Add SD card write-protect pin configuration to be sure that it will be
properly pulled down to indicate write access.
Suggested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos5250 and Exynos542x SoCs have the same CEC hardware module as
Exynos4 SoC series, so enable support for it using the same compatible
string.
Tested on Odroid XU3 (Exynos5422) and Google Snow (Exynos5250) boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Usage of DTS macros instead of hard-coded numbers makes code easier to
read. One does not have to remember which value means pull-up/down or
specific driver strength.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Replace duplicated macros in each DTSI file with a common macro coming
from header. Include the header in each pinctrl DTSI so further changes
could use it.
Although PIN_FUNC_SPC_2 does not bring much information about the
function itself, it still is more descriptive then hard-coded
number <2>.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
The 'sd0_rclk' was put in the middle of SD1 nodes. Remove the confusion.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
A previously defined Device Tree node, can be extended either by defining
a node using the same full path or by creating a label for the node and
referencing to it.
Using full paths is more error prone since if there was a typo error, a
new node will be created instead of extending the node as it was desired.
This will lead to run-time errors that could be hard to detect.
A mistyped label on the other hand, will cause a dtc compile error which
makes it easier to detect the mistake since happens at build-time instead.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
HS400 timing values are added for SMDK5420, exynos5420-peach-pit
and exynos5800-peach-pi boards. This also adds RCLK GPIO line,
this gpio should be in pull-down state.
This also enables HS400 on peach-pi and this updates the clock
frequency to 800MHz to be set as input clock to controller.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
[alim.akhtar@samsung.com: addressed review comments]
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Adds the PWM nodes to 5420 pinctrl dtsi file.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add pin state information for DP HPD support that requires pin configuration
support using pinctrl interface.
Signed-off-by: Vikas Sajjan <vikas.sajjan@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add the required pin configuration support to EXYNOS5420
using pinctrl interface.
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Tested-by : Sunil Joshi <joshi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
