Since 'num-slots' had already deprecated, remove the property in
device-tree file.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Removale of skeleton.dtsi allows us also to fix the following
warning from the dts compiler:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
by adding proper unit addresses to the memory nodes.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Remove skeleton.dtsi from the common ARM Cortex-M dtsi. This will allow
us to remove skeleton.dtsi on a per platform basis and get rid of the
unit address warning on the memory nodes without getting duplicate memory
nodes.
See 3ebee5a2e1 ("arm64: dts: kill skeleton.dtsi") for additional
reasons not to use the skeleton.dtsi.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Configure the DWMAC FIFO sizes, burst length and threshold DMA mode on
LPC18xx/43xx SoCs. These parameters are needed for correct operation of
the Ethernet MAC. The DWMAC on LPC18xx/43xx does not support RSF DMA
mode and therefore must use threshold mode.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
DT nodes without reg properties should not have a unit address. This
fixes the following warnings from dtc.
Warning (unit_address_vs_reg): Node /soc/syscon@40043000/phy@004 has a
unit name, but no reg property
Warning (unit_address_vs_reg): Node /soc/syscon@40043000/dma-mux@11c has
a unit name, but no reg property
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add node for the NXP LPC18xx EEPROM memory which can be found in
NXP LPC185x/3x and LPC435x/3x/2x/1x devices.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Most of the peripherals on LPC18xx/43xx devices have their reset
lines hooked up to internal reset controller (RGU). Add reset
entries to the device nodes so a driver can use the reset line.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
NXP LPC SoCs family, which includes LPC18xx/LPC43xx, provides a State
Configurable Timer (SCT) which can be configured as a Pulse Width
Modulator.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add node for the watchdog timer found on LPC18xx/LPC43xx.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add dmas entries to the four UART peripherals on LPC18xx/43xx devices
so that DMA can be used to transfer data.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add dmas entries to the two SSP peripherals on LPC18xx/43xx devices
so that DMA can be used to transfer data.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add node for the DMA multiplexer placed in front of the PL080 DMA
controller on lpc18xx/43xx devices.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add the NXP LPC1773 SPIFI (SPI Flash Interface) flash controller
node to the dtsi for all lpc18xx/43xx devices.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add the NXP LPC1850 RGU (Reset Generation Unit) reset controller
node to the dtsi for all lpc18xx/43xx devices.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
All devices in the LPC18xx/43xx familiy contain a ARM PL172
MultiPort Memory Controller (MPMC).
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
NXP LPC185x and LPC435x/70 devices contain a ARM PL111 lcd controller.
Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the USB OTG phy under the CREG syscon node and attach it to
the USB0 EHCI controller.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The CREG block contains a collection of miscellaneous
configuration register like Ethernet phy mode, low
power clocks and DMA multiplexer. These registers
needs to be accessed from other drivers and syscon
provides this capability.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Add gpio and mapping between pinctrl/gpio namespace with
gpio-ranges property.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add CGU and CCU clock-controller nodes for lpc18xx together with
the fixed input clocks. Also remove the temporary fixed-factor
pll1 clock from both lpc18xx and lpc4350-hitex-eval DTS now that
proper clock drivers are inplace.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Michael Turquette <mturquette@baylibre.com>
NXP LPC18xx/43xx SoCs are very similar devices and should be able to
share a common base (lpc18xx.dtsi). Diffences between the devices are
put in a dtsi which is specific to that device.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Jaehoon Chung