There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add support to use the new compatible string "qcom,sdhci-msm-v5".
Based on the msm variant, pick the relevant variant data and
use it for register read/write to msm specific registers.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In addition to offsets of certain registers changing, the registers in
core_mem have been shifted to HC mem as well. To access these
registers, define msm version specific functions. These functions can
be loaded into the function pointers at the time of probe based on
the msm version detected.
Also defind new data structure to hold version specific Ops and
register addresses.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For SDCC version 5.0.0, MCI registers are removed from SDCC
interface and some registers are moved to HC.
Define a new data structure where we can statically define
the address offsets for the registers in different SDCC versions.
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Evan Green <evgreen@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now we have a proper implementation for the power irq handling and this
quirk is not needed anymore. In fact, it is causing card detection delays
on apq8096 platforms and the following error is displayed:
sdhci_msm 74a4900.sdhci: mmc0: pwr_irq for req: (4) timed out
The quirk is forcing the controller to retain 1.8V signalling on the slot
even when a new card is inserted, which is not correct. The proper behavior
would be to reset the controller in order to start with 3.3V signaling.
Fixes: c0309b3803 ("mmc: sdhci-msm: Add sdhci msm register write APIs which wait for pwr irq")
Suggested-by: Vijay Viswanath <vviswana@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The PADs for SD card are dual-voltage that support 3v/1.8v. Those PADs
have a control signal (io_pad_pwr_switch/mode18 ) that indicates
whether the PAD works in 3v or 1.8v.
SDHC core on msm platforms should have IO_PAD_PWR_SWITCH bit set/unset
based on actual voltage used for IO lines. So when power irq is
triggered for io high or io low, the driver should check the voltages
supported and set the pad accordingly.
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During probe check whether the vdd-io regulator of sdhc platform device
can support 1.8V and 3V and store this information as a capability of
platform device.
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Not all instances of the SDCC core supports changing signal voltage and
as such will not generate a power interrupt when the software attempts
to change the voltage. This results in probing the eMMC on some devices
to take over 2 minutes.
Check that the SWITCHABLE_SIGNALING_VOLTAGE bit in MCI_GENERICS is set
before waiting for the power interrupt.
Cc: Sahitya Tummala <stummala@codeaurora.org>
Cc: Vijay Viswanath <vviswana@codeaurora.org>
Fixes: c0309b3803 ("mmc: sdhci-msm: Add sdhci msm register write APIs which wait for pwr irq")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The __WARN_printf() function is not portable across architectures
and causes a compile-time error on x86 and others that don't use
the asm-generic version of asm/bug.h:
drivers/mmc/host/sdhci-msm.c: In function 'sdhci_msm_check_power_status':
drivers/mmc/host/sdhci-msm.c:1066:4: error: implicit declaration of function '__WARN_printf'; did you mean '__dev_printk'? [-Werror=implicit-function-declaration]
__WARN_printf("%s: pwr_irq for req: (%d) timed out\n",
^~~~~~~~~~~~~
The change that introduced this error, "mmc: sdhci-msm: Add sdhci msm
register write APIs which wait for pwr irq", likely meant to use
dev_warn(), so I'm changing over to that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Register writes which change voltage of IO lines or turn the IO bus
on/off require controller to be ready before progressing further. When
the controller is ready, it will generate a power irq which needs to be
handled. The thread which initiated the register write should wait for
power irq to complete. This will be done through the new sdhc msm write
APIs which will check whether the particular write can trigger a power
irq and wait for it with a timeout if it is expected.
The SDHC core power control IRQ gets triggered when -
* There is a state change in power control bit (bit 0)
of SDHCI_POWER_CONTROL register.
* There is a state change in 1.8V enable bit (bit 3) of
SDHCI_HOST_CONTROL2 register.
* Bit 1 of SDHCI_SOFTWARE_RESET is set.
Also add support APIs which are used by sdhc msm write APIs to check
if power irq is expected to be generated and wait for the power irq
to come and complete if the irq is expected.
This patch requires CONFIG_MMC_SDHCI_IO_ACCESSORS to be enabled.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is a rare scenario in HW, where the first clear pulse could
be lost when the actual reset and clear/read of status register
are happening at the same time. Fix this by retrying upto 10 times
to ensure the status register gets cleared. Otherwise, this will
lead to a spurious power IRQ which results in system instability.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDCC controller reset (SW_RST) during probe may trigger power irq if
previous status of PWRCTL was either BUS_ON or IO_HIGH_V. So before we
enable the power irq interrupt in GIC (by registering the interrupt
handler), we need to ensure that any pending power irq interrupt status
is acknowledged otherwise power irq interrupt handler would be fired
prematurely.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The delay circuit used to support HS400 is calibrated based on two
additional clocks. When these clocks are not available and
FF_CLK_SW_RST_DIS is not set in CORE_HC_MODE, reset might fail. But on
some platforms this doesn't work properly and below dump can be seen in
the kernel log.
mmc0: Reset 0x1 never completed.
mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc0: sdhci: Sys addr: 0x00000000 | Version: 0x00001102
mmc0: sdhci: Blk size: 0x00004000 | Blk cnt: 0x00000000
mmc0: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
mmc0: sdhci: Present: 0x01f80000 | Host ctl: 0x00000000
mmc0: sdhci: Power: 0x00000000 | Blk gap: 0x00000000
mmc0: sdhci: Wake-up: 0x00000000 | Clock: 0x00000002
mmc0: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
mmc0: sdhci: Int enab: 0x00000000 | Sig enab: 0x00000000
mmc0: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
mmc0: sdhci: Caps: 0x742dc8b2 | Caps_1: 0x00008007
mmc0: sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
mmc0: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000
mmc0: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
mmc0: sdhci: Host ctl2: 0x00000000
mmc0: sdhci: ============================================
Add support for the additional calibration clocks to allow these
platforms to be configured appropriately.
Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
By stuffing the runtime controlled clocks into a clk_bulk_data array we
can utilize the newly introduced bulk clock operations and clean up the
error paths. This allow us to handle additional clocks in subsequent
patch, without the added complexity.
Cc: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Programming legacy HOST SDMA Buffer Boundary bits in Block Size Register
(0x04) is not supported in Qualcomm sdhci controllers. Writing to this
would cause the controller not to transfer last block in case block size
is 4 bytes or less.
This issue was noticed while testing sdio wlan card on Qcom DB410c board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The spin lock is not necessary in set_ios. Anything that is racing with
changes to the I/O state is already broken. The mmc core already provides
synchronization via "claiming" the host. So remove spin_lock and friends
from sdhci_set_ios and related callbacks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
This removes CDC init sequence comments which are
not useful anyway.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
platform_execute_tuning should not really exist as it does not
do anything useful.
So remove this ops and directly plug sdhci_msm_execute_tuning
with mmc_host_ops.
Also in case of HS400 tuning clear SDHCI_HS400_TUNING flag once
HS400 related mode selection is done.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This provides enhanced_strobe mode feature support in sdhci-msm
driver.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
During tuning execution for HS400 mode, HW sequence recommends
to select MCLK_SEL/2(0x3) in VENDOR_SPEC & sdhc msm clock at GCC
to be 400MHZ (nearest supported clk). Add this change in tuning
sequence during HS400 tuning.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Program CORE_CSR_CDC_DELAY_CFG for hardware recommended 1.25ns delay.
We may see data CRC errors if it's programmed for any other delay
value.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The vendor specific func register doesn't get reset when using the
software reset register. The various bootloader's could leave this
in an unknown state, hence reset this register to it's power on reset
value during probe.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out sdhci_msm_hs400 used for DLL calibration in HS400
modes. This function will be needed for enhanced_strobe as well.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Factor out msm_set/get_clock_rate_for_bus_mode for it's later
use in changing the tuning sequence for selecting HS400
bus speed mode.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This factors out sdhci_msm_hc_select_mode to later use
it during enhanced_strobe mode select.
It also further breaks sdhci_msm_hc_select_mode
into separate functions for configuring HS400 mode
or other modes.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The newer msm sdhci's cores use a different DLL hardware for HS400.
Update the configuration and calibration of the newer DLL block.
The HS400 DLL block used previously is CDC LP 533 and requires
programming multiple registers and waiting for configuration to
complete and then enable it. It has about 18 register writes and
two register reads.
The newer HS400 DLL block is SDC4 DLL and requires two register
writes for configuration and one register read to confirm that it
is initialized. There is an additional register write to enable
the power save mode for SDC4 DLL block.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Krishna Konda <kkonda@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In HS400 mode a new RCLK is introduced on the interface for read data
transfers. The eMMC5.0 device transmits the read data to the host with
respect to rising and falling edges of RCLK. In order to ensure correct
operation of read data transfers in HS400 mode, the incoming RX data
needs to be sampled by delayed version of RCLK.
The CDCLP533 delay circuit shifts the RCLK by T/4. It needs to be
initialized, configured and enabled once during HS400 mode switch and
when operational voltage/clock is changed.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Save the tuning phase once the tuning is performed.
This phase value will be used while calibrating DLL
for HS400 mode.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The following msm platform specific changes are added to support HS400.
- Allow tuning for HS400 mode.
- Configure HS400 timing mode using the VENDOR_SPECIFIC_FUNC register.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDHC MSM controller need 2x clock for MCLK at GCC.
Hence make required changes to have 2x clock for
DDR timing modes.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
sdhci-msm controller may have different clk-rates for each
bus speed mode. Thus implement set_clock callback for
sdhci-msm driver.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This add get_min_clock() and get_max_clock() callback
for sdhci-msm. sdhci-msm min/max clocks may be different
hence implement these callbacks.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDCC core with minor version >= 0x42 introduced new 14lpp
DLL. This has additional requirements in the reset sequence
for DLL tuning. Make necessary changes as needed.
Without this patch we see below errors on such SDHC controllers
sdhci_msm 7464900.sdhci: mmc0: DLL failed to LOCK
mmc0: tuning execution failed: -110
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch changes the poor style of writel/readl registers
into more readable format. This avoid mixed style format
of readl/writel in sdhci-msm driver.
This patch also removes the one line comments which were present for
above writel/readl, since they were of no help.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Provides runtime PM callbacks to enable and disable clock resources
when idle. Also support system PM callbacks to be called during system
suspend and resume.
Reviewed-by: Ritesh Harjani <riteshh@codeaurora.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Pramod Gurav <pramod.gurav@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fix to return a negative error code from the platform_get_irq_byname()
error handling case instead of 0, as done elsewhere in this function.
Fixes: ad81d38710 ("mmc: sdhci-msm: Add support for UHS cards")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enabling support for ultra high speed mode cards requires some
voltage switching and interaction with the PMIC via a special
power IRQ. Add support for this.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To allow UHS mode to work properly, we need to implement a Qualcomm
specific set_uhs_signaling() callback function. This function differs
from the sdhci_set_uhs_signaling() in that we need check the clock
rate and enable UHS timing only if the frequency is above 100MHz.
This patch resolves the mmc_select_hs200 timeouts noticed after merging
commit a5c1f3e55c99 ("mmc: mmc: do not use CMD13 to get status after
speed mode switch")
mmc0: mmc_select_hs200 failed, error -110
mmc0: error -110 whilst initialising MMC card
mmc0: Reset 0x1 never completed.
sdhci: =========== REGISTER DUMP (mmc0)===========
sdhci: Sys addr: 0x00000000 | Version: 0x00002e02
sdhci: Blk size: 0x00004000 | Blk cnt: 0x00000000
sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
sdhci: Present: 0x01f80000 | Host ctl: 0x00000000
sdhci: Power: 0x00000000 | Blk gap: 0x00000000
sdhci: Wake-up: 0x00000000 | Clock: 0x00000003
sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
sdhci: Int enab: 0x00000000 | Sig enab: 0x00000000
sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
sdhci: Caps: 0x322dc8b2 | Caps_1: 0x00008007
sdhci: Cmd: 0x00000000 | Max curr: 0x00000000
sdhci: Host ctl2: 0x00000000
sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x0000000000000000
sdhci: ===========================================
Fixes: a5c1f3e55c99 ("mmc: mmc: do not use CMD13 to get status after...")
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The controller does not clear the "reset bit" when it is reset without
a card in the slot. Because of this, the following error message is seen
while booting with no plugged SD card.
mmc1: Reset 0x1 never completed.
Add the SDHCI_QUIRK_NO_CARD_NO_RESET quirk to avoid this.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-msm
to this allocation.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There's no need to allocate one sdhci_msm_pdata for each sdhci_msm_host.
This patch removes the sdhci_msm_pdata member from sdhci_msm_host and
uses one static global sdhci_msm_pdata for all sdhci msm hosts. It also
marks sdhci_msm_ops as const.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_execute_tuning() has already prepared the opcode,
there is no need to prepare it again at mmc_send_tuning(),
and, there is a BUG of mmc_send_tuning() to determine the opcode
by bus width, assume eMMC was running at HS200, 4bit mode,
then the mmc_send_tuning() will overwrite the opcode from CMD21
to CMD19, then got error.
in addition, extend an argument of "cmd_error" to allow getting
if there was cmd error when tune response.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
[Ulf: Rebased patch]
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ensure SDCC is working with maximum clock otherwise card
detection could be extremely slow, up to 7 seconds.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some versions of this controller do not advertise their 3.0v and
8bit bus-width support capabilities. It is required to explicitly
set these capabilities for the specific controller versions.
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Georgi Djakov <gdjakov@mm-sol.com>
Acked-by: Georgi Djakov <gdjakov@mm-sol.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we're tuning on a big-endian CPU we'll never determine we properly
tuned the device because we compare the data we received from the
controller with a table that assumes the CPU is little-endian.
Change the table to be an array of bytes instead of 32-bit words
so we can use memcmp() without needing to byte-swap every word
depending on the endianess of the CPU.
Cc: Asutosh Das <asutoshd@codeaurora.org>
Cc: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Reviewed-by: Georgi Djakov <gdjakov@mm-sol.com>
Fixes: 415b5a75da "mmc: sdhci-msm: Add platform_execute_tuning implementation"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
weiyongjun (A)