dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/at91-dvk_som60.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f0018000/eeprom@87: I2C bus unit address format error, expected "57"
arch/arm/boot/dts/at91-dvk_som60.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f0018000/ft5426@56: I2C bus unit address format error, expected "38"
arch/arm/boot/dts/at91-vinco.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f8024000/rtc@64: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/at91sam9260ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9g20ek_2mmc.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9g20ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9261ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/tsc2046@0: SPI bus unit address format error, expected "2"
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
As TCB2 doesn't have any output pins, use it for timers
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
vcc_3v3_reg is a fixed regulator and doesn't need a reg property. Remove
its unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix gpio active flag for the phy reset-gpios property. The line is
active low instead of active high.
Actually, this flags was never used by the macb driver.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The Versatile Industrial Communication platform is a community oriented
board from Landis + Gyr. It comes with:
- an RS-485 port
- 2 Ethernet ports
- a wireless M-BUS
- a 4G modem
- a 4MB SPI flash
- a 4GB eMMC
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
