HiFive unleashed A00 board has VSC8541-01 ethernet phy, this device is
identified as a Revision B device as described in device identification
registers. In order to use this phy in the unmanaged mode, it requires
a specific reset sequence of logical 0-1-0-1 transition on the NRESET pin
as documented here [1].
Currently, the bootloader (fsbl or u-boot-spl) takes care of the phy reset.
If due to some reason the phy device hasn't received the reset by the prior
stages before the linux macb driver comes into the picture, the MACB mii
bus gets probed but the mdio scan fails and is not even able to read the
phy ID registers. It gives an error message:
"libphy: MACB_mii_bus: probed
mdio_bus 10090000.ethernet-ffffffff: MDIO device at address 0 is missing."
Thus adding the device OUI (Organizationally Unique Identifier) to the phy
device node helps to probe the phy device.
[1]: VSC8541-01 datasheet:
https://www.mouser.com/ds/2/523/Microsemi_VSC8541-01_Datasheet_10496_V40-1148034.pdf
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Add the ability to reboot the HiFive Unleashed board via GPIO.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
Add a default "stdout-path" to the kernel DTS file, as is present in many
of the board DTS files elsewhere in the kernel tree. With this line
present, earlyconsole can be enabled by simply passing "earlycon" on the
kernel command line. No specific device details are necessary, since the
kernel will use the stdout-path as the default.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
DT node for SiFive FU540-C000 GEMGXL Ethernet controller driver added
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Sagar Kadam <sagar.kadam@sifive.com>
Cc: Andrew Lunn <andrew@lunn.ch>
[paul.walmsley@sifive.com: changed "phy1" to "phy0" at Andrew Lunn's
suggestion]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
As per the convention for any SOC device with external connection,
define only device DT node in SOC DTSi file with status = "disabled"
and enable device in Board DTS file with status = "okay"
Reported-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Add initial board data for the SiFive HiFive Unleashed A00.
Currently the data populated in this DT file describes the board
DRAM configuration and the external clock sources that supply the
PRCI.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Loys Ollivier <lollivier@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Sagar Shrikant Kadam