In case of unknown DT compatible device the ASRC OF node
possibly acquired earlier by of_parse_phandle() has
to be put before returning from probe method.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
add wm8960 support for fsl-asoc-card
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adjust set DAI format function in fsl_ssi driver
so it doesn't fail and clears RXDIR in AC'97 mode.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instantiate AC'97 CODEC in fsl_ssi driver AC'97 mode.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check whether setting AC'97 ops succeeded and clean them
on removal so the fsl_ssi driver can be reloaded.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC'97 bus can support asymmetric playback/capture rates
so enable them in this case in fsl_ssi driver.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC'97 DAI driver struct need the same probe method as
I2S one to setup DMA params in fsl_ssi driver.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
IPG clock have to be enabled during AC'97 CODEC register
access in fsl_ssi driver.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dev->name of CODEC might not be identical to its codec_dai_name,
so using dev->name to probe the CODEC dai is not a correct approach.
This patch specifies each supporting codec_dai_name instead of using
dev->name any more.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are too much noise about the typos for fsl's drivers. So I fix
all the typos here in this patch in almost every file I touched.
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add 32 bit word length support. There are no code changes required
in the SAI driver since it has already wirten the word width to the
corresponding register.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need "i" to be signed or it leads to a forever loop in the error
handling.
Fixes: fa3be9208d ('ASoC: fsl: fsl_spdif: Check for clk_prepare_enable() error')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the datasheet 'pm', 'psr' and 'div2' should never be all 0.
Since commit 541b03ad6c ("ASoC: fsl_ssi: Fix the incorrect limitation of
the bit clock rate") this can happen, because for some bitclock rates
'pm' = 0 seems to be a valid choice but does not work due to hardware
restrictions. This results into a bad hardware behaviour (slow audio for
example). Feature tested on a i.MX25.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the ssi is not the only cpu dai, there are esai, spdif, sai.
and imx_pcm_dma can be used by all of them. Especially ESAI need
a larger DMA buffer size. So Add dedicated DMA buffer for each cpu
dai.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
My static checker complains that:
sound/soc/fsl/imx-wm8962.c:196 imx_wm8962_probe() warn:
we tested 'ret' before and it was 'false'
The intent was that we use "ret" to check imx_audmux_v2_configure_port().
Fixes: 8de2ae2a7f ('ASoC: fsl: add imx-wm8962 machine driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Otherwise, Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As commit 6c8ca30eec ("ASoC: fsl_ssi: Don't try to round-up for PM
divisor calculation") mentioned that there's no more need to use a
round up work around to get a better divisor since the clk-divider
driver has been refined a lot.
So this patch applies the same modification to fsl_spdif driver.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Normally we don't support 12kHz, 24kHz in audio driver, alsa didn't
have formal definition of 12kHz, 24kHz, but alsa supply a way to
support these sample rates. And add 176.4kHz and 192kHz support.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When sai works on master mode, set its bit clock and frame clock.
SAI has 4 MCLK source, bus clock, MCLK1, MCLK2 and MCLK3. fsl_sai_set_bclk
will select proper MCLK source, then calculate and set the bit clock divider.
After fsl_sai_set_bclk, enable the selected mclk in hw_params(), and add
hw_free() to disable the mclk.
Signed-off-by: Zidan Wang <zidan.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify a trivial if-return sequence. Possibly combine with a
preceding function call.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/simple_return.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bool initializations should use true and false. Bool tests don't need
comparisons. Based on contributions from Joe Perches, Rusty Russell
and Bruce W Allan.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/boolinit.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The comment and the call to of_device_is_available() are not really
needed.
It is the expected behaviour to probe only the ssi nodes that are
enabled in the device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Whether residue can be reported or not is not a property of the audio
controller but of the DMA controller. The FLAG_NO_RESIDUE was initially
added when the DMAengine framework had no support for describing the residue
reporting capabilities of the controller. Support for this was added quite a
while ago and recently the DMAengine framework started to complain if a
driver does not describe its capabilities and a lot of patches have been
merged that add support for this where it was missing. So it should be safe
to assume that driver on actively used platforms properly implement the DMA
capabilities API.
This patch makes the FLAG_NO_RESIDUE internal and no longer allows audio
controller drivers to manually set the flag. If a DMA driver against
expectations does not support reporting its capabilities for now the generic
DMAengine PCM driver will now emit a warning and simply assume that residue
reporting is not supported. In the future this might be changed to aborting
with an error.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should check whether platform_get_irq() returns a negative number and
propagate the error in this case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU960DAAoJECTWi3JdVIfQkKIH/RDvxRn8dvKOPF5U9Uix3chH
JWKkzqfsMP0EpmQTzCQPp0ShAyYcWSbYsopicynPxUem5vS4Z8+UmOgEEgkj59pK
USbF6v1jCQXA6BcbKyUcRRBD9FtRkfVDc7mYbRs2CcwQz2CGCgee41cvPM+2BT+z
QdNC9UJARSweGvE1IUJSfpfYOly+BJ2s0/28RaQ0PGt+I0auoYx7IMFgMSDjv2p6
PY0kyQiwm3Kyj2uNXPZ5gEuPxlw/t8n4fbQNrBYAvxzN+EF5NrGdKE3N7MI1xRV/
EkFhzy+uM3X9c37tb2lT2fgPFlBc9rgPuLPSyoQ6nxa5ghCqAlgRhzpxRem8hhU=
=VlCw
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.1' into asoc-next
ASoC: Changes for v4.1
A selection of changes for v4.1 so far. The main things are:
- Move of jack registration to the card where it belongs.
- Support for DAPM routes specified by both the machine driver and DT.
# gpg: Signature made Thu 05 Mar 2015 01:10:27 GMT using RSA key ID 5D5487D0
# gpg: WARNING: digest algorithm MD5 is deprecated
# gpg: please see https://gnupg.org/faq/weak-digest-algos.html for more information
# gpg: Oops: keyid_from_fingerprint: no pubkey
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
The dapm field of the snd_soc_codec struct will eventually be removed
(replaced with the DAPM context from the component embedded inside the
CODEC). Replace its usage with the card's DAPM context. The idea is that
DAPM is hierarchical and with the card at the root it is possible to access
widgets from other contexts through the card context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To keep consistency with the other Kconfig entries, use the audio
interface acronyms (SSI and SPDIF) in the Kconfig menu text.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using platform_get_resource() and devm_ioremap_resource() can make the
code a bit simpler.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using devm_snd_soc_register_component() can make the code shorter and
cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
driver fixes for new regressions since v3.19. Second are fixes to the
common clock divider type caused by recent changes to how we round clock
rates. This affects many clock drivers that use this common code.
Finally there are fixes for drivers that improperly compared struct clk
pointers (drivers must not deref these pointers). While some of these
drivers have done this for a long time, this did not cause a problem
until we started generating unique struct clk pointers for every
consumer. A new function, clk_is_match was introduced to get these
drivers working again and they are fixed up to no longer deref the
pointers themselves.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVBewEAAoJEKI6nJvDJaTUR2gP/2frIXCm/krwkDyofIGxxQ+F
RwIXFTn9GG9QEUwKLUcxRUegHbWbZMXYp6W19hUcUdYz3pD+uEJSuH0NI8kW1Ohy
32P5/ALuoTq7OVzBBz/9di9jBDdIM1wusLZGJfOWk9DXBLOS3VHuhN55D47dqWS/
GsszeEpp8r1WBKFVmAkuQ5Jc0CqgS5GxvMOndXXVN3kDMhCT+9pBiqtUT0V3YV/J
d5GCvfPlO/Xmjnpjf99MPButkfiW/o6YXt3H0QY6hhskS1Av8alyfabVctk8lqOW
py8SQFY7MdRLZ84Zk87sqKCKUc/vHkTBT9vKWYm65l3yJ5OEFv60NaFMYY61HVlJ
n6qWU6SbFZvkPnQTJn6Ii/v7BQ92bXjYpLNcBK8UY35jIjmHsPS/YXCbkmArtn1N
/yAB4TIfH8uX93smFb3XEmZLSiKFuZAhU8YbjDzYgsGuQ9EwN3aNP9c5mzC7Soou
tYnDqVic0i993qQTD2Db5dplGwxelCRJpazO2kK6NW/EJzE8XJaM6XVy1xIBKiDX
bbWPdp53/eWV7gbUEZ8zzcS06G/DLw5/N45XyaWIx+2ThDjhOAlVHTAFDY+Oa743
42Dkwtr5GZ6yORyXY1wI5HttUGU0gnPN0kM84GQG8O/GbzGureZSW1e6G7tJJljn
JXhROl0w4aIPwUUxry7R
=nc5C
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clock framework fixes from Michael Turquette:
"The clk fixes for 4.0-rc4 comprise three themes.
First are the usual driver fixes for new regressions since v3.19.
Second are fixes to the common clock divider type caused by recent
changes to how we round clock rates. This affects many clock drivers
that use this common code.
Finally there are fixes for drivers that improperly compared struct
clk pointers (drivers must not deref these pointers). While some of
these drivers have done this for a long time, this did not cause a
problem until we started generating unique struct clk pointers for
every consumer. A new function, clk_is_match was introduced to get
these drivers working again and they are fixed up to no longer deref
the pointers themselves"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
ASoC: kirkwood: fix struct clk pointer comparing
ASoC: fsl_spdif: fix struct clk pointer comparing
ARM: imx: fix struct clk pointer comparing
clk: introduce clk_is_match
clk: don't export static symbol
clk: divider: fix calculation of initial best divider when rounding to closest
clk: divider: fix selection of divider when rounding to closest
clk: divider: fix calculation of maximal parent rate for a given divider
clk: divider: return real rate instead of divider value
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: fix platform_no_drv_owner.cocci warnings
clk: qcom: Add PLL4 vote clock
clk: qcom: lcc-msm8960: Fix PLL rate detection
clk: qcom: Fix slimbus n and m val offsets
clk: ti: Fix FAPLL parent enable bit handling
Since commit 035a61c314 ("clk: Make clk API return per-user struct clk
instances"), clk API users can no longer check if two struct clk
pointers are pointing to the same hardware clock, i.e. struct clk_hw, by
simply comparing two pointers. That's because with the per-user clk
change, a brand new struct clk is created whenever clients try to look
up the clock by calling clk_get() or sister functions like clk_get_sys()
and of_clk_get(). This changes the original behavior where the struct
clk is only created for once when clock driver registers the clock to
CCF in the first place. The net change here is before commit
035a61c314 the struct clk pointer is unique for given hardware
clock, while after the commit the pointers returned by clk lookup calls
become different for the same hardware clock.
That said, the struct clk pointer comparing in the code doesn't work any
more. Call helper function clk_is_match() instead to fix the problem.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Michael Turquette <mturquette@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
According to i.MX6 Series Reference Manual, the formula to calculate
the sys clock is
sysclk rate = bclk rate * (div2 + 1) * (7 * psr + 1) * (pm + 1) * 2
Commit aafa85e71a ("ASoC: fsl_ssi: Add DAI master mode support for
SSI on i.MX series") added the divisor calculation which relies on
the clk_round_rate(). However, at that time, clk_round_rate() didn't
provide closest clock rates for some cases because it might not use
a correct rounding policy. So using the original formula (pm + 1) for
PM divisor was not able to give us a desired clock rate. And then we
used (pm + 2) to do the trick.
However, the clk-divider driver has been refined a lot since commit
b11d282dbe ("clk: divider: fix rate calculation for fractional rates")
Now using (pm + 2) trick would result an incorrect clock rate.
So this patch fixes the problem by removing the useless trick.
Reported-by: Stephane Cerveau <scerveau@voxtok.com>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_property_read_u32_array returns 0 on success,
so the return value shouldn't be inverted twice,
first on assignment then in condition expression.
Signed-off-by: Maciej Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The jacks are card level elements so use snd_soc_card_jack_new() instead of
snd_soc_jack_new() to register them.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds snd_soc_of_parse_audio_routing() to get dapm routes
configurations via Device Tree.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to i.MX Reference Manual, the bit-clock frequency generated
by SSI must be never greater than 1/5 of the peripheral clock frequency.
This peripheral clock, however, is not baudclk but the IPG clock (i.e.
ssi_private->clk in the fsl_ssi driver).
So this patch just simply fixes the incorrect limitation applied to
the bit clock (baudclk) rate.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the fsl DAI drivers uses the same semantics as the rest of a ASoC
the custom fsl_asoc_xlate_tdm_slot_mask() callback can be removed as it is
identical to the generic one.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The fsl-ssi and imx-ssi drivers use inverted semantics for the tx_mask and
rx_mask parameter of the set_tdm_slot() callback compared to rest of ASoC.
This patch updates the driver's semantics to be consistent with the rest of
ASoC, i.e. a set bit means a active slot and a cleared bit means a inactive
slot. This will allow us to use the set_tdm_slot() API in a more generic
way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mc13783 driver uses inverted semantics for the tx_mask and rx_mask
parameter of the set_tdm_slot() callback compared to rest of ASoC. This
patch updates the driver's semantics to be consistent with the rest of ASoC,
i.e. a set bit means a active slot and a cleared bit means a inactive slot.
This will allow us to use the set_tdm_slot() API in a more generic way.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the card owner field to avoid getting a kernel crash when the imx-spdif
is unloaded while the playback is active.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 2ffa531078 ("ASoC: fsl_ssi: Fix module unbound") the irq
number is retrieved via platform_get_irq(), which may fail and return a negative
number, so adapt its type to 'int'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The following crash happens when trying to unload the snd_soc_imx_wm8962 module
while playback is active:
[ 208.666868] Unable to handle kernel paging request at virtc
[ 208.674110] pgd = 80004000
[ 208.676867] [7f06541c] *pgd=4c334811, *pte=00000000, *ppte=00000000
[ 208.683211] Internal error: Oops: 80000007 [#1] SMP ARM
[ 208.688445] Modules linked in: snd_soc_wm8962 snd_soc_fsl_ssi snd_soc_imx_audmux imx_pcm_fiq evbug]
...
In order to avoid such problem, fill the card owner field as suggested by
Lars-Peter Clausen:
"But looking at the source it seems that this is a core feature of ALSA and at
least for the card module itself it will do the ref-counting when a stream is
started/stopped. And we even support setting the owner of a card in ASoC.
It's just that pretty much no ASoC card driver bothers to set the owner field
in the snd_soc_card struct. So this particular problem can be fixed by updating
the imx-wm8962 driver to set the owner field."
By doing as suggested, we no longer see the crash when attempting to unload the
snd_soc_imx_wm8962 module while playback is active:
$ modprobe -r snd_soc_imx_wm8962
modprobe: can't unload module snd_soc_imx_wm8962: Resource temporarily
unavailable
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log that contains the full path of the node.
We can have a concise log by using pdev->name instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the error message uses 'np->full_name' which leads to a very verbose
log as:
fsl-ssi-dai 202c000.ssi: no irq for node /soc/aips-bus@02000000/spba-bus@02000000/ssi@0202c000
We can have a concise log by using pdev->name instead:
fsl-ssi-dai 202c000.ssi: no irq for node 202c000.ssi
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 2ffa531078 ("ASoC: fsl_ssi: Fix module unbound") changed the way to
retrieve the irq number from irq_of_parse_and_map() to platform_get_irq(), but
missed to updated the irq error check accordingly.
We should test for negative irq number and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the dai_fmt field in the dai_link struct instead of manually calling
snd_soc_dai_fmt(). This makes the code cleaner and shorter.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The xDC field should have 5 bit width according to Reference Manual.
Thus this patch fixes it.
Signed-off-by: Aurelien BOUIN <a_bouin@yahoo.fr>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The 'name' array is currently stored inside the fsl_asrc private structure only
for registering the interrupt name.
This can be simplified by registering it with dev_name() instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'name' array is currently stored inside the fsl_spdif_priv private structure
only for registering the interrupt name.
This can be simplified by registering it with dev_name() instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under sound/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Acked-by: Mark Brown <broonie@kernel.org>
Lots and lots of changes this time around, the usual set of driver
updates and a huge bulk of cleanups from Lars-Peter. Probably the most
interesting thing for most users is the Intel driver updates which will
(with some more machine integration work) enable support for newer x86
laptops.
- Conversion of AC'97 drivers to use regmap, bringing us closer to the
removal of the ASoC level I/O code.
- Clean up a lot of old drivers that were open coding things that have
subsequently been implemented in the core.
- Some DAPM performance improvements.
- Removal of the now seldom used CODEC mutex.
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers.
- Support for Samsung boards using rt5631 as the CODEC.
- Removal of the obsolete AFEB9260 machine driver.
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUhajpAAoJECTWi3JdVIfQcOsH/00TMeXlkIjnYe+AC9VjEMYN
IAYaXs1UcAfxB4CpS9ik4sb4LQnnxl9aqy5clUZOLHvDAgHmi6L1E8CteJUGFXZ6
/jjpu9/mI975asgyiNP44QDLSNDjzXX6Z1eeXRGvyKMNZkpg4FLfVq9a6ONtf1dw
N3Hl3LG+wvPhAdR/OSKg9eDVnV1iY7mWOWr/9/1q8UhYRpCTL8x70ytBz6tfeU2r
4fQmFma+qefYXvyuqzuiwzSHJKt+46Z35EyNlkCBpVJVErZL2TGOv4H04PjZhg6+
4CR+YGJMSURRhgMCvUCAh4j6a4c+oSXU/LEl9wMcjWMfa3UtZWKojqlK8lYMeoE=
=Pv8r
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.19
Lots and lots of changes this time around, the usual set of driver
updates and a huge bulk of cleanups from Lars-Peter. Probably the most
interesting thing for most users is the Intel driver updates which will
(with some more machine integration work) enable support for newer x86
laptops.
- Conversion of AC'97 drivers to use regmap, bringing us closer to the
removal of the ASoC level I/O code.
- Clean up a lot of old drivers that were open coding things that have
subsequently been implemented in the core.
- Some DAPM performance improvements.
- Removal of the now seldom used CODEC mutex.
- Lots of updates for the newer Intel SoC support, including support
for the DSP and some Cherrytrail and Braswell machine drivers.
- Support for Samsung boards using rt5631 as the CODEC.
- Removal of the obsolete AFEB9260 machine driver.
- Driver support for the TI TS3A227E headset driver used in some
Chrombeooks.
SSI component isn't unregistered if fsl_ssi_debugfs_create() fails
in probe phase.
To fix it, this commit replaces label error_asoc_register with
error_irq.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trying to remove the snd-soc-fsl-ssi module leads to the following warning:
[ 31.515336] ------------[ cut here ]------------
[ 31.520091] WARNING: CPU: 2 PID: 434 at fs/proc/generic.c:521 remove_proc_entry+0x14c/0x16c()
[ 31.528708] remove_proc_entry: removing non-empty directory 'irq/79', leaking at least '202c000.ss'
[ 31.537911] Modules linked in: snd_soc_wm8962 snd_soc_imx_wm8962 snd_soc_fsl_ssi(-) evbug
[ 31.546249] CPU: 2 PID: 434 Comm: rmmod Not tainted 3.18.0-rc6-00028-g3314bf6-dirty #1
[ 31.554235] Backtrace:
[ 31.556816] [<80011ea8>] (dump_backtrace) from [<80012044>] (show_stack+0x18/0x1c)
[ 31.564416] r6:80142c88 r5:00000000 r4:00000000 r3:00000000
[ 31.570267] [<8001202c>] (show_stack) from [<806980ec>] (dump_stack+0x88/0xa4)
[ 31.577588] [<80698064>] (dump_stack) from [<80029d78>] (warn_slowpath_common+0x70/0x94)
[ 31.585711] r5:00000009 r4:bb61fd90
[ 31.589423] [<80029d08>] (warn_slowpath_common) from [<80029e40>] (warn_slowpath_fmt+0x38/0x40)
[ 31.598187] r8:bb61fdfe r7:be05d76d r6:be05d9a8 r5:00000002 r4:be05d700
[ 31.605054] [<80029e0c>] (warn_slowpath_fmt) from [<80142c88>] (remove_proc_entry+0x14c/0x16c)
[ 31.613709] r3:806a79c0 r2:808229a0
[ 31.617371] [<80142b3c>] (remove_proc_entry) from [<80070380>] (unregister_irq_proc+0x94/0xb8)
[ 31.625989] r10:00000000 r8:8000ede4 r7:80955f2c r6:0000004f r5:8118e738 r4:be00af00
[ 31.633952] [<800702ec>] (unregister_irq_proc) from [<80069dac>] (free_desc+0x2c/0x64)
[ 31.641898] r6:0000004f r5:80955f38 r4:be00af00
[ 31.646604] [<80069d80>] (free_desc) from [<80069e68>] (irq_free_descs+0x4c/0x8c)
[ 31.654092] r7:00000081 r6:00000001 r5:0000004f r4:00000001
[ 31.659863] [<80069e1c>] (irq_free_descs) from [<8006fc3c>] (irq_dispose_mapping+0x40/0x5c)
[ 31.668247] r6:be17b844 r5:be17b800 r4:0000004f r3:802c5ec0
[ 31.673998] [<8006fbfc>] (irq_dispose_mapping) from [<7f004ea4>] (fsl_ssi_remove+0x58/0x70 [snd_so)
[ 31.683948] r4:bb5bba10 r3:00000001
[ 31.687618] [<7f004e4c>] (fsl_ssi_remove [snd_soc_fsl_ssi]) from [<803720a0>] (platform_drv_remove)
[ 31.697564] r5:7f0064f8 r4:be17b810
[ 31.701195] [<80372080>] (platform_drv_remove) from [<80370494>] (__device_release_driver+0x78/0xc)
[ 31.710361] r5:7f0064f8 r4:be17b810
[ 31.713987] [<8037041c>] (__device_release_driver) from [<80370d20>] (driver_detach+0xbc/0xc0)
[ 31.722631] r5:7f0064f8 r4:be17b810
[ 31.726259] [<80370c64>] (driver_detach) from [<80370304>] (bus_remove_driver+0x54/0x98)
[ 31.734382] r6:00000800 r5:00000000 r4:7f0064f8 r3:bb67f500
[ 31.740149] [<803702b0>] (bus_remove_driver) from [<80371398>] (driver_unregister+0x30/0x50)
[ 31.748617] r4:7f0064f8 r3:bd9f7080
[ 31.752245] [<80371368>] (driver_unregister) from [<80371f3c>] (platform_driver_unregister+0x14/0x)
[ 31.761498] r4:7f00655c r3:7f005a70
[ 31.765130] [<80371f28>] (platform_driver_unregister) from [<7f005a84>] (fsl_ssi_driver_exit+0x14/)
[ 31.776147] [<7f005a70>] (fsl_ssi_driver_exit [snd_soc_fsl_ssi]) from [<8008ed80>] (SyS_delete_mod)
[ 31.786553] [<8008ec64>] (SyS_delete_module) from [<8000ec20>] (ret_fast_syscall+0x0/0x48)
[ 31.794824] r6:00c46d18 r5:00000800 r4:00c46d18
[ 31.799530] ---[ end trace 954e8a3a15379e52 ]---
The cause of problem and solution are well explained by Lars-Peter:
"The driver creates the mapping by calling irq_of_parse_and_map(), so it also
has to dispose the mapping. But the easy way out is to simply use
platform_get_irq() instead of irq_of_parse_map(). In this case the mapping is
not managed by the device but by the of core, so the device has not to dispose
the mapping."
Tested on a imx6q-sabresd board.
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ESAI may need to use fixed slot width to comply with external
CODEC. So this set_tdm_slot() call will allow the ESAI driver
to override its default dynamic slot width policy.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver previously used 32-bit fixed slot width as default.
In result, ESAI might use 32-bit length to capture 16-bit width
audio slot from CODEC side when ESAI is running as DAI slave.
So this patch just removes the default slot_width so as to use
dynamic slot width. If there comes a specific situation that
needs a fixed width, the machine driver shall set slot_width
via set_tdm_slot() so as to let the ESAI driver replace the
dynamic width policy with the fixed value.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Setting the ac97_control field on a CPU DAI tells the ASoC core that this
DAI in addition to audio data also transports control data to the CODEC.
This causes the core to suspend the DAI after the CODEC and resume it before
the CODEC so communication to the CODEC is still possible. This is not
necessarily something that is specific to AC'97 and can be used by other
buses with the same requirement. This patch renames the flag from
ac97_control to bus_control to make this explicit.
While we are at it also change the type from int to bool.
The following semantich patch was used for automatic conversion of the
drivers:
// <smpl>
@@
identifier drv;
@@
struct snd_soc_dai_driver drv = {
- .ac97_control
+ .bus_control
=
- 1
+ true
};
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mpc5200_dma overwrites the private_data field of the CODEC's AC'97
device with the DMA drivers private data, but never actually reads it again.
Given that the private_data field is supposed to be owned by the AC'97
driver, overwriting it may cause undefined behavior. This patch removes the
code that overwrites the field from the driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The mpc5200_psc_ac97 driver puts a snd_ac97 device on the stack in the
driver probe function, initializes the private data member of the device and
the never uses the device again. It should be safe to remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current driver can also run in I2S master mode, so remove the old comment.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new helper function snd_pcm_stop_xrun() to the standard sequnce
lock/snd_pcm_stop(XRUN)/unlock by a single call, and replace the
existing open codes with this helper.
The function checks the PCM running state to prevent setting the wrong
state, too, for more safety.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When cpu-dai is the DAI Master (CBM_CFx), it may need some configurations,
set_sysclk() call for eample, for cpu-dai side in the hw_params(), even if
the set_bias_level() has already taken care of the codec-dai side.
So this patch just simply adds an additional condition.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kernel dump (WARN_ON) ocurred during system boot-up inside regmap_write():
------------[ cut here ]------------
WARNING: CPU: 0 PID: 47 at kernel/locking/lockdep.c:2744 lockdep_trace_alloc+0xe8/0x108()
DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags))
Modules linked in:
CPU: 0 PID: 47 Comm: kworker/u2:2 Not tainted 3.18.0-rc1-10245-gb75d289-dirty #56
Workqueue: deferwq deferred_probe_work_func
Backtrace:
[<80012294>] (dump_backtrace) from [<80012578>] (show_stack+0x18/0x1c)
r6:8097c73c r5:8097c73c r4:00000000 r3:be33ba80
[<80012560>] (show_stack) from [<806aac48>] (dump_stack+0x8c/0xa4)
[<806aabbc>] (dump_stack) from [<8002a694>] (warn_slowpath_common+0x70/0x94)
r6:80062838 r5:00000009 r4:bd827b30 r3:be33ba80
[<8002a624>] (warn_slowpath_common) from [<8002a6f0>] (warn_slowpath_fmt+0x38/0x40)
r8:00000004 r7:00000001 r6:000080d0 r5:60000193 r4:bd826010
[<8002a6bc>] (warn_slowpath_fmt) from [<80062838>] (lockdep_trace_alloc+0xe8/0x108)
r3:80831590 r2:8082e160
[<80062750>] (lockdep_trace_alloc) from [<800ea5dc>] (kmem_cache_alloc+0x28/0x134)
r5:000080d0 r4:be001f00
[<800ea5b4>] (kmem_cache_alloc) from [<8038d72c>] (regcache_rbtree_write+0x15c/0x648)
r10:00000000 r9:0000001c r8:00000004 r7:00000001 r6:00000000 r5:bd819a00
r4:00000000 r3:811aea88
[<8038d5d0>] (regcache_rbtree_write) from [<8038c4d8>] (regcache_write+0x5c/0x64)
r10:be3f9f88 r9:00000000 r8:00000004 r7:00000001 r6:00000000 r5:00000001
r4:bd819a00
[<8038c47c>] (regcache_write) from [<8038b0dc>] (_regmap_raw_write+0x134/0x5f4)
r6:be3f9f84 r5:00000001 r4:bd819a00 r3:00000001
[<8038afa8>] (_regmap_raw_write) from [<8038b610>] (_regmap_bus_raw_write+0x74/0x94)
r10:00000000 r9:00000001 r8:be3fb080 r7:bd819a00 r6:00000001 r5:00000000
r4:bd819a00
[<8038b59c>] (_regmap_bus_raw_write) from [<8038a8b4>] (_regmap_write+0x60/0x9c)
r6:00000001 r5:00000000 r4:bd819a00 r3:8038b59c
[<8038a854>] (_regmap_write) from [<8038ba24>] (regmap_write+0x48/0x68)
r7:bd81ad80 r6:00000001 r5:00000000 r4:bd819a00
[<8038b9dc>] (regmap_write) from [<80528f30>] (fsl_asrc_dai_probe+0x34/0x104)
r6:bd888628 r5:be3fb080 r4:be3b4410 r3:be3b442c
------------[ dump end ]------------
=============================================================================
2741 /*
2742 * Oi! Can't be having __GFP_FS allocations with IRQs disabled.
2743 */
2744 if (DEBUG_LOCKS_WARN_ON(irqs_disabled_flags(flags)))
2745 return;
=============================================================================
By looking at 2744 line, we can get that it's because regcache_rbtree_write()
would call kmalloc() with GFP flag if it couldn't find an existing block to
insert nodes while this kmalloc() call is inside a spin_lock_irq_save pair,
i.e. IRQs disabled.
Even though this may be a bug that should be fixed, I still try to send this
patch as a quick fix (work around) since it does no harm to assign default
values of every registers when using regcache.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use strncpy() instead of strcpy(). That's not a security issue, as the
source buffer is taken from DT nodes, but we should still enforce bound
checks. Spotted by Coverity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The of_node_put() call in eukrea_tlv320_probe() may take an
uninitialized pointer, as compiler spotted out:
sound/soc/fsl/eukrea-tlv320.c:221:14: warning: 'ssi_np' may be used uninitialized in this function [-Wuninitialized]
This patch adds the proper NULL initializations as a fix.
(codec_np is also NULL initialized just for consistency.)
Fixes: 66f232908d ('ASoC: eukrea-tlv320: Add DT support')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_node_put() supports NULL as its argument, so the initial test is not
necessary.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_node_put() supports NULL as its argument, so the initial test is not
necessary.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_node_put() supports NULL as its argument, so the initial test is not
necessary.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_node_put() supports NULL as its argument, so the initial test is not
necessary.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The of_node_put() calls in imx_es8328_probe() may take uninitialized
pointers when reached though the early error path. This patch adds
the proper NULL initialization for fixing these.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
An error code was forgotten to be passed in the error path of
imx_es8328_probe().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wm8962 driver uses the input subsystem, but it is selected by
SND_SOC_FSL_ASOC_CARD, which can be built with CONFIG_INPUT disabled,
resulting in this link error:
ERROR: "input_event" [sound/soc/codecs/snd-soc-wm8962.ko] undefined!
ERROR: "input_register_device" [sound/soc/codecs/snd-soc-wm8962.ko] undefined!
ERROR: "devm_input_allocate_device" [sound/soc/codecs/snd-soc-wm8962.ko] undefined!
Do not force the selection of the codecs by SND_SOC_FSL_ASOC_CARD to avoid
such problem.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to use 'i2s-slave' property, since master/slave configuration
are passed via machine layer.
This change does not break existing users because they do check for slave
mode inside sound/soc/fsl/mpc8610_hpcd.c/p1022_ds.c/p1022_rdk.c
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
code can raise a panic when the ssi_private->pdev is null
[...]
/*
* If codec-handle property is missing from SSI node, we assume
* that the machine driver uses new binding which does not require
* SSI driver to trigger machine driver's probe.
*/
if (!of_get_property(np, "codec-handle", NULL))
goto done;
[...]
ssi_private->pdev =
platform_device_register_data(&pdev->dev, name, 0, NULL, 0);
[...]
done:
if (ssi_private->dai_fmt)
_fsl_ssi_set_dai_fmt(ssi_private, ssi_private->dai_fmt);
Proposal was to not use ssi_private->pdev->dev here but adding a new parameter
of *dev pointer to this _set_dai_fmt() -- passing pdev->dev in probe() and
cpu_dai->dev in fsl_ssi_set_dai_fmt().
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reported-by: Jean-Michel Hautbois <jean-michel.hautbois@vodalys.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check if ipg clock is in clock-names property, then we can move the
ipg clock enable and disable operation to startup and shutdown, that
is only enable ipg clock when ssi is working and keep clock is disabled
when ssi is in idle.
But when the checking is failed, remain the clock control as before.
Tested-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'big-endian-data' property is originally used to indicate whether the
LSB firstly or MSB firstly will be transmitted to the CODEC or received
from the CODEC, and there has nothing relation to the memory data.
Generally, if the audio data in big endian format, which will be using the
bytes reversion, Here this can only be used to bits reversion.
So using the 'lsb-first' instead of 'big-endian-data' can make the code
to be readable easier and more easy to understand what this property is
used to do.
This property used for configuring whether the LSB or the MSB is transmitted
first for the fifo data.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Build kernel with SND_SOC_FSL_ASOC_CARD=m && SND_SOC_FSL_{SSI,SAI,ESAI}=y
leads the following error:
sound/built-in.o: In function `fsl_sai_probe':
>> fsl_sai.c:(.text+0x5f662): undefined reference to `imx_pcm_dma_init'
sound/built-in.o: In function `fsl_esai_probe':
>> fsl_esai.c:(.text+0x6044b): undefined reference to `imx_pcm_dma_init'
The config SND_SOC_FSL_ASOC_CARD is for IMX SOC, So move it under condition
of 'if SND_IMX_SOC'.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The imx-es8328 driver fails to build on PPC because it explicitly depends on
SND_SOC_IMX_PCM_FIQ, which itself doesn't build on PPC. Instead, rely on
the SND_SOC_FSL_SSI config option to pull in the necessary libraries.
While we're at it, remove SND_SOC_FSL_UTILS, which also is not needed.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Building kernel with SND_SOC_IMX_AUDMUX=n leads to the following error:
sound/built-in.o: In function `fsl_asoc_card_probe':
>> fsl-asoc-card.c:(.text+0x1467b5): undefined reference to `imx_audmux_v2_configure_port'
>> fsl-asoc-card.c:(.text+0x1467d0): undefined reference to `imx_audmux_v2_configure_port'
>> fsl-asoc-card.c:(.text+0x1467ed): undefined reference to `imx_audmux_v2_configure_port'
>> fsl-asoc-card.c:(.text+0x146807): undefined reference to `imx_audmux_v2_configure_port'
Update Kconfig to select SND_SOC_IMX_AUDMUX when SND_SOC_FSL_ASOC_CARD=y.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is one design rule according to SAI's reference manual:
If the transmitter bit clock and frame sync are to be used by both transmitter
and receiver, the transmitter must be configured for asynchronous operation
and the receiver for synchronous operation.
And SYNC of TCR2 is a 2-width control bit:
00 Asynchronous mode.
01 Synchronous with receiver.
10 Synchronous with another SAI transmitter.
11 Synchronous with another SAI receiver.
So the driver should have set SYNC bit of TCR2 to 0x0, and meanwhile set SYNC
bit of RCR2 to 0x1 (Synchronous with transmitter).
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This adds an initial machine driver for the ES8328 audio codec on Freescale
boards. The driver supports headphones and an audio regulator for an onboard
speaker amp.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The previous patch (ASoC: fsl_sai: Add asynchronous mode support) added
new Device Tree bindings for Asynchronous and Synchronous modes support.
However, these two shall not be present at the same time.
So this patch just simply makes them exclusive so as to avoid incorrect
Device Tree binding usage.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SAI supports these operation modes:
1) asynchronous mode
Both Tx and Rx are set to be asynchronous.
2) synchronous mode (Rx sync with Tx)
Tx is set to be asynchronous, Rx is set to be synchronous.
3) synchronous mode (Tx sync with Rx)
Rx is set to be asynchronous, Tx is set to be synchronous.
4) synchronous mode (Tx/Rx sync with another SAI's Tx)
5) synchronous mode (Tx/Rx sync with another SAI's Rx)
* 4) and 5) are beyond this patch because they are related with another SAI.
As the initial version of this SAI driver, it supported 2) as default while
the others were totally missing.
So this patch just adds supports for 1) and 3).
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is one design rule according to SAI's reference manual:
If the transmitter bit clock and frame sync are to be used by both transmitter
and receiver, the transmitter must be configured for asynchronous operation
and the receiver for synchronous operation.
And SYNC of TCR2 is a 2-width control bit:
00 Asynchronous mode.
01 Synchronous with receiver.
10 Synchronous with another SAI transmitter.
11 Synchronous with another SAI receiver.
So the driver should have set SYNC bit of TCR2 to 0x0, and meanwhile set SYNC
bit of RCR2 to 0x1 (Synchronous with transmitter).
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds software reset code in dai_probe() so as to make a true init
by clearing SAI's internal logic, including the bit clock generation, status
flags, and FIFO pointers.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Original driver didn't store the number of slots, just fix the slot number
to 2, use this default number to calculate bclk and pins for TX/RX.
In this patch, add one parameter for slots, and update the calculation of
bclk and pins of TX/RX. Then driver will be compatible with slots > 2 in
TDM mode.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Freescale Generic ASoC Sound Card is a general ASoC DAI Link driver that
can be used, ideally, for all Freescale CPU DAI drivers and external CODECs.
The idea of this generic sound card is a bit like ASoC Simple Card. However,
for Freescale SoCs (especially those released in recent years), most of them
have ASRC (Documentation/devicetree/bindings/sound/fsl,asrc.txt) inside. And
this is a specific feature that might be painstakingly controlled and merged
into the Simple Card driver.
So having this driver will allow all Freescale SoC users to benefit from the
simplification to support a new card and the capability of wide sample rates
support through ASRC.
The driver is initially designed for sound card using I2S or PCM DAI formats.
However, it's also possible to merge those non-I2S/PCM type sound cards, such
as S/PDIF audio and HDMI audio, into this card as long as the merge will not
break the original function and as long as there is something redundant that
can be abstracted along with I2S type sound cards.
As an initial version, it only supports three cards that I can test:
imx-audio-cs42888, a new card that links ESAI with CS42888 CODEC
imx-audio-sgtl5000, just like the old imx-sgtl5000.c driver
imx-audio-wm8962, just like the old imx-wm8962.c driver
The driver is also compatible with the old Device Tree bindings of WM8962 and
SGTL5000. So we may consider to remove those two drivers after this driver is
totally enabled. (It needs to be added into defconfig)
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Original driver didn't store the number of slots, just fix the slot number
to 2, use this default number to calculate bclk and pins for TX/RX.
In this patch, add one parameter for slots, and update the calculation of
bclk and pins of TX/RX. Then driver will be compatible with slots > 2 in
TDM mode.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit a603c8ee52.
fsl_asoc_xlate_tdm_slot_mask() is different with snd_soc_xlate_tdm_slot_mask().
fsl_asoc_xlate_tdm_slot_mask() will set the enabled bit to 0, disabled bit
to 1. snd_soc_xlate_tdm_slot_mask() will set the enabled bit to 1, disabled
bit to 0.
For esai when the bit value is 1, the slot is enabled, when the bit value is 0,
the slot is disabled. If using fsl_asoc_xlate_tdm_slot_mask(), the esai will
work abnormally. So revert this patch, make the esai use default function.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add SND_SOC_DAIFMT_CBM_CFS support for Freescale architecture.
Successfully tested on i.MX 6Quad Wandboard and UDOO boards connected to
the pcm1792a codec.
In CBM_CFS mode, when using a sample size of 16 bits, we cannot use
CCSR_SSI_SCR_I2S_MODE_MASTER since we get a frame sync every 16 bits.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Fabio Falzoi <fabio.falzoi84@gmail.com>
Tested-by: Angelo Adamo <adamo.a60@gmail.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since we pass the port number through file private data for debugfs we cast
it to and from a pointer so use uintptr_t in order to ensure that the
types are compatible, avoiding warnings on 64 bit platforms where pointers
are 64 bit and unsigned integers 32 bit.
Signed-off-by: Mark Brown <broonie@linaro.org>
The patch 3117bb3109: "ASoC: fsl_asrc: Add ASRC ASoC CPU DAI and
platform drivers" from Jul 29, 2014, leads to the following Smatch
complaint:
sound/soc/fsl/fsl_asrc_dma.c:304 fsl_asrc_dma_shutdown()
warn: variable dereferenced before check 'pair' (see line 302)
sound/soc/fsl/fsl_asrc_dma.c
301 struct fsl_asrc_pair *pair = runtime->private_data;
302 struct fsl_asrc *asrc_priv = pair->asrc_priv;
^^^^^^^^^^^^^^^
Dereference.
303
304 if (pair && asrc_priv->pair[pair->index] == pair)
^^^^
Check.
305 asrc_priv->pair[pair->index] = NULL;
306
So we just let the driver check pair before using it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DPCM needs extra dapm routes in the machine driver to route audio
between Front-End and Back-End. In order to differ the stream names
in the route map from CODECs, we here add specific stream names to
SSI driver so that we can implement ASRC via DPCM to it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
DPCM needs extra dapm routes in the machine driver to route audio
between Front-End and Back-End. In order to differ the stream names
in the route map from CODECs, we here add specific stream names to
SPDIF driver so that we can implement ASRC via DPCM to it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DPCM needs extra dapm routes in the machine driver to route audio
between Front-End and Back-End. In order to differ the stream names
in the route map from CODECs, we here add specific stream names to
SAI driver so that we can implement ASRC via DPCM to it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
DPCM needs extra dapm routes in the machine driver to route audio
between Front-End and Back-End. In order to differ the stream names
in the route map from CODECs, we here add specific stream names to
ESAI driver so that we can implement ASRC via DPCM to it.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a cut and paste bug so it returns success instead of the error
code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Building a kernel with SND_SOC_GENERIC_DMAENGINE_PCM=n leads to the following
error:
ERROR: "snd_dmaengine_pcm_prepare_slave_config" [sound/soc/fsl/snd-soc-fsl-asrc.ko] undefined!
Let SND_SOC_FSL_ASRC select SND_SOC_GENERIC_DMAENGINE_PCM in order to fix such
error.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following build errors that were observed by building with
make ARCH=microblaze allyesconfig:
>> sound/soc/fsl/fsl_asrc.c:906:5: warning: "CONFIG_PM_RUNTIME" is not defined [-Wundef]
#if CONFIG_PM_RUNTIME
^
>> sound/soc/fsl/fsl_asrc.c:934:5: warning: "CONFIG_PM_SLEEP" is not defined [-Wundef]
#if CONFIG_PM_SLEEP
^
>> sound/soc/fsl/fsl_asrc.c:906:5: warning: "CONFIG_PM_RUNTIME" is not defined [-Wundef]
#if CONFIG_PM_RUNTIME
^
>> sound/soc/fsl/fsl_asrc.c:934:5: warning: "CONFIG_PM_SLEEP" is not defined [-Wundef]
#if CONFIG_PM_SLEEP
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Asynchronous Sample Rate Converter (ASRC) converts the sampling rate of a
signal associated with an input clock into a signal associated with a different
output clock. The driver currently works as a Front End of DPCM with other Back
Ends DAI links such as ESAI<->CS42888 and SSI<->WM8962 and SAI. It converts the
original sample rate to a common rate supported by Back Ends for playback while
converts the common rate of Back Ends to a desired rate for capture. It has 3
pairs to support three different substreams within totally 10 channels.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The previous enable flow:
1, Enable TE&RE (SAI starts to consume tx FIFO and feed rx FIFO)
2, Mask IRQ of Tx/Rx to enable its interrupt.
3, Enable DMA request of Tx/Rx.
As this flow would enable DMA request later than TERE, the Tx FIFO
would be easily emptied into underrun while Rx FIFO would be easily
stuffed into overrun due to the delayed DMA transfering.
This issue happened merely occational before the patch 'ASoC: fsl_sai:
Reset FIFOs after disabling TE/RE' because there were useless data
remaining in the FIFO for the gap. However, it manifested after FIFO
reset's implemented.
After this patch, the new flow:
1, Enable DMA request of Tx/Rx.
2, Enable TE&RE (SAI starts to consume tx FIFO and feed rx FIFO)
3, Mask IRQ of Tx/Rx to enable its interrupt.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
TE/RE bit of T/RCSR will remain set untill the current frame is physically
finished. The FIFO reset operation should wait this bit's totally cleared
rather than ignoring its status which might cause TE/RE disabling failed.
This patch adds delay and timeout to wait for its completion before FIFO
reset.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For trigger start, we don't need to check if it's the first time to
enable TE/RE or second time. It doesn't hurt to enable them any way,
which in the meantime can reduce race condition for TE/RE enabling.
For trigger stop, we will definitely clear FRDE of current direction.
Thus the driver only needs to read the opposite one's.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Quite a few build coverage fixes in here among the usual small driver
fixes includling the sigmadsp change from Lars - moving the driver to
separate modules per bus (which is basically just code motion) avoids
issues with some combinations of buses being enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O7yF
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.16-rc1' into asoc-linus
ASoC: Fixes for v3.16
Quite a few build coverage fixes in here among the usual small driver
fixes includling the sigmadsp change from Lars - moving the driver to
separate modules per bus (which is basically just code motion) avoids
issues with some combinations of buses being enabled.
# gpg: Signature made Thu 19 Jun 2014 11:57:31 BST using RSA key ID 7EA229BD
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>"
# gpg: aka "Mark Brown <broonie@debian.org>"
# gpg: aka "Mark Brown <broonie@kernel.org>"
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>"
# gpg: aka "Mark Brown <broonie@linaro.org>"
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>"
In the rx irq handling part, we should clear the flags in RCSR not TCSR.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SAI will not clear their FIFOs after disabling TE/RE. Therfore, the driver
should take care the task so as not to let useless data remain in the FIFO.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I received a report this morning from one of the Novena developers that
the behaviour of the iMX6 ASoC codec driver (using imx-pcm-dma.c) was
sub-optimal under high system load.
While there are issues relating to system load remaining, upon reviewing
the ASoC imx-pcm-dma.c driver, it was noticed that it not using the
residue support, because SDMA doesn't support it. This has the effect
that SDMA has to make multiple calls into the ASoC and ALSA code, one
for each period.
Since ALSA's snd_pcm_elapsed() does not need to be called multiple times
and it is entirely sufficient to call it once to update ALSA with the
current buffer position via the pointer method, we can do better here.
We can also avoid stopping the DMA entirely, just like real cyclic DMA
implementations behave. While this means that we replay some old samples,
this is a nicer behaviour than having audio stop and restart.
The changes to achieve this are relatively minor - imx-sdma.c can track
where the DMA is to the nearest descriptor boundary - it does this
already when deciding how many callbacks to issue. In doing this,
buf_tail always points at the descriptor which will complete next.
The residue is defined by the bytes remaining to the end of the buffer,
when the buffer is viewed as a single block of memory [start...end].
So, when we start out, there's a full buffer worth of residue, and this
counts down as we approach the end of the buffer, eventually becoming
zero at the end, before returning to the full buffer worth when we
wrap back to the start.
Moving the walking of the descriptors into the interrupt handler means
that we can update the BD_DONE flag at interrupt time, thus avoiding
a delayed tasklet stopping the cyclic DMA.
This means that the residue can be calculated from (total descriptors -
buf_tail) * descriptor size. This is what the change below does. We
update imx-pcm-dma.c to remove the NO_RESIDUE flag since we now provide
the residue.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Commit 31ee2bfd72 ("ASoC: fsl: select SND_SOC_IMX_PCM_DMA
where needed") started selecting SND_SOC_IMX_PCM_DMA and
SND_SOC_IMX_PCM_FIQ for two drivers when building for i.MX.
This has turned out too aggressive, as FIQ is only available
for i.mx2 through i.mx5, but not i.mx6 or vybrid.
Further, two more drivers have become user-selectable in the
meantime, and they both depend on DMA for the imx platform
as well.
This changes the selection of FIQ to depend on the TZIC or
AVIC interrupt controllers that actually export the imx
specific FIQ interfaces, and adds the missing select statements
for SAI and ESAI.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
do_div() requires that the first parameter is a 64-bit integer,
which but clkrate was defined as an unsigned long. This caused
the following warnings:
CC sound/soc/fsl/fsl_ssi.o
sound/soc/fsl/fsl_ssi.c: In function 'fsl_ssi_set_bclk':
sound/soc/fsl/fsl_ssi.c:593:3: warning: comparison of distinct pointer types lacks a cast
sound/soc/fsl/fsl_ssi.c:593:3: warning: right shift count >= width of type
sound/soc/fsl/fsl_ssi.c:593:3: warning: passing argument 1 of '__div64_32' from incompatible pointer type
include/asm-generic/div64.h:35:17: note: expected 'uint64_t *' but argument is of type 'long unsigned int *'
Signed-off-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for the output sample rates 96kHz and 192kHz.
Tested with a Cubox-i imx6 system and an Onkyo TX-SR607 receiver.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
1) Apply better indentations
2) Drop braces for single statement.
3) Use simpler ternary to reduce code.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 432481220 (ASoC: fsl-ssi: Use regmap) removed struct ccsr_ssi.
Unfortunately, the structure is still used. This causes
mpc85xx_smp_defconfig and mpc85xx_defconfig builds to fail with
sound/soc/fsl/fsl_dma.c:926:50:
error: invalid use of undefined type 'struct ccsr_ssi'
dma->ssi_stx_phys = res.start + offsetof(struct ccsr_ssi, stx0);
ound/soc/fsl/fsl_dma.c:927:50:
error: invalid use of undefined type 'struct ccsr_ssi'
dma->ssi_srx_phys = res.start + offsetof(struct ccsr_ssi, srx0);
Fix by using constants, similar to original commit.
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
The calculation code does
u64 = (u32 - u32) * 100000;
The 64 bits are of no help here as the type is casted only after the
multiplication, and therefore the result may overflow, possibly causing
inoptimal or wrong clock setup in an unfortunate case (the maximum
result value of the first substraction is currently 47999).
Fix the code to cast before multiplication.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We should not copy the return value into this val since it's supposed to
get the value of the register not the success result of regmap_read().
Thus fix it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Eukrea-i.MX51 board was converted to use DT, ie we no longer have a
MACH_EUKREA_MBIMXSD51_BASEBOARD symbol.
Transformation of other boards planned for the near future, so this
patch removes all these dependencies and restricts build of this
driver to ARCH_MXC.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch replaces the ssi specific functions write_ssi, read_ssi and
write_ssi_mask by standard regmap function calls.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Reorder all variables in struct fsl_ssi_private to have groups that make
sense together. The patch also updates the struct documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The baudclock may be used and set by different streams.
Allow only the first stream to set the bitclock rate. Other streams have
to try to get to the correct rate without modifying the bitclock rate
using the SSI internal clock modifiers.
The variable baudclk_streams is introduced to keep track of the active
streams that are using the baudclock. This way we know if the baudclock
may be set and whether we may enable/disable the clock.
baudclock enable/disable is moved to hw_params()/hw_free(). This way we can
keep track of the baudclock in those two functions and avoid a running
clock while it is not used. As hw_params()/hw_free() may be called
multiple times for the same stream, we have to use baudclk_streams
variable to know whether we may enable/disable the clock.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
In i2s master mode the fsl_ssi driver depends on someone calling
.set_tdm_slot correctly. In this mode though only a DC value of
2 is allowed, so set it in this case and no longer depend on
.set_tdm_slot.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The baudclock_locked variable is only used in functions which
are serialized anyway from the core. No need to have a lock
around the variable, so remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The fsl_ssi driver uses the .set_sysclk callback to configure the
bitclock for master mode. This is unnecessary since the bitclock
is known in hw_params. This patch configures the bitclock from .hw_params.
.set_dai_sysclk now sets a bitclock frequency which is preferred over
the default calculated bitclock frequency.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The simple soundcard binding has its own way for specifying the dai
format. To be able to use this binding we have to make the fsl,mode
property optional. As the property is used in existing devicetrees
keep the option around for compatibility reasons.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Introduce a SoC data struct which contains the differences between
the different SoCs this driver supports. This makes it easy to support
more differences without having to introduce a new switch/case each
time.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
fsl_ssi_set_dai_sysclk will be called from fsl_ssi_hw_params in the
next patch. Move up to avoid forward declaration and to keep the next patch
more readable. No functional change.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the fsl-ssi unit is used in i2s slave mode, it is possible that the
SSI unit starts transmitting data on the wrong channel. This happens
because the SSI does not synchronize with the left-right-clock by
default.
This patch enables transmit enable synchronization.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
There are some variables defined in struct fsl_ssi_private that describe
states that are also described by other variables.
This patch adds some helper functions that return exactly the same
information based on available variables. This helps to clean up struct
fsl_ssi_private and remove them from the probe function.
It also removes some not really used variables (new_binding, name).
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Reorder the probe function to be able to move the second imx-specific
block to the seperate imx probe function. The patch also removes some
comments/variables/code that are not used anymore or could be simply
replaced by other variables.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify dma DT property handling. fsl,ssi-dma-events is not used
anymore. It passes invalid data to imx_pcm_dma_params_init_data() which
copies some data into an imx dma struct. This struct is never used in
imx-dma or imx-sdma because of generic OF DMA handling. The
"fsl,ssi-dma-events" is not used anywhere in dts files.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move imx specific probe code to a seperate function. It reduces the
size of the probe() function and makes the code and error handling
easier to understand.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instead of creating a name using string manipulation functions, we can
simply use the device name for the DAI driver struct.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move all code that is only used for debugging to a seperate file. This
makes it easier to see what functions are used for debugging only.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The bits we have to clear when disabling are different when the other
stream is still active.
This patch fixes the calculation of new register values after disabling
one stream. It also adds a more detailed description of the new register
value calculation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We don't need to change those dividers if bclk and mclk remains the same
directions and values.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
According to Reference Manual -- ESAI Initialization chapter, as the
standard procedure of ESAI personal reset, the PCRC and PRRC registers
should be remained in its reset value and then configured after T/RCCR
and T/RCR configurations's done but before TE/RE's enabling.
So this patch moves PCRC and PRRC settings to the end of hw_params().
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>