Add missing pinmux entry for OSC32K_32K_OUT on pad ENET_RXD0 used by the
Variscite DART-MX6 SoM.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
From "Chip Errata for the i.MX 6Dual/6Quad"
ERR006687 ENET: Only the ENET wake-up interrupt request can wake the
system from Wait mode.
The ENET block generates many interrupts. Only one of these interrupt lines
is connected to the General Power Controller (GPC) block, but a logical OR
of all of the ENET interrupts is connected to the General Interrupt Controller
(GIC). When the system enters Wait mode, a normal RX Done or TX Done does not
wake up the system because the GPC cannot see this interrupt. This impacts
performance of the ENET block because its interrupts are serviced only when
the chip exits Wait mode due to an interrupt from some other wake-up source.
Adding MX6QDL_PAD_GPIO_6__ENET_IRQ is the 1st step to
workaround this problem.
The input reg is set to 0x3c to set IOMUX_OBSRV_MUX1 to ENET_IRQ.
The mux reg value is 0x11, so that the observable mux is routed to
this pin and to the gpio controller(sion bit). These magic values
come from Ranjani Vaidyanathan's patch:
"ENGR00257847-1 MX6Q/DL-Fix Ethernet performance issue when WAIT mode is active"
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Ranjani Vaidyanathan <ra5478@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The solo/duallite reference manual does not mention
this setting, but it works.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6q and imx6dl are two pin-to-pin compatible SoCs. The same board
design can work with either chip plugged into the socket, e.g. sabresd
and sabreauto boards.
We currently define pin groups in imx6q.dtsi and imx6dl.dtsi
respectively because the pad macro names are different between two
chips. This brings a maintenance burden on having the same label point
to the same pin group defined in two places.
The patch replaces prefix MX6Q_ and MX6DL_ with MX6QDL_ for both SoCs
pad macro names. Then the pin groups becomes completely common between
imx6q and imx6dl and can just be moved into imx6qdl.dtsi, so that the
long term maintenance of imx6q/dt pin settings becomes easier.
Unfortunately, the change brings some dramatic diff stat, but it's all
about DTS file, and the ultimate net diff stat is good.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The uart2 in the imx6q-arm2 board is used as a DTE uart,
this patch adds the necessary DTE pads for uart2.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6dl is a derivative of imx6q with very limited difference. These
two SoCs are so compatible that they can be handled as one platform in
software. That said, we will not have target SOC_IMX6DL but just
reusing SOC_IMX6Q. That's why the pinctrl-imx6dl driver is added here
with symbol PINCTRL_IMX6Q controlling the build of it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
