The size of the VPD area is not necessarily 4-byte aligned, so a
pci_vpd_read() might return less than 4 bytes. Zero our buffer and
accept anything other than an error. Intel X710 NICs exercise this.
Fixes: 4e1a635552 ("vfio/pci: Use kernel VPD access functions")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Both the INTx and MSI/X disable paths do an eventfd_ctx_put() for the
trigger eventfd before calling vfio_virqfd_disable() any potential
mask and unmask eventfds. This opens a use-after-free race where an
inopportune irqfd can reference the freed signalling eventfd. Reorder
to avoid this possibility.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
PCI-Express spec says that reading 4 bytes at offset 100h should return
zero if there is no extended capability so VFIO reads this dword to
know if there are extended capabilities.
However it is not always possible to access the extended space so
generic PCI code in pci_cfg_space_size_ext() checks if
pci_read_config_dword() can read beyond 100h and if the check fails,
it sets the config space size to 100h.
VFIO does its own extended capabilities check by reading at offset 100h
which may produce 0xffffffff which VFIO treats as the extended config
space presense and calls vfio_ecap_init() which fails to parse
capabilities (which is expected) but right before the exit, it writes
zero at offset 100h which is beyond the buffer allocated for
vdev->vconfig (which is 256 bytes) which leads to random memory
corruption.
This makes VFIO only check for the extended capabilities if
the discovered config size is more than 256 bytes.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
If a device is reset without the memory or i/o bits enabled in the
command register we may not detect it, potentially leaving the device
without valid BAR programming. Add an additional test to check the
BARs on each write to the command register.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
INTx masking has two components, the first is that we need the ability
to prevent the device from continuing to assert INTx. This is
provided via the DisINTx bit in the command register and is the only
thing we can really probe for when testing if INTx masking is
supported. The second component is that the device needs to indicate
if INTx is asserted via the interrupt status bit in the device status
register. With these two features we can generically determine if one
of the devices we own is asserting INTx, signal the user, and mask the
interrupt while the user services the device.
Generally if one or both of these components is broken we resort to
APIC level interrupt masking, which requires an exclusive interrupt
since we have no way to determine the source of the interrupt in a
shared configuration. This often makes it difficult or impossible to
configure the system for userspace use of the device, for an interrupt
mode that the user may not need.
One possible configuration of broken INTx masking is that the DisINTx
support is fully functional, but the interrupt status bit never
signals interrupt assertion. In this case we do have the ability to
prevent the device from asserting INTx, but lack the ability to
identify the interrupt source. For this case we can simply pretend
that the device lacks INTx support entirely, keeping DisINTx set on
the physical device, virtualizing this bit for the user, and
virtualizing the interrupt pin register to indicate no INTx support.
We already support virtualization of the DisINTx bit and already
virtualize the interrupt pin for platforms without INTx support. By
tying these components together, setting DisINTx on open and reset,
and identifying devices broken in this particular way, we can provide
support for them w/o the handicap of APIC level INTx masking.
Intel i40e (XL710/X710) 10/20/40GbE NICs have been identified as being
broken in this specific way. We leave the vfio-pci.nointxmask option
as a mechanism to bypass this support, enabling INTx on the device
with all the requirements of APIC level masking.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Various enablers for assignment of Intel graphics devices and future
support of vGPU devices (Alex Williamson). This includes
- Handling the vfio type1 interface as an API rather than a specific
implementation, allowing multiple type1 providers.
- Capability chains, similar to PCI device capabilities, that allow
extending ioctls. Extensions here include device specific regions
and sparse mmap descriptions. The former is used to expose non-PCI
regions for IGD, including the OpRegion (particularly the Video
BIOS Table), and read only PCI config access to the host and LPC
bridge as drivers often depend on identifying those devices.
Sparse mmaps here are used to describe the MSIx vector table,
which vfio has always protected from mmap, but never had an API to
explicitly define that protection. In future vGPU support this is
expected to allow the description of PCI BARs that may mix direct
access and emulated access within a single region.
- The ability to expose the shadow ROM as an option ROM as IGD use
cases may rely on the ROM even though the physical device does not
make use of a PCI option ROM BAR.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=/lJn
-----END PGP SIGNATURE-----
Merge tag 'vfio-v4.6-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
"Various enablers for assignment of Intel graphics devices and future
support of vGPU devices (Alex Williamson). This includes
- Handling the vfio type1 interface as an API rather than a specific
implementation, allowing multiple type1 providers.
- Capability chains, similar to PCI device capabilities, that allow
extending ioctls. Extensions here include device specific regions
and sparse mmap descriptions. The former is used to expose non-PCI
regions for IGD, including the OpRegion (particularly the Video
BIOS Table), and read only PCI config access to the host and LPC
bridge as drivers often depend on identifying those devices.
Sparse mmaps here are used to describe the MSIx vector table, which
vfio has always protected from mmap, but never had an API to
explicitly define that protection. In future vGPU support this is
expected to allow the description of PCI BARs that may mix direct
access and emulated access within a single region.
- The ability to expose the shadow ROM as an option ROM as IGD use
cases may rely on the ROM even though the physical device does not
make use of a PCI option ROM BAR"
* tag 'vfio-v4.6-rc1' of git://github.com/awilliam/linux-vfio:
vfio/pci: return -EFAULT if copy_to_user fails
vfio/pci: Expose shadow ROM as PCI option ROM
vfio/pci: Intel IGD host and LCP bridge config space access
vfio/pci: Intel IGD OpRegion support
vfio/pci: Enable virtual register in PCI config space
vfio/pci: Add infrastructure for additional device specific regions
vfio: Define device specific region type capability
vfio/pci: Include sparse mmap capability for MSI-X table regions
vfio: Define sparse mmap capability for regions
vfio: Add capability chain helpers
vfio: Define capability chains
vfio: If an IOMMU backend fails, keep looking
vfio/pci: Fix unsigned comparison overflow
Calling return copy_to_user(...) in an ioctl will not
do the right thing if there's a pagefault:
copy_to_user returns the number of bytes not copied
in this case.
Fix up vfio to do
return copy_to_user(...)) ?
-EFAULT : 0;
everywhere.
Cc: stable@vger.kernel.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The copy_to_user() function returns the number of bytes that were not
copied but we want to return -EFAULT on error here.
Fixes: 188ad9d6cb ('vfio/pci: Include sparse mmap capability for MSI-X table regions')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Integrated graphics may have their ROM shadowed at 0xc0000 rather than
implement a PCI option ROM. Make this ROM appear to the user using
the ROM BAR.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Provide read-only access to PCI config space of the PCI host bridge
and LPC bridge through device specific regions. This may be used to
configure a VM with matching register contents to satisfy driver
requirements. Providing this through the vfio file descriptor removes
an additional userspace requirement for access through pci-sysfs and
removes the CAP_SYS_ADMIN requirement that doesn't appear to apply to
the specific devices we're accessing.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This is the first consumer of vfio device specific resource support,
providing read-only access to the OpRegion for Intel graphics devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Typically config space for a device is mapped out into capability
specific handlers and unassigned space. The latter allows direct
read/write access to config space. Sometimes we know about registers
living in this void space and would like an easy way to virtualize
them, similar to how BAR registers are managed. To do this, create
one more pseudo (fake) PCI capability to be handled as purely virtual
space. Reads and writes are serviced entirely from virtual config
space.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add support for additional regions with indexes started after the
already defined fixed regions. Device specific code can register
these regions with the new vfio_pci_register_dev_region() function.
The ops structure per region currently only includes read/write
access and a release function, allowing automatic cleanup when the
device is closed. mmap support is only missing here because it's
not needed by the first user queued for this support.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
vfio-pci has never allowed the user to directly mmap the MSI-X vector
table, but we've always relied on implicit knowledge of the user that
they cannot do this. Now that we have capability chains that we can
expose in the region info ioctl and a sparse mmap capability that
represents the sub-areas within the region that can be mmap'd, we can
make the mmap constraints more explicit.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed versus unsigned comparisons are implicitly cast to unsigned,
which result in a couple possible overflows. For instance (start +
count) might overflow and wrap, getting through our validation test.
Also when unwinding setup, -1 being compared as unsigned doesn't
produce the intended stop condition. Fix both of these and also fix
vfio_msi_set_vector_signal() to validate parameters before using the
vector index, though none of the callers should pass bad indexes
anymore.
Reported-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
There is really no way to safely give a user full access to a DMA
capable device without an IOMMU to protect the host system. There is
also no way to provide DMA translation, for use cases such as device
assignment to virtual machines. However, there are still those users
that want userspace drivers even under those conditions. The UIO
driver exists for this use case, but does not provide the degree of
device access and programming that VFIO has. In an effort to avoid
code duplication, this introduces a No-IOMMU mode for VFIO.
This mode requires building VFIO with CONFIG_VFIO_NOIOMMU and enabling
the "enable_unsafe_noiommu_mode" option on the vfio driver. This
should make it very clear that this mode is not safe. Additionally,
CAP_SYS_RAWIO privileges are necessary to work with groups and
containers using this mode. Groups making use of this support are
named /dev/vfio/noiommu-$GROUP and can only make use of the special
VFIO_NOIOMMU_IOMMU for the container. Use of this mode, specifically
binding a device without a native IOMMU group to a VFIO bus driver
will taint the kernel and should therefore not be considered
supported. This patch includes no-iommu support for the vfio-pci bus
driver only.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Revert commit 033291eccb ("vfio: Include No-IOMMU mode") due to lack
of a user. This was originally intended to fill a need for the DPDK
driver, but uptake has been slow so rather than support an unproven
kernel interface revert it and revisit when userspace catches up.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This pci_error_handlers structure is never modified, like all the other
pci_error_handlers structures, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
- Use kernel interfaces for VPD emulation (Alex Williamson)
- Platform fix for releasing IRQs (Eric Auger)
- Type1 IOMMU always advertises PAGE_SIZE support when smaller
mapping sizes are available (Eric Auger)
- Platform fixes for incorrectly using copies of structures rather
than pointers to structures (James Morse)
- Rework platform reset modules, fix leak, and add AMD xgbe reset
module (Eric Auger)
- Fix vfio_device_get_from_name() return value (Joerg Roedel)
- No-IOMMU interface (Alex Williamson)
- Fix potential out of bounds array access in PCI config handling
(Dan Carpenter)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bI62
-----END PGP SIGNATURE-----
Merge tag 'vfio-v4.4-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- Use kernel interfaces for VPD emulation (Alex Williamson)
- Platform fix for releasing IRQs (Eric Auger)
- Type1 IOMMU always advertises PAGE_SIZE support when smaller mapping
sizes are available (Eric Auger)
- Platform fixes for incorrectly using copies of structures rather than
pointers to structures (James Morse)
- Rework platform reset modules, fix leak, and add AMD xgbe reset
module (Eric Auger)
- Fix vfio_device_get_from_name() return value (Joerg Roedel)
- No-IOMMU interface (Alex Williamson)
- Fix potential out of bounds array access in PCI config handling (Dan
Carpenter)
* tag 'vfio-v4.4-rc1' of git://github.com/awilliam/linux-vfio:
vfio/pci: make an array larger
vfio: Include No-IOMMU mode
vfio: Fix bug in vfio_device_get_from_name()
VFIO: platform: reset: AMD xgbe reset module
vfio: platform: reset: calxedaxgmac: fix ioaddr leak
vfio: platform: add dev_info on device reset
vfio: platform: use list of registered reset function
vfio: platform: add compat in vfio_platform_device
vfio: platform: reset: calxedaxgmac: add reset function registration
vfio: platform: introduce module_vfio_reset_handler macro
vfio: platform: add capability to register a reset function
vfio: platform: introduce vfio-platform-base module
vfio/platform: store mapped memory in region, instead of an on-stack copy
vfio/type1: handle case where IOMMU does not support PAGE_SIZE size
VFIO: platform: clear IRQ_NOAUTOEN when de-assigning the IRQ
vfio/pci: Use kernel VPD access functions
vfio: Whitelist PCI bridges
Smatch complains about a possible out of bounds error:
drivers/vfio/pci/vfio_pci_config.c:1241 vfio_cap_init()
error: buffer overflow 'pci_cap_length' 20 <= 20
The problem is that pci_cap_length[] was defined as large enough to
hold "PCI_CAP_ID_AF + 1" elements. The code in vfio_cap_init() assumes
it has PCI_CAP_ID_MAX + 1 elements. Originally, PCI_CAP_ID_AF and
PCI_CAP_ID_MAX were the same but then we introduced PCI_CAP_ID_EA in
commit f80b0ba959 ("PCI: Add Enhanced Allocation register entries")
so now the array is too small.
Let's fix this by making the array size PCI_CAP_ID_MAX + 1. And let's
make a similar change to pci_ext_cap_length[] for consistency. Also
both these arrays can be made const.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
There is really no way to safely give a user full access to a DMA
capable device without an IOMMU to protect the host system. There is
also no way to provide DMA translation, for use cases such as device
assignment to virtual machines. However, there are still those users
that want userspace drivers even under those conditions. The UIO
driver exists for this use case, but does not provide the degree of
device access and programming that VFIO has. In an effort to avoid
code duplication, this introduces a No-IOMMU mode for VFIO.
This mode requires building VFIO with CONFIG_VFIO_NOIOMMU and enabling
the "enable_unsafe_noiommu_mode" option on the vfio driver. This
should make it very clear that this mode is not safe. Additionally,
CAP_SYS_RAWIO privileges are necessary to work with groups and
containers using this mode. Groups making use of this support are
named /dev/vfio/noiommu-$GROUP and can only make use of the special
VFIO_NOIOMMU_IOMMU for the container. Use of this mode, specifically
binding a device without a native IOMMU group to a VFIO bus driver
will taint the kernel and should therefore not be considered
supported. This patch includes no-iommu support for the vfio-pci bus
driver only.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
The PCI VPD capability operates on a set of window registers in PCI
config space. Writing to the address register triggers either a read
or write, depending on the setting of the PCI_VPD_ADDR_F bit within
the address register. The data register provides either the source
for writes or the target for reads.
This model is susceptible to being broken by concurrent access, for
which the kernel has adopted a set of access functions to serialize
these registers. Additionally, commits like 932c435cab ("PCI: Add
dev_flags bit to access VPD through function 0") and 7aa6ca4d39
("PCI: Add VPD function 0 quirk for Intel Ethernet devices") indicate
that VPD registers can be shared between functions on multifunction
devices creating dependencies between otherwise independent devices.
Fortunately it's quite easy to emulate the VPD registers, simply
storing copies of the address and data registers in memory and
triggering a VPD read or write on writes to the address register.
This allows vfio users to avoid seeing spurious register changes from
accesses on other devices and enables the use of shared quirks in the
host kernel. We can theoretically still race with access through
sysfs, but the window of opportunity is much smaller.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Mark Rustad <mark.d.rustad@intel.com>
This patch adds the registration/unregistration of an
irq_bypass_producer for MSI/MSIx on vfio pci devices.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Feng Wu <feng.wu@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Testing the driver for a PCI device is racy, it can be all but
complete in the release path and still report the driver as ours.
Therefore we can't trust drvdata to be valid. This race can sometimes
be seen when one port of a multifunction device is being unbound from
the vfio-pci driver while another function is being released by the
user and attempting a bus reset. The device in the remove path is
found as a dependent device for the bus reset of the release path
device, the driver is still set to vfio-pci, but the drvdata has
already been cleared, resulting in a null pointer dereference.
To resolve this, fix vfio_device_get_from_dev() to not take the
dev_get_drvdata() shortcut and instead traverse through the
iommu_group, vfio_group, vfio_device path to get a reference we
can trust. Once we have that reference, we know the device isn't
in transition and we can test to make sure the driver is still what
we expect, so that we don't interfere with devices we don't own.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Log some clues indicating whether the user is receiving device
request interfaces or not listening. This can help indicate why a
driver unbind is blocked or explain why QEMU automatically unplugged
a device from the VM.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We can save some power by putting devices that are bound to vfio-pci
but not in use by the user in the D3hot power state. Devices get
woken into D0 when opened by the user. Resets return the device to
D0, so we need to re-apply the low power state after a bus reset.
It's tempting to try to use D3cold, but we have no reason to inhibit
hotplug of idle devices and we might get into a loop of having the
device disappear before we have a chance to try to use it.
A new module parameter allows this feature to be disabled if there are
devices that misbehave as a result of this change.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
As indicated in the comment, this is not entirely uncommon and
causes user concern for no reason.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This copies the same support from pci-stub for exactly the same
purpose, enabling a set of PCI IDs to be automatically added to the
driver's dynamic ID table at module load time. The code here is
pretty simple and both vfio-pci and pci-stub are fairly unique in
being meta drivers, capable of attaching to any device, so there's no
attempt made to generalize the code into pci-core.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
If VFIO VGA access is disabled for the user, either by CONFIG option
or module parameter, we can often opt-out of VGA arbitration. We can
do this when PCI bridge control of VGA routing is possible. This
means that we must have a parent bridge and there must only be a
single VGA device below that bridge. Fortunately this is the typical
case for discrete GPUs.
Doing this allows us to minimize the impact of additional GPUs, in
terms of VGA arbitration, when they are only used via vfio-pci for
non-VGA applications.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Add a module option so that we don't require a CONFIG change and
kernel rebuild to disable VGA support. Not only can VGA support be
troublesome in itself, but by disabling it we can reduce the impact
to host devices by doing a VGA arbitration opt-out.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
An unintended consequence of commit 42ac9bd18d ("vfio: initialize
the virqfd workqueue in VFIO generic code") is that the vfio module
is renamed to vfio_core so that it can include both vfio and virqfd.
That's a user visible change that may break module loading scritps
and it imposes eventfd support as a dependency on the core vfio code,
which it's really not. virqfd is intended to be provided as a service
to vfio bus drivers, so instead of wrapping it into vfio.ko, we can
make it a stand-alone module toggled by vfio bus drivers. This has
the additional benefit of removing initialization and exit from the
core vfio code.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Now we have finally completely decoupled virqfd from VFIO_PCI. We can
initialize it from the VFIO generic code, in order to safely use it from
multiple independent VFIO bus drivers.
Signed-off-by: Antonios Motakis <a.motakis@virtualopensystems.com>
Signed-off-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The virqfd functionality that is used by VFIO_PCI to implement interrupt
masking and unmasking via an eventfd, is generic enough and can be reused
by another driver. Move it to a separate file in order to allow the code
to be shared.
Signed-off-by: Antonios Motakis <a.motakis@virtualopensystems.com>
Signed-off-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
VFIO_PCI passes the VFIO device structure *vdev via eventfd to the handler
that implements masking/unmasking of IRQs via an eventfd. We can replace
it in the virqfd infrastructure with an opaque type so we can make use
of the mechanism from other VFIO bus drivers.
Signed-off-by: Antonios Motakis <a.motakis@virtualopensystems.com>
Signed-off-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The Virqfd code needs to keep accesses to any struct *virqfd safe, but
this comes into play only when creating or destroying eventfds, so sharing
the same spinlock with the VFIO bus driver is not necessary.
Signed-off-by: Antonios Motakis <a.motakis@virtualopensystems.com>
Signed-off-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
The functions vfio_pci_virqfd_init and vfio_pci_virqfd_exit are not really
PCI specific, since we plan to reuse the virqfd code with more VFIO drivers
in addition to VFIO_PCI.
Signed-off-by: Antonios Motakis <a.motakis@virtualopensystems.com>
[Baptiste Reynal: Move rename vfio_pci_virqfd_init and vfio_pci_virqfd_exit
from "vfio: add a vfio_ prefix to virqfd_enable and virqfd_disable and export"]
Signed-off-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We want to reuse virqfd functionality in multiple VFIO drivers; before
moving these functions to core VFIO, add the vfio_ prefix to the
virqfd_enable and virqfd_disable functions, and export them so they can
be used from other modules.
Signed-off-by: Antonios Motakis <a.motakis@virtualopensystems.com>
Signed-off-by: Baptiste Reynal <b.reynal@virtualopensystems.com>
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
This adds a missing break statement to VFIO_DEVICE_SET_IRQS handler
without which vfio_pci_set_err_trigger() would never be called.
While we are here, add another "break" to VFIO_PCI_REQ_IRQ_INDEX case
so if we add more indexes later, we won't miss it.
Fixes: 6140a8f562 ("vfio-pci: Add device request interface")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Userspace can opt to receive a device request notification,
indicating that the device should be released. This is setup
the same way as the error IRQ and also supports eventfd signaling.
Future support may forcefully remove the device from the user if
the request is ignored.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
We want another single vector IRQ index to support signaling of
the device request to userspace. Generalize the error reporting
IRQ index to avoid code duplication.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Current vfio-pci just supports normal pci device, so vfio_pci_probe() will
return if the pci device is not a normal device. While current code makes a
mistake. PCI_HEADER_TYPE is the offset in configuration space of the device
type, but we use this value to mask the type value.
This patch fixs this by do the check directly on the pci_dev->hdr_type.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org # v3.6+
- s390 support (Frank Blaschka)
- Enable iommu-type1 for ARM SMMU (Will Deacon)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1L2V
-----END PGP SIGNATURE-----
Merge tag 'vfio-v3.19-rc1' of git://github.com/awilliam/linux-vfio
Pull VFIO updates from Alex Williamson:
- s390 support (Frank Blaschka)
- Enable iommu-type1 for ARM SMMU (Will Deacon)
* tag 'vfio-v3.19-rc1' of git://github.com/awilliam/linux-vfio:
drivers/vfio: allow type-1 IOMMU instantiation on top of an ARM SMMU
vfio: make vfio run on s390
Rename write_msi_msg() to pci_write_msi_msg() to mark it as PCI
specific.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
add Kconfig switch to hide INTx
add Kconfig switch to let vfio announce PCI BARs are not mapable
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Locking both the remove() and release() path results in a deadlock
that should have been obvious. To fix this we can get and hold the
vfio_device reference as we evaluate whether to do a bus/slot reset.
This will automatically block any remove() calls, allowing us to
remove the explict lock. Fixes 61d792562b.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org [3.17]
The MSIx vector table lives in device memory, which may be cleared as
part of a backdoor device reset. This is the case on the IBM IPR HBA
when the BIST is run on the device. When assigned to a QEMU guest,
the guest driver does a pci_save_state(), issues a BIST, then does a
pci_restore_state(). The BIST clears the MSIx vector table, but due
to the way interrupts are configured the pci_restore_state() does not
restore the vector table as expected. Eventually this results in an
EEH error on Power platforms when the device attempts to signal an
interrupt with the zero'd table entry.
Fix the problem by restoring the host cached MSI message prior to
enabling each vector.
Reported-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
In PCIe r1.0, sec 5.10.2, bit 0 of the Uncorrectable Error Status, Mask,
and Severity Registers was for "Training Error." In PCIe r1.1, sec 7.10.2,
bit 0 was redefined to be "Undefined."
Rename PCI_ERR_UNC_TRAIN to PCI_ERR_UNC_UND to reflect this change.
No functional change.
[bhelgaas: changelog]
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The existing vfio_pci_open() fails upon error returned from
vfio_spapr_pci_eeh_open(), which breaks POWER7's P5IOC2 PHB
support which this patch brings back.
The patch fixes the issue by dropping the return value of
vfio_spapr_pci_eeh_open().
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Alex Williamson