from include/asm-powerpc. This is the result of a
mkdir arch/powerpc/include/asm
git mv include/asm-powerpc/* arch/powerpc/include/asm
Followed by a few documentation/comment fixups and a couple of places
where <asm-powepc/...> was being used explicitly. Of the latter only
one was outside the arch code and it is a driver only built for powerpc.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds code to deal with conversion of
logical cpu to cbe nodes. It removes code that
assummed there were two logical CPUs per CBE.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This is a clean up patch that includes the following changes:
-Some comments were added to clarify the code based on feedback
from the community.
-The write_pm_cntrl() and set_count_mode() were passed a
structure element from a global variable. The argument was
removed so the functions now just operate on the global directly.
-The set_pm_event() function call in the cell_virtual_cntr()
routine was moved to a for-loop before the for_each_cpu loop
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Add PPU event-based and cycle-based profiling support to Oprofile for Cell.
Oprofile is expected to collect data on all CPUs simultaneously.
However, there is one set of performance counters per node. There are
two hardware threads or virtual CPUs on each node. Hence, OProfile must
multiplex in time the performance counter collection on the two virtual
CPUs.
The multiplexing of the performance counters is done by a virtual
counter routine. Initially, the counters are configured to collect data
on the even CPUs in the system, one CPU per node. In order to capture
the PC for the virtual CPU when the performance counter interrupt occurs
(the specified number of events between samples has occurred), the even
processors are configured to handle the performance counter interrupts
for their node. The virtual counter routine is called via a kernel
timer after the virtual sample time. The routine stops the counters,
saves the current counts, loads the last counts for the other virtual
CPU on the node, sets interrupts to be handled by the other virtual CPU
and restarts the counters, the virtual timer routine is scheduled to run
again. The virtual sample time is kept relatively small to make sure
sampling occurs on both CPUs on the node with a relatively small
granularity. Whenever the counters overflow, the performance counter
interrupt is called to collect the PC for the CPU where data is being
collected.
The oprofile driver relies on a firmware RTAS call to setup the debug bus
to route the desired signals to the performance counter hardware to be
counted. The RTAS call must set the routing registers appropriately in
each of the islands to pass the signals down the debug bus as well as
routing the signals from a particular island onto the bus. There is a
second firmware RTAS call to reset the debug bus to the non pass thru
state when the counters are not in use.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The following routines are added to arch/powerpc/platforms/cell/pmu.c:
cbe_clear_pm_interrupts()
cbe_enable_pm_interrupts()
cbe_disable_pm_interrupts()
cbe_query_pm_interrupts()
cbe_pm_irq()
cbe_init_pm_irq()
This also adds a routine in arch/powerpc/platforms/cell/interrupt.c and
some macros in cbe_regs.h to manipulate the IIC_IR register:
iic_set_interrupt_routing()
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move some PMU-related macros and function prototypes from cbe_regs.h
and pmu.h in arch/powerpc/platforms/cell/ to a new header at
include/asm-powerpc/cell-pmu.h
This is cleaner to use from the oprofile code, since that sits in
arch/powerpc/oprofile, not in the cell platform directory.
Signed-off-by: Kevin Corry <kevcorry@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>