http://bugzilla.kernel.org/show_bug.cgi?id=12542 reports that with the
quirk not applied on resume, msi stops working after resuming and mcp78s
ahci fails due to IRQ mis-delivery. Apply it on resume too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: Tj <linux@tjworld.net>
Reported-by: Nicolas Derive <kalon33@ubuntu.com>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
One more form factor for Compaq Evo D510, which needs the same quirk
as the other form factors. Apparently there's no hardware monitoring
chip on that one, but SPD EEPROMs, so it's still worth unhiding the
SMBus.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Nuzhna Pomoshch <nuzhna_pomoshch@yahoo.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The ALi loses some state if it goes into D3. Unfortunately even with the
chipset documents I can't figure out how to restore some bits of it.
The VIA one saves/restores apparently fine but the ACPI _GTM methods break
on some platforms if we do this and this causes cable misdetections.
These are both effectively regressions as historically nothing matched the
devices and then decided not to bind to them. Nowdays something is binding
to all sorts of devices and a result they get dumped into D3.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (74 commits)
PCI: make msi_free_irqs() to use msix_mask_irq() instead of open coded write
PCI: Fix the NIU MSI-X problem in a better way
PCI ASPM: remove get_root_port_link
PCI ASPM: cleanup pcie_aspm_sanity_check
PCI ASPM: remove has_switch field
PCI ASPM: cleanup calc_Lx_latency
PCI ASPM: cleanup pcie_aspm_get_cap_device
PCI ASPM: cleanup clkpm checks
PCI ASPM: cleanup __pcie_aspm_check_state_one
PCI ASPM: cleanup initialization
PCI ASPM: cleanup change input argument of aspm functions
PCI ASPM: cleanup misc in struct pcie_link_state
PCI ASPM: cleanup clkpm state in struct pcie_link_state
PCI ASPM: cleanup latency field in struct pcie_link_state
PCI ASPM: cleanup aspm state field in struct pcie_link_state
PCI ASPM: fix typo in struct pcie_link_state
PCI: drivers/pci/slot.c should depend on CONFIG_SYSFS
PCI: remove redundant __msi_set_enable()
PCI PM: consistently use type bool for wake enable variable
x86/ACPI: Correct maximum allowed _CRS returned resources and warn if exceeded
...
I found no references to SMBus in ACPI DSDT disassembly on my laptop
so this should be safe.
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some BIOSes hide 'overflow' device (dev #6) for i82875P/PE chipsets.
The same happens for i82865P/PE. Add a quirk to enable this device.
This allows i82875 EDAC driver to bind to chipset's dev #6 and not
dev #0 as the latter is used by AGP driver.
On my laptop (i82865P based) ACPI code is disabling this device
again in \_SB.PCI0._CRS method (called at least at PNP init time).
This can be easily worked around by patching DSDT.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>
Acked-by: Doug Thompson <norsk5@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Addition of one unknown subsystem identifier to the quirks handler for
chipset i82855GM_HB on notebook Asus A6L. This exposes the otherwise
hidden SMBus controller within the south bridge ICH4-M.
Signed-off-by: Mats Erik Andersson <mats.andersson@gisladisker.se>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The current quirk doesn't include all 82576 device IDs. This update
resolves that.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch, Broadcom BCM5906 Ethernet controllers set up via MSI
cause the machine to hang. Tejun agreed that the best is to blacklist
the whole chipset and after adding it, seeing the other VIA quirks
disabling MSI, this very much looks like the right way.
Cc: <stable@kernel.org>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch fixes breakage of of enable_cnt in quirk_resource_alignment.
Currently, quirk_resource_alignment calls pci_disable_device.
pci_disable_device decrements enable_cnt, so that enable_cnt becomes -1.
The patch disables memory decoding, writing command register directly.
So enable_cnt is not broken.
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If BIOS doesn't allocate resources for the SR-IOV BARs, zero the Flash
BAR and program the SR-IOV BARs to use the old Flash Memory Space.
Please refer to Intel 82576 Gigabit Ethernet Controller Datasheet
section 7.9.2.14.2 for details.
http://download.intel.com/design/network/datashts/82576_Datasheet.pdf
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Impact: fix bug
This patch reworks the nv_msi_ht_cap_quirk() and will only try to avoid
to enable ht_msi on device following that root dev, and don't touch that
root dev, but only do that trick with end_device on the chain.
Reported-by: Prakash Punnoor <prakash@punnoor.de>
Tested-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Impact: fix bug
Prakash reported that his c51-mcp51 system ondie sound card doesn't work
MSI but if he hack out the HT-MSI on mcp51, the MSI will work well with
sound card.
This patch reworks nv_msi_ht_cap_quirk() and will only avoid enabling
ht_msi on devices following that root device.
Reported-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
On the Compaq Evo D510 SFF/CMT, a PCI quirk activated the SMBus device
based on detection of the on-board VGA controller, but the on-board
VGA is disabled if an AGP card is inserted, so look for one of the USB
controllers instead.
Signed-off-by: David O'Shea <dcoshea@hotmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch allows memory resources to be assigned with a specified
alignment at boot-time or run-time. The patch is useful when we use PCI
pass-through, because page-aligned memory resources are required to
securely share PCI resources with guest drivers.
If you want to assign the resource at boot time, please set
"pci=resource_alignment=" boot parameter.
This is format of "pci=resource_alignment=" boot parameter:
[<order of align>@][<domain>:]<bus>:<slot>.<func>[; ...]
Specifies alignment and device to reassign
aligned memory resources.
If <order of align> is not specified, PAGE_SIZE is
used as alignment.
PCI-PCI bridge can be specified, if resource
windows need to be expanded.
This is example:
pci=resource_alignment=20@07:00.0;18@0f:00.0;00:1d.7
If you want to assign the resource at run-time, please set
"/sys/bus/pci/resource_alignment" file, and hot-remove the device and
hot-add the device. For this purpose, fakephp or PCI hotplug interfaces
can be used.
The format of "/sys/bus/pci/resource_alignment" file is the same with
boot parameter. You can use "," instead of ";".
For example:
# cd /sys/bus/pci
# echo -n 20@12:00.0 > resource_alignment
# echo 1 > devices/0000:12:00.0/remove
# echo 1 > rescan
Reviewed-by: Alex Chiang <achiang@hp.com>
Reviewed-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Yuji Shimada <shimada-yxb@necst.nec.co.jp>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Let it stay as serial, since it doesn't have subdevice in the form of 0x00PS.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Prakash's system needs MSI disabled on some bridges, but not all.
This seems to be the minimal fix for 2.6.29, but should be replaced
during 2.6.30.
Signed-off-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
This patch is intended to disable L0s ASPM link state for 82598 (ixgbe)
parts due to the fact that it is possible to corrupt TX data when coming
back out of L0s on some systems. The workaround had been added for 82575
(igb) previously, but did not use the ASPM api. This quirk uses the ASPM
api to prevent the ASPM subsystem from re-enabling the L0s state.
Instead of adding the fix in igb to the ixgbe driver as well it was
decided to move it into a pci quirk. It is necessary to move the fix out
of the driver and into a pci quirk in order to prevent the issue from
occuring prior to driver load to handle the possibility of the device being
passed to a VM via direct assignment.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Turns out that the new AMD 813x devices do not need the
quirk_disable_amd_813x_boot_interrupt quirk to be run on them. If it
is, no interrupts are seen on the PCI-X adapter.
From: Stefan Assmann <sassmann@novell.com>
Reported-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Tested-by: Jamie Wellnitz <Jamie.Wellnitz@emulex.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
Prakash reported that his c51-mcp51 ondie sound card doesn't work with
MSI. But if he hacks out the HT-MSI quirk, MSI works fine.
So this patch reworks the nv_msi_ht_cap_quirk(). It will now only
enable ht_msi on own its root device, avoiding enabling it on devices
following that root dev.
Reported-by: Prakash Punnoor <prakash@punnoor.de>
Tested-by: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@hobbes.lan>
David reported that LSI SAS doesn't work with MSI. It turns out that
his BIOS doesn't enable it, but the HT MSI 8132 does support HT MSI.
Add quirk to enable it
Cc: stable@kernel.org
Reported-by: David Lang <david@lang.hm>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
All the other quirks are dev_info() not dev_err(), this one isn't special.
This makes 'quiet' boot in qemu really quiet.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This adds more LPC controller IO range decode quirks for the Intel ICH
family of chipsets. They differ a bit between the older ICH6 chipset and
the more modern layout of the ICH7-ICH10 chipsets.
This patch just prints out the IO decode information found by the quirks,
but eventually we may want to add them to the resource tree, in order to
know to avoid allocating things over them.
That's especially true if it turns out that any firmware ends up putting
the magic motherboard resources in an address range that we use for
dynamic allocations (ie above PCIBIOS_MIN_IO, which is 0x1000 on x86).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Greg KH <greg@kroah.com>
Cc: Frans Pop <elendil@planet.nl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
VPD quirks need to be called after the VPD capability is initialized.
Since VPD initialization now runs after pci_fixup_header (due to the
capabilities consolidation), VPD quirks should be done at
pci_fixup_final stage correspondingly.
Tested-by: Eric Dumazet <dada1@cosmosbay.com>
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
On Thu, Oct 23, 2008 at 04:09:52PM -0700, Alexander Beregalov wrote:
> arch/x86/kernel/built-in.o: In function `iommu_setup':
> pci-dma.c:(.init.text+0x36ad): undefined reference to `forbid_dac'
> pci-dma.c:(.init.text+0x36cc): undefined reference to `forbid_dac'
> pci-dma.c:(.init.text+0x3711): undefined reference to `forbid_dac
This patch partially reverts a patch to add IOMMU support to ia64. The
forbid_dac variable was incorrectly moved to quirks.c, which isn't built
when PCI is disabled.
Tested-by: "Alexander Beregalov" <a.beregalov@gmail.com>
Acked-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use %pF instead of print_fn_descriptor_symbol() in quirks.c to get the name of
the hook we're calling.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds the CONFIG_PCI_QUIRKS option which allows to remove all
the PCI quirks, which are not necessarily used on embedded systems when
PCI is working properly. As this is a size-reduction option, it depends
on CONFIG_EMBEDDED. It allows to save almost 12 kilobytes of kernel
code:
text data bss dec hex filename
1287806 123596 212992 1624394 18c94a vmlinux.old
1275854 123596 212992 1612442 189a9a vmlinux
-11952 0 0 -11952 -2EB0 +/-
This patch has originally been written by Zwane Mwaikambo
<zwane@arm.linux.org.uk> and is part of the Linux Tiny project.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The current Intel IOMMU code assumes that both host page size and Intel
IOMMU page size are 4KiB. The first patch supports variable page size.
This provides support for IA64 which has multiple page sizes.
This patch also adds some other code hooks for IA64 platform including
DMAR_OPERATION_TIMEOUT definition.
[dwmw2: some cleanup]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
I dunno how this missed Bjorn and his quest to use %pF in commit
c80cfb0406 ("vsprintf: use new vsprintf
symbolic function pointer format"), but it did.
So use %pF in the two remaining places that still tried to print out
function pointers by hand.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Libata has some hacks to deal with certain controllers going silly in D3
state. The right way to handle this is to keep a PCI device flag for
such devices. That can then be generalised for no ATA devices with power
problems.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is against linux-2.6-tip, branch pci-ioapic-boot-irq-quirks.
From: Stefan Assmann <sassmann@suse.de>
Subject: Introduce config option for pci reroute quirks
The config option X86_REROUTE_FOR_BROKEN_BOOT_IRQS is introduced to
enable (or disable) the redirection of the interrupt handler to the boot
interrupt line by default. Depending on the existence of interrupt
masking / threaded interrupt handling in the kernel (vanilla, rt, ...)
and the maturity of the rerouting patch, users can enable or disable the
redirection by default.
This means that the reroute quirk can be applied to any kernel without
changing it.
Interrupt sharing could be increased if this option is enabled. However this
option is vital for threaded interrupt handling, as done by the RT kernel.
It should simplify the consolidation with the RT kernel.
The option can be overridden by either pci=ioapicreroute or
pci=noioapicreroute.
Signed-off-by: Stefan Assmann <sassmann@suse.de>
Signed-off-by: Olaf Dabrunz <od@suse.de>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Jon Masters <jonathan@jonmasters.org>
Cc: Ihno Krumreich <ihno@suse.de>
Cc: Sven Dietrich <sdietrich@suse.de>
Cc: Daniel Gollub <dgollub@suse.de>
Cc: Felix Foerster <ffoerster@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
It is not necessary to call boot IRQ quirks before the BARs of the bridges are
probed. The normal case is to use DECLARE_PCI_FIXUP_FINAL, so we use this
instead now.
After a resume, we need to call the quirks again.
Signed-off-by: Olaf Dabrunz <od@suse.de>
Signed-off-by: Stefan Assmann <sassmann@suse.de>
Cc: Jon Masters <jonathan@jonmasters.org>
Cc: Olaf Dabrunz <od@suse.de>
Cc: Stefan Assmann <sassmann@suse.de>
Cc: Ihno Krumreich <ihno@suse.de>
Cc: Sven Dietrich <sdietrich@suse.de>
Cc: Daniel Gollub <dgollub@suse.de>
Cc: Felix Foerster <ffoerster@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add quirks for several AMD/ATI chipsets to prevent generation of legacy boot
interrupts.
Integrates a separate older quirk to make IO-APIC mode work on
AMD 8131 rev. A0 and B0, which was due to an AMD erratum.
Signed-off-by: Olaf Dabrunz <od@suse.de>
Signed-off-by: Stefan Assmann <sassmann@suse.de>
Cc: Jon Masters <jonathan@jonmasters.org>
Cc: Olaf Dabrunz <od@suse.de>
Cc: Stefan Assmann <sassmann@suse.de>
Cc: Ihno Krumreich <ihno@suse.de>
Cc: Sven Dietrich <sdietrich@suse.de>
Cc: Daniel Gollub <dgollub@suse.de>
Cc: Felix Foerster <ffoerster@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Olaf Dabrunz <od@suse.de>
Signed-off-by: Stefan Assmann <sassmann@suse.de>
Cc: Jon Masters <jonathan@jonmasters.org>
Cc: Olaf Dabrunz <od@suse.de>
Cc: Stefan Assmann <sassmann@suse.de>
Cc: Ihno Krumreich <ihno@suse.de>
Cc: Sven Dietrich <sdietrich@suse.de>
Cc: Daniel Gollub <dgollub@suse.de>
Cc: Felix Foerster <ffoerster@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch just fixes the compiler warning:
drivers/pci/quirks.c: In function ‘quirk_reroute_to_boot_interrupts_intel’:
drivers/pci/quirks.c:1375: warning: unused variable ‘i’
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Cc: sassmann@suse.de
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some chipsets (e.g. intel 6700PXH) generate a legacy INTx when the
IRQ entry in the chipset's IO-APIC is masked (as, e.g. the RT kernel
does during interrupt handling). On chipsets where this INTx generation
cannot be disabled, we reroute the valid interrupts to their legacy
equivalent to get rid of spurious interrupts that might otherwise bring
down (vital) interrupt lines through spurious interrupt detection in
note_interrupt().
This patch benefited from discussions with Alexander Graf, Torsten Duwe,
Ihno Krumreich, Daniel Gollub, Hannes Reinecke. The conclusions we drew
and the patch itself are the authors' responsibility alone.
Signed-off-by: Stefan Assmann <sassmann@suse.de>
Signed-off-by: Olaf Dabrunz <od@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a quirk to disable legacy boot interrupt generation on intel devices
that support disabling it.
This patch benefited from discussions with Alexander Graf, Torsten Duwe,
Ihno Krumreich, Daniel Gollub, Hannes Reinecke. The conclusions we drew
and the patch itself are the authors' responsibility alone.
Signed-off-by: Stefan Assmann <sassmann@suse.de>
Signed-off-by: Olaf Dabrunz <od@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It seems VT3336 can't do msi either as with its bro 3351. Disable it.
Reported in the following SUSE bug.
https://bugzilla.novell.com/show_bug.cgi?id=300001
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the
VPD end tag will hang the device. This problem was initially
observed when a vpd entry was created in sysfs
('/sys/bus/pci/devices/<id>/vpd'). A read to this sysfs entry
will dump 32k of data. Reading a full 32k will cause an access
beyond the VPD end tag causing the device to hang. Once the device
is hung, the bnx2 driver will not be able to reset the device.
We believe that it is legal to read beyond the end tag and
therefore the solution is to limit the read/write length.
A majority of this patch is from Matthew Wilcox who gave code for
reworking the PCI vpd size information. A PCI quirk added for the
Broadcom NIC's to limit the read/write's.
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch unhides the SMBus on Compaq Deskpro EN
SFF P667 with the Intel 815E chipset. Unhiding it reveals
a THMC51 hardware monitoring chip.
Jean Delvare has checked that this machine has no ACPI
magic touching the SMBus nor the hardware monitoring chip,
so this should be safe.
The patch was tested on Fedora Core 9 with 2.6.25.4 kernel.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Tested-by: Rafał Haładuda <rh1985@wp.pl>
CC: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
One more machine with a hidden Intel SMBus. Unhiding it reveals a SMSC
EMC6D100 hardware monitoring chip. I have checked that this machine
has no ACPI magic touching the SMBus nor the hardware monitoring chip,
so this should be safe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some quirks should be called with interrupt disabled, we can't directly
call them in .resume_early. Also the patch introduces
pci_fixup_resume_early and pci_fixup_suspend, which matches current
device core callbacks (.suspend/.resume_early).
TBD: Somebody knows why we need quirk resume should double check if a
quirk should be called in resume or resume_early. I changed some per my
understanding, but can't make sure I fixed all.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Everybody wants to pass it a function pointer, and in fact, that is what
you _must_ pass it for it to make sense (since it knows that ia64 and
ppc64 use descriptors for function pointers and fetches the actual
address from there).
So don't make the argument be a 'unsigned long' and force everybody to
add a cast.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This applies the NVidia MSI enabled flag for HT capable devices quirk
to ALi bridges as well.
As described in more detail in http://bugzilla.kernel.org/show_bug.cgi?id=10667
this is required for my board which is using an nForce 3 250Gb chipset with an
ALi M1695 northbridge.
It fixes a regression introduced in 2.6.24 that made the internal NIC of the
board unusable (MSI initialisation of the NIC but disabled MSI on the
northbridge devices.
Signed-off-by: Björn Krombholz <fox.box@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This follows up 53a9bf4267. Some newer
CX700 BIOSes from our vendor have PCI Bus Parking disabled but PCI
Master read caching enabled. This creates problems such as system
freezing when both the network controller and the USB controller are
active and one of them is pretty busy (e.g. heavy network traffic).
This patch separates the checks and both the bus parking and the read
caching are disabled independently if either is enabled by the BIOS.
Signed-off-by: Tim Yamin <tim.yamin@zonbu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
print_fn_descriptor_symbol() prints the address if we don't have a symbol,
so no need to print both.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 3c0a654e39 and
fixes kernel bug #10245:
http://bugzilla.kernel.org/show_bug.cgi?id=10245
The HP Compaq nc6120 has the same PCI sub-device ID as the nx6110, and the
SMBus is used by ACPI for thermal management on the nc6120, so Linux should
not attach a native driver to it. This means that this quirk is unsafe and
has to be removed.
I also added a comment to help developers realize that adding new IDs to this
SMBus unhiding quirk table should be done only with great care, and in
particular only after checking that ACPI is not making use of the SMBus.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Tomasz Koprowski <tomek@koprowski.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to HT spec, to get message interrupt from devices mapped to HT
interrupt message, the 'En' bit of MSI Mapping capability need to be set.
The patch do this setting in quirks code for the devices on HT-based nvidia
platform.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Andy Currid <acurrid@nvidia.com>
Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI: modify SATA IDE mode quirk
When initialize and resume, SB600/700/800 need to set SATA mode
correctly.
Signed-off-by: Crane Cai <crane.cai@amd.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SB700 SATA MSI bug will be fixed in SB700 revision A21 at hardware
level, but the SB700 revision older than A21 will also be found in the
market. This patch modify the original quirk commit
bc38b411fe instead of withdrawing it.
The patch also removes quirk to 0x4395 because 0x4395 is SB800 device
ID.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert quirk printks to dev_printk().
I made the MSI disable messages a little more consistent:
- always use "disabled", not "deactivated"
- specify "device MSI disabled" or "subordinate MSI disabled" when
disabling MSI for only a specific device or subordinate bus
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of printing this:
PCI: Calling quirk c023b250 for 0000:00:00.0
we can print this:
pci 0000:00:00.0: calling quirk 0xc023b270: quirk_cardbus_legacy+0x0/0x30()
The address is superfluous because sprint_symbol() includes the
address if the symbol lookup fails, but this is the same style used
in do_initcalls() and pnp_fixup_device().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check that the e100 is in the D0 power state. If it's not, it won't
respond to MMIO accesses and we end up with master-abort machine
checks on some platforms.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unhide the SMBus on the HP xw4100. This gives access to a hardware
monitoring chip (ADT7463) and to the memory module SPD EEPROMs. I
checked that ACPI wasn't accessing the SMBus, so it should be safe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove lots of space-before-) instances. Perhaps these were a workaround for
problems in some long-dead cpp version.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI Bus Parking and PCI Master read caching on the VIA CX700 is buggy and
can lead to problems such as USB2.0 packet loss if a VT6212L controller
is on the PCI bus. It's disabled by default, but some BIOSes turn these
features on and this patch reverts the configuration to the safe defaults.
Signed-off-by: Tim Yamin <tim.yamin@zonbu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't read the revision ID unnecessary since the PCI subsystem
fills this field in already.
Updated to fix a thinko bug in a previously sent patch.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It is important that these resources be reserved
to avoid conflicts with well known ACPI registers.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Now that we have dealt with the real issue, in that some ATI SATA and
USB controllers needed the INTX_DISABLE quirk, we can remove these AMD
chipset global MSI disabling quirks.
This reverts three changesets:
4be8f90643 (PCI: disable MSI on RS690)
aea6a433f5 (PCI: disable MSI on RD580)
f122392f67 (PCI: disable MSI on RX790)
This is based upon testing and feedback from
Shane Huang <Shane.Huang@amd.com>.
Cc: Shane Huang <Shane.Huang@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A reasonably common problem with some devices is that they will
disable MSI generation when the INTX_DISABLE bit is set in the
PCI_COMMAND register.
Quirk this explicitly, guarding the pci_intx() calls in msi.c with
this quirk indication.
The first entries for this quirk are for 5714 and 5780 Tigon3 chips,
and thus we can remove the workaround code from the tg3.c driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the fix for the following problem:
https://bugzilla.redhat.com/show_bug.cgi?id=227657
The bnx2 device 5706 complains about MSI not working behind a
ServerWorks HT1000 PCIX bridge. An earlier commit to fix the problem:
e3008dedff:
"PCI: disable MSI by default on systems with Serverworks HT1000 chips"
was not entirely correct, and has been reverted.
MSI does not work on the PCIX bus because the BIOS did not set the
HT_MSI_FLAGS_ENABLE bit in the HyperTransport MSI capability on the
bridge. We use the existing quirk_msi_ht_cap() to detect the problem
and disable MSI in all buses behind it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: Anantha Subramanyam <ananth@broadcom.com>
Cc: Naren Sankar <nsankar@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit e3008dedff.
The real bug was an INTX issue in the tg3 ethernet chip, and
cured by commit c129d962a66c76964954a98b38586ada82cf9381
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Set bits 0, 4, 5 and 7 of PCI configuration register 0x40 in the
quirk. This has the following effects and is recommended by the
vendor.
* Force enable of IDE channels (used to be left alone as BIOS
configured)
* Change initial phase behavior of PIO cycle such that the host pulls
down the bus instead of tristating it. Vendor recommends this
setting.
The above settings are better for the current generation of
controllers and needed for the upcoming next generation.
Tested on JMB363.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ethan Hsiao <ethanhsiao@jmicron.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On the "MSI K8T Neo2-FIR" board the BIOS disables the onboard
soundcard, if a second PCI soundcard is present.
This patch sets the korrect register bit to enable the onboard sound.
Removed old code in /drivers/pci/quirks.c that only checks for the
PCI-ID and fires on any Board with VIA 8237.
New code in /arch/i386/pci/fixup.c checks the DMI-tables and only runs
on the specific board.
Signed-off-by: Johannes Goecke <goecke@upb.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Linas reported me that some machines were crashing at boot in
quirk_e100_interrupt. It appears that this quirk is doing an ioremap
directly on a PCI BAR value, which isn't legal and will cause all sorts
of bad things to happen on architectures where PCI BARs don't directly
match processor bus addresses.
This fixes it by using the proper PCI resources instead which is possible
since the quirk has been moved by a previous commit to happen late enough
for that.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PCI quirk to unhide SMBus on Compaq Deskpro EP 401963-001 (PCA# 010174) motherboard.
Signed-off-by: Greg White <gw.kernel@tnode.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The k8t_sound_hostbridge PCI quick fires on my motherboard (Jetway
K8M8MS) while it shouldn't: the on-board sound chip is not disabled
and is working just fine. Looking at the code, I see that we are
running the quirk for two distinct register values (0x88 and 0xc8)
and then clear bit 6 (0x40). However value 0x88 already has bit 6
cleared so this is a no-op. This is what happens on my board. Thus I
believe that the quirk should only be run for register value 0xc8.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
RS690 can't do MSI like its predecessors. Disable MSI on RS690.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Henry Su <henry.su@amd.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
quirk_e100_interrupts() is called after PCI controller is initialized
and before PCI bus enumeration is performed. On some powerpc platforms
which modify PCI controller configuration and set different MEM and IO
windows than those set by firmware quirk_e100_interrupt() is causing
kernel panic as it tries to read from device BAR0 offets which at this
time points to a invalid PCI window (set by firmware).
This patch delays the quirk_100_interrupt() to pci_fixup_final phase,
which happens after bus enumeration and before PCI enable and
device driver initialization.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch introduces an interface to read and write PCI-X / PCI-Express
maximum read byte count values from PCI config space. There is a second
function that returns the maximum _designed_ read byte count, which marks the
maximum value for a device, since some drivers try to set MMRBC to the
highest allowed value and rely on such a function.
Based on patch set by Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Peter Oruba <peter.oruba@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Via VT3351 APIC does not play well with MSI and unleashes a flood
of APIC errors when MSI is used to deliver interrupts. The problem
was recently exposed when the atl1 network device driver, which enables
MSI by default, stimulated APIC errors on an Asus M2V mainboard, which
employs the Via VT3351.
See http://bugzilla.kernel.org/show_bug.cgi?id=8472 for additional
details on this bug.
Signed-off-by: Jay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've been seeing lots of messages like these:
eth0: No interrupt was generated using MSI, switching to INTx mode. Please
report this failure to the PCI maintainer and include system chipset
information.
On several systems that use the following Severworks HT1000 (also sometimes
labeled as a Broadcom chipset as well) bridge chips. It doesn't appear MSI
works well (if at all) on these systems.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit c0affe9db4 doesn't work because
the host controller is being quirked not a PCI bridge. This patch
reverts the commit, rename quirk_svw_msi() to quirk_disable_all_msi()
and use it instead.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Matias Alejandro Torres <torresmat@gmail.com>
Cc: Greg K-H <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Besides those modes in ATI SB600 SATA controller, ATI SB700 supports one
more mode:the combined mode.
The combined mode is a Legacy IDE mode used for compatibility with some old
OS without AHCI driver, but now it is not necessary for Linux since the
kernel has supported AHCI.
Signed-off-by: Luugi Marsan <luugi.marsan@amd.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Both old-IDE and libata should be able handle all controllers and
devices found using normal resource reservation methods.
This eliminates the awful, low-performing split-driver configuration
where old-IDE drove the PATA portion of a PCI device, in PIO-only mode,
and libata drove the SATA portion of the /same/ PCI device, in DMA mode.
Typically vendors would ship SATA hard drive / PATA optical
configuration, which would lend itself to slow (PIO-only) CD-ROM
performance.
For Intel users running in combined mode, it is now wholly dependent on
your driver choice (potentially link order, if you compile both drivers
in) whether old-IDE or libata will drive your hardware.
In either case, you will get full performance from both SATA and PATA
ports now, without having to pass a kernel command line parameter.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was found that the Toshiba laptops with hidden Intel SMBus have SMM
code handling the thermal management which accesses the SMBus. Thus it
is not safe to unhide it and let Linux access it. We have to leave the
SMBus hidden. SMM is a pain, really.
This fixes bugs #6315 and #6395, for good this time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In some cases when we are not using msi we need a way to ensure that the
hardware does not have an msi capability enabled. Currently the code has been
calling disable_msi_mode to try and achieve that. However disable_msi_mode
has several other side effects and is only available when msi support is
compiled in so it isn't really appropriate.
Instead this patch implements pci_msi_off which disables all msi and msix
capabilities unconditionally with no additional side effects.
pci_disable_device was redundantly clearing the bus master enable flag and
clearing the msi enable bit. A device that is not allowed to perform bus
mastering operations cannot generate intx or msi interrupt messages as those
are essentially a special case of dma, and require bus mastering. So the call
in pci_disable_device to disable msi capabilities was redundant.
quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
