This adds labels to commonly used device-tree nodes so that derivative
boards can avoid ahb/apb hierarchy.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove pullup on uart TX signals, they are push-pull outputs thus
pullups are pointless.
Add pullup on uart RX signals, they prevent the RX signals to be left
floating and so consuming a useless extra amount of power in crowbarred
state if nothing is connected to RX.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add simple-mfd and syscon to the TC blocks to allow to register one of the
channels as clocksource properly at boot time and free up the remaining
channels for other use.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Use the new EBI/NAND bindings to declare NAND chips and remove old NAND
nodes along the way.
Note that we keep using old bindings in at91rm9200.dtsi because this
SoC is not supported by the EBI driver.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Declare new nodes for the EBI and NAND controllers embedded in various
at91/sama5 SoCs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove pullup on dbgu DTXD signal, it is a push-pull output thus the
pullup is pointless.
Add pullup on dbgu DRXD signal, it prevents the DRXD signal to be left
floating and so consuming a useless extra amount of power in crowbarred
state if nothing is externally connected to dbgu.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
i2c-gpio doesn't need a reg property. Change the node names to i2c-gpio-x
as used in other dts to remove the unit-address.
Solves:
Warning (unit_address_vs_reg): Node /i2c@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@2 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Endpoint nodes have a reg property. Add their mandatory unit-address.
This solves:
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep0 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep1 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep2 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep3 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep4 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep5 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep6 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep7 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep8 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep9 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep10 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep11 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep12 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep13 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep14 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep15 has a reg or ranges property, but no unit name
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The triggers don't need a reg property, remove it when prenset. Also remove
the unit-address from their name.
This solves:
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@3 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The memory range assigned to the PMC (Power Management Controller) was
not including the PMC_PCR register which are used to control peripheral
clocks.
This was working fine thanks to the page granularity of ioremap(), but
started to fail when we switched to syscon/regmap, because regmap is
making sure that all accesses are falling into the reserved range.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Fixes: 863a81c3be ("clk: at91: make use of syscon to share PMC registers in several drivers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The PMC is not only used to drive the clocks but also has some registers
related to other functions. One of those is for example the USB gadget
bias.
Using a syscon allows to properly separate those functions.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The watchdog, the reset controller, the RTC, the shutdown controller, the
timer counters and the LCD PWM need the slow clock, add it where necessary,
The LCD PWM will be handled later.
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
at91sam9g45, at91sam9x5 and sama5 SoCs should not use
"atmel,at91sam9rl-udc" for their USB device compatible property since
this compatible is attached to a specific hardware bug fix.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> #4.0+
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The ohci driver now calls clk_set_rate on the uhpck clock (which forwards
set_rate requests to its parent: the usb clock).
Remove useless references to usb clocks from ohci definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The uhpck is useless for High-Speed communications, remove the reference
to this clock in all ehci definitions.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The DBGU is not a simple UART and we need to be able to distinguish it from the
other UARTs, in particular to get its address and check the chip id.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The UTMI clock must be selected by any high-speed USB IP. The logic behind it
needs this particular clock.
So, correct the clock in the device tree files affected.
Reported-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: <stable@vger.kernel.org> #3.18
Since turning on idle-halt in commit fe46aa679f (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: Michel Marti <mma@objectxp.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add nodes for the SRAM available on atmel SoCs
For the at91sam9260 and the at91sam9g20, address mirroring is used to create a
single contiguous SRAM range instead of declaring two separate banks.
Also remove leftover TODOs in the sam9g45 file
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: correct at91sam9rl sram size => 0x10000]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds usart dma definitions to both dtsi for sam9x5 chips. Without
usage of dma it's unable to catch all bytes on usart receiver.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Use the correct compatible string for the ADC of the at91sam9x5 family of SoCs.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This branch gathers a few devicetree patches needed for the reworks found in
the later patches to be sent. More precisely, it holds:
- The addition of ddrck for the sama5d3 and the sam9 SoCs
- The addition of the shutdown controller node in the sama5d3 DTSI
- The slight rework of the ramc bindings for the SoCs that have several RAM
controllers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4QeK
-----END PGP SIGNATURE-----
Merge tag 'at91-dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux
Pull AT91 ramc and reset/poweroff related DT patches from Maxim Ripard:
"This branch gathers a few devicetree patches needed for the reworks found in
the later patches to be sent. More precisely, it holds:
- The addition of ddrck for the sama5d3 and the sam9 SoCs
- The addition of the shutdown controller node in the sama5d3 DTSI
- The slight rework of the ramc bindings for the SoCs that have several RAM
controllers"
Conflicts:
arch/arm/boot/dts/at91sam9g45.dtsi
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTzJFGAAoJEHm+PkMAQRiGNzQH/087gQch5K+A2HKvPzjUXq57
G82DJHLONMMq8+NY3Vqhp8g2V8zRbXGJEvMJMsyuscO37Vo7ADcrYo8lqY9w5bIl
h+Zarhkqz0rqRs2SfMMIVzdd2W7MzL+lqj3GplGPxHztw0+qk7PRKILx6eRppGaH
JaD4NfkD5+1vfve/2d1ze9D5pCiw6PFNzjesKZxScQhNhIyLdRamfSTY4r9XeURo
CxpwjphEYfvAcgc39mwzEHPHyKSqULu0By6R8FXQpJ9QjVtzcGEiF+cPqGncpZOR
5ZSyU5e1CpBl9w8o6Lm9ewXmaCSnBU/VFrOwWvZrXfokZedXBOz7KdShU93XFjU=
=0VJM
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc6' into next/dt
Update to Linux 3.16-rc6 as a dependency for the broadcom changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Document and use new cadence serial binding
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
iEYEABECAAYFAlPI73sACgkQykllyylKDCGYzQCggc3g80f6R008+SNKlrN0Wuy+
b9kAnjqTO0Q0kDf4PlI/a5EVsfPmOzoS
=Bo6W
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx into next/dt
Merge "Xilinx Zynq changes for v3.17" from Michal Simek:
arm: Xilinx Zynq dt patches for v3.17
- Document and use new cadence serial binding
* tag 'zynq-dt-for-3.17' of git://git.xilinx.com/linux-xlnx:
ARM: zynq: DT: Migrate UART to Cadence binding
tty: cadence: Document DT binding
+ Linux 3.16-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
The pwm driver requires a clocks property referencing the pwm peripheral
clk.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Correct the typo error for the second "uhphs_clk".
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Make the ram controller driver take the ddrck clock for at91sam9n12 and
at91sam9x5.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add clocks for usb device, or else switch to CCF, the gadget
won't work.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Tested-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Having clocks grouped in a subnode is common practice, so move the crystals and
the ADC clock under a clocks node for the at91sam9x5 SoC and at91sam9x5 based
boards.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
ICPLL can only take 0 or 1, it got mixed with OUT which can be in the [0-3]
range.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Define sam9x5 clocks in sam9x5 dt files and make use of them in peripheral
definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Remove the properties that are not used anymore by the at91_adc driver and fix
the atmel,adc-use-external-triggers property name.
Also, add #address-cells, #size-cells and a reg for each trigger to comply to
the ePAPR.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the "atmel,nand-has-dma" property to NAND node for SoC that
can use the DMA to perform NAND accesses.
Use of this property was added in 1b7192658a
(mtd: atmel_nand: add a new dt binding item for nand dma support).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Set default watchdog options in every SoC compatible with the sam9 watchdog.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=L37r
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Paul Walmsley <paul@pwsan.com> via Tony Lindgren:
Move some of the OMAP2+ CM and System Control Module direct
register accesses into CM- and System Control
Module-specific "drivers" underneath arch/arm/mach-omap2/. This
is a prerequisite for moving this code out of arch/arm/mach-omap2/ into
drivers/.
Basic test logs are available here:
http://www.pwsan.com/omap/testlogs/cm_scm_cleanup_a_v3.13/20131019101809/
* tag 'omap-for-v3.13/cm-scm-cleanup-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: control: add API for setting IVA bootmode
ARM: OMAP3: CM/control: move CM scratchpad save to CM driver
ARM: OMAP3: McBSP: do not access CM register directly
ARM: OMAP3: clock: add API to enable/disable autoidle for a single clock
ARM: OMAP2: CM/PM: remove direct register accesses outside CM code
+ Linux 3.12-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch splits the sam9x5 peripheral definitions into:
- a common base for all sam9x5 SoCs (at91sam9x5.dtsi)
- several optional peripheral definitions which will be included by specific
sam9x5 SoCs (at91sam9x5_'periph name'.dtsi)
This provides a better representation of the real hardware (drop unneeded
dt nodes) and avoids future peripheral id conflict (lcdc and isi both use
peripheral id 25).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Replace pinctrl_usart2_rts and pinctrl_usart2_cts istead of pinctrl_uart2_*.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
- DMA binding update with one patch shared with slave-dma tree
- more SPI DT activation
- enable the USB gadget HS for DT platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRu5r2AAoJEAf03oE53VmQvAsIAMa06mb42kGJQ6JhUV0HcL+8
+a2FHN076DreWEtM5vq9ibIEF2pnz+XHafUYGRfjfYRsbEfy41N0OmISNBwIRgP6
yKB6ZnGQp21Fw/SwOGntuEw0PH9bQmM9pNYttMlBfvMlM3TdFWc2fztwvqpP71x4
a1zOsLRNYLk4WO33gh50bRTQeS81GRvn3hrGPKKFXuC7AQ0TCHOH/l1c1Fo5INpk
TiQMy5JvkrJNSerdq23u5uAp2zstuhiVMbSY6eWQwJy1RfOSqVYY91KzGKGpOPT2
g6LB/Z6sZ5wwJ8jbbPV1XAEl45oojPDyNl+KxJc5gir5wfWEVpoayRt1Nfggz98=
=MZkL
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
Again some nice DT updates for AT91:
- DMA binding update with one patch shared with slave-dma tree
- more SPI DT activation
- enable the USB gadget HS for DT platforms
* tag 'at91-dt' of git://github.com/at91linux/linux-at91:
ARM: at91: sam9m10g45ek add udc DT support
ARM: at91: sam9g45 add udc DT support
ARM: at91: sam9x5ek add udc DT support
ARM: at91: sam9x5 add udc DT support
ARM: at91: dt: at91sam9x5: add SPI DMA client infos
ARM: at91: dt: switch DMA DT bindings to pre-processor
ARM: at91: dt: add header to define at_hdmac configuration
