fixes to boot with MMC working on most omaps.
* tag 'omap-for-v4.4/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (33 commits)
ARM: dts: omap3-igep: Use OMAP3_CORE1_IOPAD pinmux macro
ARM: dts: dra7xx: am57xx: fix cd-gpios definition as per hardware design and dt binding docs
ARM: dts: am43xx: fix cd-gpios definition as per hardware design and dt binding docs
ARM: dts: am335x: fix cd-gpios definition as per hardware design and dt binding docs
ARM: dts: omap3-igep0020: Remove duplicate uart2 pinmux
ARM: dts: omap3-igep: Fix indentation
ARM: dts: omap3-lilly-a83x: Don't use IRQ level flag for a GPIO
ARM: dts: DRA74x: Add IOMMU nodes for DSP2
ARM: dts: DRA7: Add common IOMMU nodes
ARM: dts: DRA74x: Add dsp2_system syscon node
ARM: dts: DRA7: Add dsp1_system syscon node
ARM: dts: Use defined GPIO constants in flags cell for OMAP2+ boards
ARM: dts: Add am335x-bonegreen
ARM: dts: beagle-x15: Enable the system mailboxes 5 and 6
ARM: dts: dra72-evm: Enable the system mailboxes 5 and 6
ARM: dts: dra7-evm: Enable the system mailboxes 5 and 6
ARM: dts: DRA72x: Add IPC sub-mailbox nodes for IPU1, IPU2 & DSP1
ARM: dts: DRA74x: Add IPC sub-mailbox nodes for all IPUs & DSPs
ARM: dts: am335x-wega: Clean up regulators
ARM: dts: dra7-evm: add gpio key support
...
- New board support
: add exynos5250-snow-rev5 DT file to support Snow Rev5+ board
: add exynos5422-odroidxu4 DT file to support Odroid XU4 board
: split exynos5422-odroidxu3-audio DT file from odroidxu3-common
- USE GPIO constants for flags cells for exynos boards
- fix cpu compatible value to 'arm926ej-s' for s3c2416
- add DMA support for serial ports for exynos4
- add suspend opp for exynos4412
- remove regulator-compatible usage for exynos4412-trats2
- enable EC vboot context support for Peach boards
- move display-timings node to DP for exynos5250-arndale, smdk5250 and smdk5420
- for exynos4412-odroid/odroidu3
: unify voltage regulator style and
: remove redundant pinctrl settings
: add pwm-fan node and use it as a colling device
- for exynos5422-odroidxu3
: fix power off method and LEDs
- dt-bindings
: grounded AC0KB pin on S2MPS11
: entry how to use PWM FAN as a cooling device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJWHBBhAAoJEA0Cl+kVi2xqTYEP/jutsYKeQE2/A3g3zOMHfuYv
p6Q9m0RB5rug7KOmT10nqAJmBpj3FZZgSTWf3AUfPCNxzei1DY9LNknHPqOIHY4S
HfbDx0qA2U5Jta02Bo9SE3pgkODJX/p1YAmiEbVOwiKS6vuFysykX0QvidBSCYbk
tqfqb6LRsdglIItKs2acUyLoZeldaYdDOvkL6hrHiwjz8njUGoSYLITkorfrBSIv
jcppiOXAZqxsjgmEho86u7jbqbC66a3yH9bMgge45t98rE5vu3WIoA8082jlQXpt
JnGtNfaTb8DECwL7T0++Ohk8hsDHood3WEmuoYAHUEq5DMotS//LZ4n2xDNWXVbN
s//cRrETBIMWk/AUZdNYbtbNGVOKYz78xL7EiJSBYby+YdYFi3tpRJ0/+9bHEglD
URwxOUb1320S2QlFULN+50x6VxPPbbAU1EmFH708RXDFQIJMLFUIANGfck0CuFah
PJaAChyAMLbqV9K7y/FfqDobxZAa1y2eAYWyL4eLYfxeOhY+PhhRfMD8pWgY1ZW4
vgHqpVADJvuZ5d7U3JgYclTQ0J6ILrDoCP5/E5C9TvYkBP5SV4KiEqvZ2Hklzxv7
9vdsfWppnYRTH2moo0tokLNRYXewzW7svq/gKYXY0VjERjnmCfrjMRXZ76q3WQ7Y
gy2KJDH/jxwlIdsGEDG6
=FqOp
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v4.4" from Kukjin Kim:
- New board support
: add exynos5250-snow-rev5 DT file to support Snow Rev5+ board
: add exynos5422-odroidxu4 DT file to support Odroid XU4 board
: split exynos5422-odroidxu3-audio DT file from odroidxu3-common
- USE GPIO constants for flags cells for exynos boards
- fix cpu compatible value to 'arm926ej-s' for s3c2416
- add DMA support for serial ports for exynos4
- add suspend opp for exynos4412
- remove regulator-compatible usage for exynos4412-trats2
- enable EC vboot context support for Peach boards
- move display-timings node to DP for exynos5250-arndale, smdk5250 and smdk5420
- for exynos4412-odroid/odroidu3
: unify voltage regulator style and
: remove redundant pinctrl settings
: add pwm-fan node and use it as a colling device
- for exynos5422-odroidxu3
: fix power off method and LEDs
- dt-bindings
: grounded AC0KB pin on S2MPS11
: entry how to use PWM FAN as a cooling device
* tag 'samsung-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (22 commits)
ARM: dts: Use GPIO constants for flags cells in exynos5440 boards
ARM: dts: Use GPIO constants for flags cells in exynos5420/5422/5800 boards
ARM: dts: Use GPIO constants for flags cells in exynos4412 boards
ARM: dts: Use GPIO constants for flags cells in exynos4120 boards
ARM: dts: Use GPIO constants for flags cells in exynos3250 boards
ARM: dts: Enable EC vboot context support on Peach boards
ARM: dts: Remove regulator-compatible usage in exynos4412-trats2
ARM: dts: Move display-timings node from fimd to dp in exynos5250-arndale, smdk5250 and smdk5420
ARM: dts: Add Exynos5250 Snow Rev5+ support on exynos5250-snow-rev5
ARM: dts: Unify voltage regulator style in exynos4412-odroid
ARM: dts: Remove redundant pinctrl settings in exynos4412-odroid
ARM: dts: Fix cpu compatible value for s3c2416
ARM: dts: Add support Odroid XU4 board for exynos5422-odroidxu4
ARM: dts: Split audio configuration to separate exynos5422-odroidxu3-audio
ARM: dts: Fix power off method for exynos5422-odroidxu3-common
dt-bindings: Document grounded ACOKB pin on S2MPS11
ARM: dts: use pwm-fan device as a cooling device for exynos4412-odroidu3
ARM: dts: Add pwm-fan node for exynos4412-odroidu3
dt-bindings: Documentation entry to explain how to use PWM FAN as a cooling device
ARM: dts: add suspend opp to exynos4412
...
DT patches for the 4.4 merge window, most notably:
- Enable the OTG controller on more boards
- Create new DTSI for the q8's design
- Added RSB support to the A23 and A33 SoCs
- New boards: Olimex A20 EVB, Yones bs1078v2
Plus the usual random patches enabling and / or enhancing a few things in
particular boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Q2Q4
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Pull "Allwinner DT changes for 4.4" from Maxime Ripard:
DT patches for the 4.4 merge window, most notably:
- Enable the OTG controller on more boards
- Create new DTSI for the q8's design
- Added RSB support to the A23 and A33 SoCs
- New boards: Olimex A20 EVB, Yones bs1078v2
Plus the usual random patches enabling and / or enhancing a few things in
particular boards.
* tag 'sunxi-dt-for-4.4' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (59 commits)
ARM: dts: sun6i: hummingbird: Drop AXP221 DC1SW and DC5LDO supplies
ARM: dts: sun8i: sinlinx-sina33: Enable Reduced Serial Bus controller
ARM: dts: sun8i: q8-common: Enable RSB controller for A23/A33 Q8 tablets
ARM: dts: sun8i: Add Reduced Serial Bus controller device node to A23/A33 dtsi
ARM: dts: sun4i: Add AXP209 PMU regulators for pcDuino1/2
ARM: sun7i: dt: Add new Olimex A20 EVB device
ARM: dts: sun6i: hummingbird: Add aliases for rtc devices
ARM: dts: sun7i: Add dts file for Wits Pro A20 DKT
ARM: dts: sun7i: Enable USB DRC on Wexler TAB7200
ARM: dts: sun7i: Enable USB DRC on the Orange pi
ARM: dts: sun7i: Enable USB DRC on orangepi-mini
ARM: dts: axp209: Add usb_power_supply child node to the ax209 node
ARM: dts: sun8i: Make ippo-q8h-v1.2.dts a symlink to q8-tablet.dts
ARM: dts: sun8i: Add sun8i-a33-q8-tablet.dts file
ARM: dts: sun6i: Add support for Yones Toptech bs1078v2 tablets
ARM: dts: sun4i: Enable USB DRC on the Marsboard A10
ARM: dts: sun4i: gemei-g9: Add accelerometer (bma250) IRQ
ARM: dts: sun8i-a33: Add security system crypto engine clock and device nodes
ARM: dts: sun8i: Add pwm-backlight device for A23/A33 Q8 format tablets
ARM: sun8i: A23: Add missing msgbox gate
...
This is a generic dts file for A23 based q8 formfactor tablets,
this is intended to replace both sun8i-a23-ippo-q8h-v5.dts and
sun8i-a23-ippo-q8h-v1.2.dts (these can be fully dropped after a
transition period).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus
the HDMI port and addition of two Grove connectors (i2c2 and usart2).
This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom:
1A: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|]
http://beagleboard.org/greenhttp://www.seeedstudio.com/wiki/Beaglebone_green
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Jason Kridner <jkridner@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds DT support for the Seagate Personal Cloud 1 and 2-Bay.
Here are some information allowing to identify these devices:
Product name | Personal Cloud | Personal Cloud 2-Bay
Code name (board/PCB) | Cumulus | Cumulus Max
Model name (case sticker) | SRN21C | SRN22C
Material desc (product spec) | STCRxxxxxxx | STCSxxxxxxx
Chipset list:
- SoC Marvell Armada 370 88F6707, CPU @1GHz
- SDRAM memory: 512MB DDR3 667MHz (16-bits bandwidth)
- SPI flash 1MB (Macronix MX25L8006E)
- 1 or 2 SATA internal ports
- 1 Ethernet Gigabit port (PHY Marvell 88E1518)
- 1 USB3 host port (PCIe controller ASM1042)
- 1 USB2 host port (SoC)
- 2 push buttons (power and reset)
- 1 SATA LED (bi-color, white and red)
Note that support for the white SATA LED is missing. A dedicated LED
driver is needed.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds DT support for the Seagate NAS 2 and 4-Bay.
Here are some information allowing to identify these devices:
Product name | Seagate NAS 2-Bay | Seagate NAS 4-Bay
Code name (board/PCB) | Dart 2-Bay | Dart 4-Bay
Model name (case sticker) | SRPD20 | SRPD40
Material desc (product spec) | STCTxxxxxxx | STCUxxxxxxx
Chipset list (common):
- SoC Marvell Armada 370 88F6707, CPU @1.2GHz
- SDRAM memory: 512MB DDR3 600MHz (16-bits bandwidth)
- NAND flash 256MB, 8-bits (Micron MT29F2G08AAB or Hinyx H27U2G8F2CTR-BC)
- 2 SATA II ports (SoC)
- 1 Ethernet Gigabit ports (PHY Marvell 88E1518)
- 2 USB3 host ports (PCIe controller ASM1042)
- GPIO fan (4 speeds)
- External I2C RTC (MCP7940NT)
- 3 push buttons (power, backup and reset)
- 2 SATA LEDs (bi-color, blue and red)
- 1 power LED (bi-color, blue and red)
Only on 4-Bay models:
- 2 extra SATA III ports (PCIe AHCI controller Marvell 88SE9170)
- 1 extra Ethernet Gigabit ports (PHY Marvell 88E1518)
- I2C GPIO expander (PCA9554A)
- 2 extra SATA LEDs (bi-color, blue and red)
Note that support for the white SATA LEDs associated with HDDs 0 and 1
is missing. A dedicated LED driver is needed.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The C.H.I.P. is a small SBC with an Allwinner R8, 8GB of NAND, 512MB of
RAM, USB host and OTG, a wifi / bluetooth combo chip, an audio/video jack
and two connectors to plug additional boards on top of it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The LinkSprite pcDuino2 board is almost identical to the older
LinkSprite pcDuino1 board according to the schematic pdf files.
So we just include the existing "sun4i-a10-pcduino.dts" file and
make the necessary adjustments.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Merge "Broadcom devicetree changes for v4.4" from Florian Fainelli:
This pull requests contains the following Broadcom SoCs Device Tree changes:
- Brian Norris documents the BCM7445 SoCs Power Management controllers and
hardware and updates the reference BCM7445 Device Tree with these nodes
- Florian Fainelli documents the BCM7xxx write-pairing feature in the top-level
BCM7xxx binding document
- Hauke Merthens enables the NAND controller for the Asus RT-AC87U and adds the
GPIO pin controlling the USB power supply on Netgear R6250
- Jon Mason adds support for the NorthStar Plus SoC by providing a top-level
binding document and the minimalist device tree skeleton for these SoCs
- Rafal Milecki adds support for the Netgear R7000 (BCM5301x SoC)
- Ray Jui provides a set of Cygnus DT changes that make the Device Tree clearer
and more correct with respect to how the hardware is designed. He also enables
the NAND controller on the bcm911360_entphn design, enables a bunch of
peripherals on the bcm958305k evaluation board, and adds a skeleton .dtsi file
for the touchscreen extansion board(s)
* tag 'arm-soc/for-4.4/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: move aliases back to .dts in Cygnus
ARM: dts: fix Cygnus nand device node
ARM: dts: enable touchscreen support on Cygnus
ARM: dts: Enable NAND support on bcm911360_entphn
ARM: dts: Enable various peripherals on bcm958305k
ARM: dts: Reorder Cygnus peripherals
ARM: dts: Move all Cygnus peripherals into axi bus
ARM: dts: Put Cygnus core components under core bus
ARM: dts: Use label for device nodes in Cygnus dts
ARM: dts: consolidate aliases for Cygnus dt files
ARM: BCM5301X: Netgear R6250 add USB GPIO
Documentation: bindings: brcmstb: Document write-pairing
ARM: dts: brcmstb: add BCM7445 system PM DT nodes
Documentation: dt: brcmstb: add system PM bindings
ARM: BCM5301X: add NAND flash chip description for Asus RT-AC87U
ARM: BCM5301X: Add DT for Netgear R7000
ARM: NSP: add minimal Northstar Plus device tree
dt-bindings: Create Documentation for NSP DT bindings
system-on-module as well as the square baseboard. On top of that
a lot of mmc-related changes to improve speeds on the Cortex-A9
socs and also setting up the supplies for rk3288 mmc-controllers
for the following mmc-tuning support. And of course the dts-part
of the rk3288 power-domains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWFta1AAoJEPOmecmc0R2BwsoH/iAhuYW/AMw9theS5e3QKYaT
AetDQHjjXPkbQpkMMxVpyyIGhBvHWHX+iTINqkVVx5MVlhvC1xmF4oJ6Yo4lbDVF
S6YgYrgI72P4inP0v3DZhJ2CpYB7bTVcPsU/ZiJOacvwKk2rgXWqE+nbBrZHpYbe
pDR9ONdOB0PsXfTsawcjb1FmK2/+xwRhHZJUSdlQRIoUZe1qIOjR2Lx25sprQ6vb
v6sBuY2T/rrWlKE0ME6HtdcA2s7HLKY1E1OdQPr15ceXR8k0yRz0dqH0ydULtZVZ
d6ZghxS+1ygir6Uw4sUXQa5QZjEeWU7M9+z6jCdKLEH/jUuaTFKFj+tko9uboa8=
=LB4D
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "Rockchip dts32 changes for 4.4" from Heiko Stuebner:
DTS changes including one new Veyron-board and the Radxa Rock2
system-on-module as well as the square baseboard. On top of that
a lot of mmc-related changes to improve speeds on the Cortex-A9
socs and also setting up the supplies for rk3288 mmc-controllers
for the following mmc-tuning support. And of course the dts-part
of the rk3288 power-domains.
* tag 'v4.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the support power-domain node on RK3288 SoCs
ARM: dts: rockchip: add rk3288-firefly iodomains
ARM: dts: rockchip: fixup firefly mmc supplies
ARM: dts: rockchip: add rk3288-popmetal iodomains
ARM: dts: rockchip: add rk3288-popmetal mmc supplies
ARM: dts: rockchip: add rk3288-popmetal board to dtb list
ARM: dts: rockchip: Add dtb for the Radxa Rock 2 Square board
ARM: dts: rockchip: support highspeed sd-cards on rk3066a boards
ARM: dts: rockchip: support highspeed sd-cards for rk3188-radxarock
ARM: dts: rockchip: Add the hdmi-ddc pinctrl settings for rk3288
ARM: dts: rockchip: Remove specific cts pullup from veyron
ARM: dts: rockchip: pull up cts lines on rk3288
ARM: dts: rockchip: add veyron-jaq board
ARM: dts: rockchip: Add support for SD/MMC on MarsBoard-RK3066
dt-bindings: add power-domain header for RK3288 SoCs
The popmetal board was not included in the list of Rockchip boards,
so was only built when explicitly called with make rk3288-popmetal.dtb
but not in a generic make dtbs, so add the missing entry.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Radxa Rock 2 Square board is a combination of the Radxa Rock 2 SoM
with the Square baseboard. Add a dtsi for the SoM which can be included
into the dts for the various baseboards (e.g. full and square) and a dts
for the square board.
Currently supported are serial console, wired networking, hdmi output,
eMMC and SD storage and USB.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
a.k.a. Haier Chromebook 11, and others
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the initial device tree for the R8A7791 SoC based Porter low cost board
(which is a slightly modified version of the Henninger board).
SCIF0 serial port support is included, so that the serial console can work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The A20-SOM-EVB is a reference design of a 2-layer board for the
A20-SOM.
It expands the features of A20-SOM by adding VGA connector, HDMI
connector, audio In/Out, LCD connector, 2 Mpix camera, gigabit
Ethernet, SATA, USB-OTG and 2 USB hosts.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There are 2 revisions of the Exynos5250 Snow Chromebook that were
shipped: Rev4 and Rev5. The only difference between these 2 revisions
is the codec, Rev4 has a max98095 codec while Rev5 has a max98090.
Mainline only supports Rev4 so this patch moves the common device
nodes to a DTSI file and adds a DTS for the Exynos5250 Snow Rev5.
The Snow Rev5 DTS is based on the DTS found in the ChromiumOS 3.8
tree.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Wits Pro A20 DKT is an A20 Development KiT with 1G RAM, 4G NAND,
sdio wifi, 1Gbit ethernet, 1024x768 lcd screen with ft5x_ts touchscreen
and a ton of IO connectors.
Note there seem to be multiple sdcard slots on the board (4 in total), but
other then mmc0 none of these are hooked up by default, there is a ton of
dip-switches which likely allow hooking some of these up, but the
documentation of the board only describes the use of a fraction of them,
so for now we only support mmc0.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
[hdegoede@redhat.com: Use pwrseq instead of a regulator for the wifi-en pin]
[hdegoede@redhat.com: Add support for OOB irq for the sdio wifi]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a generic dts file for A33 based q8 formfactor tablets,
this is intended to replace both sun8i-a33-ippo-q8h-v1.2.dts and
sun8i-a33-et-q8-v1.6.dts (these can be fully dropped after a
transition period).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The bs1078v2 is a pcb found in 10.1" tablets with an A31 soc, 1G RAM
and 8G NAND, rtl8723as usb wifi, 1 micro USB OTG port, 1 USB HOST port
This commit adds a dts for v2 of the bs1078 pcb.
Signed-off-by: Lawrence Yu <lyu@micile.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commits adds a generic dts file for q8 formfactor a13 based tablets.
The tablets ship in many variants, with the difference mainly being the
touchscreen controller / accelerometer / wifi chip used.
The wifi is USB based, and thus not listed in devicetree.
The touchscreen controller / accelerometer may turn out to be a problem
once we add support for those. We can either do something with devicetree
overlays, or add sun5i-a13-<touchscreen>-<accelerometer>.dts files. The
latter is what the android mod community is doing with firmware images.
This dts was tested with an a13 q8 tablet with a pcb labelled: "94V-0",
silead gsl1680 touchscreen controller and a mc32x0 accelerometer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Wobo i5 top set box is a somewhat curious A10s based top set box,
it uses an AXP209 rather then the AXP152 usually used in combination
with the A10s. It has an ethernet phy connected to PORTD rather then
PORTA, and its built-in usb wifi is connected via the otg controller.
This commit adds a dts file adding support for this top set box.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The iNet-tek iNet-1 PCB is a PCB found in various generic 10.1" 1024x600
A10 based tablets such as the Point of View Protab2 XXL and the
Cherry M1007.
This patch has been tested on both rev2 and rev5 of this board / these
tablets.
It comes with a rtl8188cus usb wifi connected to ehci1, focal ft5406ee8
touchscreen connected to i2c2 addr 0x38, bosch bma 250 accelerometer
connected to i2c1 addr 0x18 and the usual connectors: headphone,
mini hdmi, power-barrel, mini-usb and a micro-sd slot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The inet9f-rev03 pcb is specially designed for gaming tablets, such as
the qware tb-g100 tablet.
These 7" tablets feature a dpad, firebuttons and 2 joysticks on the sides
of the screen.
Besides this they have the usual connectors: power-barrel, mini usb,
mini hdmi, headphone and micro-sd slot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The inet98v_rev2 is a pcb used in generic A13 based tablets. It features
volume buttons, a power barrel, micro-usb otg, headphone connector and
a power button.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Auxtek-T003 HDMI stick is an A10s based HDMI stick with USB wifi,
and composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Jens Kuske