Impact: change calling convention of existing cpumask APIs
Most cpumask functions started with cpus_: these have been replaced by
cpumask_ ones which take struct cpumask pointers as expected.
These four functions don't have good replacement names; fortunately
they're rarely used, so we just change them over.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: paulus@samba.org
Cc: mingo@redhat.com
Cc: tony.luck@intel.com
Cc: ralf@linux-mips.org
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: cl@linux-foundation.org
Cc: srostedt@redhat.com
This cleanup removes the resource assignment in pci_read_bridge_bases()
since it has taken care by pci_alloc_child_bus() when allocating the bus:
/* Set up default resource pointers and names.. */
for (i = 0; i < PCI_BRIDGE_RES_NUM; i++) {
child->resource[i] = &bridge->resource[PCI_BRIDGE_RESOURCES+i];
child->resource[i]->name = child->name;
}
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Some firmware fail to properly configure P2P bridges, leaving them
with invalid bus numbers. In some cases, this happens on some embedded
4xx boards as the result of the kernel allocating different bus space
than the firmware does to host bridges while not setting
pcibios_assign_all_busses() for various reasons. In other cases, it can
just be bogus firmware.
This adds some sanity checking to the PCI probing code. If a bridge is
found whose primary bus number doesn't match the bus it's sitting on,
or whose secondary bus number not strictly above it's primary bus
number, then the bridge bus numbers are deconfigured in the first pass
of pci_scan_bridge() to be re-assigned in the second pass.
Tested-by: "Ayman El-Khashab" <AymanE@tanisys.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This adds the ability to mmap legacy IO space to the legacy_io files
in sysfs on platforms that support it. This will allow to clean up
X to use this instead of /dev/mem for legacy IO accesses such as
those performed by Int10.
While at it I moved pci_create/remove_legacy_files() to pci-sysfs.c
where I think they belong, thus making more things statis in there
and cleaned up some spurrious prototypes in the ia64 pci.h file
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch uniformizes PCI probing debug boot messages with dev_printk()
intead of manual printk()
It changes adress range output from [%llx, %llx] to [%#llx-%#llx], like
in pci_request_region().
For example, it goes from the mixed-style:
PCI: 0000:00:1b.0 reg 10 64bit mmio: [f4280000, f4283fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
to uniform:
pci 0000:00:1b.0: reg 10 64bit mmio: [0xf4280000-0xf4283fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
This patch has been runtime tested, boot log messages diffed, everything
looks OK.
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Vincent Legoll <vincent.legoll@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch adds support for PCI Express Alternative Routing-ID
Interpretation (ARI) capability.
The ARI capability extends the Function Number field of the PCI Express
Endpoint by reusing the Device Number which is otherwise hardwired to 0.
With ARI, an Endpoint can have up to 256 functions.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch centralizes the initialization and release functions of
various PCI capabilities in probe.c, which makes the introduction
of new capability support functions cleaner in the future.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since patch 6ac665c63d my infiniband
controller hasn't worked. This is because it has 64-bit prefetchable
memory, which was mistakenly being taken to be 32-bit memory. The
resource flags in this case are PCI_BASE_ADDRESS_MEM_TYPE_64 |
PCI_BASE_ADDRESS_MEM_PREFETCH.
This patch checks only for the PCI_BASE_ADDRESS_MEM_TYPE_64 bit; thus
whether the region is prefetchable or not is ignored. This fixes my
Infiniband.
Reviewed-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is a cleanup that changes all PCI configuration space size
representations to the macros (PCI_CFG_SPACE_SIZE and
PCI_CFG_SPACE_EXP_SIZE). And the macros are also moved from
drivers/pci/probe.c to drivers/pci/pci.h.
Signed-off-by: Yu Zhao <yu.zhao@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The introduction of struct pci_slot (f46753c5e3)
added a struct pci_slot pointer to struct pci_dev, but we forgot to
associate the two.
Connect the two structs together; the interesting portions of the object
lifetimes are:
- when a new pci_slot is created, connect it to the appropriate
pci_dev's. A single pci_slot may be associated with multiple
pci_dev's, e.g. any multi-function PCI device.
- when a pci_slot is released, look for all the pci_dev's it was
associated with, and set their pci_slot pointers to NULL
- when a pci_dev is created, look for slots to associate with.
Note -- when a pci_dev is released, we don't need to do any bookkeeping,
since pci_slot's do not have pointers to pci_dev's.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use "[%04x:%04x]" for PCI vendor/device IDs to follow the format
used by lspci(8).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This converts things in drivers/pci to use %pR to printout the
content of a struct resource instead of hand-casted %llx or
other variants.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PCI core wants to reorder the devices in the bus list. So move this
functionality out of the pci core and into the driver core so that
anyone else can also do this if needed. This also lets us change how
struct device is attached to drivers in the future without messing with
the PCI core.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Print out for device BAR values before the kernel tries to update them.
Also make related output use KERN_DEBUG.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The cleaned up resource code in probe.c introduced some warnings:
drivers/pci/probe.c: In function 'pci_read_bridge_bases':
drivers/pci/probe.c:386: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'resource_size_t'
drivers/pci/probe.c:386: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/pci/probe.c:398: warning: format '%llx' expects type 'long long unsigned int', but argument 3 has type 'resource_size_t'
drivers/pci/probe.c:398: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/pci/probe.c:434: warning: format '%llx' expects type 'long long unsigned int', but argument 4 has type 'resource_size_t'
drivers/pci/probe.c:434: warning: format '%llx' expects type 'long long unsigned int', but argument 5 has type 'resource_size_t'
So fix them up.
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Check the return value of device_create_bin_file in pci_create_bus and
unwind if necessary. Don't propagate error to caller, as failure to create
these files shouldn't prevent PCI from being initialised. Instead, just
log a warning.
Cc: Sven Wegener <sven.wegener@stealer.net>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Disable ASPM on pre-1.1 PCIe devices, as many of them don't implement it
correctly.
Tested-by: Jack Howarth <howarth@bromo.msbb.uc.edu>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the kernel is configured to support 64-bit resources on a 32-bit
machine, we can support 64-bit BARs properly. Just change the condition
to check sizeof(resource_size_t) instead of BITS_PER_LONG.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Factor out the code to read one BAR from the loop in pci_read_bases into
a new function, __pci_read_base. The new code is slightly more
readable, better commented and removes the ifdef.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* Introduce function acpi_pm_device_sleep_wake() for enabling and
disabling the system wake-up capability of devices that are power
manageable by ACPI.
* Introduce function acpi_bus_can_wakeup() allowing other (dependent)
subsystems to check if ACPI is able to enable the system wake-up
capability of given device.
* Introduce callback .sleep_wake() in struct pci_platform_pm_ops and
for the ACPI PCI 'driver' make it use acpi_pm_device_sleep_wake().
* Introduce callback .can_wakeup() in struct pci_platform_pm_ops and
for the ACPI 'driver' make it use acpi_bus_can_wakeup().
* Move the PME# handlig code out of pci_enable_wake() and split it
into two functions, pci_pme_capable() and pci_pme_active(),
allowing the caller to check if given device is capable of
generating PME# from given power state and to enable/disable the
device's PME# functionality, respectively.
* Modify pci_enable_wake() to use the new ACPI callbacks and the new
PME#-related functions.
* Drop the generic .platform_enable_wakeup() callback that is not
used any more.
* Introduce device_set_wakeup_capable() that will set the
power.can_wakeup flag of given device.
* Rework PCI device PM initialization so that, if given device is
capable of generating wake-up events, either natively through the
PME# mechanism, or with the help of the platform, its
power.can_wakeup flag is set and its power.should_wakeup flag is
unset as appropriate.
* Make ACPI set the power.can_wakeup flag for devices found to be
wake-up capable by it.
* Make the ACPI wake-up code enable/disable GPEs for devices that
have the wakeup.flags.prepared flag set (which means that their
wake-up power has been enabled).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This changes pci_setup_device to handle pci_name() now returning a
constant string.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make pci_setup_device() write the bus ID directly into the allotted storage,
rather than using pci_name() as the address as that now returns a const
pointer.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Convert printks to use dev_printk().
I converted pr_debug() to dev_dbg(). Both use KERN_DEBUG and are enabled
only when DEBUG is defined.
I converted printk(KERN_DEBUG) to dev_printk(KERN_DEBUG), not to dev_dbg(),
because dev_dbg() is only enabled when DEBUG is defined.
I converted DBG(KERN_INFO) (only in setup-bus.c) to dev_info(). The DBG()
name makes it sound like debug, but it's been enabled forever, so dev_info()
preserves the previous behavior.
I tried to make the resource assignment formats more consistent, e.g.,
"BAR %d: got res [%#llx-%#llx] bus [%#llx-%#llx] flags %#lx\n"
instead of sometimes using "start-end" and sometimes using "size@start".
I'm not attached to one or the other; I'd just like them consistent.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Currently, /sys/bus/pci/slots/ only exposes hotplug attributes when a
hotplug driver is loaded, but PCI slots have attributes such as address,
speed, width, etc. that are not related to hotplug at all.
Introduce pci_slot as the primary data structure and kobject model.
Hotplug attributes described in hotplug_slot become a secondary
structure associated with the pci_slot.
This patch only creates the infrastructure that allows the separation of
PCI slot attributes and hotplug attributes. In this patch, the PCI
hotplug core remains the only user of this infrastructure, and thus,
/sys/bus/pci/slots/ will still only become populated when a hotplug
driver is loaded.
A later patch in this series will add a second user of this new
infrastructure and demonstrate splitting the task of exposing pci_slot
attributes from hotplug_slot attributes.
- Make pci_slot the primary sysfs entity. hotplug_slot becomes a
subsidiary structure.
o pci_create_slot() creates and registers a slot with the PCI core
o pci_slot_add_hotplug() gives it hotplug capability
- Change the prototype of pci_hp_register() to take the bus and
slot number (on parent bus) as parameters.
- Remove all the ->get_address methods since this functionality is
now handled by pci_slot directly.
[achiang@hp.com: rpaphp-correctly-pci_hp_register-for-empty-pci-slots]
Tested-by: Badari Pulavarty <pbadari@us.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: make headers_check happy]
[akpm@linux-foundation.org: nuther build fix]
[akpm@linux-foundation.org: fix typo in #include]
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Cc: Greg KH <greg@kroah.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If a device supports #PME and can generate PME events from D0, we may see
superfluous events before a driver is loaded (drivers should only enable PME as
needed), preventing suspend from working if the corresponding GPE was enabled.
Likewise, if the ACPI device has the _PRW object, the _PSW/_DSW object will be
called in order to disable the wakeup functionality. But when it is allowed to
wake up the sleeping state, OSPM will enable it again.
So we should disable PME in the course of scanning PCI devices and enable it
again only when PME events are actually required to be generated from the
requested PCI state (for example, D3_hot or D3_cold). It is also safe to
disable PME again when the PME is disabled for the PCI devices.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Li Shaohua <shaohua.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
so let pci_cfg_space_size call it directly without flag.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
scan AMD opteron io/mmio routing to make sure every pci root bus get correct
resource range. Thus later pci scan could assign correct resource to device
with unassigned resource.
this can fix a system without _CRS for multi pci root bus.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
in the device_add, we try to use use parent numa_node.
need to make sure pci root bus's bridge device numa_node is set.
then we could use device->numa_node direclty for all device.
and don't need to call pcibus_to_node().
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
reuse pci_cfg_space_size but skip check pci express and pci-x CAP ID.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
WARNING: drivers/pci/built-in.o(.text+0x150f): Section mismatch in reference from the function pci_scan_single_device() to the function .devinit.text:pci_scan_device()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
WARNING: drivers/pci/built-in.o(.text+0xc4c): Section mismatch in reference from the function pci_add_new_bus() to the function .devinit.text:pci_alloc_child_bus()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Done per Linus' request and suggestions. Linus has explained that
better than I'll be able to explain:
On Thu, Mar 27, 2008 at 10:12:10AM -0700, Linus Torvalds wrote:
> Actually, before we go any further, there might be a less intrusive
> alternative: add just a couple of flags to the resource flags field (we
> still have something like 8 unused bits on 32-bit), and use those to
> implement a generic "resource_alignment()" routine.
>
> Two flags would do it:
>
> - IORESOURCE_SIZEALIGN: size indicates alignment (regular PCI device
> resources)
>
> - IORESOURCE_STARTALIGN: start field is alignment (PCI bus resources
> during probing)
>
> and then the case of both flags zero (or both bits set) would actually be
> "invalid", and we would also clear the IORESOURCE_STARTALIGN flag when we
> actually allocate the resource (so that we don't use the "start" field as
> alignment incorrectly when it no longer indicates alignment).
>
> That wouldn't be totally generic, but it would have the nice property of
> automatically at least add sanity checking for that whole "res->start has
> the odd meaning of 'alignment' during probing" and remove the need for a
> new field, and it would allow us to have a generic "resource_alignment()"
> routine that just gets a resource pointer.
Besides, I removed IORESOURCE_BUS_HAS_VGA flag which was unused for ages.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vital Product Data (VPD) may be exposed by PCI devices in several
ways. It is generally unsafe to read this information through the
existing interfaces to user-land because of stateful interfaces.
This adds:
- abstract operations for VPD access (struct pci_vpd_ops)
- VPD state information in struct pci_dev (struct pci_vpd)
- an implementation of the VPD access method specified in PCI 2.2
(in access.c)
- a 'vpd' binary file in sysfs directories for PCI devices with VPD
operations defined
It adds a probe for PCI 2.2 VPD in pci_scan_device() and release of
VPD state in pci_release_dev().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Note: some devices might not work well with aspm, either because chipset
issue or device issue. The patch provide API (pci_disable_link_state),
driver can disable ASPM for specific device.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The PCI bus names included in /proc/iomem and /proc/ioports are
of the form 'PCI Bus #XX' where XX is the bus number. This patch
changes the naming to 'PCI Bus XXXX:YY' where XXXX is the domain
number and YY is the bus number. For example, PCI bus 14 in
domain 0 will show as 'PCI Bus 0000:14' instead of 'PCI Bus #14'.
This change makes the naming consistent with other architectures
such as ia64 where multiple PCI domain support has been around
longer.
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch finally removes the global list of PCI devices. We are
relying entirely on the list held in the driver core now, and do not
need a separate "shadow" list as no one uses it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This lets us check if the device is really added to the driver core or
not, which is what we need when walking some of the bus lists. The flag
is there in anticipation of getting rid of the other PCI device list,
which is what we used to check in this situation.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Cleaned up references to cpumask_scnprintf() and added new
cpulist_scnprintf() interfaces where appropriate.
* Fix some small bugs (or code efficiency improvments) for various uses
of cpumask_scnprintf.
* Clean up some checkpatch errors.
Signed-off-by: Mike Travis <travis@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix following warning:
WARNING: vmlinux.o(.text+0x47bdb1): Section mismatch in reference from the function pci_scan_child_bus() to the function .devinit.text:pcibios_fixup_bus()
We had plenty of functions that could be annotated __devinit but due to
the former restriction that exported symbols could not be annotated
they were not so. So annotate these function and fix the references
from the pci/hotplug/* code to silence the resuting warnings.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds PCI's accessor for segment_boundary_mask in device_dma_parameters.
The default segment_boundary is set to 0xffffffff, same to the block layer's
default value (and the scsi mid layer uses the same value).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds struct device_dma_parameters in struct pci_dev and properly
sets up a pointer in struct device.
The default max_segment_size is set to 64K, same to the block layer's
default value.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Mostly-acked-by: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following warnings were issued during build of
drivers/pci with an allyesconfig build:
WARNING: o-x86_64/drivers/pci/built-in.o(.text+0xdaf): Section mismatch in reference from the function pci_add_new_bus() to the function .devinit.text:pci_alloc_child_bus()
WARNING: o-x86_64/drivers/pci/built-in.o(.text+0x15e2): Section mismatch in reference from the function pci_scan_single_device() to the function .devinit.text:pci_scan_device()
WARNING: o-x86_64/drivers/pci/built-in.o(.text+0x1b0c5): Section mismatch in reference from the function pci_bus_assign_resources() to the function .devinit.text:pci_setup_bridge()
WARNING: o-x86_64/drivers/pci/built-in.o(.text+0x1b32d): Section mismatch in reference from the function pci_bus_size_bridges() to the function .devinit.text:pci_bus_size_cardbus()
Investigating each case closer it looked like all
referred functions are only used in the init phase
or during hotplug.
So to avoid wasting too much memory in the non-hotplug
case the simpler fix was to allow the fuctions to
use code/data from the __devinit sections.
This was done in all four case by adding the __ref
annotation.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix following warnings:
WARNING: o-x86_64/drivers/pci/built-in.o(.text+0xb054): Section mismatch in reference from the function cpci_configure_slot() to the function .devinit.text:pci_do_scan_bus()
WARNING: o-x86_64/drivers/pci/built-in.o(.text+0x153ab): Section mismatch in reference from the function shpchp_configure_device() to the function .devinit.text:pci_do_scan_bus()
WARNING: o-x86_64/drivers/pci/built-in.o(__ksymtab+0xc0): Section mismatch in reference from the variable __ksymtab_pci_do_scan_bus to the function .devinit.text:pci_do_scan_bus()
PCI hotplug were the only user of pci_do_scan_bus()
so moving this function to a separate file that is build
only when we enable CONFIG_HOTPLUG_PCI.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 6c723d5bd8.
It caused build errors on non-x86 platforms, config file confusion, and
even some boot errors on some x86-64 boxes. All around, not quite ready
for prime-time :(
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This moves the pci_bus class device to be a real struct device and at
the same time, place it in the device tree in the correct location.
Note, the old "bridge" symlink is now gone, but this was a non-standard
link and no userspace program used it. If you need to determine the
device that the bus is on, follow the standard device symlink, or walk
up the device tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
