Enable the watchdog, so the board can be restarted by a watchdog
timeout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The r8a7792 Wheat board has two ADV7513 devices sharing a single I2C
bus, however in low power mode the ADV7513 will reset it's slave maps to
use the hardware defined default addresses.
The ADV7511 driver was adapted to allow the two devices to be registered
correctly - but it did not take into account the fault whereby the
devices reset the addresses.
This results in an address conflict between the device using the default
addresses, and the other device if it is in low-power-mode.
Repair this issue by moving both devices away from the default address
definitions.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Fixes: f6eea82a87 ("ARM: dts: wheat: add DU support")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Convert the R-Car V2H SoC from the old "Renesas R-Car Gen2 Clock Pulse
Generator (CPG)" and "Renesas CPG Module Stop (MSTP) Clocks" DT bindings
to the new unified "Renesas Clock Pulse Generator / Module Standby and
Software Reset" DT bindings.
This simplifies the DTS files, and allows to add support for reset
control later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Wheat board dependent part of the DU device node.
Add the device nodes for the Analog Devices ADV7513 HDMI transmitters
connected to DU0/1. Add the necessary subnodes to interconnect DU with
HDMI transmitters/connectors.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support for the tactile switches SW2/3 (on the debug board) as a
virtual keyboard like it was done with the Blanche board).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Wheat board dependent part of the QSPI device node.
Add device nodes for Spansion S25FL512S SPI flash and MTD partitions on it.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Wheat board dependent part of the SDHI0 (connected to the
micro-SD slot) device node along with the necessary voltage regulator.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Wheat board dependent part of the CAN0/1 device nodes...
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R8A7792 SoC doesn't have the EtherMAC core, so SMSC LAN89218 Ethernet
chip was used instead on the Wheat debug board; this chip is compatible
with SMSC LAN9115 for which there's a (device tree aware) driver.
Describe the chip in the Wheat device tree unconditionally (the driver
should fail the probe if the debug board isn't connected); enable DHCP and
NFS root in the command line for the kernel boot...
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7792 SoC based Wheat board.
The Wheat board itself has no serial ports wired up, the USB serial chips
are situated on a separate debug board and one of them is connected to
SCFI0 -- include unconditional support for it, so that the serial console
can work.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
