PREEMPT (and PREEMPT AND ABORT) should return CONFLICT iff a specified
SERVICE ACTION RESERVATION KEY is specified and matches no existing
persistent reservation.
Without this patch, a PREEMPT will return CONFLICT if either all
reservations are held by the initiator (self preemption) or there is
nothing to preempt. According to the spec, both of these cases should
succeed.
Signed-off-by: Steven Allen <steven.allen@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a force_pr_aptpl device attribute used to force SPC-3 PR
Activate Persistence across Target Power Loss (APTPL) operation. This
makes PR metadata write-out occur during state change regardless if new
PERSISTENT_RESERVE_OUT CDBs have their APTPL feature bit set.
This is useful during H/A failover in active/passive setups where all PR
state is being re-created on a different node, driven by configfs backend
device + export layout and pre-loaded $DEV/pr/res_aptpl_metadata.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug in handling of SPC-3 PR Activate Persistence
across Target Power Loss (APTPL) logic where re-creation of state for
MappedLUNs from dynamically generated NodeACLs did not occur during
I_T Nexus establishment.
It adds the missing core_scsi3_check_aptpl_registration() call during
core_tpg_check_initiator_node_acl() -> core_tpg_add_node_to_devs() in
order to replay any pre-loaded APTPL metadata state associated with
the newly connected SCSI Initiator Port.
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The target code has a rather generous helping of smp_mb__after_atomic()
throughout the code base. Most atomic operations were followed by one
and none were preceded by smp_mb__before_atomic(), nor accompanied by a
comment explaining the need for a barrier.
Instead of trying to prove for every case whether or not it is needed,
this patch introduces atomic_inc_mb() and atomic_dec_mb(), which
explicitly include the memory barriers before and after the atomic
operation. For now they are defined in a target header, although they
could be of general use.
Most of the existing atomic/mb combinations were replaced by the new
helpers. In a few cases the atomic was sandwiched in
spin_lock/spin_unlock and I simply removed the barrier.
I suspect that in most cases the correct conversion would have been to
drop the barrier. I also suspect that a few cases exist where a) the
barrier was necessary and b) a second barrier before the atomic would
have been necessary and got added by this patch.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Clearly a right-shift was meant. Effectively doesn't make a difference,
as add_len is hard-coded to 8 and the high byte will be zero no matter
which way you shift. But I hate leaving bad examples for others to
copy.
Found by coverity.
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a >= v3.11 free-after-use regression
in core_scsi3_emulate_pro_register() that was introduced
in the following commit:
commit bc118fe4c4
Author: Andy Grover <agrover@redhat.com>
Date: Thu May 16 10:41:04 2013 -0700
target: Further refactoring of core_scsi3_emulate_pro_register()
To avoid the free-after-use, save an type value before hand, and
only call core_scsi3_put_pr_reg() with a valid *pr_reg.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org> #3.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Update copyright ownership/year information for target-core,
loopback, iscsi-target, tcm_qla2xx, vhost and iser-target.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a >= v3.9+ regression in __core_scsi3_write_aptpl_to_file()
+ core_alua_write_tpg_metadata() write-out, where a return value of -EIO was
incorrectly being returned upon success.
This bug was originally introduced in:
commit 0e9b10a90f
Author: Al Viro <viro@zeniv.linux.org.uk>
Date: Sat Feb 23 15:22:43 2013 -0500
target: writev() on single-element vector is pointless
However, given that the return of core_scsi3_update_and_write_aptpl()
was not used to determine if a command should be returned with non GOOD
status, this bug was not being triggered in PR logic until v3.11-rc1 by
commit:
commit 459f213ba1
Author: Andy Grover <agrover@redhat.com>
Date: Thu May 16 10:41:02 2013 -0700
target: Allocate aptpl_buf inside update_and_write_aptpl()
So, go ahead and only return -EIO if kernel_write() returned a
negative value.
Reported-by: Gera Kazakov <gkazakov@msn.com>
Signed-off-by: Gera Kazakov <gkazakov@msn.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org # 3.9+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix up sense_reason_t breakage in core_scsi3_update_and_write_aptpl()
from recent conversion to use local scope memory allocation.
Reported as sparse warnings: (new ones prefixed by >>) by Fengguang:
>> drivers/target/target_core_pr.c:2069:57: sparse: incorrect type in
>> return expression (different base types)
drivers/target/target_core_pr.c:2069:57: expected restricted sense_reason_t
drivers/target/target_core_pr.c:2069:57: got int
>> drivers/target/target_core_pr.c:2179:21: sparse: incorrect type in
>> assignment (different base types)
drivers/target/target_core_pr.c:2179:21: expected restricted sense_reason_t [assigned] [usertype] ret
drivers/target/target_core_pr.c:2179:21: got int
>> drivers/target/target_core_pr.c:2197:13: sparse: incorrect type in
>> assignment (different base types)
drivers/target/target_core_pr.c:2197:13: expected restricted sense_reason_t [assigned] [usertype] ret
drivers/target/target_core_pr.c:2197:13: got int
drivers/target/target_core_pr.c:1245:28: sparse: context imbalance in '__core_scsi3_free_registration' - unexpected unlock
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Use bool params when appropriate.
Eliminate unneeded pr_reg_e and type variables.
Just one goto label, so rename to 'out' from 'out_put_pr_reg'.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Don't need goto, we can just do an if/else for sa_res_key behavior. Move
shorter case first. Slightly shorter b/c both cases can share a call to
update_and_write_aptpl() now.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of taking the buffer and length, update_and_write_aptpl() will
allocate the buffer as needed, and then free it. Instead, the function
takes an 'aptpl' boolean parameter.
This enables us to remove memory alloc/frees from struct
t10_pr_registration and other spots.
There is a slight loss of functionality because each callsite doesn't get
its own pr_debug any more, but this info can be cleaned via ftrace if
necessary and I think the shorter code is worth it.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As mentioned in the comments in update_and_write_aptpl,
write_aptpl_to_file() calls strlen() on the buffer, and the length was
always being passed as zero.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It's only ever set to PR_APTPL_BUF_LEN, so we don't need a variable.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The __ version is only ever called from the regular version, so just
inline it. It's not too much more complex to handle both spinlocks in the
same function.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Simpler to just set buf in update_and_write_aptpl(), rather than passing
down to ____core_scsi3_update_aptpl_buf().
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
They're in emulate_pro_register, so change UNREGISTER to REGISTER.
The first one seems wrong -- sa_res_key could be 0 there, but it's testing
spec_i_pt.
Remove unneeded parens in 2nd conditional.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We use this function exclusively in debug prints. Instead of returning
0 or 1 if isid is present, just set buf to "" if it isn't there. This
saves callers from having to check the return value.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
core_scsi3_enulate_pro_register took an 'ignore_key' parameter that
really distinguished between REGISTER and REGISTER_AND_IGNORE_EXISTING_KEY
registration types, which was a little confusing. Same situation for
PREEMPT and PREEMPT_AND_ABORT. Use enums to add a little more
descriptiveness to the code.
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
... in other news:
filp_open() can't return a struct file with NULL dentry
filp_open() can't return a struct file negative dentry
filp_close() of something that never had been in any descriptor
tables is pointless - fput() is all you need
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The compiler complained about uninitialized variables, so
use TCM_NO_SENSE here.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Nicholas Bellinger <nab@risingtidesystems.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
v2: Use correct target_core_stat.c 2006 copyright year
v3: Drop extra unnessary legal verbage from header (hch)
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fix a regression bug in core_scsi3_emulate_pro_release() where
should still be getting released via core_scsi3_put_pr_reg() during
No persistent reservation, with returing GOOD status.
Use goto statement here to follow converted code from hch.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pass the sense reason as an explicit return value from the I/O submission
path instead of storing it in struct se_cmd and using negative return
values. This cleans up a lot of the code pathes, and with the sparse
annotations for the new sense_reason_t type allows for much better
error checking.
(nab: Convert spc_emulate_modesense + spc_emulate_modeselect to use
sense_reason_t with Roland's MODE SELECT changes)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We do not support host-level reservations for the pscsi backend, and all
virtual backends are newere than SCSI-2, so just make the combined
SPC-3 + SCSI-2 support the only supported variant and kill the switches
for the different implementations, given that this code handles the no-op
version just fine.
(hch: Update DRF_SPC2_RESERVATIONS lock usage)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Simplify the code a lot by killing the superflous struct se_subsystem_dev.
Instead se_device is allocated early on by the backend driver, which allocates
it as part of its own per-device structure, borrowing the scheme that is for
example used for inode allocation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The dereference should be moved below the NULL test.
spatch with a semantic match is used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Correct spelling typo in printk and comment within drivers/target.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Several places were not checking that the parameter list length
was large enough, and thus accessing invalid memory. Zero-length
parameter lists are just a special case of this.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- instead of (PTR_ERR(file) < 0) just use IS_ERR(file)
- return -EINVAL instead of EINVAL
- all other error returns in target_scsi3_emulate_pr_out() use
"goto out" -- get rid of the one remaining straight "return."
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull scsi-target changes from Nicholas Bellinger:
"There has been lots of work in existing code in a number of areas this
past cycle. The major highlights have been:
* Removal of transport_do_task_sg_chain() from core + fabrics
(Roland)
* target-core: Removal of se_task abstraction from target-core and
enforce hw_max_sectors for pSCSI backends (hch)
* Re-factoring of iscsi-target tx immediate/response queues (agrover)
* Conversion of iscsi-target back to using target core memory
allocation logic (agrover)
We've had one last minute iscsi-target patch go into for-next to
address a nasty regression bug related to the target core allocation
logic conversion from agrover that is not included in friday's
linux-next build, but has been included in this series.
On the new fabric module code front for-3.5, here is a brief status
update for the three currently in flight this round:
* usb-gadget target driver:
Sebastian Siewior's driver for supporting usb-gadget target mode
operation. This will be going out as a separate PULL request from
target-pending/usb-target-merge with subsystem maintainer ACKs. There
is one minor target-core patch in this series required to function.
* sbp ieee-1394/firewire target driver:
Chris Boot's driver for supportting the Serial Block Protocol (SBP)
across IEEE-1394 Firewire hardware. This will be going out as a
separate PULL request from target-pending/sbp-target-merge with two
additional drivers/firewire/ patches w/ subsystem maintainer ACKs.
* qla2xxx LLD target mode infrastructure changes + tcm_qla2xxx:
The Qlogic >= 24xx series HW target mode LLD infrastructure patch-set
and tcm_qla2xxx fabric driver. Support for FC target mode using
qla2xxx LLD code has been officially submitted by Qlogic to James
below, and is currently outstanding but not yet merged into
scsi.git/for-next..
[PATCH 00/22] qla2xxx: Updates for scsi "misc" branch
http://www.spinics.net/lists/linux-scsi/msg59350.html
Note there are *zero* direct dependencies upon this for-next series
for the qla2xxx LLD target + tcm_qla2xxx patches submitted above, and
over the last days the target mode team has been tracking down an
tcm_qla2xxx specific active I/O shutdown bug that appears to now be
almost squashed for 3.5-rc-fixes."
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (47 commits)
iscsi-target: Fix iov_count calculation bug in iscsit_allocate_iovecs
iscsi-target: remove dead code in iscsi_check_valuelist_for_support
target: Handle ATA_16 passthrough for pSCSI backend devices
target: Add MI_REPORT_TARGET_PGS ext. header + implict_trans_secs attribute
target: Fix MAINTENANCE_IN service action CDB checks to use lower 5 bits
target: add support for the WRITE_VERIFY command
target: make target_put_session void
target: cleanup transport_execute_tasks()
target: Remove max_sectors device attribute for modern se_task less code
target: lock => unlock typo in transport_lun_wait_for_tasks
target: Enforce hw_max_sectors for SCF_SCSI_DATA_SG_IO_CDB
target: remove the t_se_count field in struct se_cmd
target: remove the t_task_cdbs_ex_left field in struct se_cmd
target: remove the t_task_cdbs_left field in struct se_cmd
target: remove struct se_task
target: move the state and execute lists to the command
target: simplify command to task linkage
target: always allocate a single task
target: replace ->execute_task with ->execute_cmd
target: remove the task_sectors field in struct se_task
...
This patch addresses a bug in a special case for target core SPC-2 RELEASE
logic where the same physical client (eg: iSCSI InitiatorName) with
differing iSCSI session identifiers (ISID) is allowed to incorrectly release
the same client's SPC-2 reservation from the non reservation holding path.
Note this bug is specific to iscsi-target w/ SPC-2 reservations, and
with the default enforce_pr_isids=1 device attr setting in target-core
controls if a InitiatorName + different ISID reservations are handled
the same as a single iSCSI client entity.
Signed-off-by: Bernhard Kohl <bernhard.kohl@gmx.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Make CDB emulation work on commands instead of tasks again as a preparation
of removing tasks completely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch includes the handful of squashed patches for target/iscsi from
Andy's original series into lio-core/master code:
*) Make iscsit_add_reject static
*) Remove unused data_offset_end from iscsi_datain_req
*) Remove "#if 0" stubs
*) Rename iscsi_datain_req to cmd_datain_node
*) Cleanups for built_r2ts_for_cmd()
*) Cleanups for Cleanup build_sendtargets_response()
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull SCSI target updates from Nicholas Bellinger:
"This contains the usual set of updates and bugfixes to target-core +
existing fabric module code, along with a handful of the patches
destined for v3.3 stable.
It also contains the necessary target-core infrastructure pieces
required to run using tcm_qla2xxx.ko WWPNs with the new Qlogic Fibre
Channel fabric module currently queued in target-pending/for-next-merge,
and coming for round 2.
The highlights for this series include:
- Add target_submit_tmr() helper function for fabric task management
(andy)
- Convert tcm_fc to use target_submit_tmr() (andy)
- Replace target core various cmd flags with a transport state (hch)
- Convert loopback to use workqueue submission (hch)
- Convert target core to use array_zalloc for tpg_lun_list (joern)
- Convert target core to use array_zalloc for device_list (joern)
- Add target core support for TMR_ABORT_TASK (nab)
- Add target core se_sess->sess_kref + get/put helpers (nab)
- Add target core se_node_acl->acl_kref for ->acl_free_comp usage
(nab)
- Convert iscsi-target to use target_put_session + sess_kref (nab)
- Fix tcm_fc fc_exch memory leak in ft_send_resp_status (nab)
- Fix ib_srpt srpt_handle_cmd send_ioctx->ioctx_kref leak on
exception (nab)
- Fix target core up handling of short INQUIRY buffers (roland)
- Untangle target-core front-end and back-end meanings of max_sectors
attribute (roland)
- Set loopback residual field for SCSI commands (roland)
- Fix target-core 16-bit target ports for SET TARGET PORT GROUPS
emulation (roland)
Thanks again to Andy, Christoph, Joern, Roland, and everyone who has
contributed this round!"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (64 commits)
ib_srpt: Fix srpt_handle_cmd send_ioctx->ioctx_kref leak on exception
loopback: Fix transport_generic_allocate_tasks error handling
iscsi-target: remove improper externs
iscsi-target: Remove unused variables in iscsi_target_parameters.c
target: remove obvious warnings
target: Use array_zalloc for device_list
target: Use array_zalloc for tpg_lun_list
target: Fix sense code for unsupported SERVICE ACTION IN
target: Remove hack to make READ CAPACITY(10) lie if thin provisioning is enabled
target: Bump core version to v4.1.0-rc2-ml + fabric versions
tcm_fc: Fix fc_exch memory leak in ft_send_resp_status
target: Drop unused legacy target_core_fabric_ops API callers
iscsi-target: Convert to use target_put_session + sess_kref
target: Convert se_node_acl->acl_group removal to use ->acl_kref
target: Add se_node_acl->acl_kref for ->acl_free_comp usage
target: Add se_node_acl->acl_free_comp for NodeACL release path
target: Add se_sess->sess_kref + get/put helpers
target: Convert session_lock to irqsave
target: Fix typo in drivers/target
iscsi-target: Fix dynamic -> explict NodeACL pointer reference
...
Get rid of a bunch of write-only variables. In a number of cases I
suspect actual bugs to be present, so I left all of those for a second
look.
(nab: fix lio-core patch fuzz)
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Turns an order-8 allocation into slab-sized ones, thereby preventing
allocation failures with memory fragmentation.
This likely saves memory as well, as the slab allocator can pack objects
more tightly than the buddy allocator.
(nab: Fix lio-core patch fuzz)
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch addresses a bug with target_check_scsi2_reservation_conflict()
return checking in target_scsi2_reservation_[reserve,release]() that was
preventing CRH=1 operation from silently succeeding in the two special
cases defined by SPC-3, and not failing with reservation conflict status
when dealing with legacy RESERVE/RELEASE + active SPC-3 PR logic.
Also explictly set cmd->scsi_status = SAM_STAT_RESERVATION_CONFLICT during
the early non reservation holder failure from pr_ops->t10_seq_non_holder()
check in transport_generic_cmd_sequencer() for fabrics that already expect
it to be set.
This bug was originally introduced in mainline commit:
commit eacac00ce5
Author: Christoph Hellwig <hch@infradead.org>
Date: Thu Nov 3 17:50:40 2011 -0400
target: split core_scsi2_emulate_crh
Reported-by: Martin Svec <martin.svec@zoner.cz>
Cc: Martin Svec <martin.svec@zoner.cz>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Instead of
static struct list_head foo;
static struct mutex bar;
...
INIT_LIST_HEAD(&foo);
mutex_init(&bar);
just do
static LIST_HEAD(foo);
static DEFINE_MUTEX(bar);
Also remove some superfluous struct list_head and spinlock_t
initialization calls where the variables are already defined using
macros that initialize them.
This saves a decent amount of compiled code too:
add/remove: 0/0 grow/shrink: 0/3 up/down: 0/-178 (-178)
function old new delta
target_core_init_configfs 898 850 -48
core_scsi3_emulate_pro_preempt 1742 1683 -59
iscsi_thread_set_init 159 88 -71
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We need to handle >1 page control cdbs, so extend the code to do a vmap
if bigger than 1 page. It seems like kmap() is still preferable if just
a page, fewer TLB shootdowns(?), so keep using that when possible.
Rename function pair for their new scope.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Initiators that aren't the active reservation holder should be able to
do a PERSISTENT RESERVE IN command in all cases, so add it to the list
of allowed CDBs in core_scsi3_pr_seq_non_holder().
Signed-off-by: Marco Sanvido <marco@purestorage.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The comments quote the right parts of the spec:
* d) Establish a unit attention condition for the
* initiator port associated with every I_T nexus
* that lost its registration other than the I_T
* nexus on which the PERSISTENT RESERVE OUT command
* was received, with the additional sense code set
* to REGISTRATIONS PREEMPTED.
and
* e) Establish a unit attention condition for the initiator
* port associated with every I_T nexus that lost its
* persistent reservation and/or registration, with the
* additional sense code set to REGISTRATIONS PREEMPTED;
but the actual code accidentally uses ASCQ_2AH_RESERVATIONS_PREEMPTED
instead of ASCQ_2AH_REGISTRATIONS_PREEMPTED. Fix this.
Signed-off-by: Marco Sanvido <marco@purestorage.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This reorganized the headers under include/target into:
- target_core_base.h stays as is with all target-wide data stuctures and defines
- target_core_backend.h contains the whole interface to I/O backends
- target_core_fabric.h contains the whole interface to fabric modules
Except for those only the various configfs macro headers stay around.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Create a new headers, drivers/target/target_core_internal.h that is supposed
to hold all target_core-internal prototypes. Move all non-exported includes
from include/target to it, and merge the smaller prototype-only includes
inside drivers/target into it as well. Mark functions that were found to
not be called outside their implementation file static.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch removes legacy usage of PYX_TRANSPORT_* return codes in a number
of locations and addresses cases where transport_generic_request_failure()
was returning the incorrect sense upon CHECK_CONDITION status after the
v3.1 converson to use errno return codes.
This includes the conversion of transport_generic_request_failure() to
process cmd->scsi_sense_reason and handle extra TCM_RESERVATION_CONFLICT
before calling transport_send_check_condition_and_sense() to queue up
response status. It also drops PYX_TRANSPORT_OUT_OF_MEMORY_RESOURCES legacy
usgae, and returns TCM_LOGICAL_UNIT_COMMUNICATION_FAILURE w/ a response
for these cases.
transport_generic_allocate_tasks(), transport_generic_new_cmd(), backend
SCF_SCSI_DATA_SG_IO_CDB ->do_task(), and emulated ->execute_task() have
all been updated to set se_cmd->scsi_sense_reason and return errno codes
universally upon failure. This includes cmd->scsi_sense_reason assignment
in target_core_alua.c, target_core_pr.c and target_core_cdb.c emulation code.
Finally it updates fabric modules to remove the legacy usage, and for
TFO->new_cmd_map() callers forwards return values outside of fabric code.
iscsi-target has also been updated to remove a handful of special cases
related to the cleanup and signaling QUEUE_FULL handling w/ ft_write_pending()
(v2: Drop extra SCF_SCSI_CDB_EXCEPTION check during failure from
transport_generic_new_cmd, and re-add missing task->task_error_status
assignment in transport_complete_task)
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
