The rockchip io-domain driver currently only depends on ARCH_ROCKCHIP
itself. This makes it possible to select the power-domain driver, but
not the POWER_AVS class and results in the iodomain-driver not getting
build in this case.
So add the additional dependency, which also results in the driver
config option now being placed nicely into the AVS submenu.
Fixes: 662a958638 ("PM / AVS: rockchip-io: add driver handling Rockchip io domains")
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
IO domain voltages on some Rockchip SoCs are variable but need to be
kept in sync between the regulators and the SoC using a special
register.
A specific example using rk3288:
- If the regulator hooked up to a pin like SDMMC0_VDD is 3.3V then
bit 7 of GRF_IO_VSEL needs to be 0. If the regulator hooked up to
that same pin is 1.8V then bit 7 of GRF_IO_VSEL needs to be 1.
Said another way, this driver simply handles keeping bits in the SoC's
general register file (GRF) in sync with the actual value of a voltage
hooked up to the pins.
Note that this driver specifically doesn't include:
- any logic for deciding what voltage we should set regulators to
- any logic for deciding whether regulators (or internal SoC blocks)
should have power or not have power
If there were some other software that had the smarts of making
decisions about regulators, it would work in conjunction with this
driver. When that other software adjusted a regulator's voltage then
this driver would handle telling the SoC about it. A good example is
vqmmc for SD. In that case the dw_mmc driver simply is told about a
regulator. It changes the regulator between 3.3V and 1.8V at the
right time. This driver notices the change and makes sure that the
SoC is on the same page.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[khilman: fix compiler warnings]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Disable the module option for POWER_AVS since this is currently not
supported.
This patch fixes these error in the case POWER_AVS is set to 'm':
arch/arm/mach-omap2/built-in.o: In function `sr_class3_configure':
arch/arm/mach-omap2/smartreflex-class3.c:43: undefined reference to `sr_configure_errgen'
arch/arm/mach-omap2/built-in.o: In function `sr_class3_disable':
arch/arm/mach-omap2/smartreflex-class3.c:33: undefined reference to `sr_disable_errgen'
arch/arm/mach-omap2/smartreflex-class3.c:35: undefined reference to `sr_disable'
arch/arm/mach-omap2/built-in.o: In function `sr_class3_enable':
arch/arm/mach-omap2/smartreflex-class3.c:28: undefined reference to `sr_enable'
arch/arm/mach-omap2/built-in.o: In function `sr_class3_init':
arch/arm/mach-omap2/smartreflex-class3.c:59: undefined reference to `sr_register_class'
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated to use relative paths for the build error]
Signed-off-by: Tony Lindgren <tony@atomide.com>
After a clean-up of the interfaces the OMAP Smartreflex IP driver is now a
generic driver. Move it to drivers/power/avs/.
The build is controlled by the following Kconfig options:
. CONFIG_POWER_AVS: general knob for Adaptive Voltage Scaling support,
. CONFIG_POWER_AVS_OMAP: AVS(Adaptive Voltage Scaling)
support on OMAP containing the version 1 or version 2 of the SmartReflex IP,
. CONFIG_POWER_AVS_OMAP_CLASS3: Class 3 implementation of Smartreflex.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
