Secondary CPUs should have the same information in DeviceTree as booting
CPU from both correctness point of view and for possible hotplug
scenarios.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
The "cooling-min-level" and "cooling-max-level" properties are not
parsed by any part of the kernel currently and the max cooling state of
a CPU cooling device is found by referring to the cpufreq table instead.
Remove the unused properties from the CPU nodes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable support for ARM Performance Monitoring Units available in Cortex-A7
and Cortex-A15 CPU cores for Exynos54xx SoCs (5410, 5420 and 5422/5800).
The PMUs interrupts are defined in the common exynos54xx.dtsi device tree,
but the PMUs are enabled and have their interrupt CPU affinity defined
next to each SoC's cpus node.
Tested with perf on Odroid XU4 (Exynos5422):
armv7_cortex_a7 PMU driver: 5 counters available
armv7_cortex_a15 PMU driver: 7 counters available
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Willy Wolff <willy.mh.wolff@gmail.com>
[mszyprow: reordered nodes according to krzk request, fixed typos]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The following 'capacity-dmips-mhz' dt property values are used:
Cortex-A15: 1024, Cortex-A7: 539
They have been derived form the cpu_efficiency values:
Cortex-A15: 3891, Cortex-A7: 2048
by scaling them so that the Cortex-A15s (big cores) use 1024.
The cpu_efficiency values were originally derived from the "Big.LITTLE
Processing with ARM Cortex™-A15 & Cortex-A7" white paper
(http://www.cl.cam.ac.uk/~rdm34/big.LITTLE.pdf). Table 1 lists 1.9x
(3891/2048) as the Cortex-A15 vs Cortex-A7 performance ratio for the
Dhrystone benchmark.
The following platforms are affected once cpu-invariant accounting
support is re-connected to the task scheduler:
odroidxu3, odroidxu3-lite, odroidxu4
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
On Exynos5422 and Exynos5800 we support 12 cpufreq steps (200-1300 MHz) for LITTLE
and 18 steps for big core (200-1700 MHz). Add respective cooling cells.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
For Exynos542x/5800 platforms, add CPU operating points
for migrating from Exynos specific cpufreq driver to using
generic cpufreq driver.
Changes by Bartlomiej:
- split Exynos5420 support from the original patch
- merged Exynos5422 fixes from Ben
Changes by Ben Gamari:
- Port to operating-points-v2
Cc: Doug Anderson <dianders@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Andreas Faerber <afaerber@suse.de>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Ben Gamari <ben@smart-cactus.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Exynos5420 and Exynos5800 boards boot from big core (A15) but
Exynos5422 boards choose otherwise: LITTLE core (A7) (on Exynos5422 this
is property of the board - configurable by pulling up/down gpg2-1).
To make user-visible CPU ordering more consistent the 'cpus' node was
overridden by exynos5422-cpus.dtsi.
However this is a little bit ugly and error-prone. Overriding the CPU
child nodes requires to basically reverse what was done initially in
exynos5420.dtsi.
Instead, split CPU configuration entirely to separate files which should
be included by board DTS.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanho Park <parkch98@gmail.com>
The odroid-xu3 board which is based on exynos5422 not exynos5800
is booted from cortex-a7 core unlike exynos5800. The odroid-xu3's
cpu order is quite strange. cpu0 and cpu5-7 are cortex-a7 cores and
cpu1-4 are cortex-a15 cores. To correct this mis-odering, I added
exynos5422-cpus.dtsi and reversing cpu orders from exynos5420.
Now, cpu0-3 are cortex-a7 and cpu4-7 are cortex-a15.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Chanho Park <parkch98@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
