The 50ms debounce is too low and give ghost bounces on some
platforms. Bump it to 100ms to make it stable.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the FOTG210 USB host controller to the Gemini
device trees. In the main SoC DTSI it is flagged as disabled
and then it is selectively enabled on the devices that utilize
it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some Gemini platforms have a parallel NOR flash which conflicts
with use cases reusing some of the flash lines (such as CE1)
for GPIO.
Fix this on the D-Link DIR-685 and Itian SQ201 by creating
"enabled" and "disabled" states for the flash pin control
handle, and rely on the flash handling code to switch this
in and out when accessed so these lines can be used
for GPIO when flash is not accessed, and enable flash
access.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The vendor firmware was analyzed to get the right idea about
this flash layout. /proc/mtd contains:
dev: size erasesize name
mtd0: 01e7ff40 00020000 "rootfs"
mtd1: 01f40000 00020000 "upgrade"
mtd2: 00040000 00020000 "rgdb"
mtd3: 00020000 00020000 "nvram"
mtd4: 00040000 00020000 "RedBoot"
mtd5: 00020000 00020000 "LangPack"
mtd6: 02000000 00020000 "flash"
Here "flash" is obviously the whole device and we know "rootfs"
is a bogus hack to point to a squashfs rootfs inside of the main
"upgrade partition". We know "RedBoot" is the first 0x40000 of
the flash and the "upgrade" partition follows from 0x40000 to
0x1f8000. So we have mtd0, 1, 4 and 6 covered.
Remains:
mtd2: 00040000 00020000 "rgdb"
mtd3: 00020000 00020000 "nvram"
mtd5: 00020000 00020000 "LangPack"
Inspecting the flash at 0x1f8000 and 0x1fa000 reveals each of
these starting with "RGCFG1" so we assume 0x1f8000-1fbfff is
"rgdb" of 0x40000.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the Ethernet and Realtek switch device to the
D-Link DIR-685 Gemini-based device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DTC was warning a lot about unit names etc, I think I fixed
them all. Stopping to include skeleton.dtsi fixes the last one.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These machines need to be booted from very specific harddisk
partitions (as the D-Link DNS-313 boots specifically from
partition 4). Add the proper bootargs so that everything works
smoothly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using the blue LED for disk read and the orange LED for
disk write gives a better user experience.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the TVE200/TVC TV-encoder and the Ilitek ILI9322 panel
to the DIR-685 device tree.
This brings graphics to this funky router and it is possible to
even run a console on its tiny screen.
Incidentally this requires us to disable the access to the
parallel (NOR) flash, as the communication pins to the panel
are shared with the flash memory.
To access the flash, a separate kernel with the panel disabled
and the flash enabled should be booted. The pin control selecting
whether to use the lines cannot be altered at runtime due to
hardware constraints.
Cc: David Lechner <david@lechnology.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These GPIOs are used in open drain mode, so make sure to
flag them as such. Use the new separate scl/sda line
GPIO bindings.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the basic pin control muliplexing settings for the
Gemini SoC: parallel (NOR) flash, SATA, optional IDE, PCI and
UART.
We also select the right GPIO groups on all applicable systems
so that GPIO keys/LEDs work smoothly.
We can then build upon this for more complex systems.
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a device tree file for the Gemini-based D-Link DIR-685
router, supporting all devices that are currently supported in
the main DTSI SoC file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
